IAdea IAD16004 Digital Signage Media Appliance User Manual

IAdea Corporation Digital Signage Media Appliance Users Manual

Users Manual

MBR-1100Hardware User Manual
iContents1. Introduction 11.1. Package contents 11.2. Installation 11.3. Physical view 32. Technical Data 42.1. Specifications 4
11. IntroductionThis document describes the hardware of the MBR-1100.1.1. Package contentsNOT INCLUDED: A USB mouse is required for system setup1.2. InstallationAttach wireless antennaAttach the wireless antenna as shown below, and then screw antenna clockwise onto the post.Mounting Option 1: [VESA Mount] The media bar can be attached to mounting posts on the back of screensby the supplied VESA MIS-D100 (100mmx100mm) compatible mounting plate(screw thread on the plate: M4)Attach media bar to the VESA mount plate1. Put the VESA mount plate on the bottom of the player, with the screw holes aligned.2. Make sure the countersunk holes are facing up, so when the screw goes in, the screw head is levelwith the surface.Media Bar Unit HDMI Extension CordWirelessAntennaAC Adapter(with select power plug)VESA Mount Plateand screwsVelcro
2Mounting Option 2: [Attach to HDMI port] Simply plug the player into the HDMI port of the monitor asshown below.Mounting Option 3: [Attach the player on the back of the monitor using Velcro]1. Separate the Velcro pads and stick one of them to the bottom of player.2. Stick the other Velcro pad onto the back of monitor, and then attach the player to it. Use HDMI extensioncord to connect player and the monitor.
31.3. Physical view
4Physical features (left to right in above illustration)•HDMI connector for digital video and audio combined output•Micro SD card slot•Micro USB for power adapter and ADB , Android debug console port•Reset button to perform factory reset•USB ports for USB content update and configuration•Power(green) and Status(orange) LED indicator•Ethernet port for network content update•Wireless antenna post2. Technical Data2.1. SpecificationsMBR-1100Video format support H.264 (up to 1080p,10Mbps)VC-1 (up to 1080p,10Mbps)MPEG-4 ASP (up to 1080p,10Mbps)MPEG-2 (up to 1080p,10Mbps)POPAI Screen Media Standards : S6 to S12, E4,E7,E8Image format support JPEG,PNG up to 1920x1080POPAI Screen Media Standards : S1 to S3, E1 to E3Audio codec supportMP3 up to 320KbpsPOPAI Screen Media Standards : S4, S5Dynamic content W3C HTML5 (HTML, CSS, JavaScript)W3C SMIL 3.0 instructions (sub-set)Physical I/O connectorsHDMIUSB 2.0 x 2RJ45 Ethernet portWireless antenna portMicro USB for DC in/ADBMicro SD card slotLED: Power(green)/Status(orange)Local storage8GBon-board flashmemoryor 8GB eMMC memory (only on Rev1.1)(up to 6 hrs of typical 720p video @ 3 Mbps)Micro SD card expansion slotAccessoriesACadapter(UL/FCC/CE/CCC/C-Tickcertified power supplies)HDMI extension cordWireless antennaVESA mount plate (screw thread : M4 )VelcroPower requirement5V 2A DCPower consumptionAverage 6 WEnvironmental Operating temperature: 0 – 40° C / 32 – 104° FHumidity: 10 – 85% @ 40° C / 32 – 104° F non-condensingDimensions107x68 x25.3mm (4.21x2.68 x1inches)Weight108.1g0.24lbsCertificationsCE/FCC/ICWarranty One-year limited parts & labor
5Federal Communications Commission (FCC) Statement15.21You are cautioned that changes or modifications not expressly approved by the part responsible forcompliance could void the user’s authority to operate the equipment.15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for helpFCC RF Radiation Exposure Statement:1. This Transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with a minimum distance of 20 cm between theradiator and your body.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subjectto the following two conditions: (1) this device may not cause interference, and (2) this devicemust accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radioexempts de licence.L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si lebrouillage est susceptible d'en compromettre le fonctionnement.RF Radiation Exposure Statement:
6This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & yourbody. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour unenvironnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm dedistance entre la source de rayonnement et votre corps.

Navigation menu