Hyundai P224W Widescreen Lcd Monitor P224Wk Users Manual
P224WK to the manual 7a23b79d-9a6f-46df-8285-babf6b2c44a7
2015-01-23
: Hyundai Hyundai-P224W-Widescreen-Lcd-Monitor-P224Wk-Users-Manual-221844 hyundai-p224w-widescreen-lcd-monitor-p224wk-users-manual-221844 hyundai pdf
Open the PDF directly: View PDF 
.
Page Count: 44
| Download | |
| Open PDF In Browser | View PDF |
PANTONE COLOR 432 U PANTONE COLOR 432 U U.S.A. U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/Monitor technician for assistance. Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Connecting of peripherals requires the use of grounded shielded signal cables. DID_eng.indb 2 2009-09-15 오후 8:24:18 DECLARATION OF CONFORMITY For the following product : All of Digital sigange HYUNDAI IT provides Manufactured at : (factory name, address) 1. Hyundai IT Corp. 1229 In-ri, Apo-eup Gimcheon, Gyeongsangbuk-do 740-860 Rep. of Korea 2. Hyundai IT Corp. San 136-1 Ami-ri, Bubal-eub, Ichon-si, Kyungki-Do, 467-860 Rep. of Korea We herewith confirmed to comply with the requirements set put in the Council Directive on the Approximation of the Lows of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC), Low-Voltage Directive(73/23/EEC , 93/68/EEC) . For the evaluation regarding the Directives, the following standards were applied: EN60065 : 2002 EN55022 : 1998+A1 : 2000 +A2 : 2003 CLASS A EN55024 : 1998+A1 : 2001 +A2 : 2003 EN 61000-3-2 : 2000 +A2 : 2005 EN 61000-3-3 : 1995 +A1 : 2001 +A2 : 2005 DID_eng.indb 3 2009-09-15 오후 8:24:18 Contents Major features................................................................................................2 Safety Information.........................................................................................2 Be sure to understand...................................................................................5 Check the product list....................................................................................6 Proper location for product installation.......................................................7 Title and function of each part.....................................................................8 How to Connecting Kiosk............................................................................11 How to Connecting Digital RGB(HDMI)......................................................12 How to Connecting analog RGB (PC D-SUB)..............................................14 How to Connecting the component (Option)............................................16 How to Connecting the the video (Option)...............................................18 Adjusting OSD and explanation of its function........................................19 Diagnosis......................................................................................................33 Specifications...............................................................................................35 English DIGITAL SIGNAGE **REMOTE CONTROL / RS232C COMMAND SPEC 1/35 DID_eng.indb 4 2009-09-15 오후 8:24:19 DIGITAL SIGNAGE Major features This product has been designed to enable the user ease of use, and display information effectively and conveniently. • TFT LCD Module adopted D320ML(I/G) / D400ML / D420ML(I/G/P/T) / D460ML(I/G/P/T/H) / D468ML(I/G/P/T/H) / D460SL(I) : 1366 x 768 WXGA (HD) D405ML(I/G) / D407ML(I/G/P/T) / D425ML(I/G/P/T)/ D465ML(I/G) / D467ML(I/G/P/T) / D525ML(I/G) / D825ML(I/G) / D525SL(I) / D705ML(I/G) / D705SL(I) / D825SL(I) : 1920 x 1080 WUXGA (Full HD) • Vivid digital color display • OSD control function • Automatic Image control • Automatic temperature control • Analog/Digital RGB(HDMI) input and output • Y Pb Pr/AV input and output • Built in multi-vision function Safety Information This product is designed to ensure user's safety. Avoid the following items to prevent serious electric shot and other dangers. - Do not place wet objects on or around the product or the power cord. - Do not cover or insert anything over or into the ventilation openings. - D o not place in a location where damage can be caused by oil, smoke, high temperature, high humidity, dust etc. - The product is not suitable for use at visual display workplaces according to §2 of the German Ordinance for Work with Visual Display Units. /36 DID_eng.indb 2 2009-09-15 오후 8:24:19 - The main plug of the power supply cord shall remain readily operable. - An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection. - Make sure that the power cord and other cables are correctly plugged in. - Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire. - Do not touch the power cord with wet hands, it may cause electric shock. - Overloaded AC outlets and extension cables are as dangerous as the power cord being damaged, call service engineer for replacement as it may cause electric shock or fire. - Do not use multiple devices in a single power outlet, it may cause overheating or fire. - Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen itself. - W hen cleaning the LCD screen / Surface, do not use chemical cleaning products as this can seriously damage the special coatings on the screen. Only use water to dampen a soft cloth and lightly clear the screen. - Over time dust deposits can build up inside the product, this can cause the product to overheat thus causing premature malfunction or fire. Please do not attempt to clean the inside of the product yourself, please contact the local service agent. - Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl. - In the case of cleaning, be sure to remove the power cord and wipe with a soft dry fabric. - Keep batteries for the remote control out of children's sight. - Batteries should be inserted using the correct polarity (+,-). English DIGITAL SIGNAGE - Use only new batteries, do not mix old & new. - Place unit on a stable bracket or surface. - More than 2 people should work together when moving or installing. /36 DID_eng.indb 3 2009-09-15 오후 8:24:19 DIGITAL SIGNAGE - Do not hang on or jump to the product or mounting rack. - When the product is left unused for a long time, be sure to unplug the power cord. - In the case of damage or breakage do not attempt to self repair, please contact local service engineer. - For D460SL(I), D525SL(I), D705ML(I/G), D705SL(I), D825SL(I), install the product on the flat surface and secure the wheels not to move itself or fall down. - For D460SL(I), D525SL(I), D705ML(I/G), D705SL(I), D825SL(I), make sure to turn the power off before connecting cables. - This manual contains general instructions for the display products only so refer to the provided CD-ROM manual and the driver installation manual for the driver installation instructions for touch screen and/or touch screen itself. - The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. - Shall be connected to a MAINS socket outlet with a protective earthing connection. - The disconnect device shall remain readily operable. - The socket-outlet shall be installed near the equipment and shall be easily accessible. - Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. /36 DID_eng.indb 4 2009-09-15 오후 8:24:20 DIGITAL SIGNAGE Image quality of the product English Be sure to understand CAUSE Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when identical frames / images are displayed continuasly. If displayed for prolonged periods of time this can become permanent. PREVENTION When you display a freeze frame for a long time, lower the brightness and contrast (Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame. COUNTERMEASURES emporary afterimage can be alleviated by displaying white or moving frame about 10 T hours.(But, permanent afterimage cannot be disappeared according to the property of LCD) This method is used to remove temporary afterimage that may occur after displaying a still frame for a certain time. It can take several minutes or hours to remove afterimage according to the severity. In the case that your cannot avoid displaying identical still image continuously, you can prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness of still image and time of display are the cause of afterimage, you are recommended to lower the brightness in that case. ! Above problem shall not be covered by warranty. /36 DID_eng.indb 5 2009-09-15 오후 8:24:20 DIGITAL SIGNAGE Check the product list Please check the following components provided with the product after you open the box. Base Frame Type Kiosk Type (Portrait) ! Kiosk Type (Landscape) Remote control & batteries Power Cord User's manual D-SUB Cable HDMI to DVI Cable (Option) HDMI cable RS232C Cable (Option) please check the following components provided with the product after you open the box and contact the dealer if any missing. ** The contents may vary depending on models and sometimes the contents may be attached on the product. /36 DID_eng.indb 6 2009-09-15 오후 8:24:21 Proper location for product installation 1. Locate the product at least 30cm away from the electric appliance or heating product. 2. The product must be placed at least 10cm away from the wall and ground. 3. Keep the product out of direct ray of light and locate screen not to be reflected by the sunlight. 4. Make sure the mounting rack firmly tightened before installation. ! English DIGITAL SIGNAGE Please take extra care during installation, it is possible to cause damage if the unit is handled badly or knocked. uct. /36 DID_eng.indb 7 2009-09-15 오후 8:24:21 DIGITAL SIGNAGE Title and function of each part Control Panel 1 Remote control receiving sensor. 2 Power display LED red-stand by/ Green-working. 3 ~ 0 OSD button. 3 Power button ; to turn the power on or off. 4 Input selection button : to select other connected 5 6 7 8 9 0 device. 3 4 5 POWER SOURCE MENU 6 Menu button : to display menu or exit from the menu. select button. To move down in OSD menu. To move up in OSD menu. To move left and control the volume down in OSD menu. To move right and control the volume up OSD menu. 7 8 9 0 SELECT VOL 1 2 Base Frame Type (Front) /36 DID_eng.indb 8 Kiosk Type (Rear) ** The locations of OSD board and remote control receiving sensor may vary depending on models. 2009-09-15 오후 8:24:22 DIGITAL SIGNAGE 1 AC IN 2 7 PC D-SUB OUT AC POWER SWITCH 8 # COMPONENT OUT (Y Pb Pr) UPGRADE English Terminal panel $ CVBS IN 3 HDMI IN 9 PC AUDIO IN % CVBS OUT 4 HDMI OUT 0 RS-232C OUT ^ COMPONENT AUDIO IN (L R) 5 SPEAKER OUT ! RS-232C IN & COMPOSITE AUDIO IN (L R) 6 PC D-SUB IN @ 1 COMPONENT IN (Y Pb Pr) 2 5 3 4 6 7 8 0 @ $ ^ 9 ! # % & ** The locations of connectors may vary depending on models. - The items no. 12–17 are optional items. - When you select the "Source"button on the remote control, the "Source"menu of the "Option" item is displayed. DID_eng.indb 9 /36 2009-09-15 오후 8:24:23 DIGITAL SIGNAGE Remote control 1 2 3 4 6 7 5 9 8 1 To turn the power on or off. 2 Move up in OSD menu. 3 To move left or control the volume down in OSD menu. 4 To move right or control the volume up in OSD menu. 5 To move down in OSD menu. 6 Select in OSD menu. 7 Display the menu screen. 8 Close the menu screen. 9 Convert the input signal. How to insert batteries 1 Pull while pressing at rear lid. 2 Insert the batteries into proper polarities (+,-). 3 Use after the lid closed. 10/36 DID_eng.indb 10 2009-09-15 오후 8:24:23 DIGITAL SIGNAGE English How to Connecting Kiosk PC or Source (Satellite receiver, Camcorder etc.) 11/36 DID_eng.indb 11 2009-09-15 오후 8:24:24 DIGITAL SIGNAGE How to Connecting Digital RGB(HDMI) 1 2 1. Please ensure that the power to the device is switched off, then connect each cable one after another before restoring power. 1 when connect HDMI to HDMI cable 2 when connect DVI to HDMI cable – must utilize device with DVI signal output from peripheral device 2. Connect the power code to the product. 3. Turn on the power of the product and peripheral device. Screen shows up within 10 seconds. 4. Select "HDMI" input by pressing "SOURCE" on OSD button or remote control. – HDMI input gives better video quality than analog RGB input. – Both HDMI and analog RGB support plug and play. 12/36 DID_eng.indb 12 2009-09-15 오후 8:24:24 Support timing for HDMI nds. ! NO Resolution Horizontal frequency (KHz) Vertical frequency (Hz) 1 480p 640 x 480p 60 2 576p 720 x 576p 50 3 720p 1280 x 720p 50 / 60 4 1080i 1920 x 1080i 50 / 60 5 640 x 480 31.47 59.94 6 640 x 480 37.88 60.32 7 1024 x 768 48.36 60 8 1360 x 768 47.70 60 9 1360 x 768 64.00 60 10 1600 x 1200 75.00 60 11 1920 x 1080 67.50 60 12 1080p 1920 x 1080p 60 English DIGITAL SIGNAGE 9, 10, 11 and 12 are only for Full HD 13/36 DID_eng.indb 13 2009-09-15 오후 8:24:24 DIGITAL SIGNAGE How to Connecting analog RGB (PC D-SUB) 1. Please ensure that the power to the device is switched off, then connect each cable one after another before restoring power. 2. Connect D-SUB to D-Sub cable. Then tighten the screw of the cable after connecting PC D-SUB. 3. Connect the power cord to the product. 4. Turn on the power of the product and PC . The screen will appear within 10 seconds. 5. Select "PC" input by pressing "SOURCE" on OSD button or remote control. – HDMI input gives better video quality than analog RGB input. – Both HDMI and analog RGB support plug and play. 14/36 DID_eng.indb 14 2009-09-15 오후 8:24:25 Support timing for PC ! NO Resolution Horizontal frequency (KHz) Vertical frequency (Hz) 1 640 x 480 31.47 59.94 2 800 x 600 37.88 60.32 3 1024 x 768 48.36 60.00 4 1360 x 768 47.71 60.00 5 1280 x 1024 64.00 60.00 6 1600 x 1200 75.00 60.00 7 1920 x 1080 67.50 60.00 English DIGITAL SIGNAGE 5, 6 and 7 are only for Full HD 15/36 DID_eng.indb 15 2009-09-15 오후 8:24:25 DIGITAL SIGNAGE How to Connecting the component (Option) 1. Please ensure that the power to the device is switched off, then connect each cable one after another before restoring power. 2. Connect the component cables to Y, Pb, and Pr correctly. Connect BNC cable and tighten. 3. Connect the power cord to the product. 4. Turn on the power of the product and peripheral device . The screen will appear within 10 seconds. 5. Select "COMPONENT" input by pressing "SOURCE" on OSD button or remote control. 16/36 DID_eng.indb 16 2009-09-15 오후 8:24:25 Support timing for component & AV ! NO Resolution Horizontal frequency (KHz) Vertical frequency (Hz) 1 480i 720 x 480i 59.94 / 60 640 x 480p 59.94 / 60 2 480p 420 x 480p 59.94 / 60 3 576i 720 x 576i 50 4 576p 720 x 576p 50 5 720p 1280 x 720p 59.94 / 60 / 50 6 1080i 1920 x 1080i 59.94 / 60 / 50 7 1080p 1920 x 1080p 60 / 50 English DIGITAL SIGNAGE 7 is only for Full HD 17/36 DID_eng.indb 17 2009-09-15 오후 8:24:25 DIGITAL SIGNAGE How to Connecting the the video (Option) 1. Please ensure that the power to the device is switched off, then connect each cable one after another before restoring power. 2. Connect video cable and BNC cable, and then tighten. 3. Connect the power cord to the product. 4. Turn on the power of the product and peripheral device . The screen will appear within 10 seconds. 5. Select AV input by pressing "SOURCE" on OSD button or remote control. 18/36 DID_eng.indb 18 2009-09-15 오후 8:24:25 DIGITAL SIGNAGE Users can automatically adjust the picture mode according to the input mode. Picture Picture Picture Mode How to Select the Picture Mode U English Adjusting OSD and explanation of its function : Custom Picture Mode Custom Dynamic Custom High Colour Tone Standard Colour Tone Middle Size : Movie : Low NR : Mild Film Mode : Adjust Enter Menu : Size U PC NR : Adjust Enter Custom Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture mode" is highlighted. 3. Press ▶ or ↲ buttons to select "Picture mode". 4. The menu changes in the following order. AV/Component input : Custom -> Dynamic -> Standard -> Movie -> Mild PC/HDMI Input : Custom -> High -> Middle -> Low 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Custom : When the user wants to set the values directly. - Dynamic : Clear display - Standard : Most video contents are appropriate to this mode. - Movie : When watching a movie - Mild : Soft display. 19/36 DID_eng.indb 19 2009-09-15 오후 8:24:26 DIGITAL SIGNAGE How to Set the Desired Picture Users can manually adjust their desired picture Custom U Brightness : 40 Contrast : 80 Colour : 50 Tint : 50 Sharpness : 60 Move Adjust Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Custom" and press ▶or ↲ buttons to select "Custom". 4. Select required option by pressing the ▲ / ▼ or ↲ button, then Press◀ / ▶ button to adjust. 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Brightness : Adjust the brightness of the entire picture. - Contrast : Adjust the brightness and darkness of the object and backgrounds. - Colour : Adjust colors into deeper or lighter colors.(not operational in PC and HDMI mode) - Tint : Adjust colors naturally.(not operational in PC, HDMI and component mode) - S harpness : Adjust the clarity of object outlines.(not operational in PC and HDMI mode) 20/36 DID_eng.indb 20 2009-09-15 오후 8:24:26 How to Select a Colour Tone Users can adjust Color as users want. Colour Tone U Colour Tone : Custom Red : 50 Green : 50 Blue : 50 Move Enter 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Colour Tone" 4. Press ▶ or ↲ buttons to select "Colour Tone" . 5. Press ▲ / ▼ buttons, then the menu changes in the following order. Custom -> Cool2 -> Cool1 -> Normal -> Warm1 -> Warm2 English DIGITAL SIGNAGE Menu 6. Press EXIT button to escape OSD menu or press MENU button to return to the previous menu. - Custom : When the user wants to set the degree of RGB directly. - Cool : For cool colors with bluish tone. - Normal : For a general Colour Tone. - Warm : For warm colors with reddish tone. 21/36 DID_eng.indb 21 2009-09-15 오후 8:24:26 DIGITAL SIGNAGE How to Set the Display Size Users can adjust the display scale as they want Picture Picture Picture Mode U : Auto size Custom Wide Colour Tone Picture Mode : Custom Colour Tone 4:3 : Wide Panorama Size : Zoom NR : 4:3 PC Film Mode : 14 : 9 NR : Adjust Select Menu Size U Adjust Enter Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Size". 4. Press ◀ / ▶ or ↲ buttons and press ▲ / ▼ then the mode change in the following order. AV/Component Inputs : Auto Size ->Wide -> Panorama -> Zoom -> 4 : 3 -> 14 : 9 PC input : Wide -> 4 : 3 DVI input : 4 : 3 -> Wide -> 1 : 1 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Auto Size - Screen size adjust automatically by screen signal. - Wide - General broadcast picture is adjusted to 16:9. - Panorama - Picture enlarged to 16:9 format, letter box format. - Zoom - Zoom in 16:9 in vertical direction - 4 : 3 - 4 : 3 general picture size - 14 : 9 - 14 : 9 picture size - 1 : 1 - 1 : 1 real size 22/36 DID_eng.indb 22 2009-09-15 오후 8:24:26 How to set image adjustment in PC mode (Supported only in PC mode) Picture Auto Adjust U Phase : 52 H-Posilion : 16 V-Posilion : 24 Fiequency : -78 Move Enter Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to PC and press ▶ or ↲ buttons to select to "PC" 4. "Auto Adjust" is high lighted. 5. Press ↲ button to execute the "Auto Adjust" 6. Select the required option by pressing the ◀ / ▶ or ↲ button, then press ◀ / ▶button to adjust English DIGITAL SIGNAGE 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Auto Adjust : Horizontal/vertical positions are automatically adjusted. - Phase : To eliminate the shake of the picture. - H-Position : To adjust the horizontal position of the picture. - V-Position : To adjust the vertical position of the picture. - Frequency : To eliminate the shake of picture. 23/36 DID_eng.indb 23 2009-09-15 오후 8:24:26 DIGITAL SIGNAGE ow to Set Noise H Reduction(NR) User can eliminate noises on the screen in AV/Component/HDMI mode.(Not supported in PC mode) Picture Picture Mode U ow to Select the Audio H Mode : Custom Colour Tone Size : Off NR : On Film Mode : Adjust Enter 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "NR" . 4. Press ◀ / ▶ buttons to select to "NR". 5. Press ▲ / ▼ or ↲ buttons to set "On/Off". 6. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Menu Users can adjust sound mode automatically as they want. Sound Mode : Custom Volume : Standard Balance : Music Movie Auto Volume : Speech Sound Mode : Equalizer U Adjust Enter 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ buttons to move to "Sound" Icon. 3. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 4. Press ▶ or ↲ buttons, to select to Sound mode. then the menu changes in the following order. Custom->Standard -> Music -> Movie -> Speech 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Menu - Custom : When the user wants to set the values directly. - Standard : For the general sound. Most audio contents are appropriate to this mode. - Music : For enjoying original sound. - Movie : Grandiose sound. - Speech : Clear sound. 24/36 DID_eng.indb 24 2009-09-15 오후 8:24:27 DIGITAL SIGNAGE Users can adjust sound mode automatically as they want. Sound Sound Mode : Volume : 34 Balance : L50 R50 Equalizer U English How to Adjust the Desired Audio Mode Custom Auto Volume : Off Sound Mode : Stereo Move Enter Menu U 10KHz 50 3KHz 50 1KHz 50 300Hz 50 100Hz 50 Move L Adjust Menu 1. P ress Menu button. Menu items appear on the screen. 2. P ress ▲ / ▼ buttons to move to "Sound" Icon. 3. P ress ↲ button to select "Sound" Icon. "Mode" is highlighted. 4. Press ▲ / ▼ buttons to move to "Balance" or "Equalizer" . 5. P ress ↲ buttons to select "Balance" or "Equalizer". Balance or Equalizer menu appears. 6. S elect required option by pressing the ▲ / ▼ buttons, then Press ◀ / ▶ buttons to adjust. 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. -B alance : Adjusts the balance of left and right speakers. -E qualizer : Adjusts the audio output signal in the desired band. 25/36 DID_eng.indb 25 2009-09-15 오후 8:24:27 DIGITAL SIGNAGE How to Select Auto Volume This function will automatically give a similar volume size to each channel. Sound Mode : Volume : Balance : On Auto Volume : Off Sound Mode : Equalizer U How to Select Sound Mode Adjust Enter Menu 1. P ress Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ buttons to move to "Sound" Icon. 3. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 4. Press ▲ / ▼ buttons to move to "Auto Volume". 5. Press ◀ / ▶ or ↲ buttons to select "On/Off". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu Depending on the particular program being broadcast, you can select stereo or mono. Sound Mode : Volume : Balance : Stereo Auto Volume : Mono L Sound Mode : Mono R Equalizer U Select Enter Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Sound Mode". 4. Press ▶ or ↲ buttons to select to "Sound Mode". 5. Press ▲ / ▼ buttons to select to "Stereo"," Mono L"or "Mono R. 6. Press exit button to escape OSD MENU or press MENU button to return to the previous menu - Choose "Stereo" for channels that are broadcasting in Stereo. - Choose "Mono" for channels that are broadcasting in Mono, or if you are having difficultly receiving a Stereo signal. 26/36 DID_eng.indb 26 2009-09-15 오후 8:24:28 DIGITAL SIGNAGE Setup Reset Time Language : OSD Tone : Key Lock : Enter Select 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▶ or ↲ buttons to select to "Reset". 4. Press ↲ buttons to choose to "Reset". 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. English How to Reset Menu When you select "Reset" user setting Value will initialize. ow to Set Clock,Sleep Time, H ON/OFF Time Time U Clock : On Timer : 0:0 Off Timer : 0:0 On Time Volume : 0 Source : AV Move Enter 0:0 Off Off 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ buttons to move to "Time". 4. Press ▶ or ↲ buttons to select "Time". Time menu appears, then "Clock" is highlighted. 5. Press ◀ / ▶ buttons to move between Hour, Minute and Press ▲ / ▼ buttons to set Hour, Minute. Menu When the power supply(AC main power) is cut off, the clock is reset to the value before the Timer set. 27/36 DID_eng.indb 27 2009-09-15 오후 8:24:28 DIGITAL SIGNAGE Setup U Reset Time Language : English OSD Tone : Off Key Lock : Off Move Select6. Press ▲ / ▼ buttons to move to "On or Off Timer". 7. Press ▶ or ↲ buttons to select "On or Off Timer" . 8. Press ◀ / ▶ buttons to move between Hour, Minute and on/ off and Press ▲ / ▼ buttons to set Hour, Minute and on/off 9. Press ▲ / ▼ buttons to move to "On Time Volume". 10. Press ◀ / ▶ buttons to adjust Volume. Menu 11. Press ▲ / ▼ buttons to move to "Source" 12. Press ▶ or ↲ buttons to select to "Source" 13. Press ▲ / ▼ buttons to set to Source Choosing the Your Languages Setup Reset English Time Fiangais Language : Deutschland OSD Tone : Ilaliano Key Lock : Espafiol Nederland Suomi Polski Cestina Pyeeknn U Adjust Enter 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ button to move to "Language" and press ▶ or ↲ button to select to Language. 4. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Menu 28/36 DID_eng.indb 28 2009-09-15 오후 8:24:28 How to set OSD tone Setup U How to Set Key-Lock Reset Time Language : Off OSD Tone : On Key Lock : Adjust Enter 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ buttons to move to "OSD Tone" 4. Press ▶ or ↲ buttons to select to "OSD Tone". 5. Press ▲ / ▼ or ↲ buttons to set to "On/Off". English DIGITAL SIGNAGE Menu User can lock the control buttons on the front bottom of the Monitor. Setup U Reset Time Language : OSD Tone : Off Key Lock : On Select Enter Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to "Setup" Icon. 3. Press ↲ button to select "Setup" Icon. "Reset" is highlighted 4. Press ▲ / ▼ buttons to move to "Key Lock". 5. Press ▶ or ↲ buttons to select to "Key Lock". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. 29/36 DID_eng.indb 29 2009-09-15 오후 8:24:29 DIGITAL SIGNAGE ow to Set the Multi H Function Multi Multi H Set CounL : 0 Multi Function V Set CounL : 0 Heal Control Display Sequence : 0 H Edge ADJ : 0 V Edge ADJ : 0 SET ID : 0 Master U Move Off Adjust Menu U Move Enter Menu 1. P ress Menu button.Menu items appear on the screen. 2. Press ▲ / ▼ button to move to "Multi" Icon. 3. P ress ↲ button to select "Mutli" Icon. "Mutli Function" is highlighted 4. Press ▲ / ▼ buttons to set up and change the location of the screen to be displyed. H Set Count/ V Set Count/Display Sequence / H Edge ADJ / V Edge ADJ / SET ID/ Master (Example of installation) install 3x2 with 6 units Product 1 Product 2 Product 3 Product 4 Product 5 Product 6 30/36 DID_eng.indb 30 2009-09-15 오후 8:24:29 DIGITAL SIGNAGE installation item Product 1 Product 2 Product 3 Product 4 Product 5 Product 6 H Set Count 3 3 3 3 3 3 V Set Count 2 2 2 2 2 2 Display Sequence 1 2 3 4 5 6 H Edge ADJ / V Edge ADJ These are the set up value to make up the un-displayed area of Bezel Part. It can be adjustable according to the contents SET ID It is necessary to control via RS232 communication port on PC. But do not need to set up or change when they are not controlled by PC Master You are recommended to use the Master on state only one of products that you are using English Set up Value [Cautions] - In case of connecting the products in series from the input device (HDMI, analog RGB, component, video etc.), up to about 25 units are possible. But, the number of connecting devices can be different from the input signal level of each device and thereby amplified distributor can be needed for this product. (when over 25 units are connected, the screen may not be displayed properly) - You are recommended to use the component and progressive frequency of digital RGB in case of using multi-vision function. (It may not be displayed properly when using Video input and interlace frequency) 31/36 DID_eng.indb 31 2009-09-15 오후 8:24:29 DIGITAL SIGNAGE ow to Set the Heat H Control "Heat control" allows you set up fan operation according to interior temperture of the product Multi Multi U Multi Function Fan Control : Off Heal Control Fan Active Temp : 50 °C Hysteresis : 50 °C Temprature : 50 °C Move Enter Menu U Move Enter Menu 1. P ress Menu button. Menu items appear on the screen. 2. P ress ▲ / ▼ button to move to "Multi" Icon. 3. P ress ↲ button to select "Multi" Icon. "Multi Function" is highlighted 4. Press ▲ / ▼ buttons to move to "Heat Control". 5. P ress ▶ or ↲ buttons to set up and change the Heat Control. “Fan Control" - AS the fan operation options, following 3 options are available - Off : Fan is idle in Off status. - On : Fan is working in On-status. - Auto : Fan start working when the working temperature is higher than the measured temperature. • Fan active Temp -set up value to start the fan. • Hysteresis- tolerance value of fan operation temperature. • Temperature- measured current temperature by sensor affixed to PCB'A 32/36 DID_eng.indb 32 2009-09-15 오후 8:24:29 DIGITAL SIGNAGE When the product is not working properly, please check before you call customer center. English Diagnosis Symptoms How to solve the problem Screen displays late after the power is on. It happens not to show the screen noise when the power is on. Therefore it is not a defect. But if the screen doesn't show up within 5 minutes from turning on, please contact the customer center. The screen is too dark or bright? Adjust the brightness or contrast. The screen doesn't show up indicating "Out of range". You are using a signal which is outside the operating frequencies of the product (Unsupported), please change you video signal. when the screen is scrambled. please check the cable connection and the signal generator and contact customer center. Automatic switching-on function is not working / the input data were disapperared when reboot the system after setting up the time Automatic switching-on function is working when the product has been turned off via remote control or power button on main body. It is because that the setup values are deleted when the power cord is unplugged. The screen and sound are not synchronized Check if the power is on, suspended or is correctly plugged into the outlet. Plug the power cord of other peripheral device to the outlet that the product is being connected. 33/36 DID_eng.indb 33 2009-09-15 오후 8:24:29 DIGITAL SIGNAGE Symptoms How to solve the problem The screen displays without the sound. check the volume up and down with remote control and audio connection cable No sound from either right speaker or left speaker. Confirm the status of the sound balance on OSD menu and check the connection of speaker cable. Remote control doesn't work. Check if any foreign substances in the sensor and the polarity of battery inserted. If the batteries are drained, replace them with new batteries. PC D-SUB doesn't work. Set up the resolution referring to frequency table of input terminal. And re-boot the system as it supports Plug and Play. Fan on the rear doesn't work Check the status of temperature control on OSD menu The screen doesn't show up when display the multi-vision. check if it is set up to video input. Confirm if Interlace Timing was inputted. ( Refer to the cautions on Page 31 ) • If any problem unsolved by above diagnosis, please call customer center. 34/36 DID_eng.indb 34 2009-09-15 오후 8:24:30 DIGITAL SIGNAGE D320ML(I/G)/D400ML/ D420ML(I/G/P/T)/ D460ML(I/G/P/T/H)/ D468ML(I/G/P/T/H)/D460SL(I) Model LCD Screen size (HxV/mm) Recommended resolution Input D320ML(I/G) / D400ML / D420ML(I/G/P/T) / D460ML(I/G/P/T/H) / D468ML(I/G/P/T/H) / D460SL(I) English Specifications 1366 x 768 Pixel (HD) D320ML(I/G) : 697.7 x 392.3 / Pixel pitch 0.51 D400ML : 885.2 x 497.7 / Pixel pitch 0.65 D420ML(I/G/P/T) : 930.3 x 523.0 / Pixel pitch 0.68 D460ML(I/G/P/T/H), D468ML(I/G/P/T/H) : 1018.4x572.5 / Pixel 0.75 D460SL(I) : 1018.4x572.5 / Pixel 0.75 1360 x 768 @60Hz Digital RGB, Analog RGB, Component(Option), Video(Option), PC Audio L/R, Component Audio L/R(Option), Video Audio L/R(Option), RS232C Output Digital RGB, Analog RGB, Component(Option), Video(Option), Audio L/R, RS232C Power AC 100- 240V 50/60Hz Consumption (Typical) Control type D320ML(I/G) :170W / D400ML :200W / D420ML(I/G/P/T) :220W / D460ML(I/G/P/T/H), D468ML(I/G/P/T/H) :260W / D460SL(I) :260W Remote control, key control • Above specification may be changed without prior notification for quality improvement. 35/36 DID_eng.indb 35 2009-09-15 오후 8:24:30 DIGITAL SIGNAGE Specifications D405ML(I/G)/D407ML(I/G/P/T)/ D425ML(I/G/P/T)/D465ML(I/G)/ D467ML(I/G/P/T)/ D525ML(I/G)/ D825ML(I/G)/ D525SL(I)/ D705ML(I/G)/D705SL(I)/ D825SL(I) Model LCD Screen size (HxV/mm) Recommended resolution Input D405ML(I/G) : 885.6 x 498.15 / Pixel pitch 0.46 D407ML(I/G/P/T) : 885.2 x 497.7 / Pixel pitch 0.46 D425ML(I/G/P/T) : 930.25 x 523 / Pixel pitch 0.4845 x 0.4845 D465ML(I/G) : 1018.08 x 572.67 / Pixel pitch 0.53 D467ML(I/G/P/T) : 1018.4 x 572.5 / Pixel pitch 0.53 D525ML(I/G) : 1152.00 x 684.00 / Pixel pitch 0.60 D825ML(I/G) : 1806 x 1015 / Pixel pitch D525SL(I) : 1152.00 x 684.00 / Pixel pitch 0.60 D705ML(I/G), D705SL(I) : 1549.44 x 871.56 / Pixel pitch 0.81 D825SL(I) : 1806 x 1015 / Pixel pitch 1920 x 1080 @ 60Hz Digital RGB, Analog RGB, Component(Option), Video(Option), PC Audio L/R, Component Audio L/R(Option), Video Audio L/R(Option), RS232C Digital RGB, Analog RGB, Component(Option), Video(Option), Audio L/R, RS232C Power AC 100- 240V 50/60Hz Control type DID_eng.indb 36 1920 x 1080 Pixel (Full HD) Output Consumption (Typical) 36/36 D405ML(I/G)/D407ML(I/G/P/T)/D425ML(I/G/P/T)/D465ML(I/G)/ D467ML(I/G/P/T)/D525ML(I/G)/D825ML(I/G)/ D525SL(I)/D705ML(I/G)/ D705SL(I)/D825SL(I) D405ML(I/G) : 200W / D407ML(I/G/P/T), D425ML(I/G/P/T) : 260W / D465ML(I/G), D467ML(I/G/P/T) : 250W / D525ML(I/G), D825ML(I/G) : 320W / D705ML(I/G), D705SL(I) : 800W / D825SL(I) : 900W Remote control, key control • Above specification may be changed without prior notification for quality improvement. 2009-09-15 오후 8:24:30 < REMOTE CONTROL / RS232C COMMAND SPEC > 1. SPEED : 9600 Baud/s, 8 bit, No parity, 1 Stop bit. 2. REMOTE CONTROL WAVE FORM 1) Remote Control System Infrared rey system fosc=455KHZ fc=fosc/2=37.917KHZ 2) Signal code 2-1) Transmission - One pulse LEAD CODE CUSTOM CODE CUSTOM CODE DATA CODE DATA CODE LEAD CODE CUSTOM CODE HIGH CUSTOM CODE DATA CODE DATA CODE LOW LEAD CODE CUSTOM DATA CODE DATA CODE LOWCODE CUSTOM HIGHCODE LOW HIGH 9ms 4.5ms 9ms 4.5ms 9ms 4.5ms - Bit Desciption Bit “0” Bit “1” 0.56ms 0.56ms 0.56ms 2.25ms 2.25ms 2.25ms 0.56ms 0.56ms 0.56ms 1.125ms 1.125ms 1.125ms - Flame Interval Tf Tf Tf Tf Tf Tf Tf=108ms 455KHz Tf=108ms 455KHz Tf=108ms 455KHz DID_eng.indb 37 2009-09-15 오후 8:25:47 3. REMOTE CONTROL KEY CODE TABLE DATA LAYOUT Custom Code : 7788H KEY DATA POWER 0x80 MENU 0x95 EXIT 0x96 SOURCE 0xAC ENTER 0x8C UP 0x8D DOWN 0x8E LEFT 0x8F RIGHT 0x90 8O 8D 8F 8C 9O 8E 95 96 AC 4. COMMAND FORMAT * SET ID must select from the OSD menu and can't be select through the COMMAND. * Only one unit can be set as Master unit, select Master ON from the OSD Menu. (DEFAULT OFF) * For viewing COMMAND from Hyper Terminal windows, One unit must set as MASTER ON HEADER SET ID COMMAND TYPE did: x- or all- Command END DID_eng.indb 38 did:1-pf. To power off set that is SET ID 1 did:all-fr. To factory reset all set did:2-fn. To fan on set that is SET ID 2 2009-09-15 오후 8:25:47 5. COMMAND TYPE Command pn / pf Power on / Power off fn / ff Fan on / Fan off fr sd / sp / sc / sa Factory reset Source change ( d:HDMI, p:PC, c:Component, a:AV ) sbu / sbd Sub-Brightness 1 step up / down rou / rod Red Offset 1 step up / down gou / god Green Offset 1 step up / down bou / bod Blue Offset 1 step up / down scu / scd Sub-Contrast 1 step up / down rgu / rgd Red Gain 1 step up / down ggu / ggd Green Gain 1 step up / down bgu / bgd Blue Gain 1 step up / down blu / bld BACKLIGHT Value 1 step up / down chxvy H Set Count is x, V Set Count is y nhxvy H Set window is x, V Set window is y ehxvy H Edge ADJ is x, V Edge ADJ is y x ( figure ) Display sequence no is x cr Enable Color Control Mode; Under Cr mode, user can set color value without Header command ex) ro120 : Red Offset 120, bg100 : Blue Gain 100 ir Enable Ir Mode, In IR Mode, user can use keyboard buttonsas remote controller ps is DID_eng.indb 39 Description Current power status check. If current power is on(off), Hyper Terminal windows display “Power On(Power Off)” message. Current input source status check. If current input source is VGA, Hyper Terminal windows display “VGA Mode” message. 2009-09-15 오후 8:25:48 6. REMOTE CONTROL KEY CODE TABLE Key value Key value q quit ( from Ir mode ) t volume up p power v volume down u up r mute n down c picturemode j left l sleep k right d sound e enter s s.mode m menu y info->display x exit The others quit ( from Ir mode ) i input 7. REMOTE CONTROL KEY CODE TABLE Command Description did:all-wn=si. Change all units 'Display sequence' to 'SET ID' did:allfst-hxvy Set all units to 'H SET Count' = x, 'V SET Count' = y, 'Display sequence' = 'Select to SET ID' 8. CONNECTION &21752/(5 3& 0/6HULHV0RGHO 1 6 7 8 9 1 6 2 3 4 5 7 Rx Tx G 9Pin DIN male DID_eng.indb 40 2 2 3 3 5 5 Tx Rx G 8 9 2 3 4 5 9Pin DIN male 2009-09-15 오후 8:25:48 HYUNDAI IT Service Center @ DID_eng.indb 41 2009-09-15 오후 8:25:49
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2011:03:23 13:03:30+01:00 Create Date : 2009:10:20 11:18:42+09:00 Metadata Date : 2011:03:23 13:03:30+01:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Format : application/pdf Document ID : uuid:7c4cbac4-f1f8-d54f-934e-ec05ffa1374d Instance ID : uuid:363ed669-b787-45ee-a16a-e26dca3d6cdc Producer : Adobe PDF Library 7.0 Has XFA : No Page Count : 44 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools