Husqvarna Ride On Mower Lth1742Twin Users Manual OM, LTH1742 Twin, 96041006700, 2007 11

2015-01-24

: Husqvarna Husqvarna-Ride-On-Mower-Lth1742Twin-Users-Manual-317850 husqvarna-ride-on-mower-lth1742twin-users-manual-317850 husqvarna pdf

Open the PDF directly: View PDF PDF.
Page Count: 32

DownloadHusqvarna Husqvarna-Ride-On-Mower-Lth1742Twin-Users-Manual- OM, LTH1742 Twin, 96041006700, 2007-11  Husqvarna-ride-on-mower-lth1742twin-users-manual
Open PDF In BrowserView PDF
03002

LTH1742TWIN
Operator's Manual

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

•
WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.

•
•
•

WARNING: Do not coast down a hill
in neutral, you may lose control of the
tractor.

•
•

WARNING: Tow only the attachments
that are recommended by and comply with specifications of the manufacturer of your tractor. Use common
sense when towing. Operate only at
the lowest possible speed when on a
slope. Too heavy of a load, while on
a slope, is dangerous. Tires can lose
traction with the ground and cause you
to lose control of your tractor.

•

•
•

I. GENERAL OPERATION

•
•
•
•

•
•
•
•

•
•
•

Read, understand, and follow all instructions on the
machine and in the manual before starting.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the
blades when crossing gravel surfaces.
Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.

Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.

II. SLOPE OPERATION
Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
• Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot
on the ground.
• Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.

2

SAFETY RULES
Safe Operation Practices for Ride-On Mowers
III. CHILDREN

GENERAL SERVICE
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing.
• If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine
running.
• Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service
as required.
• Maintain or replace safety and instruction labels, as
necessary.

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the
area.
• Before and while backing, look behind and down for
small children.
• Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.

IV. TOWING
•
•
•
•
•

Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.

•
•
•

V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
• Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.

•

•
•
•
•
•
•
•
•
•

3

Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Be alert and turn machine off if a child enters the
area.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

PRODUCT SPECIFICATIONS
Gasoline Capacity
and type:

1.5 Gallons
Unleaded Regular

Oil Type (API-SG-SL):

SAE 10W-30 (above 32°F)
SAE 5W-30 (below 32°F)

Oil Capacity:

W/Filter:

Spark Plug:

Champion RCJ8Y
(Gap: .030")

Ground Speed (MPH):

Forward:
Reverse:

Charging System:

14 Amps

Battery:

AMP/HR:
MIN. CCA:
CASE SIZE:

Blade Bolt Torque:

45-55 FT. LBS.

CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/
department. We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.

60.8 oz

5.5
2.4

CUSTOMER RESPONSIBILITIES

35
280
U1R

•
•
•

Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.

WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
A spark arrester for the muffler is available through your
nearest authorized service center/department.

TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY ................................................................. 6-8
OPERATION ............................................................. 9-14

MAINTENANCE SCHEDULE ...................................... 15
MAINTENANCE ..................................................... 15-18
SERVICE AND ADJUSTMENTS ............................ 19-24
STORAGE .................................................................... 25
TROUBLESHOOTING ............................................ 26-27

4

UNASSEMBLED PARTS
Steering Wheel

Steering
Wheel Insert

(1) 5/16
Lock Washer

(1) Large
Flat Washer

Steering Wheel
Adapter

Steering
Boot

(1) Hex Bolt

Steering
Extension
Shaft

Seat
(1) Washer

(1) Hex Bolt

(1) Seat

(1) Oil Drain Tube
For Future Use

Keys

Slope Sheet
(1) Hood Scoop

(2) Keys

5

ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 3/4" wrench
Pliers
(2) 7/16" wrenches
Tire pressure gauge
Utility knife

INSERT
HEX BOLT
LOCK WASHER
LARGE FLAT
WASHER

When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).

STEERING
WHEEL

TO REMOVE TRACTOR FROM
CARTON
UNPACK CARTON
•

•
•

Remove all accessible loose parts and parts cartons
from carton.
Cut along dashed lines on all four panels of carton.
Remove end panels and lay side panels flat.
Check for any additional loose parts or cartons and
remove.

STEERING BOOT

ADAPTER

BEFORE REMOVING TRACTOR FROM
SKID

EXTENSION
SHAFT

ATTACH STEERING WHEEL (See Fig. 1)

LOWER
STEERING
SHAFT

ASSEMBLE EXTENSION SHAFT AND BOOT
• Slide extension shaft onto lower steering shaft.
• Place tabs of steering boot over tab slots in dash and
push down to secure.
INSTALL STEERING WHEEL
• Position front wheels of the tractor so they are pointing
straight forward.
• Remove steering wheel adapter from steering wheel
and slide adapter onto steering shaft extension.
• Position steering wheel so cross bars are horizontal
(left to right) and slide inside boot and onto adapter.
• Assemble large flat washer, 5/16 lock washer, 5/16 hex
bolt and tighten securely.
• Snap steering wheel insert into center of steering
wheel.
• Remove protective materials from tractor hood and
grill.

FIG. 1

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN
SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO
ROLL OFF SKID.

6

ASSEMBLY
INSTALL SEAT (See Figs. 2a and 2b)
•

•
•

SEAT PAN

Remove bolt and flat washer securing seat to cardboard
packing and set aside for assembly of seat to tractor.
Remove the cardboard packing and discard.
Connect switch to seat.
Place seat on seat pan so all three (3) bottom pads
are positioned over large slotted holes in pan.

LABEL
BATTERY
BOX DOOR
TERMINAL

TERMINAL
SEAT
SWITCH
02021

PAD

FIG. 3a

ATTACH HOOD SCOOP (See Fig. 3b)

SLOT
SEAT
PAN
TAPE
WIRING HARNESS

FIG. 2a
Push down on seat to engage pads in slots and pull
seat towards rear of tractor.
• Raise seat and tighten bolt securely.
• Remove tape and discard.
• Lower seat into operating position and sit on seat.
Press clutch/brake pedal all the way down. If operating
position is not comfortable, adjust seat.
To adjust seat: Grasp adjustment handle and pull up, slide
seat to desired position and release adjustment handle.
•

TAPE

SLOT
PAD
FLAT
WASHER

SEAT PAN
BOLT

ADJUSTMENT
HANDLE

TAB

FIG. 2b

CHECK BATTERY (See Fig. 3a)
•
•

Lift seat pan to raised position and open battery box
door.
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10
amps.
Fig. 3b

7

ASSEMBLY
NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.

CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.

WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.

CHECK BRAKE SYSTEM

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of
controls)
•
•
•

•
•

After you learn how to operate your tractor, check to see that
the brake is operating properly. See “TO CHECK BRAKE”
in the Service and Adjustments section of this manual.

Raise attachment lift lever to its highest position.
Release parking brake by depressing brake pedal.
Place freewheel control in "transmission disengaged
position" (See “TO TRANSPORT” in the Operation
section of this manual).
Roll tractor forward off skid.
Remove banding holding the deflector shield up against
tractor.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BEST
PERFORMANCE AND SATISFACTION FROM THIS
QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓ All assembly instructions have been completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and charged.
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓ Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓ Check wiring. See that all connections are still secure
and wires are properly clamped.
✓ Before driving tractor, be sure freewheel control is in
“transmission engaged” position (see “TO TRANSPORT” in the Operation section of this manual).
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓ Become familiar with all controls, their location and
function. Operate them before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
✓ It is important to purge the transmission before operating your tractor for the first time. Follow proper
starting and transmission purging instructions (See
“TO START ENGINE” and “PURGE TRANSMISSION”
in the Operation section of this manual).

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of
controls)
•
•
•
•
•
•

•
•
•
•

Be sure all the above assembly steps have been completed.
Check engine oil level and fill fuel tank with gasoline.
Place freewheel control in "transmission engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
Sit on seat in operating position, depress brake pedal
and set the parking brake.
Raise attachment lift lever to its highest position.
Remove key from bag and start the engine (see "TO
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
Release parking brake.
Slowly depress forward drive pedal and drive tractor
off skid.
Apply brake to stop tractor and set parking brake.
Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.

8

OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

REVERSE

ENGINE OFF

LIGHTS ON

NEUTRAL

REVERSE
OPERATION
SYSTEM (ROS)

FUEL

HIGH

LOW

ENGINE ON

BATTERY

CHOKE

ENGINE START

REVERSE

FAST

IGNITION SWITCH

PARKING BRAKE

FORWARD

SLOW

MOWER HEIGHT

MOWER LIFT

CLUTCH/BRAKE
PEDAL

CRUISE CONTROL
15

ATTACHMENT
CLUTCH DISENGAGED

ATTACHMENT
CLUTCH ENGAGED

DANGER, KEEP HANDS
AND FEET AWAY

15

SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.

FREE WHEEL
(Automatic Models only)

WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.

Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.

HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.

9

OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
ATTACHMENT
CLUTCH SWITCH

SERVICE
REMINDER/
HOURMETER

CHOKE
CONTROL

LIGHT
SWITCH

ROS "ON" POSITION

THROTTLE
CONTROL
IGNITION
SWITCH

BRAKE
PEDAL

FORWARD
DRIVE PEDAL
REVERSE DRIVE
PEDAL

PARKING
BRAKE
ATTACHMENT
LIFT LEVER

FREEWHEEL
CONTROL

FIG. 4
Our tractors conform to the safety standards of the American National Standards Institute.
BRAKE PEDAL - Used for braking the tractor and starting
the engine.
PARKING BRAKE - Locks clutch/brake pedal into the
brake position.
REVERSE DRIVE PEDAL- Used for reverse movement
of tractor.
REVERSE OPERATION SYSTEM (ROS) “ON” POSITION - Allows operation of mower deck or other powered
attachment while in reverse.
IGNITION SWITCH - Used for starting and stopping the
engine.
CHOKE CONTROL - Used when starting a cold engine.
THROTTLE CONTROL - Used to control engine speed.

SERVICE REMINDER / HOUR METER – Indicates when
service is required for the engine and mower.
ATTACHMENT CLUTCH SWITCH - Used to engage the
mower blades, or other attachments mounted to your
tractor.
ATTACHMENT LIFT LEVER - Used to raise, lower, and
adjust the mower deck or other attachments mounted to
your tractor.
FREEWHEEL CONTROL - Disengages transmission for
pushing or slowly towing the tractor with the engine off.
FORWARD DRIVE PEDAL - Used for forward movement
of tractor.
LIGHT SWITCH - Turns the headlights on and off.

10

OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide
vision safety mask over spectacles or standard safety glasses.
00155

HOW TO USE YOUR TRACTOR

CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty
grass catcher, etc.

TO SET PARKING BRAKE (See Fig. 5)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress brake pedal into full “BRAKE” position and
hold.
• Place parking brake lever in “ENGAGED” position
and release pressure from brake pedal. Pedal should
remain in “BRAKE” position. Make sure parking brake
will hold tractor secure.
PUSH IN TO "DISENGAGE"
IGNITION
KEY

TO USE THROTTLE CONTROL (See Fig. 5)
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
battery charging rate.
• Full throttle offers the best bagging and mower performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the
forward and reverse drive pedals.
• Start tractor and release parking brake.
• Slowly depress forward or reverse drive pedal to begin
movement. Ground speed increases the further down
the pedal is depressed.

ATTACHMENT
CLUTCH SWITCH
PULL OUT TO
"ENGAGE"

CHOKE
CONTROL

TO USE CHOKE CONTROL (See Fig. 5)

THROTTLE
CONTROL04000

"BRAKE"
POSITION

Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.

FORWARD DRIVE
PEDAL
REVERSE
DRIVE
PEDAL
PARKING BRAKE
BRAKE PEDAL "DRIVE"
POSITION

TO ADJUST GAUGE WHEELS (See Fig. 6)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
NOTE:Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in the Operation
section of this manual).
• With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off
the ground. Install gauge wheel in appropriate hole
with shoulder bolt, 3/8 washer, and 3/8-16 locknut and
tighten securely.
• Repeat for opposite side installing gauge wheel in same
adjustment hole.

FIG. 5

STOPPING (See Fig. 5)

MOWER BLADES • To stop mower blades,move attachment clutch switch
to “DISENGAGED” position.
GROUND DRIVE • To stop ground drive, depress brake pedal into full
“BRAKE” position.
I M P O R TA N T : F O R W A R D A N D R E V E R S E D R I V E
PEDALS RETURN TO NEUTRAL POSITION WHEN NOT
DEPRESSED.

ENGINE • Move throttle control between half and full speed (fast)
position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping may cause engine
to “backfire”.
• Turn ignition key to “STOP” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke to stop engine.

GAUGE WHEEL
MOUNTING
BRACKET

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY
TO BE DISCHARGED, (DEAD).

NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

3/8-16 LOCKNUT

01
42
3

3/8 WASHER

SHOULDER
BOLT

GAUGE WHEEL

11

FIG. 6

OPERATION
REVERSE OPERATION SYSTEM (ROS)
(See Fig. 8)

TO OPERATE MOWER (See Fig. 7)
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with the
engine running and the attachment clutch engaged will shut off
the engine. You must remain fully and centrally positioned in the
seat to prevent the engine from hesitating or cutting off when
operating your equipment on rough, rolling terrain or hills.
• Select desired height of cut.
• Start mower blades by engaging attachment clutch
control.
• TO STOP MOWER BLADES - disengage attachment
clutch control.

Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position.
WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.

CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.

USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders
will enter the mowing area.
• Depress brake pedal all the way down.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before and while backing.
• Slowly depress reverse drive pedal to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.

TO ADJUST MOWER CUTTING HEIGHT (See
Fig. 7)
The position of the attachment lift lever (A) determines the
cutting height.
• Put attachment lift lever in desired cutting height slot.
The cutting height range is approximately 1" to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.

ROS "ON" POSITION

02828

FIG. 8

ATTACHMENT
CLUTCH
SWITCH
PULL OUT TO
"ENGAGE"
04000

A

TO OPERATE ON HILLS
CAUTION: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.

PUSH IN TO
"DISENGAGE"

•

ATTACHMENT
LIFT LEVER
HIGH POSITION

LOW
POSITION

ENGINE "ON" POSITION
(NORMAL OPERATING)

•
•

FIG. 7

•
•
•

12

Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If stopping is absolutely necessary, push brake pedal
quickly to brake position and engage parking brake.
To restart movement, slowly release parking brake and
brake pedal.
Slowly depress appropriate drive pedal to slowest setting.
Make all turns slowly.

OPERATION
TO TRANSPORT (See Figs. 4 and 9)

IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.

When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling
position. Free wheel control is located at the rear drawbar
of tractor.
• Raise attachment lift to highest position with attachment
lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.
• Do not push or tow tractor at more than two (2)
MPH.
• To reengage transmission, reverse above procedure.

CAUTION: Alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract moisture
which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before
storage of 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next season.
See Storage Instructions for additional information.
Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 4)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
• Be sure freewheel control is in the transmission engaged
position.
• Sit on seat in operating position, depress brake pedal
and set parking brake.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to fast position
• Pull choke control out for a cold engine start attempt.
For a warm engine start attempt the choke control may
not be needed.
NOTE: Before starting, read the warm and cold starting
procedures below.
• Insert key into ignition and turn key clockwise to
“START” position and release key as soon as engine
starts. Do not run starter continuously for more than
fifteen seconds per minute. If the engine does not start
after several attempts, push choke control in, wait a
few minutes and try again. If engine still does not start,
pull the choke control out and retry.

02219

FIG. 9
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACHMENTS
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
• Check engine oil with tractor on level ground.
• Pull up and remove oil fill cap/dipstick; wipe oil off. Reinsert the dipstick into the tube and push down firmly
into place. Remove and read oil level. If necessary,
add oil until “FULL” mark on dipstick is reached. Do
not overfill.
• For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
• To change engine oil, see the Maintenance section in
this manual.

WARM WEATHER STARTING (50° F and above)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. If the engine starts
to run roughly, pull the choke control out slightly for a
few seconds and then continue to push the control in
slowly.
• The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.
COLD WEATHER STARTING (50° F and below)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. Continue to push
the choke control in small steps allowing the engine to
accept small changes in speed and load, until the choke
control is fully in. If the engine starts to run roughly, pull
the choke control out slightly for a few seconds and
then continue to push the control in slowly. This may
require an engine warm-up period from several seconds
to several minutes, depending on the temperature.

ADD GASOLINE
•

Fill fuel tank to bottom of filler neck. Do not overfill.
Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits and reduce
valve life). Do not mix oil with gasoline. Purchase fuel
in quantities that can be used within 30 days to assure
fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.

13

OPERATION
NOTE: During this procedure there will be no movement
of drive wheels. The air is being removed from hydraulic
drive system.
• Shut- off engine and set parking brake.
• Engage transmission by placing freewheel control in
engaged position (See “TO TRANSPORT” in this section of manual).
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed.
Disengage parking brake.
• Drive tractor forward for approximately five feet then
backwards for five feet. Repeat this driving procedure
three times.
Your transmission is now purged and now ready for normal
operation.

AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Release the parking brake and let the brake slowly
return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can be used during the engine warmup period after the transmission has been warmed
up and may require the choke control be pulled out
slightly.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.

MOWING TIPS
•
•

PURGE TRANSMISSION

•

CAUTION: Never engage or disengage
freewheel lever while the engine is
running.

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.

To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.

•
•
•
•

Place tractor safely on level surface with engine off
and parking brake set.
Disengage transmission by placing freewheel control
in freewheeling position (See “TO TRANSPORT” in
this section of manual).
Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position.
Disengage parking brake
Depress forward drive pedal to full forward position,
hold for five (5) seconds and release pedal. Depress
reverse drive pedal to full reverse position, hold for five
(5) seconds and release pedal. Repeat this procedure
three (3) times.

00272

FIG. 10
•

•

•
•

•

14

When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc. After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig. 10).
If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material. Regulate ground speed by
selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.

MAINTENANCE
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE

E
E
RS
S
AG
RS
RS
US
OU SON OR
H
UR
OU HOU
H
C
T
O
H
A
A
0
S
H
SE RE
25
10
50
EE Y 8
R
RY ERY ERY ERY FO
OR
E
E
F
BE
SERVICE
EV
EV
EV
EV
EV
BE

DATES

Check Brake Operation
Check Tire Pressure

T
R
A
C
T
0
R

Check Operator Presence and
ROS Systems
Check for Loose Fasteners

5

Sharpen/Replace Mower Blades

3

Lubrication Chart
Check Battery Level

4

Clean Battery and Terminals
Check Transaxle Cooling
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)
1,2

Clean Air Filter

2

Clean Air Screen

2

Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)

1, 2

Clean Engine Cooling Fins

maint_sch-tractore.ROS.e

E
N
G
I
N
E

1,2

Change Engine Oil (without oil filter)

2

Replace Spark Plug
Replace Air Filter Paper Cartridge

2

Replace Fuel Filter
1 - Change more often when operating under a heavy load or
in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.
Do not overtighten.

LUBRICATION CHART

GENERAL RECOMMENDATIONS

➀SPINDLE

The warranty on this tractor does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
tractor as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should
make any of the adjustments described in the Service
and Adjustments section of this manual.
• At least once a year you should replace the spark
plug, clean or replace air filter, and check blades and
belts for wear. A new spark plug and clean air filter
assure proper air-fuel mixture and help your engine
run better and last longer.

•

ZERK

➀FRONT WHEEL

➀FRONT WHEEL

BEARING ZERK

BEARING ZERK

➁ENGINE

BEFORE EACH USE
•
•
•
•

➀SPINDLE

ZERK

01964

Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.

➀GENERAL PURPOSE GREASE
➁REFER TO MAINTENANCE “ENGINE” SECTION
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF
THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE
LUBRICANT SPARINGLY.

15

MAINTENANCE
TRACTOR

BLADE CARE

Always observe safety rules when performing any maintenance.

For best results mower blades must be kept sharp. Replace
bent or damaged blades.

BRAKE OPERATION
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted. (See
“TO CHECK BRAKE” in the Service and Adjustments section of this manual).

CAUTION: Use only a replacement
blade approved by the manufacturer of
your tractor. Using a blade not approved
by the manufacturer of your tractor is
hazardous, could damage your tractor
and void your warranty.

TIRES
• Maintain proper air pressure in all tires (Refer to tire
specifications on the side of tires).
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.

BLADE REMOVAL (SEE FIG. 12A)
•
•
•

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.

•

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See FIG. 11)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.

•

TRAILING
EDGE UP

MANDREL
ASSEMBLY

BLADE
CENTER
HOLE

02
54
5

STAR

BLADE BOLT

FIG. 12A

CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
• When the engine is running with the ignition switch in
the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse
should NOT shut off the engine.

TO SHARPEN BLADE (See Fig. 12B)

ENGINE "ON" POSITION
(NORMAL OPERATING)

FIG. 11

Reassemble blade bolt, lock washer and flat washer
in exact order as shown.
Tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS
REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN
IN THE REPAIR PARTS.

CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never operate unless
the operator is in the seat.

ROS "ON" POSITION

Raise mower to highest position to allow access to
blades.
Remove blade bolt, lock washer and flat washer securing
blade.
Install new or resharpened blade with trailing edge up
towards deck as shown.

02828

16

NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual
damage to mower and engine.
• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the
mower.
• To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a
cone balancer, follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
• Slide blade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.

MAINTENANCE
ENGINE

CENTER HOLE

LUBRICATION
01

Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.

20

2

BLADE

5/8" BOLT
OR PIN

SAE VISCOSITY GRADES
10W30
5W-30

FIG. 12B

-20

F
C

BATTERY

-30

30
-10

32

40

0

60
10

100

80
20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

Your tractor has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
• Remove terminal guard.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.
• Coat terminals with grease or petroleum jelly.
• Reinstall battery (See “CONNECT BATTERY” in the
Assembly section of this manual).

oil_visc_chart4_e

Change the oil after every 25 hours of operation or at least
once a year if the tractor is not used for 25 hours in one
year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation.
TO CHANGE ENGINE OIL (See Fig. 13)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove yellow cap from end of drain valve and install
the drain tube onto the fitting.
• Unlock drain valve by pushing inward and turning
counterclockwise.
• To open, pull out on the drain valve.
• After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
• Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.

V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

OIL DRAIN VALVE

The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or
steam to clean transaxle.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean cooling fins.

CLOSED
AND
LOCKED
POSITION

46
02

YELLOW
CAP

3

DRAIN
TUBE

FIG. 13
•

TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
nearest authorized service center/department.

0
-20

17

Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.

MAINTENANCE
•

MUFFLER

Use gauge on oil fill cap/dipstick for checking level.
For accurate reading, insert dipstick into the tube
and push down firmly into place before removing.
Keep oil up to, but not over, the “FULL” line on dipstick. Push dipstick down firmly into the tube when
finished.

Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.

CLEAN AIR SCREEN
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.

IN-LINE FUEL FILTER (See Fig. 14)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.

CLEAN AIR INTAKE/COOLING AREAS
To insure proper cooling, make sure the grass screen,
cooling fins, and other external surfaces of the engine are
kept clean at all times.
Every 100 hours of operation (more often under extremely
dusty, dirty conditions), remove the blower housing and
other cooling shrouds. Clean the cooling fins and external
surfaces as necessary. Make sure the cooling shrouds are
reinstalled.
NOTE: Operating the engine with a blocked grass screen,
dirty or plugged cooling fins, and/or cooling shrouds removed
will cause engine damage due to overheating.

CLAMP
CLAMP

AIR FILTER

FUEL
FILTER

Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions.
See Engine Manual.

00667

FIG. 14

CLEANING

ENGINE OIL FILTER

•

Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.

Replace the engine oil filter every season or every other
oil change if the tractor is used more than 100 hours in
one year.

18

SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress brake pedal fully and set parking brake.
• Place attachment clutch in “DISENGAGED” position.

•
•
•

Turn ignition key to “STOP” and remove key.
Make sure the blades and all moving parts have completely stopped.
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with
plug.
IMPORTANT: IF AN ATTACHMENT OTHER THAN THE
MOWER IS TO BE MOUNTED ON THE TRACTOR,
REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS
(C) FROM TRACTOR AND HOOK THE CLUTCH SPRING
(Q) INTO THE CABLE GUIDE ON FRONT EDGE OF
LOWER DASH.

TO REMOVE MOWER (See Fig. 15)

•
•
•
•
•
•
•

Place attachment clutch in “DISENGAGED” position.
Lower attachment lift lever to its lowest position.
Roll belt off engine pulley (M) and belt keepers (G).
Remove retainer spring (K), slide collar (L) off and push
housing guide (P) out of bracket.
Remove clutch cable spring (Q) from idler arm (R).
Disconnect front link (E) from mower - remove retainer
spring and washer.
Go to either side of mower and disconnect mower
suspension arm (A) from chassis pin (B) and rear lift
link (C) from rear mower bracket (D) - remove retainer
springs and washers.

TO INSTALL MOWER (See Fig. 16-19)
Be sure tractor is on level surface and engage parking
brake.
• Lower attachment lift lever to it's lowest position.
CAUTION: LIFT LEVER IS SPRING
LOADED. HAVE A TIGHT GRIP ON
LIFT LEVER, LOWER IT SLOWLY AND
ENGAGE IN LOWEST POSITION.

CAUTION: AFTER REAR LIFT LINKS
ARE DISCONNECTED, THE ATTACHMENT LIFT LEVER WILL BE SPRING
LOADED. HAVE A TIGHT GRIP ON LIFT
LEVER WHEN CHANGING POSITION
OF THE LEVER.
•

NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor.
• Slide mower under tractor until it is centered under
tractor.

Slide mower out from under right side of tractor.

M
F

G
R

G

Q
A

E

B
P

C

K
L

D

19

SERVICE AND ADJUSTMENTS
A

E

B

J

F

H
•
•

FIG. 16
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO
CHASSIS - Position hole in arm over pin (B) on outside
of tractor chassis and secure with retainer spring.
Repeat on opposite side of tractor.

FIG. 18
•

ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole
in tractor front suspension bracket (F).•
Insertend
of link (E) into hole in front mower bracket and secure
with washer and retainer spring (J).
• Install belt on engine pulley (M), in belt keepers (G).
IMPORTANT: CHECK BELT FOR PROPER ROUTING
IN ALL MOWER PULLEY GROOVES.
• Raise attachment lift lever to highest position.
• If necessary, adjust gauge wheels before operating
mower as shown in the Operation section of this
manual.

C
D

FIG. 17
•

ATTACH REAR LIFT LINKS (C) - Lift rear corner of
mower and position slot in link assembly over pin (D)
on rear mower bracket and secure with washer and
retainer spring.

M
F

G
R

G

Q
A

E

B
P

C

K
L

D
FIG. 19A

20

SERVICE AND ADJUSTMENTS
TO LEVEL MOWER

•

If adjustment is necessary, see step in Visual Adjustment instructions above.
• Recheck measurements, adjust if necessary until both
sides are equal.
FRONT-TO-BACK ADJUSTMENT (See Figs. 19D and 19E)
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting results, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" lower than the
rear tip when the mower is in its highest position.

Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the
appearance of your lawn and lead you to think the mower
is not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 19B)
• With all tires properly inflated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
• With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower LH side of mower, or,
to the right to raise LH side of mower.

CAUTION: Blades are sharp. Protect your
hands with gloves and/or wrap blade with
heavy cloth.
•
•

A

Raise mower to highest position.
Position any blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear tip
of the blade.

02548

B

B

FIG. 19D
Turn nut left
to lower mower

Turn nut right
to raise mower

•
•

02948

FIG. 19B
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
• Test your adjustment by mowing some uncut grass
and visually checking the appearance. Readjust, if
necessary, until you are satisfied with the results.

•

If front tip of blade is not 1/8" to 1/2" lower than the rear
tip, go to the front of tractor.
With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (ltighten) to raise the front of
mower, or, counterclockwise (loosen) to lower the front
mower.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 19C)
• With all tires properly inflated, park tractor on level
ground or driveway.

B
A

CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
•
•

Raise mower to its highest position.
At both sides of mower, position blade at side and
measure the distance (A) from bottom edge of blade
to the ground. The distance should be the same on
both sides.

Tighten adjust nut
B to raise mower
02950

Loosen adjust
nut B to lower
mower

Loosen jam nut A first

FIG. 19E
NOTE: Each full turn of the adjustment nut will change
mower height about 1/8".
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 1/2" lower than the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.

02966

A

A
FIG. 19C

21

SERVICE AND ADJUSTMENTS
TO REPLACE MOTION DRIVE BELT(See FIG.
21)

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 20)

Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
BELT REMOVAL 1. Remove mower (See “TO REMOVE MOWER” in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
2. Disconnect clutch wire harness (A).
3. Remove anti-rotation link (B) on right side of tractor.
4. Remove belt from stationary idler (C) and clutching idler
(D).
5. Remove belt from centerspan idler (E).
6. Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades (F).
7. Remove belt downward from engine pulley and around
electric clutch (G).
8. Slide belt toward rear of tractor, off the steering plate
(H) and remove from tractor.
BELT INSTALLATION 1. Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).
2. Pull belt toward front of tractor and roll belt around
electric clutch and onto engine pulley (G).
3. Pull belt toward rear of tractor. Carefully work belt down
around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.
4. Install belt on centerspan idler (E).
5. Install belt through stationary idler (C) and clutching
idler (D).
6. Reinstall anti-rotation link (B) on right side of tractor.
Tighten securely.
7. Reconnect clutch harness (A).
8. Make sure belt is in all pulley grooves and inside all belt
guides and keepers.
9. Install mower (See “TO INSTALL MOWER” in this section of manual).

The mower blade drive belt may be replaced without tools.
Park the tractor on level surface. Engage parking brake.
BELT REMOVAL • Remove mower from tractor (See “TO REMOVE
MOWER” in this section of this manual).
• Work belt off both mandrel pulleys and idler pulleys.
• Pull belt away from mower.
BELT INSTALLATION • Install new belt in reverse order of removal.
• Make sure belt is in all pulley grooves and inside all
belt guides.
• Install mower in reverse order of removal instructions.
IDLER PULLEYS

MANDREL
PULLEYS

FIG. 20

TO CHECK BRAKE
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced.
You may also check brake by:
• Park tractor on a level, dry concrete or paved surface,
depress brake pedal all the way down and engage
parking brake.
• Disengage transmission by placing freewheel control
in “transmission disengaged” position. Pull freewheel
control out and into the slot and release so it is held in
the disengaged position.
The rear wheels must lock and skid when you try to manually
push the tractor forward. If the rear wheels rotate, then the
brake needs to be serviced. Contact a or other qualified
service center.

G

H
B

A
C
J
D
E

F

02953
electric

22

FIG. 21

SERVICE AND ADJUSTMENTS
TO START ENGINE WITH A WEAK BATTERY
(See Fig. 23)

TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor. See “PURGE TRANSMISSION”
in the Operation section of this manual.

WARNING: Lead-acid batteries generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.

TO ADJUST STEERING WHEEL
ALIGNMENT
If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly
section of this manual.

If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the Maintenance section
of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:

FRONT WHEEL TOE-IN/CAMBER

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO
START OTHER VEHICLES.

The front wheel toe-in and camber are not adjustable on
your tractor. If damage has occurred to affect the front
wheel toe-in or camber, contact your nearest authorized
service center/department.

TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal (C) of fully charged battery.
• Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.

TO REMOVE WHEEL FOR REPAIRS
(See Fig. 22)
•
•

Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not lose).
• Repair tire and reassemble.
• On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.

TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.

WASHERS

02614

WEAK OR DEAD
BATTERY

RETAINING
RING

FULLY CHARGED
BATTERY

FIG. 23

AXLE
COVER
SQUARE KEY
(REAR WHEEL ONLY)

3

0066

FIG. 22

23

SERVICE AND ADJUSTMENTS
ENGINE

TO REPLACE HEADLIGHT BULB
•
•
•
•

Raise hood.
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.

TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CHOKE CONTROL

INTERLOCKS AND RELAYS

The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the Repair
Parts section.

TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.

TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 24)
•
•
•
•

Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedure.

HOOD

HEADLIGHT
WIRE
CONNECTOR

02778

FIG. 24

24

STORAGE
ENGINE

Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.

FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.

WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

TRACTOR

•

Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.

Remove mower from tractor for winter storage. When mower
is to be stored for a period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a clean, dry area.
• Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Maintenance section of this
manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of
this manual).

BATTERY
•
•
•

•
•

CYLINDER(S)

Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.

•
•
•
•

Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).

OTHER
•
•
•
•

Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.

25

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

CORRECTION

Will not start

1.
2.
3.
4.
5.
6.
7.

Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.

1.
2.
3.
4.
5.
6.
7.

8.
9.

Loose or damaged wiring.
Carburetor out of adjustment.

8.
9.

10.

Engine valves out of adjustment.

10.

Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

1.
2.
3.
4.
5.
6.
7.

Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.

1.
2.
3.
4.
5.
6.
7.

8.

Engine valves out of adjustment.

8.

Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Engine will not turn over

1.
2.
3.
4.
5.
6.
7.
8.
9.

Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).

1.
2.
3.
4.
5.
6.
7.
8.
9.

Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.

Engine clicks but will not
start

1.
2.
3.
4.

Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.

1.
2.
3.
4.

Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.

Loss of power

1.
2.
3.
4.
5.
6.
7.
8.
9.

Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.

1.
2.
3.
4.
5.
6.
7.
8.
9.

Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.

Hard to start

Excessive vibration

10.
11.
12.
13.
14.

Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.

10.
11.
12.
13.
14.

15.

Engine valves out of adjustment.

15.

1.
2.
3.

Worn, bent or loose blade.
Bent blade mandrel.
Loose/damaged part(s).

1.
2.
3.

26

Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.

TROUBLESHOOTING POINTS
PROBLEM

CAUSE

CORRECTION

Engine continues to run
when operator leaves seat
with attachment clutch
engaged

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.

Poor cut - uneven

1.
2.
3.
4.
5.

Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.

Replace blade. Tighten blade bolt.
Level mower deck.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.

Mower blades will not
rotate

1.
2.
3.
4.

Obstruction in clutch mechanism.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.

1.
2.
3.
4.

Remove obstruction.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.

Poor grass discharge

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace/sharpen blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.

Headlight(s) not working
(if so equipped)

1.
2.
3.
4.
5.

Light switch is “OFF”.
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.

1.
2.
3.
4.
5.

Turn light switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.

Battery will not charge

1.
2.
3.
4.

Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.

1.
2.
3.
4.

Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.

Loss of drive

1.
2.
3.

Freewheel control in “disengaged” position.
Motion drive belt worn, damaged, or broken.
Air trapped in transmission during shipment
or servicing.

1.
2.
3.

Place freewheel control in “engaged” position.
Replace motion drive belt.
Purge transmission.

Engine “backfires” when
turning engine “OFF”

1.

Engine throttle control not set between half and
full speed (fast) position before stopping engine.

1.

Move throttle control between half and full speed
(fast) position before stopping engine.

27

SERVICE NOTES

28

SERVICE NOTES

29

SERVICE NOTES

30

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

FOL
DA
L
O
NG D
THIS
O
I
T
S
T
A
E
D LIN
1
5
DEG
E
RE
E
S
LOP
E

ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL

15 DEGREES MAX.

WARNING: To avoid serious injury, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.

31

532 41 73-88 11.02.07 AP

Printed in the U.S.A.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2007:11:02 10:10:22-04:00
Modify Date                     : 2007:11:12 10:22:05+01:00
Subject                         : HOEN2007_5324173-88
Producer                        : Acrobat Distiller 7.0 (Windows)
Mod Date                        : 2007:11:12 10:22:05+01:00
Creation Date                   : 2007:11:02 10:10:22-04:00
Author                          : Husqvarna
Creator Tool                    : Adobe InDesign CS2 (4.0.4)
Metadata Date                   : 2007:11:12 10:22:05+01:00
Document ID                     : uuid:7f8007dc-a886-49f1-81d4-30997354277e
Instance ID                     : uuid:e63782eb-6f57-4847-9719-8d0f64c4dc69
Format                          : application/pdf
Title                           : OM, LTH1742 Twin, 96041006700, 2007-11
Creator                         : Husqvarna
Description                     : HOEN2007_5324173-88
Page Count                      : 32
Page Mode                       : UseOutlines
Page Layout                     : SinglePage
EXIF Metadata provided by EXIF.tools

Navigation menu