Husqvarna Lawn Mower Ez4824 965880401 Users Manual OM, EZ ZERO TURN MOWER, 4824 EC/ K/ 4824/ 5221/ 5224/ 5226/ 6124, 965880201, 965880301, 965880401, 965
2015-01-24
: Husqvarna Husqvarna-Lawn-Mower-Ez4824-965880401-Users-Manual-317620 husqvarna-lawn-mower-ez4824-965880401-users-manual-317620 husqvarna pdf
Open the PDF directly: View PDF .
Page Count: 80
Download | |
Open PDF In Browser | View PDF |
Operator Manual EZ4824EC / 965880201 EZ4824K / 965880301 EZ4824 / 965880401 EZ5221 / 965880501 EZ5224 / 965880601 EZ5226 / 965921601 EZ6124 / 965880701 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English In order to implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs. The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit. ©2008 HTC. All rights reserved. Beatrice, NE. Printed in U.S.A. Contents INTRODUCTION................................................................ 5 Driving and Transport on Public Roads....................... 5 Towing......................................................................... 5 Operating..................................................................... 5 Good Service............................................................... 6 Symbols and Decals.................................................. 7 Safety............................................................................. 9 Safety Instructions....................................................... 9 Personal Safety Equipment....................................... 11 Slope Operation......................................................... 11 Safe Handling of Gasoline......................................... 13 General Maintenance................................................ 14 Transport................................................................... 16 Controls..................................................................... 17 Control Locations....................................................... 17 Steering Control Levers............................................. 18 Parking Brake............................................................ 19 Throttle Control.......................................................... 19 Blade Switch.............................................................. 19 Ignition Switch........................................................... 20 Choke Control............................................................ 20 Fuses......................................................................... 20 Fuel Tank................................................................... 21 Fuel Shut Off Valve.................................................... 22 Cutting Height Adjuster.............................................. 22 Seat Adjustment Lever.............................................. 23 Hour Meter................................................................. 23 Tracking Knob............................................................ 23 Operation.................................................................... 24 Training...................................................................... 24 Steering..................................................................... 24 Before Starting........................................................... 25 Starting the Engine.................................................... 25 Weak Battery............................................................. 28 Jumper Cables................................................ 28 Running..................................................................... 29 Operating On Hills..................................................... 30 Mowing Tips . ............................................................ 31 Stopping the Engine.................................................. 32 Manual Transport....................................................... 33 ZT-2800 Bypass Linkages............................... 33 Pump Release Valves...................................... 33 Maintenance............................................................... 34 Maintenance Schedule.............................................. 34 Battery....................................................................... 36 Ignition System.......................................................... 37 Safety System........................................................... 37 Engine Cooling Air Intake.......................................... 38 Throttle Cable............................................................ 38 Choke Cable.............................................................. 38 Air Filter..................................................................... 39 Briggs & Stratton Engine................................. 39 Kohler Engine.................................................. 40 Kawasaki Engine............................................. 41 Fuel Filter................................................................... 42 Tire Pressures........................................................... 43 Parking Brake............................................................ 43 V-belts........................................................................ 44 Deck Belt Removal.......................................... 44 Pump Belt........................................................ 45 Cutting Blades........................................................... 46 Blade replacement........................................... 46 Adjusting the Mower Deck......................................... 47 Leveling deck................................................... 47 Anti-scalp rollers.............................................. 48 Cleaning.................................................................... 49 Caster Wheels........................................................... 49 Hardware................................................................... 49 LUBRICATION................................................................. 50 Front Wheel Mount.................................................... 51 Front Wheel Bearings................................................ 51 Deck Spindle............................................................. 51 Deck Outer Spindle................................................... 51 Engine Oil.................................................................. 52 Engine Oil Levels............................................. 52 Changing the Engine Oil.................................. 53 *Transaxle (Transmission) Fluid Change................... 54 Hydraulic Pump Fluid Change................................... 55 Purging Procedures......................................... 56 TROUBLESHOOTING..................................................... 57 STORAGE........................................................................ 59 Winter Storage........................................................... 59 Service....................................................................... 59 schematics.................................................................. 60 TECHNICAL DATA........................................................... 61 Accessories............................................................... 61 Torque Specifications................................................ 61 CONFORMITY CERTIFICATES...................................... 68 SERVICE JOURNAL........................................................ 70 English-3 WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING! Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. English-4 INTRODUCTION Congratulations Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance. This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance) by all who operate this machine is important for the safety of the operator and others. It can also considerably increase the life span of the machine and increase its resale value. If you sell your machine, be sure to give the operator’s manual to the new owner. The final chapter of this operator’s manual provides a Service Journal. Ensure that service and repair work are documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information. Take the operator’s manual along when the machine is taken to your dealer for service. General In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction. Continuous dedication to improve our products require that specifications and design are subject to change without notice. Driving and Transport on Public Roads Check applicable road traffic regulations before transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways. Towing If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on the towed equipment. Make wide turns to avoid jack-knifing. Travel slowly and allow extra distance to stop. Do not tow on sloped ground. The weight of the towed equipment may cause loss of traction and loss of control. Follow the manufacturer's recommendation for weight limits for towed equipment. Do not tow near ditches, canals, and other hazards. Operating This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones, tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed. Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense. The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to maintain this machine. Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail. Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage. Husqvarna-5 INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator’s manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional: This Operator’s Manual belongs to the machine with the manufacturing number: Engine Transmission Manufacturing Number The machine’s manufacturing number can be found on the printed plate affixed to the right in the engine compartment. Stated on the plate, from the top are: The machine’s type designation (I.D.). The manufacturer’s type number (Model). The machine’s serial number (Serial no.) Please have the type designation and serial number available when ordering spare parts. The engine’s manufacturing number is stamped on one of the valve covers. The plate states: The engine’s model. The engine’s type. Code Please have these available when ordering spare parts. The wheel motors and hydrostatic pumps have a barcode decal affixed at the rear. 6-Husqvarna symbols and decals These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. WARNING! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual. IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly. R N Reverse Neutral Fast Warning! Parking Brake CE conformity marking. Only for European market Battery acid is corrosive, explosive and flammable Use protective glasses Slow Choke Fuel Warning! Rotating blades, keep away from the discharge deck Do not touch parts Do not stand here Use protective gloves Noise emissions to the surroundings in accordance with the European Union’s directive. The machine’s emission is stated in the chapter TECHNICAL DATA and on the decals. Only machines for European market Husqvarna-7 symbols and decals Read Operator’s Manual Shut off engine and remove key before performing any maintenance or repair work Whole body Severing of fingers exposure to and toes thrown objects 8-Husqvarna Moving sharp blades under cover Keep a safe distance from the machine Use on slopes no greater than 10° No passengers Do not open or remove safety shields while engine is running Careful backing up, watch for other people Careful going forward, watch for other people SAFETY Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. It concerns your safety. IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades. • Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area. • Never carry passengers. The machine is only intended for use by one person. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. • Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces. • Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working • Slow down before turning. • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. • Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard. • Operate machine only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. 8011-512 Read the operator’s manual before starting the machine Clear the area of objects before mowing 8011-513 Husqvarna-9 SAFETY • • • • • • • • • Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Always wear eye protection when operating machine. Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. Follow the manufacturer’s recommendation for wheel weights or counterweights. Anyone who operates this machine must first read and understand this Operation Manual. Local laws may regulate the age of the user. Keep machine free of grass, leaves or other debris buildup which can touch the hot exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris, causing buildup to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage. 10-Husqvarna Never take passengers 8011-520 WARNING! WARNING! This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine's system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces. SAFETY Personal Safety Equipment WARNING! When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment. • • • • • • • Make sure that you have first aid equipment close at hand when using the machine. Never use the machine when barefoot. Always wear protective shoes or boots, preferably with steel toe caps. Always wear approved protective glasses or a full visor when assembling or driving. Always wear gloves when handling the blades. Never wear loose clothing that can get caught in moving parts. Use ear protectors to avoid damage to hearing. Slope Operation Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes (10 degrees maximum), not across. • Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Choose a low ground speed so that you will not have to stop while on the slope. • Do not mow on wet grass. Tires may lose traction. • Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope. • Keep movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause machine to roll over. • Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine. • Do not use on steep slopes. • Do not try to stabilize the machine by putting a foot on the ground. • Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in. Personal protective equipment Mow up and down, not side to side 8011-670a 6003-004 WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across any slopes. Husqvarna-11 SAFETY Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area. • Before and while backing, look behind and down for small children. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. • Never allow children to operate the machine. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child. Be extra cautious when driving on slopes Never allow children to operate the machine Keep children away from work area 12-Husqvarna 8011-509 8011-517 8011-518 SAFETY WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. Safe Handling of Gasoline To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container. • Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling. • Never fuel the machine indoors. • Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliance. • Before you begin refueling, minimize the risk of static electricity by touching a metal surface. • Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from the vehicle when filling. • Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and tighten securely. • Do not start the engine near spilled fuel. • Never use gasoline as a cleaning agent. • If leaks arise in fuel system, engine must not be started until problem has been resolved. • Check the fuel level before each use and leave space for the fuel to expand, as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow. 8011-516 Never fill the fuel tank indoors WARNING! The engine and the exhaust system become very hot during operation. There is risk for burns if touched. Allow engine and exhaust system to cool at least two (2) minutes before refueling. Husqvarna-13 SAFETY General Maintenance • • • • • • • • • • • • • • • • • Never operate machine in a closed area. Keep all nuts and bolts tight to be sure the equipment is in safe working condition. Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing. If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting. Never make any adjustments or repairs with the engine running. Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary. Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. Check brake operation frequently. Adjust and service as required. Maintain or replace safety and instruction labels, as necessary. Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices. Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components. Be very careful when handling battery acid. Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water. Acid in the eyes can cause blindness, contact a doctor immediately. Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks. The battery can explode and cause serious injury/ damage. Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition. 14-Husqvarna Never drive the machine in an enclosed space 8011-515 WARNING! Use protective glasses for maintenance work. WARNING! The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery. SAFETY • • • • • Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery. Use protective goggles. Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel. Never work with the starter circuit if there is spilled fuel. Disconnect the chassis cable from the battery first and reconnect it last. 6003-009 WARNING! Avoid electrical sparking and its consequences by the following routines: • • • • • • • • • • Do not make a bridge short circuit across the starter relay to run the starter. Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas. Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. Never make adjustments with the engine running. The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine. The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. Check the parking brake’s functionality regularly. Adjust and service as necessary. The mulch blades should only be used in familiar areas when higher quality mowing is desired. Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine. Allow the machine to cool before putting it in storage. Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water. Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage. Risk of sparking 8009-728 Husqvarna-15 SAFETY Transport • • • • • • • The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer. Use an approved trailer to transport the machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting. Do not operate this machine on public roadways. Check and abide by local traffic regulations before transporting the machine on any road. Do not tow this machine, it may cause damage to the drive system. Do not tow with this mower. They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator. Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed. Do not lift! The machine is not intended to be lifted by hand. IMPORTANT INFORMATION The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over. 16-Husqvarna Regularly clean deck 8011-514 WARNING! Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately. CONTROLS This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with either a Kohler or Briggs & Stratton four-stroke overhead valve engine developing 24-26 horse power*. Transmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed. Control Locations 2 12 7 1 9 11 8 1. 2. 3. 4. 5. 6. 7. 4 5 3 Steering control levers Parking brake Throttle control Blade switch Ignition switch Choke control Fuses 6 12 10 8. Fuel tank cap 9. Fuel shut off valve 10. Deck lift 11. Seat adjustment lever 12. Hour meter 13. Tracking adjustment *As rated by the engine manufacturer. Husqvarna-17 CONTROLS Steering Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward. When both controls are in the neutral position (N), the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively. In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right. Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver. If the steering controls are in uneven positions when standing still or do not fit in the slots for moving the controls outward, they can be adjusted. 8058-022 Steering controls WARNING! The machine can turn very rapidly if one steering control is moved much further forward than the other. 1 2 3 4 1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Motion control lever, right side 18-Husqvarna 8011-7912a CONTROLS Parking Brake IMPORTANT INFORMATION The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower. The parking brake is found on the left of the machine. Push button and pull the lever backward to activate the brake and push button and push forward to release it. 8058-020 Parking brake released Throttle Control The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower Deck. In order to increase or decrease the engine speed, the control is moved forward or back respectively. Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs. USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging. ST FA UP BLADES ON CHOKE OW SL DOWN BLADES OFF 8052-001 Throttle control Blade Switch In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed. ST FA UP BLADES ON CHOKE OW SL Blade switch DOWN BLADES OFF 8052-001 Husqvarna-19 CONTROLS Ignition Switch The ignition key is placed on the control panel and is used to start and stop the engine. ST FA UP BLADES ON CHOKE OW SL DOWN BLADES OFF 8052-001 Ignition switch Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixture. For cold starts the control should be pulled out. ST FA UP BLADES ON CHOKE OW SL Choke control DOWN BLADES OFF 8052-001 Fuses Fuses are located under the seat of the machine. They are accessed by tilting the seat forward. They are flat pin fuses of the same type used in automobiles. There are two fuses with ratings and functions: 20 Amp Primary fuse 7.5 Amp Mower deck coupling 20-Husqvarna Fuses 8011-420 CONTROLS Fuel Tank Read the safety instructions before refueling. The machine has one fuel tank, just behind the seat. The tank capacity is 4 gallons (15.1 liters). Regularly check the gas cap gasket for damage and keep the cap properly tightened. The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel. Damage to engine and components may occur. WARNING! Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety instruction). WARNING! The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool at least two (2) minutes before refueling. WARNING! Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. Fuel tank 8058-021 IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur. When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to insure good cold weather starting. Husqvarna-21 CONTROLS Fuel Shut Off Valve The fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned perpendicular to the fuel line. Fuel shut off valve in the CLOSED position 8011-419 Cutting Height Adjuster The deck cutting height is obtained by pressing the button and moving the lever forward to the correct cutting height on the cutting plate. The cutting height range is from 1½" (38mm) to 4" (102mm) in ½ (13mm) increments. The heights are measured from the ground up to the blade tip with the engine not running. IMPORTANT INFORMATION In order to obtain an even cutting height, it is important that the air pressure in all tires is 15 psi / 103 kPa / 1 bar. The mower deck’s lifting lever IMPORTANT INFORMATION Always raise the deck to the highest position for transport. 22-Husqvarna 8058-019 CONTROLS Seat Adjustment Lever The seat can be adjusted lengthways. When making adjustments, the lever under the right front side of the seat is pulled to the side, after which the seat can be moved backward or forward. 8058-034 Lengthways adjustment Hour Meter The hour meter displays the total operating time. It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter cannot be manually reset. ST FA UP BLADES ON CHOKE OW SL Hour meter DOWN BLADES OFF 8052-001 Tracking Knob If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (103 kPa / 1 bar) for all tires. Tracking must be checked on a flat and level concrete or blacktop surface. Rotating the tracking knob allows fine tuning adjustments so the machine tracks straight with the steering control levers in the full forward position. Rotate the knob clockwise (as viewed from the operation position) to increase the speed on the left lever. Rotate counterclockwise to decrease speed. Tracking knob 8058-020 Husqvarna-23 operation Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine. Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities. We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power. Additionally, we suggest when first operating the mower, use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until operator becomes comfortable with controls. We also suggest first time users, or new users to Zero Turn mowers to become familiar with the mower’s movement on a hard surface, such as concrete or blacktop PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability, they may damage turf due to overly aggressive maneuvers. IMPORTANT INFORMATION When control levers are in the reverse position they return to neutral when released. This may cause the mower to suddenly stop. Steering To move forward and backward The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel. First time users should push mower (see “Moving by Hand” in the Operation section) to an open, flat area, without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must be in the seat, start engine (see “Before Starting” in Operation section), adjust engine speed to idle, disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as the control levers have not been moved forward or backwards, mower will not move. Slowly move both control levers forward slightly. This will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving backwards. Push forward on control levers to the neutral position and mower should stop moving. To turn to the right While moving in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that direction. To turn to the left While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that direction. To zero turn While moving in a forward direction, first pull both control levers back until the mower stops or slows dramatically. Then by alternating one lever slightly to the forward position and the other in the reverse position. 24-Husqvarna operation Before Starting • Read the sections Safety Instructions and Controls before starting the machine. • Perform the daily maintenance before starting (see Maintenance Schedule in the Maintenance section). • Check that there is sufficient fuel in the fuel tank. • Adjust the seat to the desired position. The following conditions must be fulfilled before the engine can be started: • The blade switch for engaging the mower blades must be depressed. • The parking brake must be on. • Both steering controls must be in the locked (outer) neutral position. Starting the Engine • • • Set mower deck to transport position 8058-019 Sit on the seat. Raise the mower deck by pushing the release button on the top of the lifting lever. Pull the lifting lever backward to the locked position (transport) position. Activate the parking brake by pushing the release button in and pulling the lever fully upwards. Pull parking brake upwards to activate. 8058-020 Disengage the mower blades by pressing the blade switch downwards. ST FA UP BLADES ON CHOKE OW SL Depress blade switch DOWN BLADES OFF 8052-001 Husqvarna-25 operation Move the steering controls outward to the locked (outer) neutral position. 8061-026 Place controls in neutral position Move the throttle to the middle position. ST FA UP BLADES ON CHOKE OW SL DOWN BLADES OFF 8052-001 Set the throttle If the engine is cold, the choke control should be pulled up. ST FA UP BLADES ON CHOKE OW SL 26-Husqvarna Set the choke control DOWN BLADES OFF 8052-001 operation Press in and turn the ignition key to the start position. STOP 8050-780 Turn to the start position When the engine starts, immediately release the ignition key back to the run position. IMPORTANT INFORMATION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying. Set the desired engine speed with the throttle. Allow the engine to run at a moderate speed, “half throttle” for 3-5 minutes before loading it too heavily. USE FULL THROTTLE WHEN MOWING (no choke). STOP WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces. 8050-781 Return to run position ST FA UP BLADES ON CHOKE OW SL Set the engine speed DOWN BLADES OFF 8056-001 Husqvarna-27 operation Weak Battery WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. IMPORTANT INFORMATION Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles. If your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance Section.) If “jumper cables” are used for emergency starting, follow this procedure: Jumper Cables • Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis. • Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery. • Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery. To remove cables, reverse order • Remove BLACK cable first from chassis and then from the fully charged battery. • Remove RED cable last from both batteries. 28-Husqvarna Jumper cable connection 8011-642 operation Running 1. Release the parking brake by pushing the button and moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 2. Move the steering controls to the neutral position (N). Parking brake released 8058-020 3. Set retaining pin into selected cutting height and secure the opposite side with a cotter hairpin. WARNING! Ensure that no one is near mower when engaging blade switch. Make sure the work area is free from objects that could be thrown by the rotating blades. Secure selected cutting height 8058-024 4. Push the release button on the cutting height lever and move lever to the pin, release the button. 5. Set the cutting height with the cutting height adjustment lever. Mower deck lifting lever 8058-019 Husqvarna-29 operation 6. Engage the mower deck by pulling out the blade switch. 7. Move throttle control to full throttle. The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively. In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right. Turning on the spot (zero turn) can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. ST FA UP BLADES ON CHOKE OW SL DOWN BLADES OFF Set blade engagement and throttle control 8052-001 Operating On Hills Read the Safety Instructions “Driving on Slopes” in the “Safety Instructions”. WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes. • • • The slowest speed possible should be used before starting up or down hills. Avoid stopping or changing speed on hills. If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake. Place controls in neutral position 8061-026 IMPORTANT INFORMATION Control levers return to neutral when released. This may cause the mower to suddenly stop. • • • To restart movement, release the parking brake. Pull the control levers back to the center of the mower and press forward to regain forward motion. Make all turns slowly. Parking brake released 30-Husqvarna 8058-020 operation Mowing Tips • • • • • • • • Observe and flag rocks and other fixed objects to avoid collisions. Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For healthier and better looking lawns, mow often after moderate growth. For best cutting performance, grass over 6" (15 cm) in height should be mowed twice. Make the first cut relatively high, the second to the desired height. The mowing result will be best with a high engine speed (the blades rotate rapidly) and low speed (the rider moves slowly). If the grass is not too long and dense, the driving speed can be increased without negatively affecting the mowing result. The finest lawns are obtained by mowing often. The lawn becomes more even and the grass clippings more evenly distributed over the mown area. The total time taken is not increased as a higher operating speed can be used without poor mowing results. Avoid mowing wet lawns. The mowing result is poorer because the wheels sink into the soft lawn, clumps build, and the grass clippings fasten under the cowling. Hose the mower deck underside with water after each use. When cleaning, the mower deck shall be raised into the transport position. Make sure the mower is cooled and the engine is off. Use compressed air to clean top surface of the deck. Avoid flooding water on top surface, engine and electrical components. When the mulching kit is used, it is important that the mowing interval is frequent. WARNING! Clear the lawn of stones and other objects that can be thrown out by the blades. Mowing pattern 8011-603 WARNING! Never drive the rider on terrain that slopes more than 10 degrees. Mow slopes up and down, never side to side. Avoid sudden directional changes. Husqvarna-31 operation Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling. • Disengage the mower deck by depressing the blade switch. ST FA UP BLADES ON CHOKE OW SL DOWN BLADES OFF 8052-001 Disengage the mower deck and move throttle to minimum • • • Raise the mower deck by pressing the button on the lever and pullng backward to the transport position. When the machine is standing still, activate the parking brake by pushing the lever button and pulling the lever upward. Move the throttle to the minimum position (tortoise symbol). Turn the ignition key to the stop position. The mower deck’s lifting lever • • 8058-019 Move the steering controls outward. Remove key. Always remove key when leaving the mower to prevent unauthorized use. IMPORTANT INFORMATION Leaving the ignition switch in any other position than “OFF” will cause the battery to be discharged. Place controls in neutral position 32-Husqvarna 8061-026 operation Manual Transport ZT-2800 Bypass Linkages When pushing or pulling the mower, engage the ZT-2800 (Integrated Zeroturn Transaxle) bypass linkages. The ZT-2800 bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck into the highest cutting position. 2. Pull the ZT-2800 bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position. 3. To reengage the ZT-2800 to drive, reverse the above procedure. Load the machine into truck or trailer by driving up ramps in low gear. DO NOT LIFT! The machine is not intended to be lifted by hand. 8058-032 Bypass linkage, ZT-2800 engaged WARNING! Make no adjustments without: • the engine stopped, • the ignition key removed, • the parking brake activated Pump Release Valves Pump release valves are located at the left and right of the pump. They are used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pump. The left bypass valve sits directly opposite the right valve. It is not visible in the illustration. Use a 17 mm open end wrench or socket and ratchet. Turn the outer locknut 2-3 turns. Using an 8mm wrench or socket, turn the inner nut one turn. Reverse the procedure to reset the pump, makng sure the outer locknut is tightened. Bypass linkage, ZT-2800 locked in the bypass position 8058-032 IMPORTANT INFORMATION Tighten the valve moderately. Do not overtighten the valve when closing. That can damage the valve seat. Pump release valve - right 8011-507 Husqvarna-33 MAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation. Read “Maintenance” in the Safety Instructions section. 1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. 2) In dusty conditions, cleaning and replacement are required more often. 3) For daily use, the machine should be lubricated twice weekly. 4) Performed by authorized service workshop. ● = Described in this manual ♦ = Not described in this manual Daily Maintenance Check the parking brake Check the engine’s oil level (every refueling) Check the safety system Check for fuel and oil leakages Check/clean the engine’s cooling air intake Check the mower deck Check for loose hardware (screws, nuts) Clean under the mower deck Start the engine and blades, listen for unusual sounds Check for damage Thoroughly clean around the engine Clean around belts, belt pulleys Before ● ● ● ♦ Weekly After At Maintenance interval least in hours once each 50 100 300 year 25 ● ● ● ● ♦ ♦ ♦ ♦ Check the tire pressures Check battery Sharpen/Replace mower blades Clean the engine’s cooling air intake 2) Clean the air cleaner’s pre-filter 2) (foam) Clean the air cleaner’s filter cartridge 2) (paper filter) Check/adjust the parking brake Inspect muffler/Spark arrester 34-Husqvarna ● ● ● ♦ ♦ ● ● ● ● ● ● ♦ ♦ MAINTENANCE Daily Maintenance Before After Weekly At Maintenance interval least in hours once each 50 100 300 year 25 Check/adjust throttle cable Check the condition of belts, belt pulleys Change the engine oil 1) Replace the engine oil filter Clean/replace the spark plugs Replace the fuel filter Replace the air filter (paper filter) 2) ● ● ● ● ● ● ● Check the caster wheels (every 200 hours) Replace the air cleaner’s pre-filter 2) (foam) Check/adjust the mower deck Check the engine valve clearance Perform the 300-hour service 3) 1) 3) ● ● ♦ ♦ First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. conditions, cleaning and replacement are required more often. 3) Performed by authorized service workshop. ● ♦ ● ● ● ● ● ● ● ● ♦ ♦ 2) In dusty = Described in this manual = Not described in this manual WARNING! Before performing any service or adjustment checklist • Engage the parking brake. • Place the Blade-switch in the disengaged position. • Turn the ignition switch to “OFF” position and remove the key. • Make sure the blades and all moving parts have completely stopped. • Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug. Husqvarna-35 MAINTENANCE Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • See chart for charging times STANDARD STATE BATTERY OF CHARGE APPROXIMATE BATTERY CHARGING TIME* TO FULL CHARGE AT 80OF / 27OC Maximum Rate at: 50 Amps 30 Amps 20 Amps 10 Amps 12.6V 100% 12.4V 75% 20 min. 35 min. 48 min. 90 min. 12.2V 50% 45 min. 75 min. 95 min. 180 min. 12.0V 25% 65 min. 115 min. 145 min. 280 min. 11.8V 0% 85 min. 150 min. 195 min. 370 min. - FULL CHARGE - *Charging time depends on battery capacity, condition, age, temperature and efficiency of charger WARNING! IMPORTANT INFORMATION Always wear eye protection when around batteries. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. Always use two wrenches for the terminal screws. Cleaning battery and terminals Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. 1. Move terminal covers. 2. Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine. 3. Rinse the battery with plain water and dry. 4. Clean terminals and battery cable ends with wire brush until shiny. 5. Coat terminals with grease or petroleum jelly 6. Reinstall battery. Replacing battery 1. Lift seat and rotate forward. 2. Using two ½” wrenches disconnect BLACK battery cable then RED battery cable. 3. Position deck to lowest setting. 4. Front underside of frame, remove the nuts that secure the battery hold-down. 5. Carefully remove the battery from the mower. 6. Install new battery with terminals in the same position as the old battery. 7. Reinstall battery hold-down and secure with nuts removed in Step 4. 8. Reconnect RED battery cable to positive (+) battery terminal with hex bolt and hex nut. 9. Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and nut 10. Replace terminal boot cover. 11. Lower seat 36-Husqvarna WARNING! Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparks from accidental grounding. Remove battery hold-down to replace battery 8050-109 MAINTENANCE Ignition System The engine is equipped with an electronic ignition system. Only the spark plugs require maintenance. For recommended spark plugs, see Technical Data. 1. Remove the ignition cable boot and clean around the spark plug. 2. Remove the spark plug with a spark plug socket wrench. 3. Check the spark plug. Replace the spark plug if fouled, the electrodes are burned and if the insulation is cracked or damaged. Clean the spark plug with a steel brush if it is to be reused. 4. Measure the electrode gap with a gapping tool. The gap should be .030" (0.75 mm). Adjust as necessary by bending the side electrode. 5. Reinsert the spark plug, turning by hand to avoid damaging the threads. 6. After the spark plug is seated, tighten it using a spark plug wrench so that the washer is compressed. A used spark plug should be turned 1 /8 of a turn from the seated position. A new spark plug should be turned a ¼ turn from the seated position. 7. Replace the ignition cable. IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine. Inadequately tightened spark plugs can cause overheating and damage the engine. Tightening the spark plugs too hard can damage the threads in the cylinder head. Measure the electrode gap 8011-054 Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: 1. The mower deck is disengaged. 2. The steering controls are in the outer, locked neutral position. 3. The parking brake is on. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again. If the machine starts when one of these conditions is not met, turn the machine off and repair the safety system before using the machine again. Make sure the engine stops when the park brake is not engaged and the operator leaves the seated position. Check that the engine stops if the mower blades are engaged and the driver temporarily moves off the drivers seat. Steering controls locked in neutral 8058-026 IMPORTANT INFORMATION In order to be able to drive, the driver must sit in the seat and release the parking brake before the steering controls can be moved into the neutral position, otherwise the engine will stop. Husqvarna-37 MAINTENANCE Engine Cooling Air Intake Check that the engine’s cooling air intake is free from leaves, grass, and dirt. If the cooling air intake is clogged, engine cooling deteriorates, which can lead to engine damage. The cooling air intakes rotates when the engine is running. Keep fingers away. Check and clean the cooling air intake 8061-014 Throttle Cable Check that the engine responds to throttle increases and that a good engine speed is attained at full throttle. If doubts arise, contact the service workshop. If adjustments are necessary, they can be made as follows for the lower cable: 1. Loosen the clamping screw for the cable’s outer casing and move the throttle to the full throttle position. 2. Check that the throttle cable is mounted in the correct hole in the lower lever, see illustration. 3. Push the throttle cable’s outer casting as far to the right as possible and tighten the clamping screw. Adjusting the throttle cable 8011-605 Choke Cable If the engine produces black smoke or is difficuIt to start, this can be because the choke cable is incorrectly adjusted (upper cable). If doubts arise, contact the service workshop. If adjustments are necessary, they can be made as follows: 1. Loosen the clamping screw for the cable’s outer casing and push the choke control fully in. 2. Check that the choke cable is mounted in the upper lever, see illustration. Push the choke cable’s outer casing as far to the left as possible and tighten the clamping screw. Adjusting the choke cable 38-Husqvarna 8011-605 maintenance Air Filter Briggs & Stratton Engine 1. Loosen screws and remove air filter cover. 2. Remove the filter cartridge by pulling upwards along the outside edge. WARNING! The engine and the exhaust system become very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool at least two (2) minutes. Loosen cover screws 8009-406 3. Remove the foam filter (precleaner). Clean the foam filter with mild detergent and water. Squeeze dry in a clean cloth. Do not oil the foam sleeve. 4. Tap the paper filter against a fixed surface to remove dust. If the paper filter is still dirty, it must be replaced. 5. Wipe clean the inside of air filter housing. 6. Refit the foam filter (pre filter). IMPORTANT INFORMATION Do not use compressed air to clean the air filter. Do not wash the paper filter. Do not oil the paper filter. Remove filter 8019-014 7. Mount the filter in the air filter housing. 8. Replace the cover over the air filter housing and secure with screws. IMPORTANT INFORMATION Operating the engine with loose or damaged air cleaner components could allow unfiltered air into the engine causing premature wear and failure. Reinstall filter 8019-015 Husqvarna-39 maintenance Kohler Engine These engines are equipped with a replaceable, high density paper air cleaner element. Some engines are also equipped with an oiled, foam precleaner surrounding the paper element. Check the air cleaner daily or before starting the engine. Check for a buildup of dirt and debris around the air cleaner system. Keep this area clean. Also check for loose or damaged components. Replace all bent or damaged air cleaner components. Servicing Precleaner If so equipped, wash and re-oil the precleaner every 25 hours of operation (more often under extremely dusty or dirty conditions). Replace the precleaner annually, or every 100 hours. 1. Open the door on the blower housing to access the air cleaner element and precleaner. 2. Unhook the latch and remove the air cleaner element assembly for servicing. Make sure the base and the sealing areas are clean before reassembly. 3. Wash the precleaner in warm water with detergent. Rinse the precleaner thoroughly until all traces of detergent are eliminated. Squeeze out excess water (do not wring). Allow the precleaner to air dry. 4. Saturate the precleaner with new engine oil. Squeeze out all excess oil. Servicing Paper Element Check the paper element every 50 hours of operation, (more often under extremely dusty or dirty conditions). Clean or replace the element as necessary. Replace the air cleaner element annually, or every 100 hours. 1. Remove the precleaner (if so equipped) from the paper element. 2. Gently tap the paper element to dislodge dirt. Do not wash the paper element or use pressurized air, as this will damage the element. Replace a dirty, bent, or damaged element with a new one. Handle the new element carefully; do not use if the sealing surfaces are bent or damaged. 3. Clean the air cleaner base as required and check condition. 4. Reinstall the precleaner (if equipped) over the paper air cleaner element and install on the base. Secure with the latch. 5. Close and latch the door. 40-Husqvarna IMPORTANT INFORMATION Operating the engine with loose or damaged air cleaner components could allow unfiltered air into the engine causing premature wear and failure. 1 4 3 1. Air cleaner access door 2. Air cleaner element 3. Latch 4. Precleaner (on some models) Air filter cleaning and replacement Unlatch and remove element 2 8058-028 8058-029 MAINTENANCE Kawasaki Engine 1. Remove the plastic fastener on the top of the air filter cowling and remove the air filter cowling. WARNING! The engine and the exhaust system become very hot during operation. There is a risk for burns if touched. Allow engine and exhaust system to cool at least two (2) minutes. Remove the air filter cowling 8011-768 2. Remove the foam rubber pre-filter and clean using a mild detergent. Squeeze it dry with a clean cloth. Remove pre-filter 8011-557 3. Remove the wing nuts for the air filter and remove the paper filter. IMPORTANT INFORMATION Do not use compressed air to clean the air filter. Do not wash the paper filter. Do not oil the paper filter. Remove paper filter 8011-558 Husqvarna-41 MAINTENANCE 4. Tap the paper filter against a fixed surface to remove dust. If the paper filter is still dirty, it must be replaced. To refit filter: 1. Check that the seal on the bottom of the paper filter is whole. 2. Mount the paper filter in the air filter housing and tighten the wing nuts. 3. Refit the pre-filter on the paper filter. 4. Replace the cowling over the air filter housing. Do not over tighten the plastic fastener. Remove dust 8009-181 Fuel Filter Replace the line-mounted fuel filter every 100 hours (once per season) or more regularly if it is clogged. 1. Replace the filter as follows: 2. Move the hose clamps away from the filter. Use flat-nosed pliers. 3. Pull the filter loose from the hose ends. 4. Push the new filter into the hose ends. Position the filter with the “FLOW” arrow pointing up toward the fuel pump. If necessary, a soap solution can be applied to the filter ends to ease mounting. 5. Move the hose clamps back toward the filter. Fuel filter 8011-468 Fuel Pump Air Filter Regularly check that the fuel pump’s air filter is free from dirt. Remove the screws and open the pump, no hoses need be removed. The filter can be cleaned with a brush if necessary. Replace the filter on the console. Fuel pump air filter 42-Husqvarna 8009-147 MAINTENANCE Tire Pressures All tires should be at 15 psi / 103 kPa / 1 bar. 8011-564 Check tire pressures Parking Brake Visually check that no damage is found on the lever, cables, or switch belonging to the parking brake. Perform a standstill test and check that there is sufficient braking action. To adjust the parking brake, contact the Husqvarna service workshop. IMPORTANT INFORMATION The machine must be absolutely standing still when applying the parking brake. 8058-020 Parking brake WARNING! Faulty adjustment will result in reduced braking ability and can cause an accident. Husqvarna-43 MAINTENANCE V-belts Idler arm Check every 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal operation. The belts are not adjustable. Replace belts if they begin to slip from wear. Deck Belt Removal 1. Park on a level surface. Apply parking brake. 2. Lower the deck into the lowest cutting position. 3. Remove bolts from belt shields and remove shields. 4. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface. 5. Remove tension on the belt by moving the idler arm. 6. Carefully slip belt up over the top of the cutter housing pulleys and remove belt. Rolling belt over the pulleys may damage the belt. Deck Belt Installation NOTE: For ease in installing the deck belt, refer to the routing decal on the top of the deck. 1. Wrap the deck belt around the electric clutch pulley that is located on the engine shaft. 2. Route the belt forward and up onto the deck. 3. Place belt around spring loaded idler pulley. 4. Wrap the belt around the stationary idler pulley and around the mandrel housings. 5. Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt. 6. Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed. 7. Replace belt shields on both mandrel housings and secure with fasteners. 44-Husqvarna Belt Shields Removing deck belt 1 2 1. Clutch pulley 2. Deck belt Belt routing, deck belt 8011-764 MAINTENANCE Pump Belt Replacing pump belt Park the mower on a level surface. Engage the parking brake. Belt removal 1. Remove the deck belt (see Deck Belt Removal in this section of the manual). 2. Create slack in the belt by removing the spring on the pump idler arm. 3. The belt should now be able to be removed from the engine pulley and pump pulleys. Belt installation 1. Wrap the belt around the pulley 2. Route the belt around the inside of the idler pulley. 3. Wrap the belt around the engine pulley. 4. Reattach the spring on the pump idler arm. 5. Reinstall the deck belt. (see Deck Belt Installation in this section of the manual). 1 2 3 1. Electric clutch 2. Idler spring 3. Clutch stop Pump belt removal 8054-002 Husqvarna-45 MAINTENANCE Cutting Blades In order to attain the best mowing effect, it is important that the blades are well sharpened and not damaged. Bent or cracked blades or blades with large nicks should be replaced. IMPORTANT INFORMATION The sharpening of blades should be carried out by an authorized service workshop. Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the service workshop decide whether the blade can be repaired/ ground or must be replaced. Balance the blades after sharpening. Check the blade mounts. 8011-604-1 Check the blades WARNING! Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling. Blade replacement 1. Remove blade bolt by turning counterclockwise. 2. Install new or resharpened blade with stamped “GRASS SIDE” facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing. 3. Install and tighten blade bolt securely. 4. Torque blade bolt to 90 ft/lbs (122 Nm). 3 1 IMPORTANT INFORMATION Special blade bolt is heat treated. 2 Replace with a Husqvarna bolt if required. Do not use lower grade hardware than specified. 1. Blade 2. Blade bolt (special) 3. Cutter housing Blade attachment 46-Husqvarna MAINTENANCE Adjusting the Mower Deck Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See “Technical Data” under Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. The deck should be adjusted slightly higher in the rear. NOTE:To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves. Turn each outer blade tip to align with the deck or in a side-to-side manner. 2. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck. Retain this measurement. 3. Move to the opposite side, check that measurement is the same. If adjustment is required—with a ¾" or adjustable wrench, turn the lift link adjustment nuts on either side counterwise to lower or clockwise to raise. Adjust until both side-to-side measurements are equal. Lift link adjustment nut 8058-030 4. Turn any blade to align with the deck in frontto-rear manner. If the rear blade tip does not measure 1/8" to ½" higher, follow the front adjustment instructions that follow. 5. With a 5/8 or adjustable wrench, turn the nuts on the front suspension linkage. Clockwise raises the front of the mower, counter clockwise will lower the front. Adjust nuts until rear of mower deck is positioned level to 1/8" higher in the rear than the side-to-side measurement. NOTE: This will place the mower deck in a base measurement position. Additional adjustment may be required to achieve desired cut for the type of grass or conditions being mowed. Deck front adjustment nuts 8058-031 Husqvarna-47 MAINTENANCE Anti-scalp rollers Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Anti-scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions. IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface. The anti-scalp rollers can be set in three positions: • Upper position 1½ to 2½" (38 to 64 mm) grass • Middle position 2½" to 4" (64 to 102 mm) grass • Lower position 4" to 6" (102 to 128 mm) grass. The rollers should be approximately ¼" (6.5 mm) from ground. Do not adjust the rollers to support the deck. IMPORTANT INFORMATION The anti-scalp rollers must not be used for gauge wheels or the roller and deck may be damaged. 48-Husqvarna Anti-scalp rollers 8050-830 MAINTENANCE Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the dirt sticks. Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck. Regularly clean deck and underside of the deck with normal water pressure. Do not use a high pressure washer or steam cleaner. Avoid spraying engine and electrical components with water Do not rinse hot surfaces with cold water. Let unit cool before washing. IMPORTANT INFORMATION 8050-831 Clean regularly Use protective glasses when cleaning and washing. Caster Wheels Check every 200 hours. Check that wheels rotates freely. If wheels do not rotate freely take the unit to your dealer for service. Foam filled tires or solid tires will void the warranty. 2 IMPORTANT INFORMATION DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures. Only use O.E.M. specified tires. Removal and installation of caster wheel Remove nut and caster bolt. Pull the wheel out of the yoke and take care of spacers. Install in reverse order. Tighten caster bolt. Hardware 1 4 3 1. Caster yoke 2. Caster bolt 3. Caster long spacer 4. Caster small spacers (not on all models) Caster wheels 8011-619-4 Check daily. Inspect the entire machine for loose or missing hardware. Husqvarna-49 LUBRICATION 1 2 3 4 6 5 * 8050-832 12/12 Every year Lubricate with grease gun 1/52 Every Week Oil change 1/365 Every day Lubricate with oil can Level check Filter change * Change transmission filter General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease. For daily use, the machine should be lubricated twice weekly. 50-Husqvarna Wipe away excess grease after lubrication. It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts. LUBRICATION Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out. Use only good quality bearing grease. Grease from well-known brand names (petrochemical companies) usually maintains a good quality. Front Wheel Bearings Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out. Use only good quality bearing grease. IMPORTANT INFORMATION Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces. Lubricating the front wheels 8011-731 Deck Spindle Lower the cutting deck completely. If a grease gun without a rubber hose is used, the foot plate must be removed. Lubricate with a grease gun, one zerk, 2-3 strokes. Use only good quality bearing grease. Deck spindle 8011-732 Deck Outer Spindle Lubricate using a grease gun, one zerk, each side 2-3 strokes. Use only good quality bearing grease. Deck outer spindle (with belt shield removed) 8061-025 Husqvarna-51 LUBRICATION Engine Oil WARNING! Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool to a safe temperature before draining. Engine Oil Filter • Drain the engine oil in accordance with the work description under the heading Engine Oil/Change Engine Oil. • Remove the oil filter. If necessary, use a filter remover. • Wipe new, clean engine oil onto the seal for the new filter. • Mount the filter by hand with +¾ turn. • Run the engine warm, then check that there are no leaks around the oil filter seal. • Check the oil level in the engine, fill if necessary. The oil filter holds 0.1 qt (0.1 liters) of oil. 8011-734 Changing the oil filter IMPORTANT INFORMATION Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location. Avoid skin contact; wash with soap and water in case of spills. Engine Oil Levels Check the oil level in the engine when the machine is standing level and the engine is stopped. Remove the dipstick, wipe it clean, and then replace it. The dipstick should be screwed into place. Take the dipstick out again and read the oil level. The oil level should lie between the markings on the dipstick. If the level is approaching the “ADD” mark, fill the oil to the “FULL” mark on the dipstick. Never fill to above the “FULL” mark. The oil is filled through the hole for the dipstick. API class SF, SG, SH, SJ or higher must be used. Synthetic oil SAE 5W-30 or 10W-30 is recommended at all temperatures. Mineral oil SAE 5W-30, 10W-30 can be used between -18 °C/0 °F and +75 °C/40 °F. At temperature above +5 °C/40 °F single grade SAE 30 must be used. See the Technical Data section for oil amounts. 52-Husqvarna 8011-500 Remove the dipstick LUBRICATION Changing the Engine Oil The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it should be changed every 50 hours. The oil drain valve is located on the left side of the unit, below the oil filter. • Place the machine on a flat surface. • Place a container under the engine where the oil drain valve exits. • Remove the valve cap. • Allow the oil to run out into the container. • Reinstall the oil drain valve cap. • Replace the oil filter if necessary. • Fill with new engine oil in accordance with Checking the Oil Level. • Start the engine. Run it for 3-5 minutes. Stop and recheck the oil level. 8009-159 The dipstick markings Husqvarna-53 LUBRICATION *Transaxle (Transmission) Fluid Change This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life, an oil filter change interval of every 200 hours is recommended. The following procedure is performed with the transaxles installed in the mower and the mower on level ground. Apply the pump release valve for each transaxle and set the parking brake. 1. Remove the three ¼" filter guard screws and filter guard. Clean any loose debris from around the perimeter of the filter. See illustration. 2. Place an oil drain pan (12" or more diameter and 8 qt. capacity is optimal) beneath the oil filter. Remove the oil filter from the transaxle. 3. After the oil has drained, wipe the filter base surface and apply a film of new oil to the gasket of the replacement filter. 4. Install the new filter by hand, turning it threequarters to one full turn after the filter gasket contacts the filter base surface. 5. Reinstall the filter guard. Torque screws to 65 in/lbs. each. 6. Repeat steps on the opposite side. 7. Drain old oil filters of all free flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area. 8. Remove the top port plug (see illustration) from the left side and right side of the transaxles prior to filling with oil. This will allow the transaxles to vent during oil fill. 9. Remove the cap from the transaxles’ expansion tank located on the vehicle frame. 10. Fill with 20W50 motor oil until oil just appears at the bottom of each transaxles’ top port (approximately 2 quarts per transaxle, 4 quarts total). Install the top port lug into each transaxle as the oil level reaches the port. 11. Install and torque the top port plugs to 180 in./lbs. 12. Continue to fill the transaxles through the expansion tank until the “Full Cold” line is reached (this will take approximately 23 additional ounces). 13. Reinstall the expansion tank cap by hand. Be careful to not overtighten. 14. Proceed to the purge procedure. 1 8019-010 1. Filter guard 2. Transaxle filter 3. Top port plug EZT filter change 1 3 1. Expansion tank 2. Tank cap 3. Transaxles EZT filter change 54-Husqvarna 2 3 2 3 8019-012 LUBRICATION Hydraulic Pump Fluid Change This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life an oil filter change interval of every 200 hours is recommended. The following procedure can be performed with the pump installed in the vehicle, and the vehicle on level ground. Apply the bypass valve and lock the vehicle parking brake. 1. Place an oil drain pan with a two gallon capacity beneath the oil filter. Remove the oil filter from the pump. 2. After the oil has drained, wipe the filter base surface off and apply a film of new oil to the gasket of the new replacement filter. 3. Prefill the oil filter with new oil and install the new filter by hand. Turn ¾ to one full turn after the filter gasket contacts the filter base surface. 4. Drain old oil filters of all free-flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area. 5. Remove the cap from the pump’s tank located on the vehicle frame. 6. Fill reservoir with SAE 10W30 oil to just above the MIN-ADD line on the reservoir. After purging, check levels and add oil if necessary. 7. Reinstall the tank cap by hand. Do not overtighten. 8. Proceed to the purge procedure. 2 3 1 8061-016 1. Pump filter 2. Pump reservoir 3. Fluid fill lines Changing the hydraulic pump oil filter Husqvarna-55 LUBRICATION Purging Procedures Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system. Resulting symptoms in hydrostatic systems may be: 1. Noisy operation. 2. Lack of power or drive after short term operation. 3. High operation temperature and excessive expansion of oil. 4. Shortened component life. Before starting, make sure the pump is at the proper oil level. If not, fill to the specifications outlined prior. The following procedures are best performed with the vehicle drive wheels off the ground, then repeated under normal operating conditions. 1. Disengage the brake if activated. 2. With the bypass valve open and the engine running at fast idle, slowly move the steering control in both forward and reverse directions (5 or 6 times). As air is purged from the unit, the oil level will drop. 3. With the bypass valve closed and the engine running, slowly move the steering control in both forward and reverse directions (5 to 6 times). Check the oil level and add oil as required after stopping the engine. 4. It may be necessary to repeat Steps 2 and 3 until all the air is completely purged from the system. When the transaxle operates at normal noise levels and moves smoothly forward and reverse at normal speeds, the transaxle is considered purged. 5. After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly. 56-Husqvarna WARNING! Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately. Disengage the parking brake 8058-020 TROUBLESHOOTING Problem Cause Engine will not start • Blade switch is engaged. • Steering controls are not locked in the neutral position • Parking brake is not activated • Battery is dead • Contamination in the carburetor or fuel line. • Fuel supply is closed or the shutoff valve for the fuel tank is in the wrong position • Clogged fuel filter or fuel line • Ignition system faulty • Battery is dead • Poor contact of the battery terminal cable connections • Blown fuse • Fault in the starter safety circuit. See Checking the Safety System in the “Maintenance Section” • Faulty carburetor • Choke control is pulled out with a warm engine • Clogged fuel filter or jet • Clogged ventilation valve on the fuel cap • Fuel tank nearly empty • Fouled spark plugs • Rich fuel mixture or fuel-air mixture. • Wrong fuel type • Water in fuel • Clogged air filter • Clogged air filter • Fouled spark plugs • Carburetor incorrectly adjusted • Air trapped in hydraulic system • Blades are loose • Blades are incorrectly balanced • Engine is loose Starter does not turn the engine over Engine runs rough Engine seems weak Machine vibrates Husqvarna-57 TROUBLESHOOTING Problem Cause Engine overheats • Clogged air intake or cooling fins • Engine overloaded • Poor ventilation around engine • Defective engine speed regulator • Too little or no oil in the engine • Contamination in the carburetor or fuel line. • Fouled spark plugs • Poor contact of the battery terminal cable connections • Charging lead is disconnected • Parking brake on • Bypass valve on pump open • Drive belt for the transmission slack or has come off • Air trapped in hydraulic system • Drive belt for the mower deck has come loose • Contact for the electromagnetic coupling has loosened • Blade switch is faulty or has come loose from cable contact • Blown fuse • Damaged seals, housing, or gaskets • Air trapped in hydraulic system • Different air pressure in tires on the left and right sides. • Bent blades • Suspending for the mower deck is uneven • Blades are dull • Driving speed too high • Grass is too long • Grass collected under the mower deck Battery not charging The machine moves slowly, unevenly, or not at all Mower deck not engaging Transaxle leaks oil Uneven mowing results 58-Husqvarna STORAGE Winter Storage At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function. Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage. Add stabilizer to the fuel in the tank or in the storage container. Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the carburetor. Do not empty the fuel tank and the carburetor if you have added stabilizer WARNING! Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes dryer, etc. Handle the fuel with care. It is very flammable and can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and far away from open flame. Never use gasoline for cleaning. Use a degreaser and warm water instead. To ready the machine for storage: 1. Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion. 2. Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose. 3. Change the engine oil; dispose of properly. 4. Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor. 5. Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug. 6. Lubricate all grease zerks, joints, and axles. 7. Remove the battery. Clean, charge, and store the battery in a cool place, but protect it from direct cold. 8. Store the machine in a clean, dry place and cover it for extra protection. Service When ordering spare parts, please specify the purchase year, model, type, and serial number. Always use genuine Husqvarna spare parts. An annual check-up at an authorized service workshop is a good way to ensure that the machine performs its best the following season. Husqvarna-59 schematics NOTE: 1. SEAT UNOCCUPIED 2. BRAKE SWITCH IN OFF POSITION 3. MOTION CONTROL LEVERS OUT 4. PTO IN OFF POSITION KEY SWITCH POSITIONS SOLENOID POSITION 1 - OFF YEL RED/BLK YEL YEL BRAKE SW. RIGHT MOTION CONTROL LEVER RED/BLK TO ENGINE PIGTAIL GRN BRN WHT GRY BRN 20 AMP PUR YEL/RED WHT YEL POSITION 2 - RUN1 RED BLK BRN WHT POSITION 3 - RUN2 GRN LEFT MOTION CONTROL LEVER BLU BLK PUR YEL BLK BRN BRN BRN SEAT SW. BLU 7.5 AMP PTO SW. BLK HOURMETER BLK ACCESSORY OUTLET ELECTRIC CLUTCH ENGINE GROUND 60-Husqvarna POSITION 4 - START PUR PUR BLK TECHNICAL DATA Accessories Collection system Torque Specifications Engine crankshaft bolt Deck pulley bolts Lug nuts Blade bolt 50 ft/lb (67 Nm) 150 ft/lb (203 Nm) 75 ft/lb (100 Nm) 90 ft/lb (122 Nm) Standard ¼" fasteners Standard 5/16" fasteners Standard 3/8" fasteners Standard 7/16" fasteners Standard ½” fasteners 9 ft/lb (12 Nm) 18 ft/lb (25 Nm) 33 ft/lb (44 Nm) 52 ft/lb (70 Nm) 80 ft/lb (110 Nm) HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Shank Size (Diameter in inches, fine or coarse thread) Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut ft./lbs ft./lbs Nm ft./lbs Nm ¼ 9 12 13 18 /16 18 24 28 /8 31 42 46 7 /16 50 68 75 108 ½ 75 102 115 156 9 /16 110 150 165 224 5 3 ft./lbs Nm 38 24 33 62 40 54 /8 150 203 225 305 ¾ 250 339 370 502 /8 378 513 591 801 1 /8 782 1060 1410 1912 5 7 1 ** Grade 5 - Minimum commercial quality (lower quality not recommended) Metric Standard Hardware Shank Size (Diameter in millimeters, fine or coarse thread) Grade Grade 8.8 Grade 10.9 Grade 12.9 ft./lbs ft./lbs Nm ft./lbs Nm ft./lbs Nm M4 1.5 2 2.2 3 2.7 3.6 M5 3 4 4.5 6 5.2 7 M6 5.2 7 7.5 10 8.2 11 M7 8.2 11 12 16 15 20 M8 13.5 18 18.8 25 21.8 29 M10 24 32 35.2 47 43.5 58 M12 43.5 58 62.2 83 75 100 M14 70.5 94 100 133 119 159 M16 108 144 147 196 176 235 M18 142 190 202 269 242 323 M20 195 260 275 366 330 440 M22 276 368 390 520 471 628 M24 353 470 498 664 596 794 M27 530 707 474 996 904 1205 Husqvarna-61 TECHNICAL DATA EZ4824 / 965880301K EZ4824 / 965880401 Engine Manufacturer Kohler Briggs & Stratton Courage Endurance 24 hp* 24 hp* Pressure with oil filter Pressure with oil filter Oil capacity excluding filter 1.78 qts / 1.65 liters 1.78 qts / 1.65 liters Oil capacity including filter 2 qts / 1.89 liters 2 qts / 1.89 liters SAE 10W30, 10W40, 5W20, 5W30, API SF-SJ SAE 10W30, 10W40, 5W20, 5W30, API SF-SJ Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Fuel tank capacity 4 gallons / 15.1 liters 4 gallons / 15.1 liters Spark plugs / gap Champion RC12YC .030" / 0.75 mm Champion XC12YC .030" / 0.75 mm Cooling Air cooled Air cooled Air filter Standard Standard 12V 12V Electric Electric Hydrostatic pump ZT2800 Hydro Gear Dual levers, foam gripped Dual levers, foam gripped Type Power Lubrication Engine oil (See viscosity diagram) Fuel Alternator Starter Transmission Transmission Speed and direction controls Speed forward 0-8 mph / 0-12.9 km/h 0-7 mph / 0-11.3 km/h Speed reverse 0-4 mph / 0-6.4 km/h 0-3.5 mph / 0-5.6 km/h Mechanical parking brake Mechanical parking brake 13 x 5.0-6, 4 ply 13 x 5.0-6, 4 ply 22 x 9.5-10 20 x 8-8 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar Brakes Front caster tires, smooth tread Rear tires, turf pneumatic Tire pressure *As rated by the engine manufacturer. 62-Husqvarna TECHNICAL DATA EZ4824 / 965880301K EZ4824 / 965880401 Cutting Width 48" / 122cm 48" / 122cm Cutting Height 1.5 - 4.5" / 3.8 - 11.4 cm 1.5 - 4.5" / 3.8 - 11.4 cm Uncut Circle 0 0 Number of Blades 3 3 Blade Length 16.25" / 41 cm 16.25" / 41 cm Nose Rollers No No Sprung Seat Standard Standard Hinged Arm Rests Standard Standard Hour Meter Standard Standard Blade Engagement Electromagnetic clutch Electromagnetic clutch Deck Construction 11 gauge w/ 10 gauge skirts 11 gauge w/ 10 gauge skirts 3.2 acres /h 12950 m /h 2.9 acres /h 11770 m2/h Weight 605 / 274 kg 605 lbs / 274 kg Base Machine Length 76" / 193 cm 74½" / 189 cm Base Machine Height 47" / 119 cm 47" / 119 cm Base Machine Width 46½" / 118 cm 46½" / 118 cm Overall Width, Chute Up 48½" / 123 cm 48½" / 123 cm Overall Width, Chute Down 59¾" / 152 cm 59¾" / 152 cm Frame Productivity 2 Dimension Husqvarna-63 TECHNICAL DATA EZ5224 / 965880601 EZ5226 / 965921601 Kohler Briggs & Stratton Courage Endurance 24 hp* 26 hp* Pressure with oil filter Pressure with oil filter Oil capacity excluding filter 1.78 qts / 1.65 liters 1.78 qts / 1.65 liters Oil capacity including filter 2 qts / 1.89 liters 2 qts / 1.89 liters SAE 10W30, 10W40, 5W20, 5W30, API SF-SJ SAE 10W30, 10W40, 5W20, 5W30, API SF-SJ Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Fuel tank capacity 4 gallons / 15.1 liters 4 gallons / 15.1 liters Spark plugs / gap Champion RC12YC .030" / 0.75 mm Champion XC12YC .030" / 0.75 mm Cooling Air cooled Air cooled Air filter Standard Standard Engine Manufacturer Type Power Lubrication Engine oil (See viscosity diagram) Fuel Alternator 12V 12V Electric Electric Hydrostatic pump ZT2800 Hydro Gear Dual levers, foam gripped Dual levers, foam gripped Speed forward 0-8 mph / 12.9 km/h 0-7 mph / 0-11.3 km/h Speed reverse 0-4 mph / 0-6.4 km/h 0-4 mph / 0-6.4 km/h Mechanical parking brake Mechanical parking brake 13 x 5.0-6, 4 ply 11 x 4.5, 4 ply 22 x 9.5-10 20 x 10-8 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar Starter Transmission Transmission Speed and direction controls Brakes Front caster tires, smooth tread Rear tires, turf pneumatic Tire pressure 64-Husqvarna TECHNICAL DATA EZ5224 / 965880601 EZ5226 / 965921601 Cutting Widthr 52" / 132cm 52" / 132cm Cutting Height 1.5 - 4.5" / 3.8 - 11.4 cm 1.5 - 4.5" / 3.8 - 11.4 cm Frame Uncut Circle 0 0 Number of Blades 3 3 Blade Length 18" / 45.7 cm 18” / 45.7 cm Nose Rollers Yes Yes Sprung Seat Standard Standard Hinged Arm Rests Standard Standard Hour Meter Standard Standard Blade Engagement Electromagnetic clutch Electromagnetic clutch Deck Construction 11 gauge w/ 10 gauge skirts 11 gauge w/ 10 gauge skirts 3.57 acres /h 14447 m /h 3.13 acres /h 12648 m2/h Productivity 2 Dimension Weight 660 lbs / 299 kg 660 lbs / 299 kg Base Machine Length 76" / 193 cm 74½" / 189 cm Base Machine Height 47" / 119 cm 47" / 119 cm Base Machine Width 46½" / 118 cm 46½" / 118 cm Overall Width, Chute Up 52½" / 133 cm 52½" / 133 cm Overall Width, Chute Down 66¼" / 168 cm 66¼" / 168 cm Husqvarna-65 TECHNICAL DATA EZ5221 / 965880501 EZ6124 / 965880701 Kawasaki Kohler FJ641V-AS01 Courage 21 hp* 24 hp* Pressure with oil filter Pressure with oil filter Oil capacity excluding filter 1.9 qt / 1.8 liter 1.78 qts / 1.68 liters Oil capacity including filter 2.2 qt / 2.1 liter 2 qts / 1.89 liters SAE 10W30, 5W30, 5W20, SAE 30, API SF,SG,SH SAE 10W30, 10W40, 5W20, 5W30, API SF-SJ Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Fuel tank capacity 4 gallon / 15.1 liters 4 gallon / 15.1 liters Spark plugs / gap NGK BPR5ES .030" / 0.75 mm Champion XC12YC .030" / 0.75 mm Cooling Air cooled Air cooled Air filter Standard Standard Engine Manufacturer Type Power Lubrication Engine oil (See viscosity diagram) Fuel Alternator 12V 12V Electric Electric Hydrostatic pump Hydrostatic pump Dual levers, foam gripped Dual levers, foam gripped Speed forward 0-9.5 mph / 15.3 km/h 8 mph / 12.9 km/h Speed reverse 0-5 mph / 0-8 km/h 4 mph / 6.45 km/h Mechanical parking brake Mechanical parking brake 13 x 5.0-6, 4 ply 13 x 5.0-6, 4 ply 22 x 9.5-10 22 x 9.5-10 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar Starter Transmission Transmission Speed and direction controls Brakes Front caster tires, smooth tread Rear tires, turf pneumatic Tire pressure *As rated by the engine manufacturer. 66-Husqvarna TECHNICAL DATA EZ5221 / 965880501 EZ6124 / 965880701 Cutting Widthr 52" / 132cm 61" / 155cm Cutting Height 1.5 - 4.5" / 3.8 - 11.4 cm 1.5 - 4.5" / 3.8 - 11.4 cm Frame Uncut Circle 0 0 Number of Blades 3 3 Blade Length 18" / 45.7 cm 21" / 53.3 cm Nose Rollers Yes Yes Sprung Seat Standard Standard Hinged Arm Rests Standard Standard Hour Meter Standard Standard Blade Engagement Electromagnetic clutch Electromagnetic clutch Deck Construction 11 gauge w/ 10 gauge skirts 11 gauge w/ 10 gauge skirts 3.57 acres /h 14447 m /h 4.18 acres /h 16955 m2/h Productivity 2 Dimension Weight 660 lbs / 299 kg 690 lbs / 313 kg Base Machine Length 76" / 193 cm 76" / 193 cm Base Machine Height 47" / 119 cm 47" / 119 cm Base Machine Width 46½" / 118 cm 46½" / 118 cm Overall Width, Chute Up 52½" / 133 cm 61¾" / 157 cm Overall Width, Chute Down 66¼" / 168 cm 75½" / 192 cm Husqvarna-67 CONForMITY CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents. CE requirements The Declaration of Conformity is included in the literature packet. 68-Husqvarna WARRANTY All Husqvarna products can be registered online at www.usa.husqvarna.com quickly and easily regardless of their model year. Click the Support tab, click on the Online Product Registration link and fill out the electronic form and submit. Ask about Husqvarna’s extended service plan! SECTION 1 - LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship from the date of purchase for the period of the applicable “Warranty Schedule” of the Product as set forth below. Additional limitations are described in Section 2 through 6, inclusive. l PRODUCT CONSUMER l WARRANTY SCHEDULE COMMERCIAL/PROFESSIONAL WARRANTY SCHEDULE RENTAL WARRANTY SCHEDULE Zero Turn Rider 3 Years or 600 Hours 1 Year or 600 Hours 90 Days All consumer product use must have been limited to the owner’s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use. SECTION 2 - HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period. SECTION 3 - ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this warranty: (1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to belts, blades, blade adapters, bulbs, clutches, clutch drums, filters (fuel line, fuel filters, air filters, oil filters), sprockets, guide bars, lubricants, rewind springs, spark plugs; (2) Natural discoloration of material due to ultraviolet light; (3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer. (4) Lawn and garden attachments that are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer. (5) Commercial or consumer mowing decks with sand abrasion damage. (6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are manufactured by third party engine manufacturer. SECTION 4 - EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following: (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; (2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna; (3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or: (4) Additional damage to parts or components due to continued use occurring after any of the above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS. Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary by state. SECTION 5 - CUSTOMER RESPONSIBILITIES The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner’s/ Operator’s manual. Should an operational problem or failure occur, the product should not be used. Failure caused by continued use is not covered by warranty. Product should be delivered, at owners expense, as is, to an authorized Husqvarna Servicing Retailer for evaluation. Proof of purchase, as explained in section 6, rests solely with the customer. SECTION 6 - PROCEDURE TO OBTAIN WARRANTY CONSIDERATION It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna. This card should be mailed within ten (10) days from the date of purchase in order to confirm the warranty and to facilitate post-sale service. Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address of the selling retailer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be delivered at the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna retailer can be located by calling 1-800-HUSKY-62 or visiting www.husqvarna.com Subject to change without notice. Husqvarna-69 SERVICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ □ 1. Charge the battery. 2. Adjust the tire pressure of all wheels to 15 PSI (1 bar). 3. Mount the steering controls in the normal position. 4. Connect the contact box to the cable for the seat’s safety switch. 5. Check that the right amount of oil is in the engine. 6. Adjust the position of the steering controls. 7. Fill with fuel and open the fuel shut off valve. 8. Start the engine. 9. Check that there is drive to both wheels. 10. Check the mower deck adjustment. 11. Check: The safety switch for the parking brake. The safety switch for the mower deck. The safety switch in the seat. The safety switch in the steering controls. Parking brake functionality. Driving forward. Driving backward. Engaging the blades. 12. Check the idle speed 13. Check the engine high idle speed 14. Inform the customer about: The need and advantages of following the service schedule. The need and advantages of leaving the machine for service every 300 hours. Delivery service has been carried out. The effects of service and maintaining a service journal on the machine’s resale value. Certified: Application areas for mulching. 15. Fill in the sales papers 70-Husqvarna No remaining notes. SERVICE JOURNAL Action After the First 5-8 Hours 1. Change engine oil. Date, mtr reading, stamp, sign □ Husqvarna-71 SERVICE JOURNAL Action Date, mtr reading, stamp, sign 25-Hour Service □ □ □ □ □ □ □ 1. Check the engine air filter. 2. Sharpen/Replace mower blades if required. 3. Check the tire pressures. 4. Check battery with cables. 5. Lubricate according to lubrication chart. 6. Check/clean the engine’s cooling air intake. 7. Clean the air cleaner’s prefilter (foam). 72-Husqvarna SERVICE JOURNAL Action 50-Hour Service 1. Perform the 25-hour service. 2. Clean/replace the air cleaner’s filter cartridge (paper filter) (shorter intervals for dusty operating conditions). 3. Change engine oil. 4. Lubricate according to lubrication chart. 5. Check/adjust the parking brake. 6. Change hydraulic pump oil and filter. Date, mtr reading, stamp, sign □ □ □ □ □ □ Husqvarna-73 SERVICE JOURNAL Action Date, mtr reading, stamp, sign 100-Hour Service □ □ □ □ □ □ □ □ □ 1. Perform the 25-hour service. 2. Perform the 50-hour service. 3. Change the engine oil filter. 4. Clean/replace the spark plugs. 5. Replace the fuel filter. 6. Check V-belts. 7. Check tighten caster wheel axle bolts (every 200 hours). 8. Change the air filter’s paper cartridge. 9. Change hydraulic pump oil and filter. (200 hours) 74-Husqvarna SERVICE JOURNAL Action 300-Hour Service 1. Perform the 25-hour service. 2. Perform the 50-hour service. 3. Perform the 100-hour service. 4. Check/adjust the mower deck. 5. Clean the combustion chamber and grind the valve seats. 6. Check the engine valve clearance. 7. Replace the air cleaner’s prefilter (foam). Date, mtr reading, stamp, sign □ □ □ □ □ □ □ Husqvarna-75 SERVICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Year □ □ □ □ □ □ □ □ □ □ 1. Clean the engine’s cooling air intake (25 hours). 2. Replace the air cleaner’s pre-filter (foam) (300 hours). 3. Replace the air filter’s paper cartridge. 4. Change the engine oil (50 hours). 5. Replace the engine oil filter (100 hours). 6. Check/adjust the cutting height. 7. Check/adjust the parking brake (50 hours). 8. Clean/change the spark plugs (100 hours). 9. Change the fuel filter (100 hours). 10. Check the engine valve clearance. 76-Husqvarna SERVICE JOURNAL Action Date, mtr reading, stamp, sign Husqvarna-77 P/N 115 129627 IR 10/29/08
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2008:11:12 09:28:35-06:00 Subject : HOEN_2008, 115129627 Modify Date : 2008:11:13 19:43:35-05:00 Page Mode : UseOutlines Producer : Adobe PDF Library 8.0 Trapped : False Creation Date : 2008:11:12 09:28:35-06:00 Mod Date : 2008:11:13 19:43:35-05:00 Author : HUSQVARNA Metadata Date : 2008:11:13 19:43:35-05:00 Creator Tool : Adobe InDesign CS3 (5.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 5185 bytes, use -b option to extract) Instance ID : uuid:6394e325-36fa-4462-8912-38c30e1e2f5c Document ID : adobe:docid:indd:44da525b-b0c8-11dd-b1a4-b6c61bf32f90 Rendition Class : proof:pdf Derived From Instance ID : 44da5256-b0c8-11dd-b1a4-b6c61bf32f90 Derived From Document ID : adobe:docid:indd:71419091-a5ca-11dd-94a6-df723cb4f2a9 Format : application/pdf Title : OM, EZ ZERO TURN MOWER, EZ 4824 EC/ EZ 4824 K/ EZ 4824/ EZ 5221/ EZ 5224/ EZ 5226/ EZ 6124, 965880201, 965880301, 965880401, 965880501, 965880601, 965880701, 965921601, 2008-11, Ride Mower (Turf Care) Description : HOEN_2008, 115129627 Creator : HUSQVARNA Page Count : 80 Page Layout : OneColumnEXIF Metadata provided by EXIF.tools