IAdea XMP-6200 Digital Signage Media Appliance User Manual
IAdea Corporation Digital Signage Media Appliance
IAdea >
User manual
XMP P‐6200 Hard dware User Manu ual Contents Introduction 1.1. Package contents 1.2. Installation 1.3. Physical view 1. 2. Technical Data 2.1. Specifications 1. Intro oduction This do ocument desccribes the hardware of the XMP‐6200. 1.1. Package ccontents Media Player Unit AC Adapter (with h select power plug) Wi‐Fi Anteenna HDMI Cable Vellcro (2 sets) NCLUDED: A U USB mouse is required for system setup NOT IN 1.2. Installatio on Attach h wireless antenna Attach h the wirelesss antenna as shown below w, and then sccrew antennaa clockwise onto the post. nting Option 1: [VESA Mo ount] The player can be atttached to mou unting posts o on the back off screens with Moun the built in VESA MIS‐D100 (10 00mmx100mm m) compatiblee mounting flaange(screw threead : M4) nting Option 2: [Attach th he player on n the back off the monitorr using Velcrro] Moun 1. Separate the Velcro pads, and a stick on th he bottom of player as show wn below. 2. SStick the other Velcro pad onto the backk of monitor, and a then attacch the player tto it. Use HDM MI cable to connect playeer and the monitor. 1.3. Physical view Physical features (left to right in above illustration) Reset button to perform factory reset USB ports for USB content update and configuration Power(green) and Status(orange) LED indicator HDMI 1.4 connector for digital video and audio combined output Ethernet port for network content update Wireless antenna post VESA mount Kensington lock Micro SD card slot HDMI port DC input port Micro USB for ADB , Android debug console port 2. Technical Data 2.1. Specifications XMP‐6200 Video format support POPAI Screen Media Standards S6 (MPEG‐1 SIF, 3Mbps CBR) S7 (MPEG‐1 480p, 10Mbps CBR) S8 (MPEG‐1 720p, 15Mbps CBR) S9 (MPEG‐2 480p, 6Mbps CBR) S10 (MPEG‐2 720p, 12Mbps CBR) S11 (MPEG‐4 AVC, 480p, 6Mbps CBR) S12 (MPEG‐4 AVC, 720p, 10Mbps CBR) E4 (VC‐1/WMV9, MP@ML, 720p) E7 (MPEG‐4 ASP, 480p, 10Mbps CBR) E8 (MPEG‐4 AVC, 1080p, 10Mbps CBR) Image format support POPAI Screen Media Standards S1 (JPEG 480p baseline) S2 (JPEG 720p baseline) S3 (JPEG 1080p baseline) E1 (PNG 24bpp+alpha, 480p) E2 (PNG 24bpp+alpha, 720p) E3 (PNG 24bpp+alpha, 1080p) Audio codec support POPAI Screen Media Standards S4 (MPEG L2 audio) S5 (MP3 audio, 320Kbps) Dynamic content W3C HTML5 (HTML, CSS, JavaScript) W3C SMIL 3.0 instructions (sub‐set) Physical I/O connectors HDMI 1.4 USB 2.0 x 2 RJ45 ethernet port Wi‐Fi antenna port Micro USB for ADB Micro SD card slot LED:: Power(green n)/Status(oran nge) Local storage 8 GB B on‐board flaash memory (u up to 6 hrs of typical 720p vvideo @ 3 Mb bps) Micrro SD card exp pansion slot Accessories AC adapter HDM MI cable Wi‐FFi antenna Velccro ( 2 sets ) Power requiremen nt 12V 1.5A DC Power consumptio on 6W Enviro onmental Operating temperrature: 0 – 38° C / 32 – 100 0.4° F Hum midity: 10 – 85 5% @ 40° C / 3 32 – 104° F no on‐condensingg Dimen nsions 167xx118.8x24.5 mm m ( 6.57x4.6 67x0.96 inchess) Weigh ht 275 g 1 lbs 0.61 Safetyy UL/FFCC/CE/CCC/C C‐Tick/VCCI ceertified powerr supplies Certifications CE/FFCC/VCCI/TELEC/CCC/IC Warraanty One‐year limited parts & labor 3. XMP P‐6200 Quickk Start Guide This prrinted quick gguide providess a quick walkthrough of the set up proceess. For comp plete documen ntation, please visit www.digisignag ge.com 3.1. B Conte Box ents Mediaa Player Unit AC Adaapter (with select p power plug) USB mouse requ uired 3.2. Wi‐Fi Antenna HDMI Cable Velcro (2 sets) A USB mouse is required to chaange system settings Mounting g and Insttallation Attaach the wireleess antenna as shown in lefft, screw antenna clockwisee onto the posst 1: [VESA moun nt]The player can be attach hed Mounting Option 1 the baack of screens or inside cabinetry with th he built in VESA (100m mmx100mm) compatible mo ounting flangee(screw threaad: to mounting posts on MIS‐D100 M4) 2: [Attach on the t back of th he Mounting Option 2 monitor using Velcro] o pads, and stiick on the botttom of playerr as shown in right. Stick the other Velcro o pads onto Separaate the Velcro the baack of monitorr, and then atttach the playeer to it. Use HDMI cable to connect playeer and the mo onitor 3.3. Port conn nections 3.4. System setup 1 INSTALLL a HDMI cabble to your monitor → When using HDMI, audio and video a sent over a single HDMI cable are INSTA ALL the AC po ower adapter → Immediateely, the Statuss LED on the main m unit lightts up SET your disp play to the HD DMI input → You should see the playyer boot up sccreen as show wn in right WAIT while player boots up → once you see “Basic seettings” on scrreen, the uration menu configu unit is read dy for contentt update or PLUG IN a USSB mouse to the t unit’s USB port Enter the corrresponding configuration option by movving the mousse cursor overr the configurration and clicck on the option to entter → (Wireless model only) U Using the USB B mouse, click on “Wireless LAN” to enter Wireless con nfiguration an nd provide security inforrmation to connect to yourr wireless acceess point → find and set the correctt time/date AN ND time zone.. IMPORTANT: time zone m must be set corrrectly in the menu or via management software for sscheduled playyback AL) Set a Passw word in the menus to preveent unauthorized changes. → (OPTIONA IMPORTANTT: Password will w be asked while enter thee setup menu during playback Click Set conttent button to o configure yo our signage ap ppliance to thee content servvice if needed → For advan nced player co onfiguration, such as static IP, display ressolution, and firmware update, visit www.digisign nage.com for more informaation 3.5. Content Management Pleasee consult the ssoftware docu umentation fo or information n specific to yo our managem ment solution. 3.6. Troubleshooting How do I interrupt playback and enter setup menu? You can move your mouse cursor to the corner of the screen, press and hold the left key for 10 seconds to exit playback and enter setup menu. Some video play jumpy or incorrectly, How to get best video playback performance? We provide video convert tool with pre‐configured profile for user to encode video to get best video playback performance. Visit www.digisignage.com to download video convert tool. Reset player to factory defaults (AC adapter is required) If modifying settings cause unintended results or if you have forgotten your password, please reset the player. Local contents will also be removed. 1. Press and hold the reset button with a pen. 2. Use AC adapter, re‐connect the power cord while holding reset button. 3. Wait until the orange status LED flashes, release reset to factory default state. button and wait for system to initialize Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna. ‐Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Karen_Huang Create Date : 2015:08:19 16:11:37+08:00 Modify Date : 2015:08:19 16:34:04+08:00 XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2015:08:19 16:34:04+08:00 Format : application/pdf Title : Microsoft Word - doc_XMP-6200_user-manual_2015-08-19.docx Creator : Karen_Huang Producer : Acrobat Distiller 15.0 (Windows) Document ID : uuid:46509ab6-a2d1-4fbe-aac9-e3d2c5ae463c Instance ID : uuid:53999d22-2be0-4b6c-a1da-07cab9728a05 Page Count : 9EXIF Metadata provided by EXIF.tools