Husqvarna Lgt2654 Owners Manual ManualsLib Makes It Easy To Find Manuals Online!

2014-12-11

: Husqvarna Husqvarna-Lgt2654-Owners-Manual-120262 husqvarna-lgt2654-owners-manual-120262 husqvarna pdf

Open the PDF directly: View PDF .
Page Count: 48

Download
Open PDF In Browser	View PDF

03002

LGT2654
Owner's Manual

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

•

WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.

•
•
•

WARNING: Do not coast down a hill
in neutral, you may lose control of the
tractor.

•
•

WARNING: Tow only the attachments
that are recommended by and comply with specifications of the manufacturer of your tractor. Use common
sense when towing. Operate only at
the lowest possible speed when on a
slope. Too heavy of a load, while on
a slope, is dangerous. Tires can lose
traction with the ground and cause you
to lose control of your tractor.

•
•
•
•

WARNING

•

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.

•

WARNING

II. SLOPE OPERATION

Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.

I. GENERAL OPERATION
•
•
•
•
•
•
•
•

Read, understand, and follow all instructions on the
machine and in the manual before starting.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the
blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.

Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
• Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot
on the ground.
• Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
III. CHILDREN

GENERAL SERVICE
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
• If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine
running.
• Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service
as required.
• Maintain or replace safety and instruction labels, as
necessary.

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the
area.
• Before and while backing, look behind and down for
small children.
• Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.

IV. TOWING
•
•
•
•
•

Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.

•
•
•

V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
• Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.

•

•
•
•
•
•
•
•
•

Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

Gasoline Capacity
and type:

4 Gallons
Unleaded Regular

•
•

Oil Type (API-SG-SL):

SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)

•

Oil Capacity:

W/ Filter: 64 oz
W/O Filter: 60 oz

Spark Plug:
(Gap: .040")

Champion QC12YC

Ground Speed (MPH):

Forward:
Reverse:

Charging System:

16 AMPS @ 3600 RPM

Battery:

AMP/HR:
MIN. CCA:
Case Size:

Blade Bolt Torque:

45-55FT. LBS.

Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
federal lands.
A spark arrester for the muffler is available through your
nearest authorized service center/department (See REPAIR
PARTS section of this manual).

0 – 5.8
0 – 2.1
35
280
U1R

CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/
department We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.

TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY ................................................................. 6-9
OPERATION ........................................................... 10-16
MAINTENANCE SCHEDULE ...................................... 17

MAINTENANCE ..................................................... 17-20
SERVICE AND ADJUSTMENTS ............................ 21-25
STORAGE .................................................................... 26
TROUBLESHOOTING ............................................ 27-28
REPAIR PARTS ...................................................... 30-43
WARRANTY................................................................. 44

UNASSEMBLED PARTS
Mower

(5) Large Retainer
Springs - 7/16

Mower Front Wheel

(1) 3/4 O.D. Washers
(1) Wheel
(1) 1-1/4 O.D. Washer

(2) Smaller Retainer
Springs - 5/16

(5) 1-3/16 O.D. Washers

(1) Shoulder Bolt

(1) Locknut
3/8-16

(1) Anti-Sway Bar

Slope Sheet
(1) Oil Drain Tube
For Future Use

Keys
(1) Front Link
Assembly

(2) Rear Lift Link
Assemblies

(2) Keys

ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 3/4" wrench
(1) Utility knife
(1) 9/16" wrench
(1) Pliers
(1) Tire Pressure Gauge
When right or left hand is mentioned in this manual, it
means from your point of view, when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM
CARTON

FIG. 2

UNPACK CARTON
•

•
•
•

Remove all accessible loose parts and parts cartons
from carton .
Cut along dashed lines on all four panels of carton.
Remove end panels and lay side panels flat.
Remove mower and packing materials.
Check for any additional loose parts or cartons and
remove.

NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.

CHECK BATTERY (See Fig. 1)

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of
controls)

• Lift hood to raised position.
NOTE: If this battery is put into service after month and year
indicated on label (L) (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance section of this manual
for charging instructions).

•
•
•
•

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of
controls)

•

02931

FIG. 1

ADJUST SEAT (See Fig. 2)
•
•
•

Raise attachment lift lever to its highest position.
Release parking brake by depressing brake pedal.
Place freewheel control in disengaged position to disengage transmission (See “TO TRANSPORT” in the
Operation section of this manual).
Roll tractor forward off skid.

Sit in seat.
Lift up adjustment lever (A) and slide seat until a comfortable position is reached which allows you to press
clutch/brake pedal all the way down.
Release lever to lock seat in position.

Be sure all the above assembly steps have been completed.
• Check engine oil level and fill fuel tank with gasoline.
• Place freewheel control in "transmission engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
• Sit on seat in operating position, depress brake pedal
and set the parking brake.
• Raise attachment lift lever to its highest position.
• Remove key from bag and start the engine (see "TO
START" in the Operation section of this manual). After
engine has started, move throttle control to idle (slow)
position.
• Release parking brake.
• Slowly depress forward drive pedal and drive tractor
off skid.
• Apply brake to stop tractor and set parking brake.
• Turn ignition key to "STOP" position.
Continue with the instructions that follow.

ASSEMBLY
ASSEMBLE FRONT WHEEL TO
MOWER (See Fig. 3)

Using shoulder bolt, washer and locknut from parts
bag, assemble front wheel to mower as shown. Tighten
securely.

02
05
1

•

A
FIG. 5
NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor.
• Slide mower under tractor until it is centered under
tractor.
• FIRST INSTALL ANTI-SWAY BAR (S).
- From right side of mower, insert anti-sway bar into
hole in transmission bracket (T).

FIG. 3

INSTALL MOWER AND DRIVE BELT

(See Figs. 4-12)

See MOWER AND DRIVE BELT ASSEMBLY Supplement
Sheet for additional guidance on this assembly.
Be sure tractor is on level surface and engage parking
brake.
• Lower attachment lift lever to it's lowest position.

CAUTION: Lift lever is spring loaded. Have
a tight grip on lift lever, lower it slowly and
engage in lowest position.
•

Turn steering wheel to the left as far as it will go and
position mower on right side of tractor with deflector
shield to the right.

A
02995

FIG. 6
- Pivot bar towards you and insert other end of bar
into hole in rear mower bracket (D). Move mower as
needed to insert bar.
- Secure with washer and retainer spring as shown
using small 5/16 retainer spring.

D
02965

FIG. 4
•

Remove plastic tie securing belt, bring belt forward
and check belt for proper routing in all mower pulley
grooves.
02996

FIG. 7

ASSEMBLY
•

•

ATTACH MOWER SIDE SUSPENSION ARMS (A) TO
CHASSIS - Position hole in arm over pin (B) on outside
of tractor chassis and secure with washer and retainer
spring.
Repeat on opposite side of tractor.

•
•

•

Turn steering wheel to position wheels straight forward.
ATTACH FRONT LINK (E) - Work from left side of
tractor. Insert rod end of link assembly through front
hole in tractor front suspension bracket (F) and secure
with7/16 retainer spring (G) through hole in link located
behind the bracket.
Insert other end of link (E) into hole in front mower
bracket (H) and secure with washer and 5/16 retainer
spring (J).

FIG. 8

•

ATTACH REAR LIFT LINKS (C) - Insert rod end of lift
link assembly into hole in tractor lift shaft suspension
arm (L) and pivot link down to mower. Lift rear corner
of mower and position slot in link assembly over pin on
rear mower bracket (D) and secure with washer and
retainer spring.
Repeat on opposite side of tractor.

5/16
J

G
7/16

FIG. 10

•

Disengage belt tension rod (K) from locking bracket
(L).
• Install belt onto engine clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.

L
C

FIG. 9
L

B
M

K
F

E
H

FIG. 11

ASSEMBLY
✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY
PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓ All assembly instructions have been completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and charged.
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓ Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓ Check wiring. See that all connections are still secure
and wires are properly clamped.
✓ Before driving tractor, be sure freewheel control is in
“transmission engaged” position (see “TO TRANSPORT” in the Operation section of this manual).
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓ Become familiar with all controls, their location and
function. Operate them before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
✓ It is important to purge the transmission before operating your tractor for the first time. Follow proper
starting and transmission purging instructions (See
“TO START ENGINE” and “PURGE TRANSMISSION”
in the Operation section of this manual).

FIG. 12
•

Engage belt tension rod (K) on locking bracket (L).
CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and engage slowly.

•
•

Raise attachment lift lever to highest position.
If necessary, adjust gauge wheels before operating
mower as shown in the Operation section of this
manual.

CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly
leveled. See “TO LEVEL MOWER HOUSING” in the Service
and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.

CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that
the brake is operating properly. See “TO CHECK BRAKE”
in the Service and Adjustments section of this manual.

OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

REVERSE

ENGINE OFF

LIGHTS ON

NEUTRAL

REVERSE
OPERATION
SYSTEM (ROS)

FUEL

HIGH

LOW

ENGINE ON

BATTERY

CHOKE

ENGINE START

REVERSE

FAST

IGNITION SWITCH

PARKING BRAKE

FORWARD

SLOW

MOWER HEIGHT

MOWER LIFT

CLUTCH/BRAKE
PEDAL

CRUISE CONTROL
15

ATTACHMENT
CLUTCH DISENGAGED

ATTACHMENT
CLUTCH ENGAGED

DANGER, KEEP HANDS
AND FEET AWAY

SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.

FREE WHEEL
(Automatic Models only)

WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.

Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.

HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.

OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.

P
H

E
G
K
L

N
B

Q
C

FIG. 13
Our tractors conform to the applicable safety standards of the American National Standards Institute.
(H) LIGHT SWITCH – Turns the headlights on and off.
(J) CRUISE CONTROL LEVER – Used to set forward
movement of tractor at desired speed without holding the
forward drive pedal.
(K) FORWARD DRIVE PEDAL – Used for forward movement
of tractor.
(L) REVERSE DRIVE PEDAL – Used for reverse movement of
tractor.
(M) FREEWHEEL CONTROL – Disengages transmission for
pushing or slowly towing the tractor with the engine off.
(N) CHOKE CONTROL – Used when starting a cold engine.
(P) SERVICE REMINDER / HOUR METER – Indicates when
service is required for the engine and mower.

(A) ATTACHMENT LIFT LEVER – Used to raise and lower the
mower or other attachments mounted to your tractor.
(B) BRAKE PEDAL – Used for braking the tractor and starting
the engine.
(C) PARKING BRAKE – Locks clutch/brake pedal into the
brake position.
(D) THROTTLE CONTROL – Used to control engine speed.
(E) ATTACHMENT CLUTCH SWITCH – Used to engage the
mower blades, or other attachments mounted to your tractor.
(F) IGNITION SWITCH – Used for starting and stopping the
engine.
(G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION
– Allows operation of mower or other powered attachment
while in reverse.

(Q) 12-VOLT POWER PORT – Used for 12-volt accessories.

OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor
or performing any adjustments or repairs. We recommend standard safety glasses or a wide
vision safety mask worn over spectacles.

HOW TO USE YOUR TRACTOR

IMPORTANT: Leaving the ignition switch in any position
other than "STOP" will cause the battery to discharge and
go dead.
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

TO SET PARKING BRAKE(See Fig. 14)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress brake pedal (B) all the way down and hold.
• Pull parking brake lever (C) up and hold, release pressure from brake pedal (B), then release parking brake
lever. Pedal should remain in brake position. Make
sure parking brake will hold tractor secure.

CAUTION: Always stop tractor completely, as described above, before
leaving the operator's position.

D
B
N

FIG. 14

FIG. 16

STOPPING

TO USE THROTTLE CONTROL (See Fig. 16)

MOWER BLADES
• To stop mower blades, push attachment clutch switch in
to disengaged position (o).

Always operate engine at full speed (fast).
• Operating engine at less than full speed (fast) reduces
engines operating efficiency.
• Full speed (fast) offers the best bagging and mower
performance.

TO USE CHOKE CONTROL -D (See Fig. 16)
(I) ATTACHMENT
CLUTCH SWITCH
PULL OUT TO “ENGAGE”

Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.

(O) PUSH-IN TO
“DISENGAGED”

TO MOVE FORWARD AND BACKWARD -N
(See Fig. 17)

FIG. 15
GROUND DRIVE • To stop ground drive, depress brake pedal all the way
down.
ENGINE • Move throttle control (D) between half and full speed
(fast) position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping, may cause engine to “backfire”.
• Turn ignition key (F) to “STOP” position and remove
key. Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke (N) to stop engine.

The direction and speed of movement is controlled by the
forward and reverse drive pedals.
• Start tractor and release parking brake.
• Slowly depress forward (K) or reverse (L) drive pedal to
begin movement. Ground speed increases the further
down the pedal is depressed.

OPERATION
•

•

The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 19)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
NOTE: Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of
manual).
• With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off
the ground. Install gauge wheel in appropriate hole.
Tighten securely.
• Repeat for all, installing gauge wheel in same adjustment hole.

K
L

FIG. 17

TO USE CRUISE CONTROL -J (See Fig. 17)
The cruise control feature can be used for forward travel
only.
SYSTEM CHARACTERISTICS
The cruise control should only be used while mowing or
transporting on relatively smooth, straight surfaces. Other
conditions such as trimming at slow speeds may cause the
cruise control to disengage. Do not use the cruise control
on slopes, rough terrian or while trimmimg or turning.
• With forward drive pedal depressed to desired speed,
pull cruise control lever (J) up and hold while lifting
your foot off the pedal, then release the lever.
To disengage the cruise control, depress the brake pedal
or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 18)
The position of the attachment lift lever (A) determines the
cutting height.

FIG.19

TO OPERATE MOWER
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged
will shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough,
rolling terrain or hills.
• Select desired height of cut with attachment lift lever.
• Start mower blades by engaging attachment clutch
control.

FIG. 18
• Put attachment lift lever in desired cutting height slot.
The cutting height range is approximately 1" to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate and
may vary depending upon soil conditions, height of grass
and types of grass being mowed.

TO STOP MOWER BLADES disengage attachment clutch control.
CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield (S) in place.

OPERATION
•
•
S

•

To restart movement, slowly release parking brake and
brake pedal.
Slowly depress appropriate drive pedal to slowest setting.
Make all turns slowly.

TO TRANSPORT (See Figs. 13 and 21)
When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling
position. Free wheel control is located at the rear drawbar
of tractor.
• Raise attachment lift to highest position with attachment
lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.
• Do not push or tow tractor at more than two (2)
MPH.
• To reengage transmission, reverse above procedure.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).

FIG. 20

REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position.
WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.

Transmission Engaged

USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders
will enter the mowing area.
• Depress brake pedal all the way down.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before and while backing.
• Slowly depress reverse drive pedal to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
ROS "ON" POSITION

Transmission Disengaged

FIG. 21

SERVICE REMINDER/HOUR METER
Service reminder shows the total number of hours the
engine has run and flashes to indicate that the engine
or mower needs servicing. When service is required, the
service reminder will flash for two hours. To service engine
and mower, see the Maintenance section of this manual.
NOTE: Service reminder runs when the ignition key is in
any position but "STOP". For accurate reading, be sure
key remains in the "STOP" position when engine is not
running.

ENGINE "ON" POSITION
(NORMAL OPERATING)

TOWING CARTS AND OTHER ATTACHMENTS

02828

TO OPERATE ON HILLS

Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.

CAUTION: Do not drive up or down hills
with slopes greater than 15° and do not
drive across any slope.
•
•
•

Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If stopping is absolutely necessary, push brake pedal
quickly to brake position and engage parking brake.

OPERATION
•

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
• Check engine oil with tractor on level ground.
• Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
• For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
• To change engine oil, see the Maintenance section in
this manual.

WARM WEATHER STARTING (50° F and above)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. If the engine starts
to run roughly, pull the choke control out slightly for a
few seconds and then continue to push the control in
slowly.
• The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.

ADD GASOLINE
•

Insert key into ignition and turn key clockwise to “START”
position and release key as soon as engine starts. Do not
run starter continuously for more than fifteen seconds
per minute. If the engine does not start after several
attempts, push choke control in, wait a few minutes and
try again. If engine still does not start, pull the choke
control out and retry.

COLD WEATHER STARTING (50° F and below)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. Continue to push
the choke control in small steps allowing the engine to
accept small changes in speed and load, until the choke
control is fully in. If the engine starts to run roughly, pull
the choke control out slightly for a few seconds and
then continue to push the control in slowly. This may
require an engine warm-up period from several seconds
to several minutes, depending on the temperature.

Fill fuel tank to bottom of filler neck. Do not overfill. Use
fresh, clean, regular unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce valve life). Do not
mix oil with gasoline. Purchase fuel in quantities that can
be used within 30 days to assure fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.

AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Release the parking brake and let the brake slowly
return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can be used during the engine warm-up
period after the transmission has been warmed up and
may require the choke control be pulled out slightly.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.

IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.

CAUTION: Alcohol blended fuels (called gasohol or
using ethanol or methanol) can attract moisture which
leads to separation and formation of acids during
storage. Acidic gas can damage the fuel system of
an engine while in storage. To avoid engine problems,
the fuel system should be emptied before storage
of 30 days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and carburetor
are empty. Use fresh fuel next season. See Storage
Instructions for additional information. Never use
engine or carburetor cleaner products in the fuel
tank or permanent damage may occur.

PURGE TRANSMISSION

TO START ENGINE (See Fig. 13)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
• Be sure freewheel control is in the transmission engaged
position.
• Sit on seat in operating position, depress brake pedal
and set parking brake.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to fast position
• Pull choke control out for a cold engine start attempt.
For a warm engine start attempt the choke control may
not be needed.
NOTE: Before starting, read the warm and cold starting
procedures below.

CAUTION: Never engage or disengage
freewheel lever while the engine is running.
To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.

OPERATION
•
•
•

MOWING TIPS

Place tractor safely on a level surface - that is clear
and open - with engine off and parking brake set.
Disengage transmission by placing freewheel control
in freewheeling position (See “TO TRANSPORT” in this
section of manual).
Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position.
Disengage parking brake

•
•
•

CAUTION: At any time, during step 4,
there may be movement of the drive
wheels.

•

Depress forward drive pedal to full forward position,
hold for five (5) seconds and release pedal. Depress
reverse drive pedal to full reverse position, hold for five
(5) seconds and release pedal. Repeat this procedure
three (3) times.
• Shut- off engine and set parking brake.
• Engage transmission by placing freewheel control in
engaged position (See “TO TRANSPORT” in this section of manual).
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed.
Disengage parking brake.
• Drive tractor forward for approximately five feet then
backwards for five feet. Repeat this driving procedure
three times.
Your transmission is now purged and now ready for normal
operation.

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
When mowing large areas, start by turning to the right so
that clippings will discharge away from shrubs, fences,
driveways, etc. After one or two rounds, mow in the
opposite direction making left hand turns until finished
(See Fig. 22).

FIG. 22
•

•
•

•

If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.

MAINTENANCE
MAINTENANCE
SCHEDULE

BEFORE
EACH
USE

EVERY
8
HOURS

EVERY
25
HOURS

EVERY
50
HOURS

EVERY
100
HOURS

EVERY
SEASON

BEFORE
STORAGE

Check Brake Operation
Check Tire Pressure

T Check Operator Presence & ROS Systems
R
A Check for Loose Fasteners
C Check/Replace Mower Blades
T Lubrication Chart
0 Check Battery Level
R Clean Battery and Terminals

Check Transaxle Cooling
Check Mower Levelness
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)

1,2

Change Engine Oil (without oil filter)

1,2

E Clean Air Filter
N
G Clean Air Screen
I Inspect Muffler/Spark Arrester
N Replace Oil Filter (If equipped)
E Clean Engine Cooling Fins

2
2

maint_sch-tractore.ROS.e

1, 2
2

Replace Spark Plug
Replace Air Filter Paper Cartridge

Replace Fuel Filter
1 - Change more often when operating under a heavy load or
in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.

LUBRICATION CHART

GENERAL RECOMMENDATIONS

WHEEL
BEARING
ZERK

➁ ENGINE
➀ STEERING

SECTOR GEAR
TETH

➀ MANDREL
ZERKS

02956

BEFORE EACH USE

•

➀ SPINDLE ZERK
➀ FRONT

The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should make
any of the adjustments described in the Service and
Adjustments section of this manual.
• At least once a year you should replace the spark plug,
clean or replace air filter, and check blades and belts
for wear. A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer.
•
•
•
•

3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.

➀ General Purpose Grease
➁ Refer to Maintenance “ENGINE” Section

Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL
SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS.
IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY,
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.

MAINTENANCE
TRACTOR

BLADE CARE
For best results mower blades must be sharp. Replace
worn, bent or damaged blades.

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

CAUTION: Use only a replacement
blade approved by the manufacturer of
your tractor. Using a blade not approved
by the manufacturer of your tractor is hazardous, could damage your tractor and void
your warranty.

If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced. (See “TO CHECK
BRAKE” in the Service and Adjustments section of this
manual).

BLADE REMOVAL (See Fig. 23)

TIRES

•

Raise mower to highest position to allow access to
blades.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
• Remove blade bolt by turning counterclockwise.
• Install new blade with stamped "GRASS SIDE" facing
the ground.
IMPORTANT: To ensure proper assembly, center hole in
blade must align with star on mandrel assembly.
• Install and tighten blade bolt securely (45-55 Ft. Lbs.
torque).
IMPORTANT: Special blade bolt is heat treated.

•

Maintain proper air pressure in all tires (See PSI on
tires).
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.

CENTER
HOLE
BLADE BOLT
(SPECIAL)

CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never operate unless
the operator is in the seat.
ROS "ON" Position

MANDREL
ASSEMBLY

BLADE

STAR

FIG. 23

BATTERY
Your tractor has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary.

Engine "ON" Position
(Normal Operating)

02828

CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
• When the engine is running with the ignition switch in
the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse
should NOT shut off the engine.

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
• Remove terminal guard.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

MAINTENANCE
•
•

TO CHANGE ENGINE OIL (See Figs. 24 and 25)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove yellow cap from end of drain valve and install
the drain tube onto the fitting.

Rinse the battery with plain water and dry.
Clean terminals and battery cable ends with wire brush
until bright.
Coat terminals with grease or petroleum jelly.
Reinstall battery (See “REPLACING BATTERY" in
the SERVICE AND ADJUSTMENTS section of this
manual).

•
•

V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.

OIL DRAIN VALVE

TRANSAXLE COOLING
The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or
steam to clean transaxle.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean cooling fins.

FIG. 25

The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
nearest authorized service center/department.

•
•
•

ENGINE
LUBRICATION

•

Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.

•

SAE VISCOSITY GRADES
SAE 30

•

5W-30

-20
-30

0
-20

30
-10

100

60
10

DRAIN
TUBE

YELLOW CAP

TRANSAXLE PUMP FLUID

46
02

CLOSED
AND
LOCKED
POSITION

Unlock drain valve by pushing inward and turning
counterclockwise.
To open, pull out on the drain valve.
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick. Tighten cap
onto the tube securely when finished.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

FIG. 24

oil_visc_chart1_e

CLEAN AIR SCREEN

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F. Check your engine
oil level more frequently to avoid possible engine damage
from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one
year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.

Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.

AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions. See
Engine Manual.

MAINTENANCE
ENGINE OIL FILTER

CLAMP

Replace the engine oil filter every season or every other
oil change if the tractor is used more than 100 hours in
one year.

MUFFLER

CLAMP

FUEL FILTER

Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or damage.

FIG. 26

CLEANING

SPARK PLUGS

•

Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.

Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 26)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.

SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress brake pedal fully and set parking brake.
• Place attachment clutch in “DISENGAGED” position.
• Turn ignition key to “STOP” and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.

TRACTOR (See Fig. 27)

•

TO REMOVE MOWER

•
•
•

Place attachment clutch in “DISENGAGED” position.
Lower attachment lift lever to its lowest position.
Disengage belt tension rod (K) from lock bracket (L).

•
•

CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and release slowly.
•
•
•

•

From right side of mower, disconnect anti-sway bar (S)
from right rear mower bracket (D) - remove retainer
spring and washer and pull mower toward you until
the bar falls from the hole in bracket.
Turn tractor steering wheel to the left as far as it will
go.
Slide mower out from under right side of tractor.

TO INSTALL MOWER
Follow procedure described in “INSTALL MOWER AND
DRIVE BELT” in the Assembly section of this manual.

Remove mower belt from electric clutch pulley (M).
Disconnect front link (E) from mower - remove retainer
spring and washer.
Go to either side of mower and disconnect mower
suspension arm (A) from chassis and rear lift link (C)
from rear mower bracket (D) - remove retainer springs
and washers.
Go to other side of mower and disconnect the suspension arm and rear lift link.

TO LEVEL MOWER
Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the
appearance of your lawn and lead you to think the mower
is not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 28)
• With all tires properly inflated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
NOTE: As desired, you can raise the low side of mower or
lower the high side.

CAUTION: After rear lift links are disconnected, the attachment lift lever will be
spring loaded. Have a tight grip on lift lever
when changing position of the lever.

B
M

E
H

FIG. 27

SERVICE AND ADJUSTMENTS
•
•

FRONT-TO-BACK ADJUSTMENT (See Figs. 30 and 31)
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting results, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" lower than the
rear tip when the mower is in its highest position.

Go to side of mower you wish to adjust.
With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower the mower, or, to the
right to raise the mower.

CAUTION: Blades are sharp. Protect your
hands with gloves and/or wrap blade with
heavy cloth.

•
•
•
•
•

Turn nut left
to lower mower

Turn nut right
to raise mower
02948

FIG. 28
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
• Test your adjustment by mowing some uncut grass
and visually checking the appearance. Readjust, if
necessary, until you are satisfied with the results.

Raise mower to highest position.
Position any blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear
tip of the blade.
If front tip of blade is not 1/8" to 1/2" lower than the rear
tip, go to the front of tractor.
With an 11/16" or adjustable wrench, loosen jam nut
A several turns to clear adjustment nut B.
With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (tighten) to raise the front of
mower, or, counterclockwise (loosen) to lower the front
mower.
02548

PRECISION SIDE-TO-SIDE ADJUSTMENT
(See Fig. 29)
• With all tires properly inflated, park tractor on level
ground or driveway.

FIG. 30

CAUTION: Blades are sharp. Protect your
hands with gloves and/or wrap blade with
heavy cloth.
•
•

•
•

Raise mower to its highest position.
At both sides of mower, position blade at side and
measure the distance (A) from bottom edge of blade
to the ground. The distance should be the same on
both sides.
If adjustment is necessary, see steps 2 and 3 in Visual
Adjustment instructions above.
Recheck measurements, adjust if necessary until both
sides are equal.

Tighten adjust nut
B to raise mower

02966

Loosen adjust nut
B to lower mower

02950

Loosen jam nut A first

FIG. 31
FIG. 29

NOTE: Each full turn of the adjustment nut will change
mower height about 1/8".
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 1/2" lower than the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.

SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE DRIVE BELT

TO CHECK BRAKE

MOWER DRIVE BELT REMOVAL (See Fig. 32)
• Park tractor on a level surface. Engage parking
brake.
• Lower attachment lift lever to its lowest position.
• Disengage belt tension rod (K) from lock bracket (L).

If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced.
You may also check brake by:
• Park tractor on a level, dry concrete or paved surface,
depress brake pedal all the way down and engage
parking brake.
• Disengage transmission by placing freewheel control
in “transmission disengaged” position. Pull freewheel
control out and into the slot and release so it is held in
the disengaged position.
The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then
the brake needs to be serviced. Contact a qualified service
center.

CAUTION: Belt tension rod is spring
loaded. Have a firm grip on rod and
release slowly.
•

Remove screws (P) from mandrel covers (Q) and remove covers.
Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.
Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S).

•
•

TO REPLACE MOTION DRIVE BELT
(See Fig. 33)

MOWER DRIVE BELT INSTALLATION
• Install belt around all mandrel pulleys (R) and around
idler pulleys (S) as shown.
• Install belt onto electric clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.
• Reassemble mandrel covers (Q). Securely tighten all
screws.
• Engage belt tension rod (K) on locking bracket (L).

Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
• Disconnect clutch wire harness (A).
• Remove anti-rotation link (B) on right side of tractor.
• Remove belt from stationary idler (C) and clutching
idler (D).
• Remove belt from centerspan idler (E).
• Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades (F).
• Remove belt downward from engine pulley and around
electric clutch (G).
• Slide belt toward rear of tractor, off the steering plate
(H) and remove from tractor.

CAUTION: Belt tension rod is spring
loaded. Have a tight grip on rod and
engage slowly.
•

Raise attachment lift lever to highest position.
P
Q

BELT INSTALLATION • Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).
• Pull belt toward front of tractor and roll belt around
electric clutch and onto engine pulley (G).
• Pull belt toward rear of tractor. Carefully work belt down
around transmission cooling fan and onto the input
pulley (F). Be sure belt is inside the belt keeper.
• Install belt on centerspan idler (E).
• Install belt through stationary idler (C) and clutching
idler (D).
• Reinstall anti-rotation link (B) on right side of tractor.
Tighten securely.
• Reconnect clutch harness (A).
• Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
• Install mower (See “TO INSTALL MOWER” in this section of manual).

FIG. 32

SERVICE AND ADJUSTMENTS
WASHERS
RETAINING
RING

AXLE COVER

H
B

SQUARE KEY (REAR
WHEEL ONLY)

A
C

FIG. 34

TO START ENGINE WITH A WEAK BATTERY
(See Fig. 35)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.

F
02953
electric

If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:

FIG. 33

FRONT WHEEL TOE-IN/CAMBER
Your new tractor front wheel toe-in and camber is set at the
factory and is normal. The front wheel toe-in and camber
are not adjustable. If damage has occurred to affect the
factory set front wheel toe-in or camber, contact a qualified
service center.

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START
OTHER VEHICLES.

TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal (C) of fully charged battery.
• Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.

TO REMOVE WHEEL FOR REPAIRS
(See Fig. 34)
•
•

Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not lose).
• Repair tire and reassemble.
• On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.

TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.

WEAK OR DEAD
BATTERY

FULLY CHARGED
BATTERY

FIG. 35

SERVICE AND ADJUSTMENTS
REPLACING BATTERY (See Fig. 36)

TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 37)

WARNING: Do not short battery terminals by allowing
a wrench or any other object to contact both terminals at
the same time. Before connecting battery, remove metal
bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparking from accidental grounding.
• Lift hood to raised position.
• Disconnect BLACK battery cable (A) then RED battery
cable and carefully remove battery from tractor.
• Install new battery with terminals in same position as
old battery.
• First connect RED battery cable (B) to positive (+) battery
terminal with hex bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over terminal.
• Connect BLACK grounding cable to negative (-) battery
terminal with remaining hex bolt and keps nut. Tighten
securely
•

•
•
•
•

Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedure.
HOOD

HEADLIGHT
WIRE
CONNECTOR

Close hood.

02778

A Negative
(Black)
Cable

FIG. 37

ENGINE

TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual.

Positive B
(Red)
Cable

TO ADJUST CHOKE CONTROL

02954

The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engne manual.

FIG. 36

TO REPLACE HEADLIGHT BULB
•
•
•
•

TO ADJUST CARBURETOR

Raise hood.
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.

Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.

STORAGE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.

ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.

WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

TRACTOR

•

Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.

Remove mower from tractor for winter storage. When mower
is to be stored for a period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a clean, dry area.
• Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Maintenance section of this
manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of
this manual).

BATTERY
•
•
•

•
•

CYLINDER(S)

Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.

•
•
•
•

Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).

OTHER
•
•
•
•

Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

Will not start

1.
2.
3.
4.
5.
6.
7.
8.

CORRECTION

Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Weak or dead battery.
Dirty air filter.
Dirty fuel filter.
Water in fuel.

9.
10.

Loose or damaged wiring.
Carburetor out of adjustment.

11.

Engine valves out of adjustment.

1.
2.
3.
4.
5.
6.
7.
8.

Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Recharge or replace battery.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with
fresh gasoline and replace fuel filter.
9. Check all wiring.
10. See “To Adjust Carburetor” in Service Adjust
ments section.
11. Contact an authorized service center/
department.

1.
2.
3.
4.
5.

Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.

6.
7.

Loose or damaged wiring.
Carburetor out of adjustment.

Engine valves out of adjustment.

Engine will not
turn over

1.
2.
3.
4.
5.
6.
7.
8.
9.

Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).

Engine clicks but
will not start

1. Weak or dead battery.
2. Corroded battery terminals.
3. Loose or damaged wiring.
4. Faulty solenoid or starter.

1. Recharge or replace battery.
2. Clean battery terminals.
3. Check all wiring.
4. Check/replace solenoid or starter.

Loss of power

1. Cutting too much grass/too fast.
2. Throttle in “CHOKE” position.
3. Build-up of grass, leaves and trash under mower.
4. Dirty air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
7. Dirty fuel filter.
8. Stale or dirty fuel.

1.
2.
3.
4.
5.
6.
7.
8.

Hard to start

Excessive vibration

1. Clean/replace air filter.
2. Replace spark plug.
3. Recharge or replace battery.
4. Replace fuel filter.
5. Empty fuel tank and refill tank with fresh, clean
gasoline.
6. Check all wiring.
7. See “To Adjust Carburetor” in Service Adjust
ments section.
8. Contact an authorized service center/
department.

Water in fuel.

1.
2.
3.
4.
5.
6.
7.
8.
9.

10.
11.
12.
13.
14.

Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.

10.
11.
12.
13.
14.

15.

Engine valves out of adjustment.

15.

1. Worn, bent or loose blade.
2. Bent blade mandrel.
3. Loose/damaged part(s).

Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/
department.

Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean
gasoline.
Empty fuel tank and carburetor, refill tank with
fresh gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjust
ments section.
Contact an authorized service center/
department.

1. Replace blade. Tighten blade bolt.
2. Replace blade mandrel.
3. Tighten loose part(s). Replace damaged parts.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

Engine dies when
tractor is shifted
into reverse

Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.

Turn ignition key to
ROS "ON" position.
See Operation section.

Engine continues to
run when operator
leaves seat with
attachment clutch
engaged

Faulty operator-safety presence control system.

Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.

Poor cut - uneven

1.
2.
3.
4.
5.

Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1. Replace blade. Tighten blade bolt.
2. Level mower deck.
3. Clean underside of mower housing.
4. Replace blade mandrel.
5. Clean around mandrels to open vent holes.

Mower blades will not
rotate

1. Obstruction in clutch mechanism.
2. Worn/damaged mower drive belt.
3. Frozen idler pulley.
4. Frozen blade mandrel.

Poor grass discharge

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

CORRECTION

1. Remove obstruction.
2. Replace mower drive belt.
3. Replace idler pulley.
4. Replace blade mandrel.

Engine speed too slow.
1.
Travel speed too fast.
2.
Wet grass.
3.
Mower deck not level.
4.
Low/uneven tire air pressure.
5.
Worn, bent or loose blade.
6.
Buildup of grass, leaves and trash under mower. 7.
Mower drive belt worn.
8.
Blades improperly installed.
9.
Improper blades used.
10.
Clogged mower deck vent holes from buildup of 11.
grass, leaves, and trash around mandrels.

Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.

Headlight(s) not
working
(if so equipped)

1. Light switch is “OFF”.
2. Bulb(s) or lamp(s) burned out.
3. Faulty light switch.
4. Loose or damaged wiring.
5. Blown fuse.

1. Turn light switch “ON”.
2. Replace bulb(s) or lamp(s).
3. Check/replace light switch.
4. Check wiring and connections.
5. Replace fuse.

Battery will not charge

1. Bad battery cell(s).
2. Poor cable connections.
3. Faulty regulator (if so equipped).
4. Faulty alternator.

1. Replace battery.
2. Check/clean all connections.
3. Replace regulator.
4. Replace alternator.

Loss of drive

1. Freewheel control in “disengaged” position.
2. Motion drive belt worn, damaged, or broken.
3. Air trapped in transmission during shipment
or servicing.

1. Place freewheel control in “engaged” position.
2. Replace motion drive belt.
3. Purge transmission.

Engine “backfires”
when turning
engine “OFF”

1. Engine throttle control not set between half and 1. Move throttle control between half and full speed
full speed (fast) position before stopping engine.
(fast) position before stopping engine.

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

SCHEMATIC

02929-194276_Regulated-Tex

BATTERY
RED

SOLENOID

STARTER

RED

FUSE

BLACK

ELECTRIC CLUTCH
WHITE

WHITE

BLACK

WHITE

G
L

GRAY

A2
RED

CLUTCH/BRAKE
(PEDAL UP)

RED

BLACK
BLACK

PTO SWITCH
(DISENGAGED)

REVERSE SWITCH
(NOT IN REVERSE)

BLACK
BLACK

BLACK

BLACK
BLACK

1
6

SEAT SWITCH
(NOT OCCUPIED)

GRAY

BLACK /WHITE

JUNCTION
CONNECTOR

SHORTING
CONNECTOR

CHASSIS
HARNESS

SPARK
PLUGS GAP
(2 PLUGS ON
TWIN CYL. ENGINES)

IGNITION
UNIT

(OPTIONAL)
HOUR
METER

BLACK

BLUE

BLACK

FUEL
LINE

12V
POWER OUTLET
(IF SO EQUIPPED)

BLUE

CHARGING SYSTEM OUTPUT
16 AMP DC @ 36 RPM

FUEL SHUT-OFF
SOLENOID
(IF SO EQUIPPED)

REGULATOR

ORANGE

RED

STATOR

28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)
BROWN

BLACK

LIGHT
SWITCH
HEADLIGHTS

2
1

IGNITION SWITCH
POSITION

CIRCUIT

OFF
RUN/OVERRIDE

M+G+A1
B+A1

RUN
START

B+A1
B + S + A1

“MAKE”

L+A2

02929

CHASSIS HARNESS
CONNECTOR
(MATING SIDE)

DASH HARNESS
CONNECTOR
(MATING SIDE)

WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED
CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY
SHOULD BE REPLACED TO
PROPERLY SECURE YOUR
WIRING.

NON-REMOVABLE
CONNECTIONS

REMOVABLE
CONNECTIONS

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

ELECTRICAL

90
21

41
24

101

40
27

33
30

25
34

103

59
46
2

100
8

71
tter

28
y_

102

55
28

194276D

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

ELECTRICAL

KEY
NO.
1
2
8
16
21
22
24
25
26
27
28
29
30
33
34
40
41
42
43
46
50
55
59
71
90
91
99
100
101
102
103

PART
NO.
532 14 49-27
874 76 04-12
532 18 64-91
532 17 61-38
532 18 37-59
532 00 41-52
532 40 02-53
532 19 88-93
532 17 51-58
873 51 04-00
532 14 54-91
532 40 15-45
532 19 33-50
532 14 04-01
532 11 07-12
532 40 11-04
817 72 04-08
532 13 15-63
532 19 25-07
532 40 17-63
532 17 46-51
817 49 05-12
532 40 03-03
532 19 42-76
532 40 07-24
532 19 02-70
817 67 04-12
819 09 14-16
532 19 83-17
532 40 44-54
532 40 79-62

DESCRIPTION
Battery
Bolt Hex Hd 1/4-20 unc x 3/4
Battery Box
Switch Interlock
Harness Socket Light
Bulb, Light # 1156
Cable Battery
Cable Starter
Fuse
Nut Keps Hex 1/4-20 unc
Cable Ground 21" Blk 6 Ga.
Switch Seat
Switch Ign
Key Ign Molded Generic
Switch Light/Reset
Harness Ign. Dash
Screw Thd Cut 1/4-20 x 1/2
Cover Terminal Red
Solenoid
Gauge Hourmeter
Switch PTO
Screw Thdrol 5/16-18 x 3/4
Outlet 12-Volt
Harness Ign
Cover Terminal Battery
Strap Battery
Screw Hexwsh Thdrol 1/4-20 x 3/4
Washer 9/32 x 7/8 x 16 Ga.
Pigtail MATNLK
Harness Pigtail K46 Tex ROS
Harness Pigtail 12V Outlet

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

CHASSIS

238

234

137

234

CHASSIS
TEX?
GT
HUSQ

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

CHASSIS

KEY
NO.

PART
NO.

DESCRIPTION

3
5
14
15
18
25
34
37
52
58
68
99
102
130
137
139
150
152
156
161
162
165
175
176
177
178
180
181
182

532 40 50-12
532 40 87-01
532 41 10-46
532 19 89-07
532 40 86-07
532 19 89-06
532 19 61-25
532 40 18-25
873 68-05-00
532 19 43-14
817 49 05-08
532 40 59-17
532 12 47-88
532 19 16-11
532 40 75-90
817 49 05-08
532 19 85-12
532 19 95-35
817 06 05-12
532 40 18-26
532 14 24-32
532 19 68-26
532 19 63-04
532 19 32-32
532 19 52-27
532 19 97-82
532 40 15-59
532 40 30-25
532 19 47-87

Logo
Dash
Hood
Lens LH
Grille
Lens RH
Plate Engine
Fender
Nut Crown Lock 5/16-18
Bracket Fender
Screw 5/16-18 x 1/2
Rod Bypass Asm.
Retainer Spring 1"
Screw 10 x 3/4 Single Lead Hex
Bumper Dash
Screw 5/16-18 x 1/2
Duct Heat Hood
Shield Browning/Debris
Screw 5/16-18 x 3/4
Console Fuel Window
Screw Hex Wsh Hi-Lo 1/4 x 1/2
Bracket Support Tank
Crossmember
Screw 10-24 x 5/8 Wshd Qdrx
Bushing Steering
Cargo Asm. Net
Chassis
Bushing Mtg. Fender Crgo.
Dash Lower

KEY
NO.

PART
NO.

DESCRIPTION

183
189
194
196
199
202
203
204
205
206
207
208
209
210
211
212
213
214
217
218
219
221
234
235
236
238
239

873 47 85-20
817 00 05-12
873 80 05-00
532 40 02-99
532 19 82-59
532 40 30-48
532 40 30-76
532 19 89-04
532 40 17-09
532 40 17-11
532 19 71-98
532 19 71-99
532 19 91-30
532 19 91-31
532 19 91-32
532 19 91-33
874 76 05-12
532 19 91-45
532 15 65-24
532 19 63-95
532 19 51-61
532 19 89-09
532 40 47-42
532 40 61-29
873 93 05-00
532 40 86-06
532 11 04-52

Bolt 5/16-18 UNC x 1-1/4
Screw 5/16-18 x 3/4
Nut Lock Hex Flange 5/16-18
Console Asm. Deck Lift
Plate Deck Lift
Vent Side Hood RH
Vent Side Hood LH
Vent Asm Hood Top
Skirt Hood Side RH
Skirt Hood Side LH
Bezel RH
Bezel LH
Insert Hex Top RH
Insert Hex Top LH
Insert Hex Bottom RH
Insert Hex Bottom LH
Bolt Hex Hd 5/16-18 unc x 3/4
Clip Retainer
Rod Pivot
Hood Stop
Stud Fastener
Reflector LH
Bumper Hood
Spacer Fender
Nut Center Lock 5/16-18 UNC
Trim
Nut Push

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

DRIVE

74
221

220

213

74
125
206
26
207

209
92
143

218
197

116

216

196

219
171

221 184
42

125
35
80

125

125
125
160

167
160

170

188

185

226

51
186
189

153
49

187

161

211

51
15

215

159

211
166

51
17
9

116
2

153

125

183

225
162

205

116
162
230
2
1

230

169
drive-tex_31-Husq TuffTorq

222

163

214
210

159

190

208 125

169

183

7
205
33

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

DRIVE

KEY
NO.

PART
NO.

1
2
7
9
15
17
26
29
33
35
42
49
50
51
52
56
64
70
74
80
96
116
125
143
153
159
160
161
162
163
166
167
169
170
171

532 41 40-06
532 18 62-11
532 19 98-44
532 14 00-80
819 13 13-16
532 41 36-78
532 19 96-79
532 40 38-06
812 00 00-01
532 19 95-91
532 12 48-72
872 11 06-14
532 19 43-27
873 90 06-00
532 19 43-26
532 13 09-69
532 19 78-65
532 40 05-30
532 14 24-32
532 40 44-83
874 76 05-20
873 90 05-00
817 00 05-12
817 49 05-08
532 12 47-88
876 02 04-12
532 16 94-84
532 19 54-03
532 19 57-85
532 40 10-34
532 19 72-90
532 40 52-57
874 49 05-60
532 19 43-22
872 11 06-16

DESCRIPTION
Transaxle, TUFFTORQ K46BN
Key 1/4 x 2.5
Hub Asm. Wheel
Bolt Hub Wheel
Washer 13/32 x 13/16 x 16 Ga.
Spring, Brake
Spring Return Cruise
Rod, Brake
Ring E
Rod, Brake, Park
Cover, Foot Pedal
Bolt
Pulley Idler Flat
Lock Nut 3/8-16
Idler V-Groove 910" Offset
V-Belt, Drive
Shaft Asm. Pedal Brake Control
Control Asm.
Screw 1/4 x 1/2
Strap Torque
Bolt Fin Hex 5/16-18 unc x 1.25
Nut Lock Hex Flange 5/16-18
Screw 5/16-18 x 3/4
Screw Thdrol 5/16-18 x 1/2
Retainer Spring
Pin Cotter 1/8 x 3/4
Retainer Clip
Spring, Return, Clutch
Spacer Transaxle
Rod Pedal Control
Nut Push .625
Latch Brake Parking
Bolt Hex Flghd 5/16-18 x 3.75
Keeper Belt Centerspan
Bolt RDHD SQNK 3/8-16UNC x 2

KEY
NO.

PART
NO.

183
184
185
186
187
188
189
190
196
197
205
206
207
208
209
210
211
213
214
215
216
218
219
220
221
222
225
226
230

532 40 04-24
532 40 31-18
872 11 06-20
532 19 43-21
819 13 32-10
532 19 43-23
532 19 43-17
532 19 43-18
817 00 06-16
532 19 97-69
532 12 17-48
532 19 78-67
532 19 78-68
532 19 78-69
532 19 95-92
532 19 78-60
532 12 01-83
532 40 31-19
532 40 17-22
532 40 17-23
532 19 61-31
874 78 05-20
873 93 05-00
532 19 89-08
532 40 31-87
819 21 20-10
532 40 33-19
532 40 08-31
532 18 89-67

DESCRIPTION
Spacer Split
Handle Parking Brake
Bolt Rdhd Sqnk 3/8-16 x 2-1/2
Spacer Retainer
Washer
Link Clutch Ground Drive
Bellcrank Ground Drive
Keeper Bellcrank Ground Drive
Screw 3/8-16 x 1
Bracket Clutch Anti-Rotation
Washer
Bracket Mount Latch Cruise
Latch Control Cruise
Gear Sector Control Cruise
Rod Control Cruise
Rocker Asm. Pedal Control
Bearing Nylon
Knob Control Cruise
Pedal Forward
Pedal Reverse
Bracket Pulley Idler
Bolt Fin Hex 5/16-18 unc x 1-1/4
Nut Center Lock 5/16-18 UNC
Reflector RH
Retainer Spring Clip Handle
Washer 21/32 x 1-1/4 x 10 Ga.
Keeper Belt Trans.
Bracket Mount Touque
Washer

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

ENGINE

21
62

20
18
45

79
11

91
28
41
42

31
37

9
29

SPARK ARRESTER KIT

engine-tex_7-vgt

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

ENGINE

KEY
NO.
1
2
9
11
12
15
18
20
21
22
28
29
31
37
41
42
45
62
69
70

PART
NO.
-----532 14 97-23
532 19 43-20
532 17 93-35
532 19 43-43
532 19 34-99
532 19 42-67
532 17 83-85
532 19 16-11
532 19 15-96
532 40 11-35
532 13 71-80
532 14 50-06
532 12 34-87
532 12 61-97
810 04 07-00
873 51 04-00
532 14 66-29
532 16 53-91
532 15 99-55

KEY
NO.
71
79
81
82
84
85
87
90
91

DESCRIPTION
Engine Briggs Model No. 445877
Muffler
Keeper Belt Engine
Clutch Electric
Pulley Engine
Tank Fuel 4.0
Cap Asm
Control Throttle
Screw 10 x 3/4 Single Lead Hex
Control Choke
Fuel Line
Spark Arrester Kit
Clip Push-In
Clamp Hose
Washer 1-1/2 OD x 15/32 ID x .250
Washer Lock 7/16
Nut Keps Hex 1/4-20 unc
Shield Heat Muffler
Gasket
Tube Exhaust LH

PART
NO.
532 16 05-89
532 18 39-06
532 14 84-56
532 18 16-54
817 06 06-20
532 17 99-53
532 19 82-39
817 00 06-16
532 18 74-95

DESCRIPTION
Tube Exhaust RH
Screw Socket Head 5/16-18 x 1
Tube Drain Oil Easy
Plug Drain Oil
Screw 3/8-16 x 1-1/4
Bolt Hex 7/16-20 x 3.75 Gr. 5
Bolt 5/16-18 unc x 1 w/Sems
Screw 3/8-16 x 1
Bushing

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
For engine service and replacement parts, call the toll free
number for your engine manufacturer listed below:
Briggs & Stratton
1-800-233-3723
Kohler Co.
1-800-544-2444
Tecumseh Products
1-800-558-5402
Honda Engines
1-800-426-7701
Kawasaki
1-949-460-5688

ENGINE POWER RATING INFORMATION
The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and
corrected in accordance with SAE J1995 (Revision 2002-5). Actual gross engine power will be lower and is affected by,
among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the
gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or
net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this Series engine.

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

STEERING ASSEMBLY

45
51

63
19

60
57

61
8

67
2

98
7

6
4

35
58

28
13

15
22

69
68

13
14
15

53 8

70
steering-tex_4-husq

KEY
NO.

PART
NO.

DESCRIPTION

1
2
4
5
6
7
8
9
13
14
15
16
19
21
22
26
28
35
45

532 19 39-43
532 19 59-68
532 40 30-89
532 40 30-90
532 12 49-31
532 12 17-48
812 00 00-29
532 12 12-32
532 12 17-49
810 04 06-00
873 54 06-00
532 40 82-19
532 19 47-29
532 18 67-37
532 19 48-45
532 19 36-52
817 00 06-12
532 19 47-32
819 18 38-12

Wheel, Steering
Axle Asm., Front
Spindle Asm., LH
Spindle Asm., RH
Bearing, Race Thrust Harden
Washer 25/32 x 1-5/8 x 16 Ga.
Ring, Klip #T5304-75
Cap, Spindle
Washer 25/32 x 1-1/4 x 16 Ga.
Washer, Lock Hvy Hlcl Spr 3/8
Nut, Crown Lock 3/8-24 unf
Shaft Steering
Plate Steering
Adapter, Wheel Steering
Bushing, Strg. Blk
Insert, Wheel Steering
Screw 3/8-16 x 3/4
Gear, Sector Plate
Washer 9/16 x 2-3/8 x 12 Ga.

KEY
NO.

PART
NO.

51
53

873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf
532 18 89-67 Washer Hardened .793 x 1.637 x
.060
532 19 72-46 Bracket Upstop
532 19 47-47 Bolt Shoulder Sector Pivot CFM
532 19 47-48 Washer Thrust Sector Steering
873 97 10-00 Nut Flange Lock 5/8-11
532 19 47-40 Draglink LH
532 19 47-41 Draglink, RH
817 00 05-12 Screw 5/16-18 x 3/4
532 19 98-49 Retainer Clip Spring Steering
871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr
532 19 47-37 Bushing PM Front Axle
873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5
532 19 91-62 Washer 1.5 x .505 x .118
532 19 61-97 Bracket Deck Susp. Front

57
58
59
60
61
62
63
64
66
67
68
69
70

DESCRIPTION

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

SEAT ASSEMBLY

8
8
7
7
41
40

37
37
2

44
43

seat-tex_7-vgt

KEY
NO.

PART
NO.

DESCRIPTION

1
2
3
6
7
8
10
21

532 40 66-21
532 18 01-66
532 14 06-75
873 80 06-00
532 12 41-81
532 17 18-77
532 19 69-77
532 17 18-52

Seat
Bracket Pivot Fender
Strap, Asm Fender
Nut, Lock W/Ins. 3/8-16 unc
Spring, Seat Cprsn
Bolt 5/16-18 uncx 3/4 w/Sems
Pan, Seat
Bolt, Shoulder 5/16-18

KEY
NO.

PART
NO.

DESCRIPTION

37
40
41
43
44

873 80 05-00
532 19 76-61
532 19 82-00
874 76 06-12
819 13 38-12

Nut, Lock 5/16-18 unc
Handle Slide Seat
Spring Latch Seat
Bolt 3/8-16 x 3/4
Washer 13/32 x 2-3/8 x 12 Ga.

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

MOWER DECK

47
185

39
34
192
49

21
122

52
7

114
43
196

116
117

120
29

113
194

12
16

26
24

19
27

21
21

60
59

190

189

190
11

187

188
8

187

mower_deck 54-tex_3

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

MOWER DECK

KEY
NO.

PART
NO.

DESCRIPTION

1
6
7
8
11
-12
13
14
16
15
18
19
21
24
25
26
27
29
30
31
32
33
34
39
43
46
47
49

532 40 31-25
532 19 60-66
532 19 71-81
532 17 43-65
532 18 72-56
532 18 72-54
532 40 48-51
532 18 72-91
532 18 72-81
819 13 13-12
532 11 04-85
872 14 05-05
532 19 42-08
873 68 05-00
532 10 53-04
532 17 81-02
532 11 04-52
532 18 89-38
532 13 14-91
532 17 39-84
532 18 76-90
532 17 34-36
532 40 02-34
873 68 06-00
532 19 61-04
532 19 60-65
532 13 77-29
532 19 61-03
873 90 06-00

Deck Weldment Mower
Cover Mandrel LH
Cover Mandrel RH
Bolt 7/16 Asm. Blade
Blade Bagging
Blade Discharge
Rod Anti Sway
Shaft Asm. w/Lower Bearing
Housing, Mandrel
Washer 3/8
Bearing, Ball, Mandrel
Bolt Carriage 5/16-18 x 5/8
Pin Cotter 5/16 Bowtie
Nut, Crownlock 5/16-18 unc
Cap Sleeve
Spring, Torsion
Nut, Push
Deflector Shield
Rod, Hinge
Screw, Thdroll Washer Head
Washer, Spacer Mower Vented
Pulley, Mandrel
Nut, Flg. Top Lock
Nut Crownlock 3/8-16 unc
Pulley, Idler, Stationary LH
Arm, Idler
Screw, Thdroll. 1/4-20 x 5/8
Belt Deck Drive
Nut, Lock Flg. 3/8-16 unc

KEY
NO.

PART
NO.

50
52
58
59
60
97
98
113
114
116
117
120
122
185
187
188
189
190
192
194
196
--

872 11 06-16
532 19 61-06
532 18 73-42
532 18 73-44
532 18 76-07
532 17 85-15
532 19 61-05
872 11 05-08
532 18 75-56
532 19 34-06
532 17 48-73
819 13 20-12
532 18 75-57
873 90 07-00
532 19 51-61
873 90 05-00
532 19 51-85
532 19 65-39
532 19 84-68
872 14 07-16
872 14 06-20
532 18 72-92

DESCRIPTION

Bolt Rdhd Sqnk 3/8-16 unc x 2
Pulley Idler
Baffle Right
Baffle Left
Baffle Center
Washer Hardened
Spring Drive
Bolt Rdhd Sqnk 5/16-18 x 3/4
Rod Tension Relief
Bolt, Shoulder
Gauge Wheel
Washer 13/32 x 1-1/4 x 12 Ga.
Bushing Tension Relief
Nut Lock Flange 7/16-14 Gr. 5
Stud Fastener w/"D" Anti-Rotation
Nut Lock Hex Flange
Arm Susp. Mower Rear
Bolt Shoulder
Keeper Belt Idler
Bolt Carr Sqnk 7/16-24 x 2
Bolt Rdhd 3/8-16 x 2-1/2 Gr. 5
Mandrel Asm. Service (Includes
Key Nos. 13-15 and 33)
532 19 93-00 Replacement Mower, Complete

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

DECALS

4
16

14
14

3
8

6
5

KEY
NO.
1
2
3
4
5
6
8
9

PART
NO.
532 40 21-04
532 40 21-28
532 17 05-63
532 18 09-41
532 17 85-02
532 40 88-43
532 19 87-85
532 14 50-05

DESCRIPTION
Decal, Operator's
Decal, Hood Insert
Decal, Warning
Decal, Hood Cust Resp
Decal, Caution
Decal, Eng. HP
Decal, Mower Sch.
Decal, Battery Dnge/Poi

WHEELS AND TIRES
1
2

11 3
4
7

10
5

9
8

KEY
NO.
13
14
16
17
------

PART
NO.
532 40 44-84
532 41 01-09
532 40 28-32
532 41 06-29
532 16 69-60
532 40 17-71
532 40 37-73
532 41 07-08
532 41 07-09

DESCRIPTION
Decal, Steering Whl
Decal, Panel Side
Decal, Hood Logo
Decal, Replacement
Decal, Bypass
Pad, Footrest, LH
Pad, Footrest, RH
Manual, Owner's (Eng)
Manual, Owner's (Fr)

KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
--

PART
NO.
532 05 91-92
532 06 51-39
532 14 45-09
532 05 99-04
532 10 62-30
532 12 49-57
532 12 49-59
532 17 50-39
532 18 47-08
532 12 49-26
532 40 17-82
532 14 43-34

DESCRIPTION
Cap, Valve, Tire
Stem, Valve
Rim Assembly, Front
Tube, Front (Service Item Only)
Tire, Front
Fitting, Grease (Front Wheel Only)
Bearing, Flange (Front Wheel Only)
Cap, Axle (Front Wheel Only)
Tire, Rear
Tube, Rear (Service Item Only)
Rim Assembly, Rear
Sealant, Tire (10 oz. Tube)

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

wheel_art_1-tex

TRACTOR - MODEL NO. LGT2654 (96043003600), PRODUCT NO. 960 43 00-36

MOWER LIFT
7

87
87

89
3
10

88
97
2

91
87

lift-tex_3

89
87

KEY
NO.

PART
NO.

DESCRIPTION

2
3
7
10
87
88
89

532 19 52-23
532 19 52-30
532 41 15-55
532 19 63-14
532 19 42-09
532 19 53-04
819 19 19-12

Shaft Asm., Lift
Lever Asm., Lift Rh
Grip, Lever
Spring Torsion
Pin Cotter 7/16 Bow Tie Lock
Spring Lift Assist
Washer Clear Zinc

KEY
NO.

PART
NO.

DESCRIPTION

90
91
97
98

532 19 42-08
532 40 34-07
817 06 06-12
532 19 52-64

Pin Cotter 5/16 Bow Tie Lock
Link Lift Susp Mower Rear
Screw 3/8-16 x .75 Smgml Tap/R.Z
Link Lift Susp. Front Mower

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

SECTION 4: EXCEPTIONS AND LIMITATIONS

The following items are not covered by this warranty:
(1)Normal customer maintenance items which become worn through normal regular use, including, but not
limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain,
spark plugs, starter ropes and tines;
(2)Natural discoloration of material due to ultraviolet light;
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective
manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer;
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations
which are manufactured by third party engine manufacturer.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component fails
because of a defect in material or workmanship during the warranty period.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY

30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for
defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must
be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be followed
as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under
warranty.

90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners,
snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any Husqvarna
product used for commercial, institutional, professional, or income producing purposes or use except as otherwise provided herein.

Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.

1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering
trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems
used for commercial, institutional, professional or income producing purposes or use.

Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except
for those components which are part of engine systems manufactured by third party engine manufacturers for
which the purchaser has received a separate warranty with product information supplied at time of purchase.

2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk
behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers,
backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial,
nonprofessional, noninstitutional or nonincome producing use, except as herein stated.

2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks,
and ground engaging commercial equipment.

3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)

Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser
to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the
product as set forth below:
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held
product.

SECTION 1: LIMITED WARRANTY

HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269

531 83 81-23

2002

To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address
of the selling dealer.

It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly
filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10)
days from the date of purchase in order to confirm the warranty and to facilitate post-sale service.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION

The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure
occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation.
Proof of purchase, as explained in section 6, rests solely with the customer.

SECTION 5: CUSTOMER RESPONSIBILITIES

Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN
DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT.
HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT
WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY M A N U F A C TURED PRODUCTS.

This warranty shall be inapplicable to defects resulting from the following:
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,
corrosion, or any adverse reaction due to incorrect storage or use habits;
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna;
(3)Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable
laws; or:
(4)Additional damage to parts or components due to continued use occurring after any of the above.

WARRANTY STATEMENT

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

FOL
DA
L
O
NG D
THIS
O
I
T
S
T
A
E
D LIN
1
5
DEG
E
RE
E
S
LOP
E

ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL

15 DEGREES MAX.

WARNING: To avoid serious injury, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.

SERVICE NOTES

532 41 07-08 Rev. 2 05.17.07 AP

Printed in U.S.A.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Create Date                     : 2012:05:12 17:41:17Z
Keywords                        : manuals, instruction manuals, user manuals, service manuals, user guides, pdf manuals, owners manuals, installation guides
Modify Date                     : 2014:12:07 15:14:52+08:00
Subject                         : Search through 700.000 manuals online & and download pdf manuals.
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Provided By MANUALSLIB.COM - http://www.manualslib.com/
Description                     : Search through 700.000 manuals online & and download pdf manuals.
Title                           : ManualsLib - Makes it easy to find manuals online!
Creator Tool                    : pdftk 1.44 - www.pdftk.com
Metadata Date                   : 2014:12:07 15:14:52+08:00
Producer                        : itext-paulo-155 (itextpdf.sf.net-lowagie.com)
Document ID                     : uuid:9e246c35-4f28-734a-b5ca-cebe4bc4c80a
Instance ID                     : uuid:a122f9d4-1b22-bd44-83d1-ee41712a0591
Page Count                      : 48

EXIF Metadata provided by EXIF.tools

Husqvarna Lgt2654 Owners Manual ManualsLib Makes It Easy To Find Manuals Online!

Navigation menu

Versions of this User Manual:

Views

Navigation