Husqvarna 5524Ste Users Manual OM, 5524 STE, 96193001400, 2006 08, Snow Thrower

5524STE to the manual a2a4f200-7036-4fb0-a4ec-477f30cdc796

2015-01-24

: Husqvarna Husqvarna-5524Ste-Users-Manual-317644 husqvarna-5524ste-users-manual-317644 husqvarna pdf

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

5524STE
Owner's Manual

IMPORTANT
Safe Operation Practices for Walk-Behind Snow Throwers
This snow thrower is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury.
WARNING: Snow throwers have exposed rotating parts, which can cause
severe injury from contact, or from material thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.

Look for this symbol to point out important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
WARNING: Always disconnect spark
plug wire and place it where it cannot
contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.

WARNING: This snow thrower is for
use on sidewalks, driveways and other
ground level surfaces. Caution should
be exercised while using on sloping surfaces. Do not use snow thrower on
surfaces above ground level such as
roofs of residences, garages, porches
or other such structures or buildings.

WARNING: Engine exhaust, some of
its constituents, and certain vehicle
components contain or emit chemicals known to the State of California
to cause cancer and birth defects or
other reproductive harm.

Training
1. Read, understand and follow all instructions on the
machine and in the manual(s) before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.
2. Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.
3. Keep the area of operation clear of all persons, particularly small children.
4. Exercise caution to avoid slipping or falling, especially
when operating the snow thrower in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is
to be used and remove all doormats, sleds, boards,
wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting the engine (motor).
3. Do not operate the equipment without wearing adequate
winter garments. Avoid loose fitting clothing that can
get caught in moving parts. Wear footwear that will
improve footing on slippery surfaces.
4. Handle fuel with care; it is highly flammable
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
(d) Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before
filling.
(e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment
on a trailer with a portable container, rather than
from a gasoline dispenser nozzle.

(f) Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open
device.
(g) Replace gasoline cap securely and wipe up spilled
fuel.
(h) If fuel is spilled on clothing, change clothing immediately.
Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive motors
or electric starting motors.
Adjust the collector housing height to clear gravel or
crushed rock surface.
Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to
protect eyes from foreign objects that may be thrown
from the machine.

Operation

1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the
cord on electric motors, thoroughly inspect the snow
thrower for any damage, and repair the damage before
restarting and operating the snow thrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the operating position, before unclogging the collector/impeller
housing or discharge chute, and when making any
repairs, adjustments or inspections.

6. When cleaning, repairing or inspecting the snow thrower,
stop the engine and make certain the collector/impeller
and all moving parts have stopped. Disconnect the
spark plug wire and keep the wire away from the plug
to prevent someone from accidentally starting the engine.
7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.
8. Exercise extreme caution when operating on slopes.
9. Never operate the snow thrower without proper guards,
and other safety protective devices in place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
13. Disengage power to the collector/impeller when snow
thrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

CONGRATULATIONS on your purchase of a new snow
thrower. It has been designed, engineered and manufactured to give best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”.

PRODUCT SPECIFICATIONS

Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the discharge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.

Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.
4. Maintain or replace safety and instruction labels, as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.

Gasoline Capacity 2.0 Quarts
and Type:
Unleaded Regular only

SERIAL NUMBER: ___________________________

Oil Type
(API SG–SL):

SAE 30 (above 40°F)
SAE 5W-30 or 10W-30 (0° to +40°F)
SAE 0W-30 (below 0°F)

Oil Capacity:

21 Ounces

Spark Plug:

Champion RJ19LM (Gap: .030")

DATE OF PURCHASE: _______________________

CUSTOMER RESPONSIBILITIES

THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE SNOW
THROWER HOUSING.

•
•
•

YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.

Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your snow thrower.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS...................................... 3
CUSTOMER RESPONSIBILITIES................................ 3
WARRANTY................................................................ 32
ASSEMBLY / PRE-OPERATION ............................... 4-6
OPERATION ............................................................ 7-12

MAINTENANCE ..................................................... 13-14
MAINTENANCE SCHEDULE ..................................... 13
SERVICE AND ADJUSTMENTS ........................... 15-17
STORAGE................................................................... 17
TROUBLESHOOTING ................................................ 18
REPAIR PARTS ..................................................... 20-31

PARTS PACKED SEPARATELY IN CARTON

ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety
before you attempt to assemble or operate your new
snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly,
operation and maintenance of the product.
Your new snow thrower has been assembled at the factory
with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have been placed in
the parts bag. To ensure safe and proper operation of your
snow thrower, all parts and hardware you assemble must
be tightened securely. Use the correct tools as necessary
to ensure proper tightness.

2. Cut down all four corners of carton and lay panels flat.
3. Remove the two (2) screws securing the auger housing
to the pallet.
4. Remove all packing materials except plastic tie holding
speed control rod to lower handle.
5. Remove the two (2) plastic ties securing the upper
handle to the pallet.
6. Remove snow thrower from carton and check carton
thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

REMOVE SNOW THROWER FROM CARTON
1. Remove all accessible loose parts and parts boxes
from carton.

TOOL BOX (See Fig. 8)
A toolbox is provided on your snow thrower. The toolbox is
located on top of the belt cover. Store the extra shear bolts,
nuts and multi-wrench provided in parts bag in the toolbox.

ASSEMBLY / PRE-OPERATION
INSTALL TRACTION DRIVE CONTROL ROD
(See Figs. 3 and 4)
The traction drive control rod has the long loop on the end
of the spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
pivot bracket with loop opening down as shown.
2. With top end of rod positioned under left side of control
panel, push rod down and insert top end of rod into hole
in drive control bracket. Secure with retainer spring.

NOTE: The multi-wrench may be used for assembly of the
chute rotator head to snow thrower and making adjustments
to the skid plates.
UNFOLD UPPER HANDLE
1. Raise upper handle to the operating position and tighten
handle knobs securely.
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
1. Remove plastic tie securing rod to lower handle.
2. Insert rod into speed control bracket and secure with
retainer spring.
SPEED
CONTROL
ROD

TRACTION DRIVE
CONTROL ROD

PLASTIC TIE
UPPER
HANDLE

RUBBER
SLEEVE

HANDLE
KNOB

LOWER
HANDLE
LOOP
OPENING
DOWN

PIVOT
BRACKET
FIG. 3
FIG. 1

TRACTION DRIVE
CONTROL LEVER

RETAINER
SPRING

SPEED CONTROL ROD
RETAINER
SPRING
TRACTION
DRIVE
CONTROL
ROD

DRIVE
CONTROL
BRACKET
SPEED
CONTROL
BRACKET

SPEED
CONTROL
LEVER

FIG. 4

FIG. 2

ASSEMBLY / PRE-OPERATION
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
The auger control rod has the short loop on the end of the
spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
control arm with loop opening up as shown.
2. With top end of rod positioned under right side of
control panel, push down on rod and insert end of rod
into hole in auger control bracket. Secure with retainer
spring.

INSTALL DISCHARGE CHUTE / CHUTE ROTATER
HEAD (See Fig. 7)
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotater head.
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Position chute rotater head over chute bracket. If necessary, rotate chute assembly to align square and pin on underside of chute rotater head with holes in chute bracket.
3. With chute rotater head and chute bracket aligned,
position chute rotater head on pin and threaded stud
of mounting bracket.
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.

AUGER
CONTROL
ROD

CHUTE
ROTATER
HEAD

RUBBER
SLEEVE

3/8 LOCKNUT
3/8 WASHER

CONTROL
ARM

LOOP
OPENING
UP

PIN
THREADED
STUD

CHUTE
BRACKET
FIG. 5

ROTATER HEAD
MOUNTING
BRACKET

FIG. 7

AUGER CONTROL ROD
RETAINER
SPRING

ALIGN BEFORE
TIGHTENING LOCKNUT

AUGER
CONTROL
LEVER

CHECK TIRE PRESSURE
The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pressure
is important for best snow throwing performance.
• Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

AUGER
CONTROL
BRACKET
FIG. 6

OPERATION
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.

PRIMER

DANGER
OR WARNING

FORWARD

REVERSE

READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.

DISENGAGED

ENGAGED

SNOW
DISCHARGE

TRACTION
DRIVE CONTROL
7

OPERATION
SPARK
PLUG

ENGINE OIL CAP
WITH DIPSTICK

SAFETY
IGNITION
KEY

AUGER
CONTROL
LEVER

DISCHARGE CHUTE CONTROL LEVER
DRIVE SPEED
CONTROL LEVER

GASOLINE
FILLER
CAP
CHUTE
DEFLECTOR

CHOKE
CONTROL

TRACTION
DRIVE
CONTROL
LEVER

FUEL
SHUT-OFF
VALVE
THROTTLE
/ ENGINE
CONTROL

RECOIL
STARTER
HANDLE

DISCHARGE
CHUTE
POWER
CORD
PLUG
ELECTRIC
START
BUTTON
PRIMER

OIL DRAIN PLUG
HANDLE
KNOB

CLEAN-OUT TOOL

MUFFLER
NOTE: ITEMS ABOVE
ARE SHOWN IN
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.

TOOLBOX

SKID PLATE
AUGERS

FIG. 8

MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Electric start button – used for starting the engine.
Recoil (auxiliary) starter handle – used for starting the
engine.
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Throttle/engine control - used to select either FAST or
SLOW engine speed and to STOP the engine.

Choke control - used for starting a cold engine.
Drive speed control lever - used to select forward or
reverse motion and speed of snow thrower.
Traction drive control lever - used to engage power-propelled forward or reverse motion of snow thrower.
Auger control lever - used to engage auger motion (throw
snow).
Discharge chute control lever - used to change the direction the snow is thrown.
Skid plate - used to adjust height of scraper bar from the
ground.

OPERATION
The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear
safety glasses or eye shields while operating
your snow thrower or performing any adjustments or repairs. We recommend standard safety glasses
or a wide vision safety mask worn over spectacles.

TO USE CHOKE CONTROL (See Fig. 11)
The choke control is located on the engine. Use the choke
control whenever you are starting a cold engine. Do not
use to start a warm engine.
• To engage choke, turn knob clockwise. Slowly turn
knob counterclockwise to disengage.

HOW TO USE YOUR SNOW THROWER
Know how to operate all controls before adding fuel or
attempting to start the engine.

OFF

STOPPING
TRACTION DRIVE
• Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
AUGER
• Release the auger control lever to stop throwing snow.
ENGINE
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.

FULL

FIG. 11

TO CONTROL SNOW DISCHARGE (See Figs. 12 & 13)
WARNING: Snow throwers have exposed rotating parts, which can cause
severe injury from contact, or from material thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.

TO USE FUEL SHUT-OFF VALVE (See Fig. 9)
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always operate the snow thrower with the fuel
shut-off valve in the OPEN position.

WARNING: If the discharge chute or auger become clogged, shut-off engine
and wait for all moving parts to stop. Use
the clean-out tool, NOT YOUR HANDS,
to unclog the chute and/or auger.
The DIRECTION in which snow is to be thrown is controlled
by the discharge chute control lever.
• To change the discharge chute position, press downward on discharge chute control lever and move lever
left or right until chute is in desired position. Be sure
lever springs back and locks into desired position.

OFF

OPEN

DISCHARGE CHUTE
CONTROL LEVER

FIG. 9

TO USE THROTTLE CONTROL (See Fig. 10)
The throttle control is located on the engine. Always operate
the snow thrower with the engine at full throttle. Full throttle
offers the best snow thrower performance.
FAST

FIG. 12
SLOW

FIG. 10

The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
• To change the deflector position, loosen knob, move deflector to desired position and tighten knob securely.

OPERATION
•
HIGH
POSITION

Restart the engine, then squeeze the auger control
lever to the handle to clear snow from the auger housing and the discharge chute.
DISCHARGE CHUTE

KNOB
CLEAN-OUT
TOOL

MOUNTING CLIP

CHUTE
DEFLECTOR
LOW POSITION

FIG. 13

TO THROW SNOW (See Fig. 14)
The auger rotation is controlled by the auger control lever
located on the right side handle.
• Squeeze auger control lever to handle to engage the
auger and throw snow.
• Release the auger control lever to stop throwing snow.
AUGER
CONTROL
LEVER

FIG. 15

TO MOVE FORWARD AND BACKWARD (See Fig. 16)
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
• Squeeze traction drive control lever to handle to engage
the drive system.
• Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
SPEED and DIRECTION are controlled by the drive speed
control lever.
• Press downward on the speed control lever and move
lever to desired position BEFORE engaging the traction drive control lever. Be sure lever springs back and
locks into desired position.
CAUTION: Do not move speed control lever
when traction drive control lever is engaged.
Damage to the snow thrower can result.

FIG. 14

USING THE CLEAN-OUT TOOL (See Fig. 15)
In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool to
dislodge this blockage.
When cleaning, repairing, or inspecting, make
certain all controls are disengaged and the
auger/impeller and all moving parts have
stopped. Disconnect the spark plug wire and
keep the wire away from the spark plug to prevent accidental starting.
Release the auger control lever and shut off the engine.
Remove the clean-out tool from it's mounting clip. Grasp
the tool firmly by the handle and push and twist the tool
into the discharge chute to dislodge the blockage.
After the packed snow has been dislodged, return the cleanout tool to it's mounting clip by pushing it into the clip.
• Make sure the discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are
in the direction of discharge) before restarting engine. 10

•

Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
TRACTION DRIVE
CONTROL LEVER

•
•

DRIVE SPEED
CONTROL LEVER
FIG. 16

OPERATION
TO ADJUST SKID PLATES (See Fig. 17)
NOTE: The wrench provided in your parts bag may be used
to adjust the skid plates.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
NOTE: It is not recommended to operate the snow thrower
over gravel or rocky surfaces. Objects such as gravel, rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
• If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1. Shut off engine and wait for all moving parts to stop.
2. Adjust skid plates by loosening the rear 1/2" hex nut
only, then moving skid plate to desired position. Be sure
both plates are adjusted evenly. Tighten securely.
HIGH POSITION
(LOW GROUND
CLEARANCE)

WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Empty the gas tank, start
the engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.

CHOKE CONTROL

THROTTLE

PRIMER

ENGINE OIL
FILL CAP /
DIPSTICK

SAFETY
IGNITION
KEY

AUGER
HOUSING
SKID PLATE
1/2" HEX NUT
GASOLINE
FILLER CAP
LOW POSITION (HIGH GROUND CLEARANCE)
FUEL SHUTOFF VALVE

FIG. 17

SCRAPER BAR
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 18)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
• To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
ADD GASOLINE (See Fig. 18)
• Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
11

RECOIL
STARTER
HANDLE

STARTER BUTTON
POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 18

TO START ENGINE
• Be sure fuel shut-off valve is in the OPEN position.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
• Be sure your house is a 120 Volt A.C. three-wire
grounded system. If you are uncertain, consult a
licensed electrician.
WARNING: Do not use the electric
starter if your house is not a 120 Volt
A.C. three-wire grounded system. Serious personal injury or damage to your
snow thrower could result.

OPERATION
ELECTRIC STARTER
1. Connect the power cord to the engine.
2. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
3. While the engine is running, push starter button and
spin the starter for several seconds.
NOTE: The unusual sound made while starter is spinning
will not harm the engine or starter.
4. Disconnect the power cord from the receptacle first,
then from the engine.
RECOIL STARTER
1. While the engine is running, pull the recoil starter handle
with rapid, full arm strokes three or four times.
NOTE: The unusual sound made while pulling the recoil
starter handle will not harm the engine or starter.

COLD START - ELECTRIC STARTER
1. Insert safety ignition key into the ignition slot until it
clicks. DO NOT turn the key. Keep the extra safety
ignition key in a safe place.
2. Place throttle control in FAST position.
3. Rotate choke control to FULL position.
4. Connect the power cord to the engine.
5. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
6. Push the primer three (3) times.
7. Push starter button until engine starts.
IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Wait
5 to 10 seconds between each attempt.
8. When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
9. Disconnect the power cord from the receptacle first,
then from the engine.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating temperature.
WARM START - ELECTRIC STARTER
Follow the steps above, keeping the choke control in the
OFF position.
COLD START - RECOIL STARTER
1. Insert safety ignition key into the ignition slot until it
clicks. DO NOT turn the key. Keep the extra safety
ignition key in a safe place.
2. Place throttle control in FAST position.
3. Rotate choke control to FULL position.
4. Push the primer four (4) times if the temperature is
below 15°F/–10°C, or two (2) times if temperature is
between 15° and 50°F/–10°C and 10°C. If temperature
is above 50°F/10°C, priming is not necessary.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
6. When the engine starts, release the recoil starter
handle and slowly move the choke control to the OFF
position.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating
temperature.
WARM START - RECOIL STARTER
Follow the steps above, keeping the choke in the OFF
position. DO NOT push the primer.

IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
2. Release the recoil starter handle and let it snap back
against the starter.
If the engine still fails to start, repeat the above steps or
use the electric starter.

SNOW THROWING TIPS
•
•
•
•

•
•
•

•

•
•
•

BEFORE STOPPING
Run the engine for a few minutes to help dry off any moisture on the engine.
To avoid possible freeze-up of the starter, proceed as follows:

Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Go slower in deep, freezing or heavy wet snow. Use the
drive speed control, NOT the throttle, to adjust speed.
It is easier and more efficient to remove snow immediately after it falls.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures.
Slightly overlap each successive path to ensure all
snow will be removed.
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
For extremely heavy snow, reduce the width of snow
removal by overlapping previous path and moving
slowly.
Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
After snow-throwing is completed, allow engine to run for
a few minutes to melt snow and ice off the engine.
Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.
WARNING: Do not operate snow
thrower if weather conditions impair visibility. Throwing snow during a heavy,
windy snowstorm can blind you and be
hazardous to the safe operation of the
snow thrower.

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain
your snow thrower.
At least once a season, check to see if you should make
any of the adjustments described in the Service and Adjustments section of this manual.
• At least once a year, you should replace the spark plug
and check belts for wear. A new spark plug will help
your engine run better and last longer.
• Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.

➀ SAE 30 Motor Oil
➁ See “ENGINE” in
Maintenance section

➂ General
Purpose
Grease

➀ Pivot points

BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Check controls to be sure they are functioning properly.

➁

LUBRICATION
➂ Auger

Keep your snow thrower well lubricated
(See “LUBRICATION CHART”).

Engine
oil

grease fittings

SNOW THROWER
Always observe the safety rules when performing any
maintenance.

•

Keep tires free of gasoline and oil, which can harm
rubber.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.

TIRES
• Maintain proper air pressure in both tires (14–17 P.S.I.
/ 19-24.5 N-m).
13

MAINTENANCE
V-BELTS
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
The V-belts on your snow thrower are of special construction
and should be replaced by original equipment manufacturer
(OEM) belts available from your nearest dealer. Using other
than OEM belts can cause personal injury or damage to
the snow thrower.

TO CHANGE ENGINE OIL
Determine temperature range anticipated before next oil
change. All oil must meet API service classification SG–SL.
• Be sure snow thrower is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and placement of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Clean area around drain plug.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
5. Wipe off any spilled oil from snow thrower and engine.
6. Install left wheel (if removed for draining oil). Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
9. Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
10. Wipe off any spilled oil.

AUGER GEAR CASE
• The gear case was filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
• If lubricant is required, use only Ronex ED #1 grease.
TRACTION DRIVE SYSTEM
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
CAUTION: Any lubricating of the above components can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.

ENGINE
See engine manual.
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.

MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of each season or after
every 100 hours of operation, whichever occurs first. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.

CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the snow thrower is not used for 25 hours
in one year.
Check the crankcase oil level before starting the engine and
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.

WARNING: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
•
•

Keep finished surfaces/wheels free of gasoline, oil, etc.
We do not recommend using a garden hose to clean
your snow thrower unless the electrical system, muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.

SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury,
before performing any service or adjustments:
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Make sure the augers and all moving
parts have completely stopped.
4. Disconnect spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.

1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
4. Connect spark plug wire to spark plug.

SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.

1/4-20
LOCKNUT

1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT

1/4-20 x 2
SHOULDER /
SHEAR BOLT
SPACER

IMPELLER HUB
IMPELLER
SHAFT

CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
•

To change direction and/or distance snow is discharged,
see “TO CONTROL SNOW DISCHARGE” in the Operation section of this manual.

SHEAR BOLTS (See Fig. 19)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
3. Align hole in auger hub with hole in auger shaft and install
a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install
1/4-20 lock nut and tighten securely.

AUGER
HUB

1/4-20
LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 19

TO REMOVE BELT COVER (See Fig. 20)
1. Remove the two (2) screws securing belt cover to
frame.
2. Remove belt cover.
• Replace belt cover by installing cover and screws and
tighten securely.
BELT
COVER

CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4. Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shear bolts and hex nuts. Should a foreign object
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other components. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
15

FRAME

SCREWS
FIG. 20

SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 21)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
The V-belts on your snow thrower are of special construction
and should be replaced by original equipment manufacturer
(OEM) belts available from your nearest dealer. Using other
than OEM belts can cause personal injury or damage to
the snow thrower.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9. Place auger belt around and inside the groove of auger
pulley only.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
become dislodged from the pulley (by catching the idler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 10. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALL ENGINE PULLEY - Place belt in pulley groove
and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs.
torque). Make sure belt is inside belt keeper.
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.

WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistant stand in the operating position
and hold the snow thrower handles. Serious personal injury and/or damage to
the unit could occur if the snow thrower
should fall during the belt changing
process.
FRAME
ASSEMBLY

AUGER
HOUSING

BELT KEEPER
HANDLES
TRACTION DRIVE BELT

1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors,
away from fire or flame. Wipe up any spilled gasoline.
2. REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
4. REMOVE ENGINE PULLEY - Remove bolt, lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts and lock washers holding
auger housing and frame together.

ENGINE
PULLEY

FLAT WASHER
LOCKWASHER
BOLT
AUGER
BELT

IDLER ARM
SQUARE
HOLE
CLUTCHING
IDLER ARM
BRACKET
AUGER PULLEY
BOLT

WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
6. REMOVE AUGER BELT from around pulley.
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.

FRAME

AUGER
HOUSING
FIG. 21

LOCK
WASHER

TO REMOVE WHEELS (See Fig. 22)
• Remove the klik pin and remove wheel from axle.
IMPORTANT: When installing wheel, be sure to use the innermost hole in axle and the wheel hub hole. To disengage
drive system from the wheels (for pushing or transporting
the snow thrower), remove klik pin from wheel hub and
insert pin into the outermost hole in axle only.
KLIK PIN

OUTER HOLE

INNER
HOLE

WHEEL

WHEEL HUB
FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower to
a qualified service center.
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.

STORAGE
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more.
WARNING: Never store the snow
thrower with gasoline in the tank inside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gas appliance. Allow the engine to cool
before storing in any enclosure.

SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
1. Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
2. Inspect and replace belts, if necessary (See “TO REPLACE BELTS” in the Service and Adjustments section
of this manual).
3. Lubricate as shown in the Maintenance section of this
manual.
4. Be sure that all nuts, bolts, screws, and pins are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE
See engine manual.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Also, alcohol blended fuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
17

•

Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of
this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pull recoil starter handle slowly a few times to distribute
oil.
4. Replace with new spark plug.

OTHER
•
•

Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
• If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
• Cover your snow thrower with a suitable protective cover
that does not retain moisture. Do not use plastic. Plastic
cannot breathe, which allows condensation to form and
will cause your snow thrower to rust.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.

TROUBLESHOOTING
See appropriate section in manual unless directed to a qualified service centre.
PROBLEM

Does not start

Loss of power

CAUSE

1. Fuel shut-off valve (if so
equipped) in OFF position.
2. Safety ignition key
is not inserted.
3. Out of fuel.
4. Throttle in STOP position.
5. Choke in OFF position.
6. Primer not depressed.
7. Engine is flooded.
8. Spark plug wire is
disconnected.
9. Bad spark plug.
10. Stale fuel.
11. Water in fuel.

CORRECTION

1. Turn fuel shut-off valve to OPEN position.
2. Insert safety ignition key.
3.
4.
5.
6.
7.
8.

Refill fuel tank with fresh, clean gasoline.
Move throttle to FAST position.
Move to FULL position.
Prime as instructed in the Operation section of this manual.
Wait a few minutes before restarting, DO NOT prime.
Connect wire to spark plug.

9. Replace spark plug.
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

1. Spark plug wire loose.
2. Throwing too much snow.
3. Fuel tank cap is covered
with ice or snow.
4. Dirty or clogged muffler.

1. Reconnect spark plug wire.
2. Reduce speed and width of swath.
3. Remove ice and snow on and around fuel tank cap.

Engine idles or
runs roughly

1.
2.
3.
4.
5.

Excessive
vibration

1. Loose parts or damaged
augers or impeller.

1. Tighten all fasteners. Replace damaged parts.
If vibration remains, contact a qualified service centre.

Recoil starter
is hard to pull

1. Frozen recoil starter.

1. See “IF RECOIL STARTER HAS FROZEN”
in the Operation section of this manual.

Loss of traction
drive / slowing
of drive speed

1. Drive belt is worn.
2. Drive belt is off of pulley.
3. Friction drive wheel is worn.

1. Check / replace drive belt.
2. Check / reinstall drive belt.
3. Contact a qualified service centre.

Loss of snow
discharge or
slowing of
snow discharge

1.
2.
3.
4.

Choke is in FULL position.
Blockage in fuel line.
Stale fuel.
Water in fuel.
Carburetor is in need of
adjustment or overhaul.

Auger belt is off of pulley.
Auger belt is worn.
Clogged discharge chute.
Augers / impeller jammed.

4. Clean or replace muffler.
Move choke to OFF position.
Clean fuel line.
Empty fuel tank & carburetor, refill with fresh, clean gasoline.
Empty fuel tank & carburetor, refill with fresh, clean gasoline.
Contact a qualified service centre.

Check / reinstall auger belt.
Check / replace auger belt.
Clean snow chute.
Remove debris or foreign object from augers / impeller.

SERVICE NOTES

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

13
6

6
10

14
5

42
44

45
50

6
41

42 43
46
27

10
28
55

34
48 19

33
35

19
28
55
10

25
31
17
57

26
22
20

17
20

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.
4
5
6
7

532 19 10-79
532 18 89-09
532 19 85-41
532 18 03-55

8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
25
26
27
28
30

872 27 05-05
532 19 98-79
532 40 78-65
532 40 78-25
532 18 40-95
532 17 53-22
819 11 15-07
532 19 85-52
874 95 05-12
532 40 56-37
532 17 95-82
873 80 04-00
532 19 85-41
532 40 13-47
532 40 78-34
872 27 05-06
532 17 46-58
532 17 46-97
532 19 86-36
532 40 78-50

DESCRIPTION
Pulley, Impeller
Bearing Assembly, Flange
Nut, Hex Flange 5/16-18
Bolt, Flat Head, Carriage
5/16-18 x 5/8
Bolt, Carriage 5/16-1 8 x 5/8
Bolt
Housing, Auger
Bar, Scraper
Bracket, Corner Discharge
Base, Discharge Chute
Washer, Flat
Washer, Lock 5/16
Screw, Hex Head 5/16-18 x 3/4
Grease Fitting
Screw, Hex Head 5/16 x 1
Nut, Hex Lock 1/4-20
Nut, Hex Lock 5/16-18
Washer, Flat 5/16
Skid Plate, Heavy Duty
Bolt, Shoulder 1/4-20
Bearing, Auger
Washer, Thrust, 1"
Bolt, Shear
Auger Assembly, RH

KEY PART
NO. NO.

DESCRIPTION

31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
55
56
57

Auger Assembly, LH
O-Ring
Bushing, Flange 3/4
Washer, Thrust 3/4
Bearing, Thrust 3/4
Shaft, Impeller
Washer, Thrust 5/8
Bushing, Flange 5/8
Screw, Hex Head 5/16-18 x 3/4
Plug, Case
Housing, Gearbox, RH
Seal, Oil
Bushing, Flange, 1"
Key, Square 1/4 x 1/4 x 7/8
Gear, Worm
Shaft, Auger
Housing, Gearbox, LH
Impeller Assembly
Screw, Hex Head 1/4-20 x 1-5/8
Gasket, Gearbox
Pin, Roll 3/16 x 1-1/8
Spacer
Multi-Wrench
Gearbox Assembly

532 40 78-66
532 40 77-68
532 40 77-69
532 17 46-81
532 17 46-84
532 17 46-60
532 17 46-83
532 40 77-58
532 40 77-67
532 40 77-60
532 40 77-61
532 40 77-70
532 40 77-62
532 18 92-82
532 40 77-63
532 40 77-64
532 40 77-65
532 18 41-05
874 78 04-26
532 40 77-66
532 18 42-05
532 19 86-38
532 18 06-84
532 19 67-10

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14
1

19
2

6
32

27
24

9
7

18
3

30
17

14
8
10

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
21
24
25
26
27
28
29
30
31
32

Knob, Lever
Screw #10-24 x 5/8
Strap, Slotted
Nut, Lock 3/8-16
Washer, Flat 3/8
Control Assembly, Chute Rotater
Support, Pivot
Screw, Hex Head 5/16-18 x 3/4
Knob, Deflector
Bolt, Shoulder
Nut, Lock 1/4-20
Bolt, Carriage 5/16-18
Washer, Nylon
Chute Assembly
Deflector Assembly
Seal, Deflector
Rivet, Blind
Knob, Speed Control Lever
Bolt, Carriage 5/16-18 x 3/4
Washer, Flat 5/16
Screw, Hex Head 5/16-18 x 1-3/4
Nut, Lock 5/16-18
Lever Assembly, Speed Control
Retainer, Hairpin
Rod, Upper, Speed Control
Rod, Lower, Speed Control
Clamp, Clean-Out Tool
Tool, Clean-Out
Nut, Lock 5/16-18

532 18 33-34
817 50 10-10
532 18 41-14
873 80 06-00
819 13 13-16
532 40 49-74
532 40 76-43
532 15 00-78
532 19 19-38
532 18 56-00
532 19 17-30
872 25 05-05
532 17 92-46
532 40 76-50
532 18 41-13
532 17 91-45
532 12 84-15
532 18 33-33
532 19 86-48
532 15 54-15
874 78 05-28
532 19 85-41
532 19 84-74
532 16 96-75
532 18 04-45
532 18 77-16
532 19 27-10
532 19 21-99
532 75 11-53

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14
2
5

5
6

12
28

9
8

1
28

13
48

4
15
4

16
22

11
10

14
24
25
27

17
26
27

32
31
31
32

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.

DESCRIPTION

1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
22
23
24
25
26
27
28
30
31
32
36
47
48
49

Lever, Auger Control, RH
Lever, Traction Drive Control, LH
Bushing, Flange
Retainer, Hairpin
Screw, Hex Head
Rod, Interlock
Arm, Impeller Rod
Arm, Traction Rod
Panel, Control
Screw, Hex Head 5/16-18 x 1-1/2
Screw, Hex Head 5/16-18 x 1-3/4
Handle Tube, LH
Handle Tube, RH
Nut, Lock 5/16-18
Washer, Flat 3/8
Knob, Handle
Rod, Auger Control
Rod, Traction Control
Bolt, Carriage 3/8-16 x 2-1/4
Handle Tube, Lower
Sleeve, Spring
Spring, Traction Drive
Spring, Auger Control
Screw, Hex Head 3/8-16 x 1
Bushing, Pivot Lever
Console, Panel
Screw, Hex Head, Tapping #10-24 x 1-1/4
Screw, Hex Head, Tapping #10-24 x 1/2
Spring, Torsion
Mounting Bracket, Handle, LH
Mounting Bracket, Handle, RH
Grip, Handle

532 40 76-49
532 40 76-48
532 17 88-88
532 16 96-75
817 06 04-08
532 17 86-52
532 19 95-76
532 19 95-75
532 19 95-31
874 78 05-24
874 78 05-12
532 40 78-36
532 40 78-35
532 75 11-53
819 13 13-16
532 17 88-99
532 18 04-80
532 18 04-81
872 12 06-18
532 18 40-87
532 18 04-47
532 18 09-26
532 17 86-69
817 00 06-16
532 19 85-59
532 18 33-52
532 17 52-62
532 18 44-71
532 17 88-31
532 19 69-43
532 19 69-44
532 19 95-13

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14
5
2

1
2
7
5

8
1

9 10

27
14
13

22
12

16
21
24

20
41
18

7
17

15
23

18
44

19
2

5
4

25
43
11

15 29 22

41 33
26
28
36
38
39
40

31
30
22

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.

DESCRIPTION

1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
43
44

Screw, Hex Head 5/16-18 x 3/4
Nut, Lock 5/16-18
Screw, Hex Head 5/16-18 x 1/2
Bearing, Flange
Shaft, Auxiliary
Spacer, Plate
Plate, Auxiliary
Gear, Intermediate (12/58)
Gear, Pinion
Rod, Clutch
Shaft, Long, Hex
Pin, Pivot
Lever, Shifter / Wheel
Trunnion Bearing Assembly
Bracket, Pivot, Shift
Ring, Rubber Wheel
Plate, Rubber Wheel
Nut, Lock 5/16-18
Hub, Rubber Wheel
Screw, Hex Head 5/16-18 x 7/8
Retainer, Hairpin
Spring, Bias
Gear, Axle (58 Teeth)
Pin, Pivot Lever
Plate Assembly, Drive
Shaft, Axle
Shaft, Short Hex
Lever, Shifter Plate
Bracket, Shifter Support
Bolt, Carriage 5/16-18 x 5/8
Key, Square 1/4 x 1/4 x 7/8
Bearing, Flange
Plate, Drive Mounting
Spacer, Bearing
Pulley, Traction Drive
Nut, Lock 5/16-18
Washer, Flat
Washer, Lock 5/16
Screw, Hex Head 5/16-18 x 3/4
Ring, Retaining
Spring, Return
Pin, Roll

532 14 63-15
532 75 11-53
532 19 85-84
532 18 00-17
532 18 01-34
532 17 92-70
532 19 29-07
532 18 00-82
532 18 00-65
532 18 77-14
532 18 00-66
532 17 88-07
532 18 40-80
532 17 53-44
532 18 78-57
532 17 98-31
532 19 95-09
873 93 05-00
532 17 86-13
874 76 05-14
532 08 51-79
532 18 01-35
532 18 00-81
532 17 86-95
532 19 77-63
532 17 93-52
532 19 77-64
532 18 40-77
532 18 40-76
872 27 05-05
532 18 92-82
532 18 89-09
532 18 40-75
532 18 25-04
532 19 10-80
532 19 85-41
819 11 15-07
532 19 85-52
874 95 05-12
812 00 00-12
532 17 90-95
532 18 42-06

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

57
6

10
21

4
31
10 21

25
16

18 20

2 6
7

39
55 43

32
33

11
6

8
13

38
41
44

41
34

14
45

35
50
52
51

11
49

48
11

47
47
28

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.
1
2
3

4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

DESCRIPTION

532 18 10-44 Spring, Traction Idler
532 18 05-22 Pulley, Idler (2-1/4)
--Engine, Tecumseh, Model Number
LH195SP (For engine service and
replacement parts, call Tecumseh
Products at 1-800-558-5402)
874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4
532 05 92-89 Washer, Flat
532 16 67-85 Nut, Jam, Lock 5/16-18
532 17 53-30 Pin, Idler Pivot
532 17 90-92 V-Belt, Traction Drive
532 19 85-52 Washer, Lock 5/16
532 19 85-84 Screw, Hex Head 5/16-18 x 1/2
532 17 92-59 Impeller Arm / Pad Assembly
532 08 51-79 Retainer, Hairpin
532 17 88-28 Spring, Brake
532 40 80-10 V-Belt, Impeller Drive
532 15 04-06 Screw, Hex Head 3/8-16 x 1-1/4
532 18 48-04 Arm, Idler
874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2
532 19 85-59 Bushing, Idler Pivot
532 18 05-23 Pulley, Idler (2-3/4)
874 61 05-16 Screw, Hex Head 5/16-18 x 1
532 17 93-71 Spacer, Engine Pulley
532 18 04-78 Pulley, Engine, Traction Drive
532 17 91-57 Pulley, Engine, Impeller Drive
532 40 00-26 Washer, Flat 3/8
532 85 02-63 Washer, Lock, Helical 3/8

KEY PART
NO. NO.
27
28
29
30
31
32
33
34
35
36
37
38
39
41
42
43
44
45
46
47
48
49
50
51
52
55
57
58

DESCRIPTION

532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8
532 15 54-52 Guide, Belt
532 19 22-13 Belt Cover Assembly
(Includes Toolbox Cover)
532 17 88-30 Cover, Toolbox
532 40 05-24 Screw, Hex Head 1/4-20 x 1/2
532 17 92-56 Bolt, Shoulder 5/16-18
532 18 78-53 Bellcrank Shifter
532 19 85-80 Clevis Pin
532 40 54-85 Arm, Auger Control
873 80 05-00 Nut, Lock 5/16-18
532 18 40-86 Bellcrank
532 18 71-01 Link, Speed Control
532 19 21-10 Trunnion, Pivot Bracket
532 70 02-79 Hairpin, Cotter 3/32 x 1/2
532 17 90-65 Pin, Bellcrank
532 18 40-85 Bracket, Bellcrank
817 00 06-16 Screw, Hex Head
532 18 40-74 Pivot Bracket, Impeller Idler Arm
532 18 40-84 Pan, Frame Bottom
871 02 05-12 Screw, Hex Head 5/16-18 x 3/4
532 18 11-56 Nut, Speed 5/16-18
532 40 76-42 Frame Assembly
532 18 80-02 Plate, Frame End
532 40 61-09 Shaft, Auger Control
532 05 70-79 Washer, Hardened
812 00 00-02 Ring, Crescent
811 05 05-00 Washer, Lock, External Tooth 5/16
532 19 85-63 Power Cord

REPAIR PARTS

WHEELS / DECALS

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14
2

4
5

1 10

2
4

5
1 10

REPAIR PARTS

WHEELS / DECALS

SNOW THROWER - MODEL NO. 5224STE (96193001400), PRODUCT NO. 961 93 00-14

KEY PART
NO. NO.

1
2
3
4
5
6

532 18 78-31
532 15 54-43
532 18 78-66
532 14 63-15
532 17 98-30
532 17 46-97

DESCRIPTION

Wheel Assembly, 13", LH
Pin, Klik 1/4
Wheel Assembly, 13", RH
Screw, Hex Head 5/16-18 x 5/8
Bearing, Axle
Washer, Thrust (1")

KEY PART
NO. NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
---

Decal, Danger
Decal, Husqvarna
Decal, Danger, Deflector
Decal, Danger
Decal, Husqvarna, 5524STE
Decal, Instruction
Decal, Traction Lever
Decal, Auger Lever
Decal, Speed Control
Decal, Husqvarna, Crown
Owner’s Manual, English
Owner's Manual, French

532 18 10-38
532 19 13-77
532 18 10-34
532 18 10-41
532 40 58-02
532 18 10-32
532 15 57-98
532 15 58-00
532 18 10-36
532 15 57-94
532 40 57-33
532 40 80-96

532 40 57-33 Rev. 1 08.22.06 BY

Printed in U.S.A.

The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written
in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur,
the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof
of purchase, as explained in section 6, rests solely with the customer.

90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any
Husqvarna product used for commercial, institutional, professional, or income producing purposes or use
except as otherwise provided herein.

The following items are not covered by this warranty:
(1)Normal customer maintenance items which become worn through normal regular use, including, but
not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw
chain, spark plugs, starter ropes and tines;
(2)Natural discoloration of material due to ultraviolet light;
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective
manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer;
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations
which are manufactured by third party engine manufacturer.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component
fails because of a defect in material or workmanship during the warranty period.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY

30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.

HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269
531 83 81-23

2002

To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address
of the selling dealer.

It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly
filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days
from the date of purchase in order to confirm the warranty and to facilitate post-sale service.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION

SECTION 5: CUSTOMER RESPONSIBILITIES

Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase
for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must
be followed as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not
covered under warranty.

Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO
THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE,
AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.

This warranty shall be inapplicable to defects resulting from the following:
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,
corrosion, or any adverse reaction due to incorrect storage or use habits;
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna;
(3)Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable
laws; or:
(4)Additional damage to parts or components due to continued use occurring after any of the above.

SECTION 4: EXCEPTIONS AND LIMITATIONS

1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection
systems used for commercial, institutional, professional or income producing purposes or use.

Emission control system components necessary to comply with CARB-TIER-II and EPA regulations,
except for those components which are part of engine systems manufactured by third party engine manufacturers for which the purchaser has received a separate warranty with product information supplied at
time of purchase.

2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors,
walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld
blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for
noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.

2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area
walks, and ground engaging commercial equipment.

3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)

Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty
Period” of the product as set forth below:
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand
held product.

SECTION 1: LIMITED WARRANTY

WARRANTY STATEMENT

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Modify Date                     : 2006:11:29 10:28:51-05:00
Create Date                     : 2006:08:22 13:16:28-04:00
Page Count                      : 32
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Mod Date                        : 2006:11:29 10:28:51-05:00
Creation Date                   : 2006:08:22 13:16:28-04:00
Author                          : Husqvarna
Metadata Date                   : 2006:11:29 10:28:51-05:00
Title                           : OM, 5524 STE, 96193001400, 2006-08, Snow Thrower
Creator                         : Husqvarna
Page Mode                       : UseOutlines
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools

Husqvarna 5524Ste Users Manual OM, 5524 STE, 96193001400, 2006 08, Snow Thrower

5524STE to the manual a2a4f200-7036-4fb0-a4ec-477f30cdc796

Navigation menu

Versions of this User Manual:

Views

Navigation