ICOM orporated 277500 VHF Transceivers User Manual IC F3011 F3013 F4011 F4013 Instruction Manual

Download:
Mirror Download [FCC.gov]
Document ID	1866191
Application ID	f4HTBIYWHEMMl8S9GFqC3g==
Document Description	Updated User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	118.4kB (1480057 bits)
Date Submitted	2012-12-21 00:00:00
Date Available	2012-12-21 00:00:00
Creation Date	2012-06-08 08:49:42
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2012-12-17 09:39:20
Document Title	IC-F3011/F3013/F4011/F4013 Instruction Manual
Document Creator	Adobe InDesign CS3_J (5.0.4)
Document Author:	Icom Inc.

INSTRUCTION MANUAL
VHF TRANSCEIVERS
iF3011
iF3013
UHF TRANSCEIVERS
iF4011
iF4013
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition
that this device does not cause harmful interference.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy
during transmit mode. This radio is designed for and
classified as “Occupational Use Only”, meaning it must
be used only during the course of employment by individuals aware of the hazards, and the ways to minimize
W ARN ING
such hazards. This radio is NOT intended for use by the
“General Population” in an uncontrolled environment.
This radio has been tested and complies with the FCC
RF exposure limits for “Occupational Use Only”. In addition, your Icom
radio complies with the following Standards and Guidelines with regard
to RF energy and electromagnetic energy levels and evaluation of such
levels for exposure to humans:
• F CC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating
Compliance with FCC Guidelines for Human Exposure to Radio
Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992), IEEE Standard
for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous
Electromagnetic Fields– RF and Microwave.
• The following accessories are authorized for use with this product.
Use of accessories other than those specified may result in RF
exposure levels exceeding the FCC requirements for wireless RF
exposure.; Belt Clip (MB-94), Rechargeable Li-ion Battery Pack (BP230N/BP-232N/BP-232H) and Speaker-microphone (HM-131L).
C AU TIO N
To ensure that your expose to RF electromagnetic
energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as
this may damaged the radio and may also cause you to exceed FCC
RF exposure limits. A proper antenna is the antenna supplied with
this radio by the manufacturer or antenna specifically authorized by
the manufacturer for use with this radio.
• DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode.
Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “LED indicator” lights red. You can cause the radio
to transmit by pressing the “PTT” switch or VOX function.
• ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the
body when transmitting and only use the Icom belt-clip which is
listed on page 33 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded.
To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and
slightly off to one side.
The information listed above provides the user with the information
needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid such
interference, turn off the radio in areas where signs are posted to do so.
DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.
Occupational/Controlled Use
The radio transmitter is used in situations in which persons are exposed as
consequence of their employment provided those persons are fully aware
of the potential for exposure and can exercise control over their exposure.
ii
FOREWORD
READ ALL INSTRUCTIONS carefully and completely before
using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction
manual contains important operating instructions for the IC-F3011/
IC-F3013 vhf transceivers and IC-F4011/IC-F4013 uhf transceivers.
EXPLICIT DEFINITIONS
WORD
RDANGER!
RWARNING!
CAUTION
NOTE
DEFINITION
Personal death, serious injury or an explosion may occur.
Personal injury, fire hazard or electric shock
may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France,
Spain, Russia and/or other countries.
iii
PRECAUTIONS
R DANGER! NEVER short the terminals of the battery pack.
R DANGER! Use and charge only specified Icom battery packs
with Icom radios or Icom chargers. Only Icom battery packs are
tested and approved for use with Icom radios or charged with Icom
chargers. Using third-party or counterfeit battery packs or chargers
may cause smoke, fire, or cause the battery to burst.
R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body,
especially the face or eyes, while transmitting. The transceiver will
perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from
the lips and the transceiver is vertical.
R WARNING! NEVER operate the transceiver with a headset
or other audio accessories at high volume levels.
CAUTION: NEVER expose the transceiver to rain, snow or any
liquids. The transceiver may be damaged.
DO NOT push [PTT] when not actually desiring to transmit.
DO NOT use or place the transceiver in direct sunlight or in areas
with temperatures below –30°C (+22°F) or above +60°C (+140°F).
DO NOT modify the transceiver. The transceiver warranty does
not cover any problems caused by unauthorized modification.
MAKE SURE the flexible antenna and battery pack are securely
attached to the transceiver, and that the antenna and battery pack
are dry before attachment. Exposing the inside of the transceiver
to water will result in serious damage to the transceiver.
For U.S.A. only
CAUTION: Changes or modifications to this device, not expressly
approved by Icom Inc., could void your authority to operate this
transceiver under FCC regulations.
iv
TABLE OF CONTENTS
SAFETY TRAINING INFORMATION..................................................... i
FOREWORD........................................................................................iii
EXPLICIT DEFINITIONS......................................................................iii
PRECAUTIONS................................................................................... iv
TABLE OF CONTENTS........................................................................ v
1 ACCESSORIES.......................................................................... 1–5
■ Supplied accessories................................................................... 1
■ Accessory attachments............................................................... 2
2 PANEL DESCRIPTION............................................................. 6–11
■ Front, top and side panels........................................................... 6
■ LED indicator............................................................................... 8
■ Programmable function keys....................................................... 9
3 CONVENTIONAL OPERATION.............................................. 12–15
■ Turning power ON...................................................................... 12
■ Channel selection...................................................................... 12
■ Receiving and transmitting........................................................ 13
■ Setting the squelch level............................................................ 15
4 SIGNALING OPERATIONS.................................................... 16–17
■ Call procedure........................................................................... 16
■ Emergency Call......................................................................... 17
■ DTMF transmission.................................................................... 17
5 BATTERY CHARGING........................................................... 18–25
■ Caution...................................................................................... 18
■ Battery chargers........................................................................ 21
6 BATTERY CASE..................................................................... 26–27
■ Optional battery case (BP-240)................................................. 26
7 SWIVEL BELT CLIP............................................................... 28–31
■ MB-93 contents......................................................................... 28
■ To attach.................................................................................... 28
■ To detach................................................................................... 30
8 OPTIONS................................................................................ 32–35
9 FCC INFORMATION..................................................................... 36
ACCESSORIES
■ Supplied accessories
The following accessories are supplied.
Flexible
antenna*
Battery pack
Battery carger
(with AC adapter)
Belt clip
Jack cover (with screws)
10
11
12
13
*This illustration is described
with the VHF type.
14
15
16
17
18
19
20
1
ACCESSORIES
■ Accessory attachments
D Flexible antenna
Connect the supplied flexible antenna to
the antenna connector.
CAUTION:
• N EVER carry the transceiver by
holding only the antenna.
• DO NOT connect the antenna other
than listed on page 34.
• Transmitting without an antenna
may damage the transceiver.
ACCESSORIES
D Battery pack
To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direction
of the arrow (q), then lock it with the battery release button.
• Slide the battery pack until the battery release button makes a ‘click’
sound.
To remove the battery pack:
Push the battery release button in the direction of the arrow (w) as
shown below. The battery pack is then removed.
NOTE: Keep the battery terminals clean. It’s a good idea to occasionally clean them.
NEVER remove or attach the battery pack when the transceiver
is wet or soiled. This may result in water or dust getting into the
transceiver/battery pack and may result in the transceiver being
damaged.
10
11
12
13
14
15
16
17
18
Battery release
button
19
20
1
ACCESSORIES
D Jack cover
 ttach the jack cover when the optional speaker-microphone is not
used.
To attach the jack cover:
q Attach the jack cover to the
[SP MIC] connector.
w Tighten the screws.
To detach the jack cover:
e Remove the screws with a
phillips screwdriver.
r Detach the jack cover for the
optional equipment connection.
ACCESSORIES
D Belt clip
To attach the belt clip:
q Remove the battery pack if it is attached.
w Slide the belt clip in the direction of the arrow until the belt clip is
locked and makes a ‘click’ sound.
To detach the belt clip:
q Remove the battery pack if it is attached.
w Pinch the clip (q), and slide the belt clip in the direction of the
arrow (w).
10
11
12
13
14
15
16
17
18
19
20
2
PANEL DESCRIPTION
■ Front, top and side panels
Speaker
Microphone
q CHANNEL SELECTOR
	Rotate the channel selector to select the pre-programmed memory channels.
w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio level.
PANEL DESCRIPTION
e LED INDICATOR (p. 8)
➥ Lights red while transmitting.
➥ Lights green while receiving a signal, or when the squelch is
open.
➥ Lights/blinks orange when the matched 2/5-tone code is received, according to the pre-programming. (For IC-F3013/
F4013 only)
r SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone, earphone, etc.
[SP MIC] jack cover
NOTE: Attach the [SP MIC] jack
cover when the optional equipment is not used. (p. 4)
10
11
12
13
t DEALER-PROGRAMMABLE KEY [Lower]
The desired function can be assigned by your dealer. (p. 9)
14
y PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
16
u DEALER-PROGRAMMABLE KEY [Upper]
The desired function can be assigned by your dealer. (p. 9)
i ANTENNA CONNECTOR
Connects the supplied antenna.
15
17
18
19
20
2
PANEL DESCRIPTION
■ LED indicator
The LED indicator indicates several information
as follows;
(Ref.; R=Red, G=Green, O=Orange)
• TX: Turns Red while transmitting a signal.
• RX: Turns Green while receiving a signal.
• Fast/Slow scan: Blinks while Fast/Slow scan is activated.
can
• Low BATT1: You should charge the battery. (blinks slowly)
B AT T1
• Low BATT2: You must charge the battery. (blinks fast)
B AT T2
• TX low BATT2: Low BATT2 was detected during TX mode.
w BATT 2
• CH error: Non-programmed channel is selected.
R O R O R O R O R O R O R O R O
For IC-F3013/IC-F4013 only
• Call LED (ON): When receiving a matched 2/5-tone.
O O
ED ON
• Call LED (Blink): When receiving a matched 2/5-tone.
E D Bl i nk
PANEL DESCRIPTION
■ Programmable function keys
The following functions can be assigned to [Upper] and [Lower]
programmable function keys.
Consult your Icom dealer or system operator for details concerning
your transceivers programming.
D For All models
SCAN A KEY
➥ Push to start and cancel scanning operation.
➥ When the Power ON scan function is turned ON, push to pause
the scanning operation. The paused scan restarts after the specified time period has passed.
SCAN B KEY
Push to start and cancel scanning operation. In case of transmission during scan, pauses scanning. The paused scan restarts after
the specified time period has passed.
10
PRIORITY CHANNEL KEYS
➥ Push to select the Priority A or Priority B channel.
➥P
 ush and hold [Prio A (Rewrite)] to rewrite the Prio A channel.
13
MR-CH 1/2/3/4 KEYS
Push to select a memory channels 1 to 4 directly.
11
12
14
15
16
17
18
19
20
2
PANEL DESCRIPTION
OUTPUT POWER SELECTION KEY
Select the transmit output power temporarily or permanently, depending on the pre-setting.
• Ask your dealer for the output power level for each selection.
TALK AROUND KEY
➥ Push to turn the talk around function OFF.
➥ Push and hold to turn the talk around function ON.
• The talk around function equalizes the transmit frequency to the
receive frequency for transceiver-to-transceiver communication.
WIDE/NARROW KEY
➥ Push to select the IF bandwidth to wide.
• The wide passband width can be selected from 25 or 20 kHz using
the optional cloning software (PMR operation only). Ask your dealer
for details.
➥ Push and hold to select the IF bandwidth to narrow.
SIREN KEY
Push to emit a siren. This function can be used for situations other
than an emergency alert such as a security alarm for example.
LOCK KEY
Push and hold to electronically lock all programmable keys except
the followings: [Moni(Audi)], [Call] (incl. Call A and Call B)* and
[Emergency Single]/[Emergency Repeat] (incl. Silent)*.
* Available for IC-F3013/IC-F4013 only.
10
PANEL DESCRIPTION
MONITOR KEY
➥ Push to mute and release the CTCSS (DTCS) or 2Tone* squelch
mute. Open any squelches/deactivate any mutes while pushing
this key. (LMR operation only)
* Available for the IC-F3013/F4013 only.
➥ Activates one of (or two of) the following functions on each channel independently: (PMR operation only)
• Push and hold to un-mute the channel (audio is emitted; ‘Audible’).
• Push to mute the channel (audio is not emitted; ‘Inaudible’).
• Push to send a ‘reset code’ after the communication is finished.
NOTE: The un-mute condition (‘Audible’ condition) may automatically return to the mute condition (‘Inaudible’ condition)
after a specified period.
D For IC-F3013/IC-F4013 only
DTMF AUTODIAL KEY
Push to transmit the programmed DTMF code.
10
CALL KEYS
Push to transmit a 2/5-tone code.
12
• Call transmission is necessary before you call another station depending on your signalling system.
• [Call A] and/or [Call B] keys may be available when your system employs selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.
14
EMERGENCY SINGLE/EMERGENCY REPEAT KEYS
➥P
 ush and hold for the specified time period to transmit an emergency call once or repeatedly.
➥W
 hen [Emergency Single (Silent)] or [Emergency Repeat (Silent)]
is pushed, an emergency call is transmitted with no beep emission.
• If you want to cancel the emergency call, push (or push and hold)
the key again before transmitting the call.
• The emergency call is transmitted one time only or repeatedly until
receiving a control code depending on the pre-setting.
11
13
15
16
17
18
19
20
11
3
CONVENTIONAL OPERATION
■ Turning power ON
Rotate [VOL] to turn power ON.
[VOL]
■ Channel selection
Rotate [CHANNEL SELECTOR] to select the desired operating channel, in
sequence; or, push one of [MR-CH 1] to
[MR-CH 4] key to select a channel directly.
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this
type. When turning the power ON, the
transceiver automatically starts scanning.
Scanning stops when receiving a call.
12
[CHANNEL
SELECTOR]
CONVENTIONAL OPERATION
■ Receiving and transmitting
NOTE: Transmitting without an antenna may damage the transceiver. See page 2 for antenna attachment.
Receiving:
q Rotate [VOL] to turn power ON.
w Rotate [CHANNEL SELECTOR] or push one of [MR-CH 1] to
[MR-CH 4] key to select a channel.
e When receiving a call, adjust the audio output level to a comfortable listening level.
Transmitting:
Wait for the channel to become clear to avoid interference.
q While pushing and holding [PTT], speak into the microphone at
a normal voice level.
w Release [PTT] to return to receive.
IMPORTANT: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your
mouth, then speak into the microphone at a normal voice
level.
10
11
12
13
14
15
16
17
18
19
20
13
3
CONVENTIONAL OPERATION
D Transmitting notes
• Transmit inhibit function
The transceiver has several inhibit functions which restrict transmission under the following conditions:
- The channel is in mute condition.
- The channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a ‘receive only’ channel.
• Time-out timer
After continuous transmission for the pre-programmed time period, the
time-out timer activates, and causes the transceiver to stop transmitting.
• Penalty timer
Once the time-out timer activates, transmission is further inhibited
for a period determined by the penalty timer.
14
CONVENTIONAL OPERATION
■ Setting the squelch level
The squelch circuit mutes the received audio signal depending on
the signal strength.
q While pushing [PTT] and [Lower],
rotate [VOL] to turn the power ON
to enter the squelch level adjustment mode.
w P ush [Upper] to increase the
squelch level (tight squelch) or
[Lower] to decrease the squelch
level (loose squelch).
e Rotate [VOL] to turn the power
OFF to fix the squelch level.
[VOL]
[Upper]
[PTT]
[Lower]
10
11
12
13
14
15
16
17
18
19
20
15
4
SIGNALING OPERATIONS
NOTE: The tone signalling operations are available for the
IC-F3013/F4013 only.
■ Call procedure
When your system employs tone signalling (excluding CTCSS and
DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling
system which allows you to call specific station(s) only and prevent
unwanted stations from contacting you.
q Select the desired TX code channel or 2/5-tone code according
to your System Operator’s instructions.
• This may not be necessary depending on programming.
w Push [Call]. (p. 11)
e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion.
Selective calling
Non-selective calling
D Transmitting notes— PTTID call
16
The transceiver sends the ID code (5-tone, DTMF or digital ANI)
automatically when [PTT] is pushed (beginning of transmission)
and released (end of transmission) depends on the setting.
SIGNALING OPERATIONS
■ Emergency Call
When [Emergency Single] or [Emergency Repeat] (p. 11) is
pushed and held for the specified time period, the emergency signal (5-tone, DTMF or MDC 1200) is transmitted once or repeatedly
on the emergency channel. A repeat emergency signal is automatically transmitted until it receives the acknowledgement signal.
When no emergency channel is specified, the signal is transmitted
on the previously selected channel.
If you want to cancel the emergency call, push and hold the key
again before transmitting the call.
The emergency call can be transmitted without a beep emission,
and the LCD indication if [Emergency Single (Silent)] or [Emergency Repeat (Silent)] (p. 11) is pushed.
The transceiver can also be programmed to keep the microphone
open during an emergency call, allowing monitoring of the situation.
IMPORTANT: It is recommended to set an emergency channel
individually to provide the certain emergency call operation.
10
11
12
13
14
15
■ DTMF transmission
16
If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available.
17
➥P
 ush [DTMF Autodial] to transmit the DTMF code.
19
18
20
17
5
BATTERY CHARGING
■ Caution
Misuse of Lithium-ion batteries may result in the following
hazards: smoke, fire, or the battery may rupture. Misuse can
also cause damage to the battery or degradation of battery
performance.
R DANGER! Use and charge only specified Icom battery packs
with Icom radios or Icom charger. Only Icom battery packs are
tested and approved for use and charge with Icom radios or Icom
charger. Using third-party or counterfeit battery packs or charger
may cause smoke, fire, or cause the battery to burst.
D Battery caution
R DANGER! DO NOT hammer or otherwise impact the battery. Do
not use the battery if it has been severely impacted or dropped, or if
the battery has been subjected to heavy pressure. Battery damage
may not be visible on the outside of the case. Even if the surface
of the battery does not show cracks or any other damage, the cells
inside the battery may rupture or catch fire.
R DANGER! NEVER use or leave battery packs in areas with
temperatures above +60˚C (+140˚F). High temperature buildup in
the battery, such as could occur near fires or stoves, inside a sun
heated car, or in direct sunlight may cause the battery to rupture or
catch fire. Excessive temperatures may also degrade battery performance or shorten battery life.
R DANGER! DO NOT expose the battery to rain, snow, seawater,
or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. The battery is not
waterproof.
18
BATTERY CHARGING
R DANGER! NEVER incinerate used battery packs since internal
battery gas may cause them to rupture, or may cause an explosion.
R DANGER! NEVER solder the battery terminals or NEVER modify the battery pack. This may cause heat generation, and the battery may rupture, emit smoke or catch fire.
R DANGER! Use the battery only with the transceiver for which it
is specified. Never use a battery with any other equipment, or for
any purpose that is not specified in this instruction manual.
R DANGER! If fluid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing
them, and see a doctor immediately.
WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these
conditions occur, contact your Icom dealer or distributor.
10
WARNING! Immediately wash, using clean water, any part of the
body that comes into contact with fluid from inside the battery.
12
WARNING! NEVER put the battery in a microwave oven, highpressure container, or in an induction heating cooker. This could
cause a fire, overheating, or cause the battery to rupture.
14
CAUTION! Always use the battery within the specified temperature
range for the transceiver (–30˚C to +60˚C; –22˚F to +140˚F) and
the battery itself (–20˚C to +60˚C; –4˚F to +140˚F). Using the battery out of its specified temperature range will reduce the battery’s
performance and battery life.
11
13
15
16
17
18
19
20
19
5
BATTERY CHARGING
CAUTION! Shorter battery life could occur if the battery is left fully
charged, completely discharged, or in an excessive temperature
environment (above +50˚C; +122˚F) for an extended period of time.
If the battery must be left unused for a long time, it must be detached from the radio after discharging.
You may use the battery until the remaining capacity is about half, then
keep it safely in a cool dry place with the temperature range as below:
–20˚C to +50˚C (–4˚F to +122˚F)
(within a month)
–20˚C to +40˚C (–4˚F to +95˚F)
(within three months)
–20˚C to +20˚C (–4˚F to +68˚F)
(within a year)
D Charging caution
R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near fires or stoves, inside
a sun heated car, or in direct sunlight. In such environments, the
safety/protection circuit in the battery will activate, causing the battery to stop charging.
WARNING! DO NOT charge or leave the battery in the battery
charger beyond the specified time for charging. If the battery is not
completely charged by the specified time, stop charging and remove the battery from the battery charger. Continuing to charge the
battery beyond the specified time limit may cause a fire, overheating, or the battery may rupture.
WARNING! NEVER insert the transceiver (battery attached to the
transceiver) into the charger if it is wet or soiled. This could corrode
the battery charger terminals or damage the charger. The charger
is not waterproof.
CAUTION! DO NOT charge the battery outside of the specified
temperature range: BC-160 (0˚C to +40˚C; +32˚F to +104˚F). Icom
recommends charging the battery at +20˚C (+68˚F). The battery
may heat up or rupture if charged out of the specified temperature
range. Additionally, battery performance or battery life may be reduced.
20
BATTERY CHARGING
■ Battery chargers
D Rapid charging with the BC-160
The optional BC-160 provides rapid charging of the Li-ion battery
pack. Charging period: Approximately 3 hours (with BP-232H)
The following items are additionally required:
• An AC adapter (not supplied with some versions) or the DC power
cable (OPC-515L/CP-23L) is additionally required.
AC adapter
(A different type, or no AC adapter is
supplied, depending on the version.)
Battery pack
Transceiver
Turn power OFF
10
11
12
Optional OPC-515L*
(for power source) or
CP-23L (for 12 V cigarette lighter socket)
can be used instead
of the AC adapter.
* About OPC-515L
White line:
Black line :
13
14
15
16
17
IMPORTANT!
Ensure the guide tabs on the
battery pack are correctly
aligned with the guide rails
inside the charger adapter.
Tabs
18
19
20
Guide rail
21
5
BATTERY CHARGING
D Regular charging with the BC-171
The optional BC-171 provides regular charging of the Li-ion battery
pack.
Charging period: Approximately 10 hours (with BP-232H)
The following items are additionally required:
• An AC adapter (not supplied with some versions) or the DC power
cable (OPC-515L/CP-23L) is additionally required.
AC adapter
(A different type, or no AC adapter is
supplied, depending on the version.)
Battery pack
Transceiver
Turn power OFF
Optional OPC-515L*
(for power source) or
CP-23L (for 12 V cigarette lighter socket)
can be used instead
of the AC adapter.
* About OPC-515L
White line:
Black line :
IMPORTANT!
Ensure the guide tabs on the
battery pack are correctly
aligned with the guide rails
inside the charger adapter.
Guide rail
22
Tabs
BATTERY CHARGING
D AD-106 installation
The AD-106 charger adapter must be installed into the BC-119N
or BC-121N before battery charging.
q Attach the plugs from the BC-119N/BC-121N to the AD-106
charger adapter.
w Secure the AD-106 into the holder space of the BC-119N/BC121N with the supplied screws.
Plugs
Desktop charger
adapter
10
Sockets
11
12
13
Screws supplied
with the charger
adapter
14
15
16
17
18
19
20
This illustration is described with the BC-119N.
23
5
BATTERY CHARGING
D Rapid charging with the BC-119N+AD-106
The optional BC-119N provides rapid charging of the Li-ion battery
pack.
Charging period: Approximately 3 hours (with BP-232H)
The following items are additionally required:
• An AD-106 charger adapter (purchase separately)
• An AC adapter (not supplied with some versions) or the DC power
cable (OPC-515L/CP-23L).
Transceiver
Turn power OFF
AC adapter
(A different type, or no AC
adapter is supplied, depending on the version.)
Battery pack
AD-106 charger
adapter is installed
in BC-119N.
Optional OPC-515L*
(for power source) or
CP-23L (for 12 V cigarette lighter socket)
can be used instead
of the AC adapter.
* About OPC-515L
White line:
Black line :
IMPORTANT!
Ensure the guide tabs on the
battery pack are correctly
aligned with the guide rails
inside the charger adapter.
Guide rails
24
Tabs
BATTERY CHARGING
D Rapid charging with the BC-121N+AD-106
The optional BC-121N allows up to 6 battery packs to be charged
simultaneously.
Charging period: Approximately 3 hours (with BP-232H)
The following items are additionally required.
• Six AD-106 charger adapter (purchase separately)
• An AC adapter (BC-157) or the DC power cable (OPC-656)
Turn power OFF
Battery pack
Transceiver
AD-106 charger
adapters are installed
in each slot.
10
AC adapter
(Purchase
separately)
11
12
13
14
15
16
DC power cable
(OPC-656*)
(Connect with a DC
power supply; 13.8 V/at
least 7 A)
*About the OPC-656
Red line: Black line:
IMPORTANT!
Ensure the guide tabs
on the battery pack are
correctly aligned with
the guide rails inside
the charger adapter.
Guide rails
Tabs
17
18
19
20
25
6
BATTERY CASE
■ Optional battery case (BP-240)
When using the optional battery case, install 6 × AAA (LR03) size
alkaline batteries as illustrated at right.
q Unhook the battery cover release hook (q), and open the cover
in the direction of the arrow (w). (Fig.1)
w Then, install 6 × AAA (LR03) size alkaline batteries. (Fig.2)
• Install the alkaline batteries only.
• Be sure to observe the correct polarity.
e Fit the cover in the direction of the arrow (e), then close (r).
Hook the battery cover release hook until it makes a ‘click’ sound
(t). (Fig.3)
CAUTION:
• When installing batteries, make sure they are all the same
brand, type and capacity. Also, do not mix new and old batteries together.
• Keep battery contacts clean. It’s a good idea to occasionally
clean them.
• Never incinerate used battery cells since internal battery gas
may cause them to rupture.
• Never expose a detached battery case to water. If the battery
case gets wet, be sure to wipe it dry before using it.
NOTE: When the optional battery case is attached, the battery
type must be selected to “Alkaline battery operation” when turning the transceiver ON. Ask your dealer for details.
26
BATTERY CASE
Fig.1
BP-240
Fig.2
10
11
12
13
Fig.3
14
15
16
17
18
19
20
27
7
SWIVEL BELT CLIP
■ MB-93 contents
Qty.
q Belt clip..................................................................................... 1
w Base clip................................................................................... 1
■ To attach
q Remove the battery pack if it is attached. (p. 3)
w Slide the base clip in the direction of the arrow until the base clip
is locked and makes a ‘click’ sound.
28
SWIVEL BELT CLIP
e Clip the belt clip to a part of your belt. And insert the transceiver
into the belt clip until the base clip inserted fully into the groove.
10
11
r Once the transceiver is locked in place, it swivels as illustrated
below.
12
13
14
15
16
17
18
19
Once the transceiver is locked in place,
it will swivel 360 degrees.
20
29
7
SWIVEL BELT CLIP
■ To detach
q Turn the transceiver upside down in the direction of the arrow
and pull out from the belt clip.
30
SWIVEL BELT CLIP
w Remove the battery pack if it is attached. (p. 3)
e Pinch the clip (q), and slide the base clip in the direction of the
arrow (w).
CAUTION:
HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR
DETACHING THE TRANSCEIVER FROM THE BELT CLIP.
Otherwise the transceiver may not be attached to the holder or
swivel properly if the transceiver is accidentally dropped and the
base clip is scratched or damaged.
10
11
12
13
14
15
16
17
18
19
20
31
8
OPTIONS
D BATTERY PACK
Battery pack
Voltage
Capacity
Battery life*1
BP-230N
7.4 V
950 mAh (min.)
980 mAh (typ.)
9 hrs.
BP-232N
7.4 V
1900 mAh (min.)
2000 mAh (typ.)
18 hrs.
BP-232H
7.4 V
2250 mAh (min.)
2300 mAh (typ.)
21 hrs.
BP-240
Battery case for AAA
(LR03) × 6 alkaline
—*2
*1	When the power save function is turned ON, and the operating periods are calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2 Operating period depends on the alkaline cells used.
D CHARGERS
• BC-119N desktop charger + AD-106 charger adapter
+ BC-145S ac adapter
	For rapid charging of battery packs. An AC adapter is supplied
with the charger depending on versions.
Charging time: Approximately 3 hours when BP-232H is attached.
• BC-121N multi-charger + AD-106 charger adapter (6 pcs.)
+ BC-157 ac adapter
	For rapid charging of up to 6 battery packs (six AD-106’s are required)
simultaneously. An AC adapter should be purchased separately.
Charging time: Approximately 3 hours when BP-232H is attached.
32
OPTIONS
• BC-160 desktop charger + BC-145S ac adapter
	For rapid charging of battery packs. An AC adapter is supplied
with the charger depending on versions.
Charging time: Approximately 3 hours when BP-232H is attached.
•	BC-171 desktop charger + BC-147S ac adapter
	For regular charging of battery packs. We recommend that the
BP-230N charging. An AC adapter is supplied with the charger
depending on versions.
Charging time: Approximately 11 hours when BP-232H is attached.
Approximately 4 hours when BP-230N is attached.
D BELT CLIPS
• MB-93 swivel belt clip
• MB-94 belt clip
	Exclusive alligator-type belt clip.
• MB-96N/96F leather belt hanger
D DC CABLES
• CP-23L cigarette lighter cable
Allows charging of the battery pack through a 12 V cigarette lighter
socket. (For BC-119N/BC-160/BC-171)
• OPC-515L/OPC-656 dc power cables
	Allows charging of the battery pack using a 13.8 V power source
instead of the AC adapter.
OPC-515L: For BC-119N/BC-160/BC-171
OPC-656 : For BC-121N
10
11
12
13
14
15
16
17
18
19
20
33
8
OPTIONS
D ANTENNAS
• FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas
FA-SC73US: 450–490 MHz
FA-SC56VS: 150–162 MHz
FA-SC57VS: 160–174 MHz
• FA-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/
FA-SC55V antennas
FA-SC01U: 350–400 MHz
FA-SC25U: 400–430 MHz
FA-SC57U: 430–470 MHz
FA-SC72U: 470–520 MHz
FA-SC25V: 136–155 MHz
FA-SC55V: 146–174 MHz
• FA-SC61VC/FA-SC61UC cut antennas
FA-SC61VC: 136–174 MHz
FA-SC61UC: 380–520 MHz
D OTHER OPTIONS
• SP-13 earphone
	Provides clear receive audio in noisy environment.
• HM-153L earphone-microphone
• HM-131L/158L/159L speaker-microphone
	Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt.
• VS-1L vox/ptt case + HS-94/HS-95/HS-97 headset
VS-1L: VOX/PTT switch box for hands-free operation, etc.
HS-94: Ear hook type
HS-95: Neck-arm type
HS-97: Throat microphone
• MB-130 vehicle charger bracket
Vehicle mounting bracket for the BC-160 battery charger.
Approved Icom optional equipment is designed for optimal performance
when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is
not manufactured or approved by Icom.
34
Some options may not be available in some countries. Please ask your
dealer for details.
OPTIONS
D About VS-1L vox/ptt case
The VS-1L is a VOX/PTT unit for Icom handheld transceivers, and
allows you hands-free operation.
An optional headset (HS-94, etc.) is additionally required for operation.
• The VOX (voice operated transmission) function starts transmission
without pushing PTT switch when you speak into the microphone;
then, automatically returns to receive when you stop speaking.
Features
➥ Straight type head SP/MIC plug equipped
➥ Water resistant construction
➥ Durable construction
➥ Equipped with a PTT switch and revolving clip.
MIC/VOX gain adjustment
1 Remove the water protection cover on the right side of the VS-1L.
2 Adjust the MIC/VOX gain with a thin screw driver. Clockwise rotation increases the MIC/VOX gain.
3 Return the protective cover back to the MIC/VOX gain adjustment
hole.
Adjusting pot
10
11
12
13
14
VS-1L
PTT switch
15
16
Water protection cover
VOX
PTT
17
18
19
20
35
9
FCC INFORMATION
• FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
36
MEMO
10
11
12
13
14
15
16
17
18
19
20
MEMO
MEMO
10
11
12
13
14
15
16
17
18
19
20
MEMO
MEMO
10
11
12
13
14
15
16
17
18
19
20
A-6768H-1EX-w
Printed in Japan
© 2009–2012 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Author                          : Icom Inc.
Create Date                     : 2012:06:08 08:49:42+09:00
Modify Date                     : 2012:12:17 09:39:20-05:00
Subject                         : VHF/UHF Transceivers
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:7259f80d-2a57-4ec5-befe-15d8a97d260d
Document ID                     : adobe:docid:indd:bff006ca-aab0-11e1-b231-ac4c6f72b306
Rendition Class                 : proof:pdf
Derived From Instance ID        : bff006c9-aab0-11e1-b231-ac4c6f72b306
Derived From Document ID        : adobe:docid:indd:ec305ffe-5189-11de-8f5c-c4686eec8d61
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:5FC5790D692DDE119EC690B9A9B87354, uuid:4C0694347F2DDE11A45F971CEFBBBD76, uuid:BC51B7EB722DDE118FEF8988ADCAC25A, uuid:9841AA617B2DDE11A45F971CEFBBBD76, uuid:98D191AC672DDE118FEF8988ADCAC25A, uuid:4D0694347F2DDE11A45F971CEFBBBD76, uuid:4B0694347F2DDE11A45F971CEFBBBD76, uuid:BB51B7EB722DDE118FEF8988ADCAC25A, uuid:99D191AC672DDE118FEF8988ADCAC25A, uuid:3D8D767CF82ADE118D46C59EC9EC1123, uuid:9ED191AC672DDE118FEF8988ADCAC25A, uuid:BD51B7EB722DDE118FEF8988ADCAC25A, uuid:BE51B7EB722DDE118FEF8988ADCAC25A, uuid:C251B7EB722DDE118FEF8988ADCAC25A, uuid:12DA6704BFABE111BCD39D5839E94204, uuid:D4C25CFEABABE1118D86CAFCEF472525, uuid:D3C25CFEABABE1118D86CAFCEF472525, uuid:D5C25CFEABABE1118D86CAFCEF472525, uuid:0E9F2BECB2ABE1118D86CAFCEF472525, uuid:0D9F2BECB2ABE1118D86CAFCEF472525, uuid:C33F8C6BD3EDDD11BCCE9822886ADACD, uuid:530694347F2DDE11A45F971CEFBBBD76, uuid:6571508A7B29DE11974EC4A7891D3A7F, uuid:92293C1A2D2EDE11A114E2A7BA021010, uuid:96293C1A2D2EDE11A114E2A7BA021010, uuid:3E5EE455842DDE11A45F971CEFBBBD76, uuid:540694347F2DDE11A45F971CEFBBBD76
Manifest Reference Document ID  : uuid:660EE9B3682DDE119EC690B9A9B87354, uuid:02B2F42B99EDDD11BCCE9822886ADACD, uuid:04B2F42B99EDDD11BCCE9822886ADACD, uuid:9741AA617B2DDE11A45F971CEFBBBD76, uuid:08B2F42B99EDDD11BCCE9822886ADACD, uuid:1DFB25BECFEDDD11BCCE9822886ADACD, uuid:1BFB25BECFEDDD11BCCE9822886ADACD, uuid:1FFB25BECFEDDD11BCCE9822886ADACD, uuid:21FB25BECFEDDD11BCCE9822886ADACD, uuid:3A8D767CF82ADE118D46C59EC9EC1123, uuid:9DD191AC672DDE118FEF8988ADCAC25A, uuid:5C71508A7B29DE11974EC4A7891D3A7F, uuid:B2D20F8F6229DE11974EC4A7891D3A7F, uuid:C151B7EB722DDE118FEF8988ADCAC25A, uuid:23FB25BECFEDDD11BCCE9822886ADACD, uuid:ACD20F8F6229DE11974EC4A7891D3A7F, uuid:AED20F8F6229DE11974EC4A7891D3A7F, uuid:6CD11BABD2EDDD11BCCE9822886ADACD, uuid:70D11BABD2EDDD11BCCE9822886ADACD, uuid:C03F8C6BD3EDDD11BCCE9822886ADACD, uuid:C23F8C6BD3EDDD11BCCE9822886ADACD, uuid:C43F8C6BD3EDDD11BCCE9822886ADACD, uuid:6471508A7B29DE11974EC4A7891D3A7F, uuid:91293C1A2D2EDE11A114E2A7BA021010, uuid:3C5EE455842DDE11A45F971CEFBBBD76, uuid:C63F8C6BD3EDDD11BCCE9822886ADACD, uuid:C83F8C6BD3EDDD11BCCE9822886ADACD
Metadata Date                   : 2012:12:17 09:39:20-05:00
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8866 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : IC-F3011/F3013/F4011/F4013 Instruction Manual
Creator                         : Icom Inc.
Description                     : VHF/UHF Transceivers
Light Source                    : Unknown
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Mode                       : UseOutlines
Page Count                      : 48

EXIF Metadata provided by EXIF.tools