ICOM orporated 340202 UHF TRANSCEIVER User Manual IC F3161 F4161 Instruction Manual

ICOM Incorporated UHF TRANSCEIVER IC F3161 F4161 Instruction Manual

Contents

User Manual

Download: ICOM orporated 340202 UHF TRANSCEIVER User Manual IC F3161 F4161 Instruction Manual
Mirror Download [FCC.gov]ICOM orporated 340202 UHF TRANSCEIVER User Manual IC F3161 F4161 Instruction Manual
Document ID1710621
Application IDlYIksIv8gt8u1P1SeFrnpQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize341.48kB (4268509 bits)
Date Submitted2012-05-30 00:00:00
Date Available2012-10-01 00:00:00
Creation Date2017-10-31 11:55:09
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-31 11:55:09
Document TitleIC-F3161/F4161 Instruction Manual
Document CreatorAdobe InDesign CS3_J (5.0.4)
Document Author: Icom Inc.

INSTRUCTION MANUAL
UHF TRANSCEIVERS
iF4260
Series
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that
this device does not cause harmful interference.
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL — This
instruction manual contains important operating instructions
for the IC-F4261DT/DS, IC-F4263DT/DS UHF TRANSCEIVERS.
This instruction manual includes some functions which are
usable only when they are preset by your dealer. Ask your
dealer for details.
See the operating guide for details of IDAS™, BIIS, MDC
and LTR® system operations. Ask your dealer for details.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
IDAS is trademark of Icom Incorporated (Japan).
LTR is a registered trademark of the E.F.Johnson Technologies, INC. in the
United States.
All other products or brands are registered trademarks or trademarks of their
respective holders.
EXPLICIT DEFINITIONS
WORD
DEFINITION
RDANGER!
Personal death, serious injury or an explosion may occur.
RWARNING!
Personal injury, fire hazard or electric
shock may occur.
CAUTION
NOTE
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed solely
for use within this Communications Equipment. The user of
this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble
the Object Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos.
#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365,
#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
#5,247,579, #5,226,084 and #5,195,166.
PRECAUTIONS
R DANGER! NEVER short the terminals of the battery
pack.
R DANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or
charged with Icom chargers. Using third-party or counterfeit
battery packs or chargers may cause smoke, fire, or cause
the battery to burst.
R WARNING! NEVER hold the transceiver so that
the antenna is very close to, or touching exposed parts of
the body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is vertical.
R WARNING! NEVER operate the transceiver with
a headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
R WARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
CAUTION: MAKE SURE the flexible antenna, battery pack and jack cover are securely attached to the transceiver, and that the antenna and battery pack are dry before
attachment. Exposing the inside of the transceiver to dust or
water will result in serious damage to the transceiver.
DO NOT operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere.
DO NOT push [PTT] when not actually intending to transmit.
DO NOT use or place the transceiver in direct sunlight or
in areas with temperatures below –30°C (–22°F) or above
+60°C (+140°F).
The basic operations, transmission and reception of the transceiver are guaranteed within the specified operating temperature range. However, the LCD display may not be operate
correctly, or show an indication in the case of long hours of
operation, or after being placed in extremely cold areas.
DO NOT modify the transceiver. The transceiver warranty does
not cover any problems caused by unauthorized modification.
DO NOT use harsh solvents such as benzine or alcohol
when cleaning, as they will damage the transceiver surfaces.
BE CAREFUL! The transceiver will become hot when
operating it continuously for long periods of time.
ii
PRECAUTIONS (Continued)
FCC INFORMATION
BE CAREFUL! The transceiver meets IP67 requirements for dust-tight and waterproof protection. However, once
the transceiver has been dropped, dust-tight and waterproof
protection cannot be guaranteed because of possible damage to the transceiver’s case or the waterproof seal.
•฀FOR฀CLASS฀A฀UNINTENTIONAL฀RADIATORS:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or batteries from
the transceiver when not using it for a long time. Otherwise,
the installed battery pack or batteries will become exhausted,
and will need to be recharged or replaced.
MAKE SURE to turn OFF the transceiver power before
connecting the supplied/optional equipment.
•฀฀The฀GPS฀receiver฀may฀not฀work฀if฀the฀transceiver฀transmits฀
near the 510 MHz. This is made in the internal circuit and
does not indicate a transceiver malfunction.
iii
CAUTION: Changes or modifications to this transceiver, not
expressly approved by Icom Inc., could void your authority
to operate this transceiver under FCC regulations.
TABLE OF CONTENTS
IMPORTANT .......................................................................... i
EXPLICIT DEFINITIONS ....................................................... i
VOICE CODING TECHNOLOGY .......................................... i
PRECAUTIONS .................................................................... ii
FCC INFORMATION ........................................................... iii
TABLE OF CONTENTS ....................................................... iv
1 ACCESSORIES ...........................................................1–3
■ Supplied accessories ...................................................1
■ Accessory attachments ................................................1
2 PANEL DESCRIPTION..............................................4–10
■ Front panel ...................................................................4
■ Function display ...........................................................5
■ Programmable function keys ........................................6
3 BASIC OPERATION ................................................11–18
■ Turning power ON ......................................................11
■ Channel selection ......................................................12
■ Call procedure ............................................................13
■ User set mode ............................................................16
■ Scrambler function .....................................................16
■ Stun function ..............................................................16
■ Emergency transmission ............................................17
■ Man Down Emergency Call........................................17
■ Automatic Key Lock function ......................................18
■ Priority A channel selection........................................18
4 BATTERY CHARGING ............................................19–23
■ Caution.......................................................................19
■ Optional battery chargers...........................................21
5 BATTERY CASE............................................................24
■ Optional battery case (BP-240)..................................24
6 SWIVEL BELT CLIP ................................................25–26
■ MB-93 contents ..........................................................25
■ To attach ....................................................................25
■ To detach ...................................................................26
7 SPEAKER MICROPHONE ............................................27
■ Optional HM-184 ........................................................27
■ To attach ....................................................................27
8 OPTIONS .................................................................28–29
9 SAFETY TRAINING INFORMATION .......................30–31
10
11
12
13
14
15
16
iv
1
ACCESSORIES
■ Supplied accessories
■ Accessory attachments
The following accessories are supplied.
D Flexible antenna
Flexible antenna
Battery pack
Belt clip
(This illustration is
for the UHF type.)
Connector cover
(with screw)
NOTE: Some accessories are not supplied, depending on
the transceiver version.
Connect the supplied flexible antenna
to the antenna connector.
CAUTION:
฀•฀฀NEVER carry the transceiver by
holding antenna.
฀•฀DO NOT connect any antenna
other than those listed on page
29.
฀•฀Transmitting without an antenna
will damage the transceiver.
ACCESSORIES
D Battery pack
D Belt clip
To attach the battery pack:
Slide the battery pack in the direction of the arrow (q) until the
battery release button makes a ‘click’ sound.
NOTE: Push on the bottom of the pack to make sure the
release button is firmly locked.
To attach the belt clip:
q Release the battery pack if it is attached.
w Slide the belt clip in the direction of the arrow until the belt
clip locks and makes a ‘click’ sound.
To release the battery pack:
Push the battery release button in the direction of the arrow
(w), as shown below. The battery pack is then released.
NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result water or dust getting into the transceiver/battery pack and may result in the
transceiver being damaged.
To detach the belt clip:
q Release the battery pack if it is attached.
w Pinch the clip (q), and slide the belt clip in the direction of
the arrow (w).
Battery pack
10
11
12
13
14
15
16
Battery release
button
NOTE: Keep the battery pack terminals clean. It’s a good
idea to regularly clean them.
1
ACCESSORIES
D Connector cover
To attach the connector cover:
To detach the connector cover:
q Place the connector cover over the multi-connector.
w Tighten the screw.
q Unscrew the screw using a Phillips screwdriver.
w Detach the connector cover to connect optional equipment.
Multiconnector
Connector
cover
CAUTION:
Attach the connector cover when optional equipment is not
used. Otherwise the terminals of the multi-connector may
short out, and this could damage the transceiver.
PANEL DESCRIPTION
■ Front panel
!2
GPS receiver*
!1
Speaker
!0
Microphone
r DEALER-PROGRAMMABLE KEY [Side1]
฀ ฀Desired functions can be preset by your dealer.
(p. 6)
t PTT SWITCH [PTT]
฀ Hold down to transmit, release to receive.
y DEALER-PROGRAMMABLE KEYS [Side2]/[Side3]
฀ ฀Desired functions can be preset by your dealer. (p. 6)
u 10-KEYPAD (Depending on the version)
฀ ฀The keypad allows you to enter digits to:
฀
฀
฀
฀
฀
*A GPS receiver is
bult-in, depending on
the transceiver version.
q ROTARY SELECTOR
฀ ฀Rotate to select the memory channels or the operating
zone, depending on the presetting.
w ANTENNA CONNECTOR
฀ Connect the supplied antenna. (p. 1)
•฀Select฀memory฀channels
•฀Select฀tone฀channels
•฀Select฀DTMF฀codes฀(during฀transmit)
•฀Set฀TX฀codes
•฀Start฀up฀with฀the฀password
i DEALER-PROGRAMMABLE KEYS [P0] to [P3]
฀ ฀Desired functions can be preset by your dealer. (p. 6)
o FUNCTION DISPLAY (p. 5)
฀ ฀Displays a variety of information such as an operating
channel number/name, Set mode contents, DTMF code,
selected functions and so on.
10
11
12
13
14
15
16
e DEALER-PROGRAMMABLE KEY [EMR]
฀ ฀Desired functions can be preset by your dealer.
(p. 6)
2
PANEL DESCRIPTION
!0 MULTI-CONNECTOR
฀ ฀Connects to optional equipment.
■ Function display
q w e r ty u i
Connector cover
NOTE: Attach the connector cover when optional
equipment is not used.
See page 3 for details.
CALA TXCU TXC SET
!0
q SIGNAL STRENGTH ICON
฀ Indicates relative signal strength level.
w LOW POWER ICON
฀ Appears when low output power is selected.
!1 BUSY/TRANSMIT INDICATOR
฀ ➥
฀ ฀฀Lights green while receiving a signal, or when the
squelch is open.
฀ ➥
฀ ฀Lights red while transmitting.
!2 VOLUME CONTROL [VOL]
฀ ฀Rotate to turn the transceiver power ON or OFF, and adjust the audio level.
฀
•฀฀When฀ the฀ battery฀ power฀ decreases฀ to฀ a฀ speciied฀ level,฀ low฀
power is automatically selected.
e AUDIBLE ICON
฀ ➥ Appears when the channel is in the ‘audible’ (unmute)
mode.
฀ ➥ Appears when a matched signal is received.
r COMPANDER ICON
฀ Appears when the compander function is activated.
t SCRAMBLER ICON
฀ Appears when the voice scrambler function is activated.
PANEL DESCRIPTION
■ Programmable function keys
y BELL ICON
฀ ฀Appears or blinks when a matched signal is received, depending on the presetting.
u CALL CODE MEMORY ICON
฀ ฀Appears when the call code memory is selected.
i BATTERY ICON
฀ ฀Appears or blinks when the battery power decreases to a
specified level.
Indication
Battery level
Full
Mid
Charging
required
Exhausted
Battery
blinks when the battery is over charged.
blinks when the battery is exhausted.
o ALPHANUMERIC DISPLAY
฀ ➥ Displays the operating channel number, channel name,
Set mode contents, DTMF code, and so on.
➥ The display mode can be set to one line or two lines.
Ask your dealer for details.
฀
•฀฀In฀this฀instruction฀manual,฀the฀LCD฀illustration฀is฀described฀
using the two-line display mode.
The following functions can be assigned to the [EMR],
[Side1], [Side2], [Side3], [P0], [P1], [P2] and [P3] programmable function keys.
Consult your Icom dealer or system operator for details concerning your transceivers programming.
If the programmable function names are bracketed in the following explanations, the specific key is used to activate the
function according to the presetting.
CH UP AND DOWN KEYS “UP” “DOWN”
➥฀฀Push฀to฀select฀an฀operating฀channel.฀When฀[Rotary฀selector] selects “operating channel,” this key is disabled.
➥ Push to select a transmit code channel after pushing [TX
Code CH Select].
➥ Push to select a DTMF channel after pushing [DTMF Autodial].
➥ Push to select a scan group after holding down [Scan].
➥ Push to select the desired application type, individual/talkgroup ID, TX status message and SDM (Short Data Message) after pushing [Digital Button].
10
11
12
13
14
15
16
!0 KEY ICONS
฀ Indicates the programmed function of the front panel keys
([P0], [P1], [P2] and [P3]).
2
PANEL DESCRIPTION
ZONE KEY “ZONE”
Push this key, then push [CH Up] or [CH Down] to select the
desired฀zone.฀When฀[Rotary฀selector]฀selects฀the฀“operating฀
zone,” this key operation is disabled.
What is a “zone”?— Selected channels are assigned to a
zone according to how they are to be used in a group. For
example, ‘Staff A’ and ‘Staff B’ are assigned to a “Business” zone, and ‘John’ and ‘Cindy’ are assigned to a “Private” zone.
ZONE UP AND DOWN KEYS “ZNUP” “ZNDN”
Push฀to฀select฀an฀operating฀zone.฀When฀[Rotary฀selector]฀selects an “operating zone,” these keys are disabled.
SCAN KEY “SCAN”
➥ Push to start or cancel a scan.
฀
•฀฀When฀the฀Power฀ON฀Scan฀function฀is฀activated,฀push฀to฀pause฀
the scan. The paused scan resumes after the specified time period has passed.
➥ Hold down this key for 1 second to display the scan group,
then push [CH Up] or [CH Down] to select the desired
group.
SCAN ADD/DEL (TAG) KEY “SCAD”
➥ Push to add a channel to, or delete it from the current scan
group.
1. Push to display the scan group, then push [CH Up] or
[CH Down] to select the desired group.
2. Push to add a channel to, or delete it from the selected
group.
3. Hold down for 1 second to exit the scan group selection
mode.
➥฀฀While฀a฀scan฀is฀paused฀on฀a฀non-priority฀channel,฀push฀
this key to delete the selected channel from the scan
group.
Depending on the presetting, the cleared channel may
be added to the scan group again after the scan is cancelled. (Nuisance Delete function)
PRIORITY CHANNEL KEYS “PRA” “PRB”
➥ Push to select the Priority A or Priority B channel.
PRIORITY CHANNEL (REWRITE) KEYS “PRAR” “PRBR”
➥ Push to select the Priority A or Priority B channel.
➥ Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] for
1 second to rewrite the Priority A or Priority B channel as
the operating channel.
PANEL DESCRIPTION
MEMORY CH 1/2/3/4 KEYS “CH1” “CH2” “CH3” “CH4”
Push to directly select memory channels 1 to 4.
MONI KEY “MON”
➥ Push to mute and release the CTCSS (DTCS) or 2-tone
squelch mute. Open any squelch or deactivate any mute
while holding down this key. (LMR operation only)
➥ Independently activates one or two of the following functions on each channel. (PMR operation only)
฀
฀
฀
•฀฀Hold฀ down฀ to฀ unmute฀ the฀ channel฀ (audio฀ is฀ heard;฀‘Audible’฀
mode).
•฀Push฀to฀mute฀the฀channel฀(sets฀to฀‘Inaudible’฀only).
•฀฀Push฀after฀the฀communication฀is฀inished฀to฀send฀a฀‘reset฀code’.฀
(5-tone/BIIS operation only)
NOTE: The unmute mode (‘Audible’ mode) may automatically return to the mute mode (‘Inaudible‘ mode)
after a specified period.
LIGHT KEY “LIGT”
Push to temporarily turn ON the transceiver’s backlight, only
when the backlight function is turned OFF in the User set mode.
LOCK KEY “LOCK”
➥ Hold down for 1 second to electronically lock all programmable keys to prevent accidental frequency changes and
unnecessary function access, except the following:
[PTT], [Call] (incl. Call A and Call B), [Moni(Audi)],
[Light],฀ [Emergency],฀ [Surveillance],฀ [Lone฀Worker]฀ and฀
[OPT 1/2/3].
➥ Hold down for 1 second again to turn the lock function OFF.
LONE WORKER KEY “LONE”
Push฀to฀turn฀the฀Lone฀Worker฀function฀ON฀or฀OFF.
•฀฀If฀the฀Lone฀Worker฀function฀is฀activated,฀the฀Emergency฀function฀is฀
automatically turned ON after the specified time period has passed
with no operation performed.
HIGH/LOW KEY “H/L”
Push to select the transmit output power temporarily or permanently, depending on the presetting.
•฀฀Ask฀your฀dealer฀for฀the฀output฀power฀level฀for฀each฀selection.
TONE/RAN CH SELECT KEY “T SEL”
➥฀฀While฀in฀the฀analog฀mode,฀push฀to฀enter฀the฀continuous฀
tone channel selection mode. Then select the desired tone
frequency/code setting using [CH Up] or [CH Down]. After
the selection, push this key again to set the tone/code.
➥฀฀While฀in฀the฀digital฀mode,฀push฀to฀enter฀the฀RAN฀channel฀
selection mode. Then select the desired RAN setting using
[CH Up] or [CH Down]. After the selection, push this key
again to set the RAN.
➥฀฀While฀in฀the฀mixed฀(digital฀and฀analog)฀mode,฀push฀to฀enter฀
the continuous tone channel selection mode. Then select
the desired tone frequency/code setting using [CH Up] or
[CH Down]. After the selection, push this key to set the
tone/code. After that, the RAN channel selection screen
appears. Select the desired RAN setting using [CH Up] or
[CH Down]. After the selection, push this key again to set
the RAN.
10
11
12
13
14
15
16
2
PANEL DESCRIPTION
C.TONE CH ENT KEY “TSEL”
Push to enter the continuous tone channel selection mode.
Then select the desired tone frequency/code setting using
[CH Up]/[CH Down]. The selected channel remains set as a
continuous tone channel until another channel is designated
as such.
TALK AROUND KEY “TA”
Push to turn the talk around function ON or OFF.
•฀฀The฀talk฀around฀function฀equalizes฀the฀transmit฀frequency฀to฀the฀
receive frequency for transceiver-to-transceiver communication.
WIDE/NARROW KEY “W/N”
Push to toggle the IF bandwidth between wide and narrow.
DTMF AUTODIAL KEY “DTMA”
Push to enter the DTMF channel selection mode. Then select
the desired DTMF channel using [CH Up]/[CH Down]. After
selecting the DTMF channel, push again to transmit the
selected DTMF code.
RE-DIAL KEY “DTMR”
Push to transmit the last-transmitted DTMF code.
CALL KEYS “CALL” “CALA” “CALB”
Push to transmit a 2/5-tone or BIIS ID code.
•฀฀A฀Call฀transmission฀may฀be฀necessary฀before฀you฀call฀another฀station, depending on your signaling system.
•฀฀[Call฀ A]฀ and/or฀ [Call฀ B]฀ may฀ be฀ selectable฀ when฀ your฀ system฀
employs selective ‘Individual/Group’ calls. Ask your dealer which
call is assigned to each key.
EMERGENCY KEY “EMR”
Hold down to transmit an emergency call.
•฀฀The฀emergency฀call฀transmits฀and฀beep฀sounds.฀The฀display฀does฀
not change.
•฀฀The฀transceiver฀can฀transmit฀the฀emergency฀call฀silently,฀or฀with฀the฀
display changing, depending on the presetting. Ask your dealer for
details.
•฀฀If฀you฀want฀to฀cancel฀the฀emergency฀call,฀hold฀down฀the฀key฀again฀
before transmitting it.
•฀฀The฀emergency฀call฀is฀transmitted฀only฀one฀time,฀or฀repeatedly฀until฀
receiving a control code, depending on the presetting.
SURVEILLANCE KEY “SURV”
Push to turn the surveillance function ON or OFF.
When฀this฀function฀is฀turned฀ON,฀a฀beep฀is฀not฀heard฀and฀the฀
LCD backlight does not light when a signal is received or a
key is pushed.
TX CODE ENTER KEYS “TXCE”
Push to directly enter the ID code edit mode, for both 5-tone
and MSK. Then set the desired digit using [CH Up]/[CH
Down]. (p. 15)
PANEL DESCRIPTION
TX CODE CHANNEL SELECT KEY “TXC”
Push to enter the TX code channel selection mode. Then set
the desired channel using [CH Up]/[CH Down]. (pp. 14, 15)
USER SET MODE KEY “SET”
➥ Hold down for 1 second to enter the User set mode.
TX CODE CHANNEL UP/DOWN KEYS “TXCU” “TXCD”
Push to select a TX code channel directly.
➥ Hold down this key for 1 second again to exit the User set
mode.
ID-MEMORY SELECT KEY “IDMS”
➥ Recalls detected ID codes.
฀
฀
•฀฀Push฀ this฀ key,฀ then฀ select฀ the฀ ID฀ code฀ using฀ [CH฀ Up]/[CH฀
Down].
•฀Up฀to฀ive฀ID’s฀can฀be฀memorized.
➥ Hold down for 1 second to erase the selected ID’s.
SCRAMBLER/ENCRYPTION KEY “SCR”
➥฀฀While฀in฀the฀analog฀mode฀operation,฀push฀to฀toggle฀the฀
voice scrambler function ON or OFF.
➥฀฀While฀ in฀ the฀ digital฀ mode฀ operation,฀ push฀ to฀ toggle฀ the฀
encryption transmission function ON or OFF.
COMPANDER KEY “COMP”
Push to toggle the compander function ON or OFF.
The compander function reduces noise components from the
transmitting audio to provide clear communication.
฀
•฀฀While฀in฀the฀User฀set฀mode,฀push฀this฀key฀to฀select฀an฀item,฀and฀
change the value or condition using [CH Up]/[CH Down].
The User set mode can also be entered through the ‘Power
ON function.’ Refer to page 16.
OPT OUT KEYS “OP1” “OP2” “OP3”
Push to control the output signal level from the optional unit
connector.
OPT MOMENTARY KEYS “O1M” “O2M” “O3M”
Push to control the output signal level from the optional unit
connector.
10
11
12
13
14
15
16
10
3
BASIC OPERATION
■ Turning power ON
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
(p. 21)
q Rotate [VOL] to turn ON the power.
w If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
฀
฀
฀
•฀฀The฀10-keypad฀can฀be฀used฀for฀password฀input,฀depending฀on฀
the transceiver version.
•฀฀The฀keys฀in฀the฀table฀below฀can฀be฀used฀for฀password฀input.
•฀฀The฀transceiver฀detects฀numbers฀in฀the฀same฀block฀as฀identical.฀฀
Therefore “01234” and “56789” are the same.
KEY
NUMBER
P0
P1
P2
P3
(Side1)
e฀฀If฀the฀“PASSWORD”฀indication฀does฀not฀clear฀after฀inputting 6 digits, the input code number may be incorrect. Turn
OFF the power and start over.
11
D Battery type selection
When฀turning฀ON฀the฀transceiver,฀the฀battery฀type฀must฀be฀
selected according to the attached battery type.
q Turn OFF the power.
w ฀While฀holding฀down฀[EMR]฀and฀[PTT],฀turn฀ON฀the฀power฀
with rotating [VOL] to toggle the attaching battery type.
฀
฀
฀
•฀฀After฀the฀display฀appears,฀release฀[EMR]฀and฀[PTT].
•฀“฀DRY฀BATT”฀is฀displayed฀for฀about฀3฀seconds,฀then฀the฀low฀power฀
icon “Lo” appears when the battery case is selected. The transmit output power is automatically set to low1.
•฀฀“LI-ION”฀is฀displayed฀for฀about฀3฀seconds฀when฀the฀Lithium-ion฀
battery pack is selected.
•฀฀This฀operation฀may฀not฀be฀available,฀depending฀on฀the฀presetting.฀
Ask your dealer for details.
BASIC OPERATION
■ Channel selection
Several types of channel selections are available. Methods
may differ, depending on the presetting.
NON-ZONE TYPE:
To select the desired operating channel:
•฀Push฀[CH฀Up]฀or฀[CH฀Down].
•฀Rotate฀[ROTARY฀SELECTOR]*.
AUTOMATIC SCAN TYPE:
Channel฀setting฀is฀not฀necessary฀for฀this฀type.฀When฀you฀turn฀
ON power, the transceiver automatically starts scanning.
Scanning stops when a call is received.
- Up to 16 preprogrammed channels can be selected.
•฀Push฀one฀of฀[MR-CH฀1]฀to฀[MR-CH฀4].฀
ZONE TYPE:
To select the desired zone:
•฀Push฀[Zone],฀then฀push฀[CH฀Up]฀or฀[CH฀Down].
•฀Push฀[Zone฀Up]฀or฀[Zone฀Down].
•฀Rotate฀[ROTARY฀SELECTOR]*.
- Up to 16 preprogrammed zones can be selected.
D Voting operation
The transceiver automatically starts scanning when a zone,
specified for the voting operation, is selected.
The voting scan detects the signal of the repeater and automatically selects the strongest station.
*฀Depending฀on฀the฀presetting.
฀ ฀When฀[Rotary฀selector]฀selects฀“Operating฀channel,”฀[CH฀Up]/[CH฀
Down] are disabled.
฀ ฀When฀[Rotary฀selector]฀selects฀“Operating฀zone,”฀[Zone]/[Zone฀Up]/฀
[Zone฀Down]฀are฀disabled.
10
11
12
13
14
15
16
12
3
BASIC OPERATION
■ Call procedure
■ Receiving and transmitting
When฀your฀system฀employs฀tone฀signaling,฀excluding฀CTCSS฀
and DTCS, this call procedure may be necessary prior to
voice transmission. The tone signaling employed may be a
selective calling system which allows you to call only specific
station(s) and prevents unwanted stations from contacting
you.
q Select the desired TX code channel or 2/5-tone code according to your System operator’s instructions.
฀
฀
•฀This฀may฀not฀be฀necessary,฀depending฀on฀the฀presetting.
•฀Refer฀to฀pages฀14฀or฀15฀for฀selection.
w Push [Call], assigned to one of the dealer programmable
keys.
e After transmitting, the remainder of your communication
can be carried out in the normal way.
Selective calling
Non-selective calling
CAUTION: Transmitting without an antenna will damage
the transceiver.
Receiving:
q Rotate [VOL] to turn ON the power.
w Push [CH Up] or [CH Down], or rotate [ROTARY SELECTOR], depending on the presetting, to sequentially select
the conventional system channel.
e฀฀When฀receiving฀a฀call,฀adjust฀the฀audio฀output฀level฀to฀a฀
comfortable listening level.
NOTE:฀When฀a฀matched฀RX฀code฀signal฀is฀received,฀audio฀
from the microphone may be automatically transmitted for
a฀speciied฀time฀period.*
*฀Depending฀on฀the฀presetting.฀Ask฀your฀dealer฀for฀details.
Transmitting:
Wait฀for฀the฀channel฀to฀become฀clear฀to฀avoid฀interference.
q฀฀While฀holding฀down฀[PTT],฀speak฀into฀the฀microphone฀at฀a฀
normal voice level.
฀
•฀฀When฀a฀tone฀signaling฀system฀is฀used,฀the฀call฀procedure฀described on the previous page may be necessary.
w Release [PTT] to receive.
IMPORTANT: To maximize the audio quality of your signal:
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then speak at a normal voice level.
13
BASIC OPERATION
D Transmitting notes
•฀Transmit฀inhibit฀function
The transceiver has several inhibit functions which restrict
transmission under the following conditions:
-฀฀฀The฀channel฀is฀muted฀(‘Inaudible’฀mode;฀“ ” (Audible icon)
does not appear.)
- The channel is busy.
- Unmatched or matched CTCSS is received, depending on
the presetting.
- The selected channel is a ‘receive only’ channel.
•฀Time-out฀timer
After continuous transmission for a preset time period, the
time-out timer causes the transceiver to stop transmitting.
•฀Penalty฀timer
Once transmission is cut OFF, it is further inhibited for a
period determined by the Penalty timer.
D TX code channel selection
If the transceiver has [TX Code CH Select] assigned to it,
the display can be toggled between the operating channel
number or name, and the TX code channel number or name.
When฀the฀TX฀code฀channel฀number,฀or฀name฀is฀displayed,฀
pushing [CH Up] or [CH Down] selects the TX code channel.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select]— a TX code channel number
or name appears.
w Push [CH Up] or [CH Down] to select the desired TX code
channel.
e After selecting, push [TX Code CH Select] to set the
code.
฀
•฀Return฀to฀the฀standby฀mode.
r Push [Call] to transmit the selected TX code.
USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY:
If the transceiver has a [TX Code CH Up] or [TX Code CH
Down] key assigned, the preset TX code channel can be directly selected when pushed.
10
11
12
13
14
15
16
☞ Continued on the next page
14
3
BASIC OPERATION
D TX code number edit (PMR operation only)
If the transceiver has [TX Code CH Select] or [TX Code
Enter] assigned, the TX code contents can be edited within
the allowable digits.
USING [TX CODE CH SELECT] KEY:
q Push [TX Code CH Select] to enter the TX code channel
selection mode.
฀
•฀฀Select฀ the฀ desired฀ operating฀ channel฀ before฀ entering฀ the฀TX฀
code channel selection mode, if necessary.
w Push [TX Code CH Select] for 1 second to enter the TX
code edit mode.
฀
•฀The฀digit฀to฀be฀edited฀blinks.
e Push [TX Code CH Select] to select the desired digit to be
edited.
r Push [CH Up]/[CH Down] to select the desired digit.
t Push [TX Code CH Select] to set it. The digit to the right
will automatically blink.
y Repeat r and t to edit all allowable digits.
u After editing, push [TX Code CH Select] to set the code.
฀
฀
•฀The฀digit฀to฀be฀edited฀blinks.
e Push [TX Code Enter] to select the desired digit to be edited.
r Push [CH Up]/[CH Down] to select the desired digit.
t Push [TX Code Enter] to set. The digit to the right will automatically blink.
y Repeat r and t to edit all allowable digits.
u After editing, push [TX Code Enter] to set.
฀
•฀Return฀to฀the฀standby฀mode.
i Push [Call] to transmit.
D DTMF transmission
If the transceiver has [DTMF Autodial] assigned, the automatic DTMF transmission function can be used. Up to 8
DTMF channels are selectable.
•฀Return฀to฀the฀standby฀mode.
i Push [Call] to transmit.
15
USING [TX CODE ENTER] KEY:
q After pushing [TX Code CH Select], push [CH Up] or [CH
Down], or push [TX Code CH Up] or [TX Code CH Down]
to select the desired TX code channel.
w Push [TX Code Enter] to enter the TX code edit mode.
q Push [DTMF Autodial]— a DTMF channel appears.
w Push [CH Up] or [CH Down] to select the desired DTMF
channel.
e Push [DTMF Autodial] to transmit the DTMF code on the
selected DTMF channel.
BASIC OPERATION
■ User set mode
■ Scrambler function
The User set mode is accessed at power ON, and allows you
to set seldom-changed settings and “customize” the transceiver operation to suit your preferences and operating style.
The voice scrambler function provides private communication between stations. All transceiver versions have a built-in
frequency inversion type scrambler.
Entering the User set mode:
q฀฀While฀holding฀down฀[P1]฀and฀[P2],฀rotate฀[VOL]฀to฀turn฀ON฀
the power.
➥ Push [Scrambler] to toggle the scrambler function ON or
OFF.
฀
•฀“SET฀MODE”฀appears฀for฀1฀second฀at฀power฀ON.
w Hold down [P0] to enter the User set mode.
e Push [P0] several times to select the appropriate item.
Then push [Side2] or [Side3] to set the desired level or option.
฀
฀
•฀฀Available฀ set฀ mode฀ functions฀ are฀ Backlight, LCD contrast,
Beep, Beep Level, Ringer Level, SQL Level, AF Min Level,
Mic Gain, VOX Gain*,฀VOX Delay*,฀Battery Voltage, Signal
Moni, Lone Worker and System Info.
฀฀*฀Appears฀only฀when฀the฀external฀VOX฀unit฀is฀connected.
r Hold down [P0] again to exit the User set mode.
The User set mode is also selectable with a programmable
key. Please refer to page 10 [User Set Mode] section for instructions on using the key assigned to the User set mode.
[User Set Mode] allows for quick item selection. Set “Enable”
for the often used items in the CS-F3160/F5060 CLONING
SOFTWARE. Ask your dealer for details.
฀
•฀“฀ ” (Scrambler icon) appears when the function is ON.
■ Stun function
When฀the฀speciied฀ID,฀set฀as฀a฀stun฀ID฀or฀kill฀ID,฀is฀received,฀
the stun function is activated.
When฀a฀stun฀ID฀is฀received,฀the฀transceiver฀becomes฀unusable. Entering the password (p. 11) or receiving a revive ID, is
necessary to operate the transceiver again.
When฀ a฀ kill฀ ID฀ is฀ received,฀ the฀ transceiver฀ switches฀ to฀ the฀
cloning required condition. Cloning the transceiver is necessary to operate the transceiver again.
10
11
12
13
14
15
16
NOTE: [Side2] or [Side3] and [P0] activate while in the
User set mode, regardless of the assigned key functions.
16
3
BASIC OPERATION
■ Emergency transmission
When฀[Emergency]฀is฀pushed฀for฀the฀speciied฀time฀period,฀an฀
emergency signal is transmitted once, or repeatedly, on the
specified emergency channel, depending on the presetting.
A repeat emergency signal is automatically transmitted until
the transceiver receives an acknowledgement signal, or you
turn OFF the transceiver power.
When฀no฀emergency฀channel฀is฀speciied,฀the฀signal฀is฀transmitted on the previously selected channel.
If you want to cancel the emergency call, hold down [Emergency] again before transmitting it.
If your transceiver is preset for Silent operation, you can
transmit an Emergency call without the beep sounding and
the LED indicator lighting.
IMPORTANT: It is recommended to set a separate emergency channel to provide reliable emergency calls.
D NOTES
Depending on the presetting, the following functions may be
automatically activated. Ask your dealer for details.
•฀Auto฀TX฀function
After the emergency call transmission, audio from the microphone is automatically transmitted for a specified time period.
•฀Auto฀RX฀function
After the emergency call transmission, the transceiver stands
by in the audible mode for the specified time period.
■ Man Down Emergency Call
This function is available, depending on the transceiver version.
When฀the฀transceiver฀has฀been฀left฀in฀a฀horizontal฀position฀for฀
the฀ speciied฀ time฀ period*,฀ the฀ transceiver฀ enters฀ the฀ emergency mode, and then the countdown starts.
After฀ the฀ speciied฀ time฀ period*฀ has฀ passed,฀ an฀ emergency฀
call is automatically transmitted once, or repeatedly.
If the transceiver is placed in a vertical position before the first
transmission, the transceiver exits the emergency mode and
the emergency call is cancelled.
IMPORTANT: It is recommended to set a separate emergency channel to provide reliable emergency calls.
17
BASIC OPERATION
■ Automatic Key Lock function
When฀[Lock]฀is฀assigned฀to฀any฀key,฀and฀the฀Automatic฀Key฀
Lock฀timer฀is฀preprogrammed*,฀the฀key฀lock฀function฀can฀be฀
automatically turned ON after the specified time period has
passed with no key operation.
While฀the฀lock฀function฀is฀ON,฀hold฀down฀[Lock]฀for฀1฀second฀
to turn the function OFF.
*When฀“0”฀is฀programmed,฀this฀function฀is฀disabled.
■ Priority A channel selection
When฀one฀of฀the฀following฀operations฀is฀performed,฀the฀transceiver automatically selects the Priority A channel.
•฀Turning฀the฀power฀ON
The Priority A channel is selected each time the transceiver power is turned ON.
•฀Status฀call
The Priority A channel is selected when transmitting a
status call. (BIIS operation only)
•฀Clear฀down
The Priority A channel is selected after the clear down
signal is transmitted.
10
11
12
13
14
15
16
18
4
BATTERY CHARGING
■ Caution
Misuse of Lithium-ion batteries may result in the following
hazards: smoke, fire, or the battery may rupture. Misuse
can also cause damage to the battery or degradation of
battery performance.
•฀฀R DANGER! short the terminals (or charging terminals) of
the battery pack. Also, current may flow into nearby metal
objects such as a key, so be careful when placing battery
packs (or the transceiver) in bags, etc.
Simply carrying with or placing near metal objects such as
a necklace, etc. may cause shorting. This may damage not
only the battery pack, but also the transceiver.
•฀฀R DANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom charger. Only Icom battery
packs are tested and approved for use and charge with
Icom radios or Icom charger. Using third-party or counterfeit
battery packs or charger may cause smoke, fire, or cause
the battery to burst.
D Battery caution
•฀฀R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted
or dropped, or if the battery has been subjected to heavy
pressure. Battery damage may not be visible on the outside
of the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery may
rupture or catch fire.
19
•฀฀R DANGER! NEVER use or leave battery packs in areas
with temperatures above +60˚C (+140˚F). High temperature buildup in the battery, such as could occur near fires
or stoves, inside a sun heated car, or in direct sunlight may
cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery performance or shorten
battery life.
•฀฀R DANGER! DO NOT expose the battery to rain, snow,
seawater, or any other liquids. Never charge or use a wet
battery. If the battery gets wet, be sure to wipe it dry before
using. The battery is not waterproof.
•฀฀R DANGER! NEVER incinerate used battery packs since
internal battery gas may cause them to rupture, or may
cause an explosion.
•฀฀R DANGER! NEVER solder the battery terminals or
NEVER modify the battery pack. This may cause heat generation, and the battery may rupture, emit smoke or catch
fire.
•฀฀R DANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any other
equipment, or for any purpose that is not specified in this
instruction manual.
•฀฀R DANGER! If fluid from inside the battery gets in your
eyes, blindness can result. Rinse your eyes with clean water,
without rubbing them, and see a doctor immediately.
BATTERY CHARGING
•฀฀R WARNING! Immediately stop using the battery if it emits
an abnormal odor, heats up, or is discolored or deformed. If
any of these conditions occur, contact your Icom dealer or
distributor.
•฀฀R WARNING! Immediately wash, using clean water, any
part of the body that comes into contact with fluid from inside the battery.
•฀฀R WARNING! NEVER put the battery in a microwave oven,
high-pressure container, or in an induction heating cooker.
This could cause a fire, overheating, or cause the battery
to rupture.
•฀฀CAUTION: Always use the battery within the specified temperature range, –20˚C to +60˚C (–4˚F to +140˚F). Using the
battery out of its specified temperature range will reduce the
battery’s performance and battery life.
•฀฀CAUTION: Shorter battery life could occur if the battery is
left fully charged, completely discharged, or in an excessive฀temperature฀environment฀(above฀+50˚C;฀+122˚F)฀for฀an฀
extended period of time. If the battery must be left unused
for a long time, it must be detached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place
with the temperature range as below:
–20˚C to +50˚C (–4˚F to +122˚F) (within a month)
–20˚C to +35˚C (–4˚F to +95˚F) (within three months)
D Charging caution
•฀฀R DANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near fires or stoves,
inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will
activate, causing the battery to stop charging.
•฀฀R WARNING! NEVER charge or leave the battery in the
battery charger beyond the specified time for charging. If
the battery is not completely charged by the specified time,
stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the specified
time limit may cause a fire, overheating, or the battery may
rupture.
•฀฀R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or
soiled. This could corrode the battery charger terminals or
damage the charger. The charger is not waterproof.
•฀฀CAUTION: NEVER charge the battery outside of the speciied฀temperature฀range:฀BC-160฀and฀BC-171฀(0˚C฀to฀+45˚C;฀
+32˚F฀to฀+113˚F),฀BC-119฀and฀BC-121฀(+10˚C฀to฀+40˚C;฀
+50˚F to +104˚F). Icom recommends charging the battery
at +20˚C (+68˚F). The battery may heat up or rupture if
charged out of the specified temperature range. Additionally,
battery performance or battery life may be reduced.
10
11
12
13
14
15
16
20
4
BATTERY CHARGING
■ Optional battery chargers
D Rapid charging with the BC-160
D Regular charging with the BC-171
The optional BC-160 provides rapid charging of the Li-ion
battery pack.
Charging฀time:฀Approximately฀3฀hours฀with฀the฀BP-232WP
The optional BC-171 provides regular charging of the Li-ion
battery pack.
Charging฀time:฀Approximately฀10฀hours฀with฀the฀BP-232WP
The following items are additionally required:
•฀฀An฀AC฀adapter฀(may฀be฀supplied฀with฀BC-160,฀depending฀
on version) or the OPC-515L/CP-23L DC power cable.
The following items are additionally required:
•฀฀An฀AC฀adapter฀(may฀be฀supplied฀with฀BC-171,฀depending฀
on version) or the OPC-515L/CP-23L DC power cable.
AC adapter
Transceiver
(A different type, or no AC adapter is
supplied, depending on the version.)
Turn OFF
Battery the power
pack
Optional OPC-515L* (for
13.8 V power source) or
CP-23L (for 12 V cigarette
lighter socket) can be used
instead of the AC adapter.
21
* CAUTION: NEVER
connect the OPC515L to a power
source using reverse
polarity. This will ruin
the battery charger.
White line:
Black line :
AC adapter
(A different type, or no AC adapter is
supplied, depending on the version.)
Optional OPC-515L* (for
13.8 V power source) or
CP-23L (for 12 V cigarette
lighter socket) can be used
instead of the AC adapter.
* CAUTION: NEVER
connect the OPC515L to a power
source using reverse
polarity. This will ruin
the battery charger.
White line:
Black line :
Transceiver
Turn OFF
Battery the power
pack
BATTERY CHARGING
D AD-106 installation
D Rapid charging with the BC-119N+AD-106
The AD-106 CHARGER ADAPTER must be installed into the BC119N or BC-121N before battery charging.
The optional BC-119N provides rapidly charges the Li-ion
battery pack.
Charging฀time:฀Approximately฀3฀hours฀with฀the฀BP-232WP
q Connect the AD-106 CHARGER ADAPTER and the BC-119N/
BC-121N.
w Install the AD-106 into the holder space of the BC-119N/
BC-121N with the supplied screws.
The following items are additionally required.
•฀AD-106฀CHARGER ADAPTER (purchase separately)
•฀฀An฀AC฀adapter฀(may฀be฀supplied฀with฀BC-119N,฀depending฀
on version) or the OPC-515L/CP-23L DC power cable.
AD-106
AC adapter
(A different type, or no AC
adapter is supplied, depending on the version.)
Plugs
Battery
pack
Transceiver
AD-106 charger
adapter is installed
in the BC-119N.
Screws supplied
with the charger
adapter
Sockets
This illustration shows
the BC-119N.
Turn OFF
the power
Optional OPC-515L* (for
13.8 V power source) or
CP-23L (for 12 V cigarette
lighter socket) can be used
instead of the AC adapter.
10
11
12
13
14
15
16
* CAUTION: NEVER connect the OPC515L to a power source using reverse
polarity. This will ruin the battery charger.
White line:
Black line :
22
4
BATTERY CHARGING
D Rapid charging with the BC-121N+AD-106
The optional BC-121N allows up to 6 battery packs to be simultaneously charged.
Charging฀time:฀Approximately฀3฀hours฀with฀the฀BP-232WP
IMPORTANT: Battery charging caution
Ensure the guide tabs on the battery pack are correctly
aligned with the guide rails inside the charger adapter. This
illustration is for the BC-160.
The following items are additionally required.
•฀Six฀AD-106฀CHARGER ADAPTERS (purchase separately)
•฀฀An฀AC฀adapter฀or฀the฀OPC-656฀DC฀power฀cable
Turn OFF the power
Battery
pack
AC adapter
(Purchase
separately)
Transceiver
AD-106 charger
adapters are installed
in each slot.
Tabs
Guide rail
OPC-656* DC power cable
(Connect with a DC power supply;
13.8 V/at least 7 A)
*Polarity of the OPC-656
Red line :
Black line :
23
5
BATTERY CASE
■ Optional battery case (BP-240)
When฀using฀the฀optional฀battery฀case,฀install฀six฀AAA฀(LR03)฀
size alkaline batteries, as illustrated to the right.
Fig.1
BP-240
q Unhook the battery cover release hook (q), and open the
cover in the direction of the arrow (w). (Fig.1)
w Install six AAA (LR03) size alkaline batteries. (Fig.2)
฀
฀
•฀Install฀only฀alkaline฀batteries.
•฀Be฀sure฀to฀observe฀the฀correct฀polarity.
e Replace the cover in the direction of the arrow (e), then
close (r). Push the battery cover release hook until it
makes a ‘click’ sound (t). (Fig.3)
CAUTION:
฀•฀฀When฀installing฀the฀batteries,฀make฀sure฀they฀are฀all฀the฀
same brand, type and capacity. Also, do not mix new and
old batteries together.
฀•฀฀Keep฀battery฀terminals฀clean.฀It’s฀a฀good฀idea฀to฀regularly฀
clean them.
฀•฀฀Never฀incinerate฀used฀battery฀cells฀since฀internal฀battery฀
gas may cause them to rupture.
฀•฀฀Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it.
NOTE: When฀the฀optional฀battery฀case฀is฀attached,฀the฀
battery type must be set to “DRY BATT” when turning ON
the transceiver. (p. 11)
Fig.2
Fig.3
10
11
12
13
14
15
16
24
6
SWIVEL BELT CLIP
■ MB-93 contents
Qty.
q Belt clip ............................................................................1
w Base clip ..........................................................................1
r Clip the belt clip to a place on your belt. Insert the transceiver into the belt clip until the base clip is fully inserted
into the groove.
■ To attach
t Once the transceiver is locked in place, it swivels, as illustrated below.
q Release the battery pack if it is attached. (p. 2)
w Slide the base clip in the direction of the arrow until it locks
and makes a ‘click’ sound.
Once the transceiver is locked in place,
it will swivel 360 degrees.
e Attach the battery pack. (p. 2)
25
SWIVEL฀BELT฀CLIP
■ To detach
q Turn the transceiver upside down in the direction of the
arrow and pull it out of the belt clip.
w Release the battery pack if it is attached. (p. 2)
e Pinch the clip (q), and slide the base clip in the direction
of the arrow (w).
CAUTION:
HOLD THE TRANSCEIVER TIGHTLY WHEN HANGING
OR DETACHING THE TRANSCEIVER FROM THE BELT
CLIP.
Otherwise the transceiver may not properly attach to the
holder or swivel, if the transceiver has been accidentally
dropped and the base clip is scratched or damaged.
10
11
12
13
14
15
16
26
7
SPEAKER MICROPHONE
■ Optional HM-184
■ To attach
Microphone
Attach the connector of the speaker microphone into the multi
connector on the transceiver and tighten the screw.
Speaker
PTT SWITCH
Hold down to
transmit;
release to receive.
Belt clip
Turn OFF the transceiver power when attaching or detaching
the microphone.
NEVER immerse the connector in water. If the connector
becomes wet, be sure to dry it BEFORE attaching it to the
transceiver.
NOTE: The microphone element is located at the top of
the speaker microphone, as shown in the diagram above.
To maximize the readability of your transmitted signal
(voice), hold the microphone Approximately 5 to 10 cm (2
to 4 inches) from your mouth, and speak at a normal voice
level.
27
Screw
Coin
CAUTION: Firmly attach
to the multi connector, but
do not overtighten.
A loose connection will allow water intrusion into
the connector; an overtightened connection will
damage the connector
pins in the transceiver.
IMPORTANT: KEEP the connector cover attached to the
transceiver when the speaker microphone is not in use.
(p. 3)
Water฀will฀not฀get฀into฀the฀transceiver,฀even฀if฀the฀cover฀is฀
not attached. However, the terminals (pins) will become
rusty, or the transceiver will function abnormally if the connector becomes wet.
OPTIONS
D BATTERY PACKS
•฀฀BP-232WP฀LI-ION BATTERY PACK
Voltage: 7.4 V, Capacity: 2250 mAh (min.), 2300 mAh (typ.)
Battery life:
GPS unit
Digital mode
Analog mode
Built in type
10.5 hrs.
11 hrs.
non GPS type
12 hrs.
12.5 hrs.
When฀the฀power฀save฀function฀is฀turned฀ON,฀and฀the฀operating฀
periods฀are฀calculated฀under฀the฀following฀conditions;฀
TX : RX : standby = 5 : 5 : 90
•฀฀BP-240฀BATTERY CASE
Battery case for AAA (LR03) × 6 alkaline batteries
•฀฀BP-261฀BATTERY CASE
Battery case for AA (LR06) × 6 alkaline batteries
D CHARGERS
•฀฀BC-119N฀DESKTOP CHARGER + AD-106 CHARGER ADAPTER
+ BC-145S AC ADAPTER
For rapid charging of battery packs. An AC adapter may be
supplied with the charger, depending on the version.
Charging time: Approximately 3 hours.
•฀฀BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs.)
+ BC-157S AC ADAPTER
For rapid charging of up to 6 battery packs simultaneously.
Six AD-106s are required. An AC adapter should be purchased separately.
Charging time: Approximately 3 hours.
•฀฀BC-160฀DESKTOP CHARGER + BC-145S AC ADAPTER
For rapid charging of battery packs. An AC adapter may be
supplied with the charger, depending on the version.
Charging time: Approximately 3 hours.
•฀฀BC-171฀DESKTOP CHARGER + BC-147S AC ADAPTER
For regular charging of battery packs. An AC adapter may
be supplied with the charger, depending on the version.
Charging time: Approximately 10 hours.
D BELT CLIPS
•฀MB-93฀SWIVEL BELT CLIP
•฀MB-94R฀BELT CLIP
Exclusive alligator-type belt clip.
•฀MB-96N/96F฀LEATHER BELT HANGER
D DC CABLES
•฀CP-23L฀CIGARETTE LIGHTER CABLE
Allows charging of the battery pack through a 12 V cigarette
lighter socket. For use with the BC-119N/BC-160/BC-171
•฀OPC-515L/OPC-656฀DC POWER CABLES
Allows charging of the battery pack using a 13.8 V power
source instead of the AC adapter.
OPC-515L : For BC-119N
OPC-656 : For BC-121N
10
11
12
13
14
15
16
28
8
OPTIONS
D OTHER OPTIONS
D ANTENNAS
•฀AD-118฀ACC ADAPTER
Allows you to connect an accessory which uses a HIROSE
plug. See the instruction sheet of the AD-118 for details of
the recommended accessories.
CAUTION: The AD-118 does not have any waterproof
protection.฀When฀ it฀ is฀ connected,฀ NEVER฀ expose฀ the฀
adaptor and the transceiver to rain, snow or any liquids.
•฀FA-SC73US฀STUBBY ANTENNAS
Shorter UHF antennas.
Frequency range 450–490 MHz
•฀HM-184฀SPEAKER MICROPHONE
Rugged type speaker microphone.
•฀MB-130฀VEHICLE CHARGER BRACKET
Mounts the BC-160 DESKTOP CHARGER on to variety of place
in vehicle.
•฀฀FA-SC03U/FA-SC25U/FA-SC57U/FA-SC72U฀
FLEXIBLE ANTENNAS
UHF antennas.
FA-SC03U: Frequency range 380–430 MHz
FA-SC25U: Frequency range 400–430 MHz
FA-SC57U: Frequency range 430–470 MHz
FA-SC72U: Frequency range 470–520 MHz
•฀FA-SC61VC/FA-SC61UC฀CUT ANTENNAS
FA-SC61UC: 380–520 MHz
Approved Icom optional equipment is designed for optimal
performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an
Icom transceiver in the event the Icom transceiver is used with
equipment that is not manufactured or approved by Icom.
Some options may not be available in some countries. Please
ask your dealer for details.
29
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for
and classified as “Occupational Use Only,” meaning it
must be used only during the course of employment
by individuals aware of the hazards, and the ways to
W ARN ING
minimize such hazards. This radio is NOT intended for
use by the “General Population” in an uncontrolled environment.
This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only.” In addition, your Icom radio
complies with the following Standards and Guidelines with regard to
RF energy and electromagnetic energy levels and evaluation of such
levels for exposure to humans:
฀ •฀฀FCC฀OET฀Bulletin฀65฀Edition฀97-01฀Supplement฀C,฀Evaluating฀
Compliance with FCC Guidelines for Human Exposure to Radio
Frequency Electromagnetic Fields.
฀ •฀฀A merican฀ National฀ Standards฀ Institute฀ (C95.1-1992),฀ IEEE฀
Standard for Safety Levels with Respect to Human Exposure to
Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
฀ •฀฀American฀National฀Standards฀Institute฀(C95.3-1992),฀IEEE฀Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.
฀ •฀฀The฀following฀accessories฀are฀authorized฀for฀use฀with฀this฀product. Use of accessories other than those specified may result in
RF exposure levels exceeding the FCC requirements for wireless
RF฀exposure.;฀Belt฀Clip฀(MB-93,฀MB-94,฀MB-96N฀and฀MB-96F),฀
Rechargeable฀Li-ion฀Battery฀Pack฀(BP-232WP),฀Alkalies฀Battery฀
Case (BP-240 and BP-261) and Speaker microphone (HM-184).
To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for
occupational use, always adhere to the following
guidelines:
C AU TIO N
฀ •฀฀DO NOT operate the radio without a proper antenna attached, as
this may damaged the radio and may also cause you to exceed
FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically
authorized by the manufacturer for use with this radio.
฀ •฀฀DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”). Transmitting more than 50% of the time can cause
FCC RF exposure compliance requirements to be exceeded.
The radio is transmitting when the TX indicator lights red. You
can cause the radio to transmit by pressing the “PTT” switch.
฀ •฀฀ALWAYS keep the antenna at least 2.5 cm (1 inch) away from
the body when transmitting and only use the Icom belt-clips
listed on page 28 when attaching the radio to your belt, etc.,
to ensure FCC RF exposure compliance requirements are not
exceeded. To provide the recipients of your transmission the best
sound quality, hold the antenna at least 5 cm (2 inches) from
your mouth, and slightly off to one side.
The information listed above provides the user with the information
needed to make him or her aware of RF exposure, and what to do
to assure that this radio operates with the FCC RF exposure limits
of this radio.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid
such interference, turn OFF the radio in areas where signs are posted
to do so. DO NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and blasting sites.
Occupational/Controlled Use
The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons
are fully aware of the potential for exposure and can exercise control
over their exposure.
10
11
12
13
14
15
16
30
9
SAFETY TRAINING INFORMATION
Votre radio Icom produit une énergie électromagnétique
de radiofréquences (RF), en mode de transmission.
Cette radio est conçue pour un «usage professionnel
seulement» et classée comme tel, ce qui signifie qu’elle
doit être utilisée uniquement dans le cadre d'un travail
par des personnes conscientes des dangers et des mesures visant à minimiser ces dangers. Elle N’EST PAS conçue pour une «utilisation grand
public», dans un environnement non contrôlé.
Cet appareil a été évalué et jugé conforme, aux limites d’exposition aux
RF de la FCC, pour une «utilisation grand public». En outre, votre radio
Icom satisfait les normes et directives qui suivent en matière de niveaux
d'énergie et d’énergie électromagnétique de RF et d’évaluation de tels
niveaux en ce qui concerne l’exposition humaine:
฀ •฀฀Supplément฀ C,฀ édition฀ 97-01,฀ du฀ Bulletin฀ OET฀ n°฀ 65฀ de฀ la฀ FCC,฀
«Evaluating Compliance with FCC Guidelines for Human Exposure
to Radio Frequency Electromagnetic Fields».
฀
฀
฀
•฀฀Norme฀ de฀ l’American฀ National฀ Standards฀ Institute฀ (ANSI):฀ IEEE฀
C95.1-1992 sur les niveaux de sécurité compatibles avec l’exposition
humaine aux champs électromagnétiques de radiofréquences (3 kHz
à 300 GHz).
•฀฀Norme฀de฀l’ANSI:฀IEEE฀C95.3-1992฀sur฀la฀méthode฀d’évaluation฀recommandée du champ magnétique potentiellement dangereux des
radiofréquences et des micro-ondes.
•฀Les accessoires illustrés à la p. 28–29 sont approuvés pour une utilisation avec ce produit. L’utilisation d’accessoires autres que ceux précisés peut entraîner des niveaux d’exposition aux RF supérieures aux
limites établies par la FCC en matière d’exposition aux RF sans fil.
Afin de vous assurer que votre exposition à
une énergie électromagnétique de RF se situe
dans les limites permises par la FCC pour une
utilisation grand public, veuillez en tout temps
respecter les directives suivantes:
31
•฀NE PAS faire fonctionner la radio sans qu’une antenne appropriée y soit
fixée, car ceci risque d’endommager la radio et causer une exposition
supérieure aux limites établies par la FCC. L’antenne appropriée est celle
qui est fournie avec cette radio par le fabricant ou une antenne spécialement autorisée par le fabricant pour être utilisée avec cette radio.
• NE PAS émettre pendant plus de 50 % du temps total d’utilisation de
l’appareil («50 % du facteur d'utilisation»). La notion «50% du facteur
d’utilisation» s’applique également au mode VOX/PTT. Émettre pendant plus de 50 % du temps total d’utilisation peut causer une exposition aux RF supérieure aux limites établies par la FCC. Lorsque le
voyant DEL rouge s’allume, cette radio est en train d’émettre. La radio
émettra si vous appuyez sur le bouton du microphone.
•฀฀TOUJOURS tenir l’antenne éloignée d’au moins 2,5 cm de votre corps
au moment d’émettre et utiliser uniquement l’attache pour ceinture Icom
illustrée à la p. 28, lorsque vous attachez la radio à votre ceinture, ou
à autre chose, de façon à vous assurer de ne pas provoquer une exposition aux RF supérieure aux limites fixées par la FCC. Pour offrir à
vos interlocuteurs la meilleure qualité de transmission possible, tenez
l’antenne à au moins 5 cm de votre bouche et légèrement de côté.
Les renseignements ci-dessus fournissent à l’utilisateur toute l’information
nécessaire sur l’exposition aux RF et sur ce qu’il faut faire pour assurer que
cette radio fonctionne en respectant les limites d’exposition aux RF établies
par la FCC.
Interférence électromagnétique et compatibilité
En mode de transmission, votre radio Icom produit de l’énergie de RF qui
peut provoquer des interférences avec d’autres appareils ou systèmes. Pour
éviter de telles interférences, mettez la radio hors tension dans les secteurs
où une signalisation l’exige. NE PAS faire fonctionner l’émetteur dans des
secteurs sensibles au rayonnement électromagnétique tels que les hôpitaux, les aéronefs et les sites de dynamitage.
Usage professionnel/contrôlé
Ce radio émetteur est utilisé dans des cas où des personnes sont exposées
en raison de leur travail, pourvu qu’elles soient conscientes du risque d’exposition et qu’elles puissent exercer un contrôle sur cette exposition.
MEMO
10
11
12
13
14
15
16
MEMO
MEMO
10
11
12
13
14
15
16
A-7016D-1EX-0a
Printed in Japan
© 2012 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : Icom Inc.
Create Date                     : 2012:03:08 08:52:57+09:00
Modify Date                     : 2012:03:15 13:20:16+09:00
Subject                         : VHF/UHF TRANSCEIVERS
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:b614a062-897c-4803-865a-b275bb256801
Document ID                     : adobe:docid:indd:873a523b-5768-11e1-ad1d-ffa1846859a2
Rendition Class                 : proof:pdf
Derived From Instance ID        : 887b19b3-56b1-11e1-b7b6-bffe7bb252b3
Derived From Document ID        : adobe:docid:indd:7c5d6874-ed5d-11e0-8281-f274f27490eb
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:8B5CD56E5E58E1118ABE8B7CF9B55B32, uuid:D663F577DF56E111A80AA77E71434684, uuid:D863F577DF56E111A80AA77E71434684, uuid:7C5A46E86D57E11190FBEFF4C625EFA1, uuid:7D5A46E86D57E11190FBEFF4C625EFA1, uuid:23A646544458E1118ABE8B7CF9B55B32, uuid:2312D7BBE056E111A80AA77E71434684, uuid:6A79848F7658E1118E1CD5E3224A8E40, uuid:6665015A7F57E111AAC6A7CAE03017A3, uuid:BA20EFF9C956E111A80AA77E71434684, uuid:701848B66358E1118ABE8B7CF9B55B32, uuid:26A646544458E1118ABE8B7CF9B55B32, uuid:2602AB17E256E111A80AA77E71434684, uuid:2BA646544458E1118ABE8B7CF9B55B32, uuid:946F0795A557E111AAC6A7CAE03017A3, uuid:C120EFF9C956E111A80AA77E71434684, uuid:8C5CD56E5E58E1118ABE8B7CF9B55B32, uuid:210DA6731B21DF118327B10B9B3257B8, uuid:8D5CD56E5E58E1118ABE8B7CF9B55B32, uuid:5F65015A7F57E111AAC6A7CAE03017A3, uuid:2802AB17E256E111A80AA77E71434684, uuid:7B55B249039CDC11864D9281DF4F0729, uuid:2C52702E049CDC11864D9281DF4F0729, uuid:878E82A2DD56E111A80AA77E71434684, uuid:8C8E82A2DD56E111A80AA77E71434684, uuid:CE63F577DF56E111A80AA77E71434684, uuid:D163F577DF56E111A80AA77E71434684, uuid:D463F577DF56E111A80AA77E71434684, uuid:2C02AB17E256E111A80AA77E71434684, uuid:915CD56E5E58E1118ABE8B7CF9B55B32, uuid:DF3826C22968E111A96AF0CEF0C98364, uuid:E03826C22968E111A96AF0CEF0C98364
Manifest Reference Document ID  : uuid:8A5CD56E5E58E1118ABE8B7CF9B55B32, uuid:D563F577DF56E111A80AA77E71434684, uuid:D763F577DF56E111A80AA77E71434684, uuid:785A46E86D57E11190FBEFF4C625EFA1, uuid:7A5A46E86D57E11190FBEFF4C625EFA1, uuid:2012D7BBE056E111A80AA77E71434684, uuid:2212D7BBE056E111A80AA77E71434684, uuid:A519247AE156E111A80AA77E71434684, uuid:A819247AE156E111A80AA77E71434684, uuid:B920EFF9C956E111A80AA77E71434684, uuid:6F1848B66358E1118ABE8B7CF9B55B32, uuid:CC668DF1009CDC11864D9281DF4F0729, uuid:2502AB17E256E111A80AA77E71434684, uuid:2AA646544458E1118ABE8B7CF9B55B32, uuid:318B6CD7A29DDC118DAE8430C68A7ECC, uuid:C020EFF9C956E111A80AA77E71434684, uuid:E381F0E9D356E111A80AA77E71434684, uuid:51C0E08A029CDC11864D9281DF4F0729, uuid:E781F0E9D356E111A80AA77E71434684, uuid:E981F0E9D356E111A80AA77E71434684, uuid:2702AB17E256E111A80AA77E71434684, uuid:7A55B249039CDC11864D9281DF4F0729, uuid:7C55B249039CDC11864D9281DF4F0729, uuid:ED81F0E9D356E111A80AA77E71434684, uuid:8A8E82A2DD56E111A80AA77E71434684, uuid:8F8E82A2DD56E111A80AA77E71434684, uuid:CF63F577DF56E111A80AA77E71434684, uuid:D263F577DF56E111A80AA77E71434684, uuid:511B124D3C4DE1119210F3B48169E1CA, uuid:531B124D3C4DE1119210F3B48169E1CA, uuid:77B3513E3345E011BA7A8DD09B00F17F, uuid:822582BDA144E0119BB68EB5CA7FC72C
Metadata Date                   : 2012:03:15 13:20:16+09:00
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 5732 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : IC-F3161/F4161 Instruction Manual
Creator                         : Icom Inc.
Description                     : VHF/UHF TRANSCEIVERS
Light Source                    : Unknown
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 40
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AFJ340202

Navigation menu