ICOM orporated 360300 Wireless Access Point User Manual AP 90M Connection ENG 1 indd

ICOM Incorporated Wireless Access Point AP 90M Connection ENG 1 indd

TempConfidential_(AP-90M) UserMan_20150514

Download: ICOM orporated 360300 Wireless Access Point User Manual AP 90M Connection ENG 1 indd
Mirror Download [FCC.gov]ICOM orporated 360300 Wireless Access Point User Manual AP 90M Connection ENG 1 indd
Document ID2631202
Application IDarjw4+eV2NtACKRiYKLPOg==
Document DescriptionTempConfidential_(AP-90M) UserMan_20150514
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize121.23kB (1515423 bits)
Date Submitted2015-06-01 00:00:00
Date Available2015-12-19 00:00:00
Creation Date2015-05-08 10:33:40
Producing SoftwareAdobe PDF Library 8.0
Document Lastmod2015-05-14 09:32:25
Document TitleAP-90M_Connection_ENG_1.indd
Document CreatorAdobe InDesign CS3_J (5.0.4)

Step 6 Changing the administrator’s password
Read the “PRECAUTIONS” leaflet first, if you have not done so.
To prevent unauthorized access, you must change the password.
qqClick [Management], then [Administrator].
wwFill out each box to change the password.
CONNECTION GUIDE
eeClick [Apply.]
Thank you for purchasing this Icom product. The AP-90M
wireless access point is designed and built with Icom’s
IP network technology. It complies with the “IEEE802.11ac”
and “IEEE802.11n” standards, and is designed for dual
band communications in the 5 GHz and 2.4 GHz bands.
WIRELESS ACCESS POINT
AP-90M
Click
* Enter the new administrator’s password from now on.
 OTE: If you have forgotten your password, you cannot
access the AP-90M’s setting screen.
When you forgot your password:
Hold down the [MODE] button by following the instructions
described in the precautions guide. The AP-90M will have
to be reset as its default.
Enter
Step 7 DFS function and channel auto setting
The DFS function automatically avoids radio-frequency interference to Weather radars. The DFS conditions differ, depending on
your location.
	NOTE: Whether or not the DFS function is enabled on a frequency is regulated by the local law, and cannot be disabled by
users.
• The Wireless Bridging is not activated if a channel is used that requires the DFS function or if automatic channel selection is set.
Refer to the PDF instruction manual on the Icom’s website for setting details.
• The usable wireless LAN frequencies and channels differ, depending on your location.
➥➥ After setting a channel in the setting screen, restart the
AP-90M. The AP-90M will then search for a weather radar’s signal for approximately 1 minute.
	While searching for a signal, [WIRELESS 1 or 2] will blink,
and access to the AP-90M will be paused.
	When a weather radar’s signal is detected, the operating
channel automatically changes to a different channel to
avoid the interference.
➥➥ The DFS function pauses on the new channel, if the channel does not require the DFS.
Step 1 cSystem Requirements
DDSupplied Accessories
DDOther requirements
• Cushion sheet… ………… 1
• Antenna… ………………… 2
• Mounting bracket set… … 1
• Precautions guide
• “Setting the interface language and the Time Zone” leaflet
• Connection Guide (This guide)
• PC
• Ground wire
• LAN cable
• Power adapter
(The adapter type differs, depending on the access point version)
About this Connection Guide:
This Connection Guide explains the basic operation of the
AP-90M. Access our website to download the instruction
manual.
NOTE:
• Adobe® Reader® is required on your PC in order to display the
downloaded PDF instruction manual.
• If your PC does not have Adobe® Reader®, please download it
from the Adobe® website.
Icom website http://www.icom.co.jp/world/
Step 2 Panel description
[WIRELESS 2]
[WIRELESS 1]
[LAN]
[POWER]
DC jack
[WPS]
Wi-Fi Protected Setup
*The “IEEE802.11ac” standard can only be used when the 5
GHz band is selected.
IR
LE
-9
AP
0M
IN
Antenna
connector
[WIRELESS 1]: Internal antenna.
[WIRELESS 2*]: External antenna.
Back side
[MODE]
Refer to “Resetting to the
factory defaults” in the Precautions Guide, for details.
[USB] port
(USB 2.0)
[LAN] port
(RJ-45)
Ground terminal
Antenna connector
DDAbout the indicators
LED
Green
Lights
ON
Blinks
—
“Accessing the USB flash
drive” error
“Duplicated IP address” error
Lights
Red
POWER*1
Blinks
Lights
Accessing the USB flash drive.
A firmware update is ready.
Blinks
Booting.
Operating [MODE].
Orange
OFF
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
Microsoft, Windows and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
Adobe and Adobe Reader are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
–4–
OFF
WIRELESS 1
(Internal antenna)*2
LAN
LAN connected
(1000BASE-T)
LAN is communicating (1000BASE-T)
WIRELESS 2
(External antenna)*2
More than 1 connection/WPS succeeded
WPS is running
—
—
—
LAN connected
(10BASE-T/
100BASE-TX)
LAN is communicating
(10BASE-T/
100BASE-TX)
LAN is not connected
WPS failed
Internal antenna enabled
(Wireless unit is not connected)
External antenna enabled
(Wireless unit is not connected)
Wireless operation is standing by for DFS
Internal antenna disabled*3
External antenna disabled*3
*1 When the LED OFF Mode is set to “Enable,” the light is dimmed, and when set to “Enable (Completely),” the light turns OFF. (Default: Disable)
*2 When there is no wireless device to communicate with the AP-90M, or no wireless communication is performed while the Wireless Unit is
enabled, the LED lights orange. The time when the LED turns orange differs, depending on the communication status.
*3 The LED also turns OFF when the same Wireless Mode is set to the internal antenna and the external antenna.
–1–
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7168W-2EX-q Printed in Japan
© 2014–2015 Icom Inc.
Step 3 Connecting and turning ON the power
Step 4 About the setting screen
Follow the steps (q to y) to connect with the AP-90M, and check the indications as described below.
About the setting screen
About the setting screen
• If you are connecting the AP-90M with its default settings, disconnect the networks from your PC.
• If [LAN] does not light, check the LAN cable and try again.
The following procedures describe how to use the
AP-90M setting screen using a web browser.
• To check the setting screen’s online instructions, place the cursor
on a setting item, and click “?” when it appears.
Green
[LAN]:
Green/Orange*1
[WIRELESS1]: Orange
[WIRELESS2]: Orange
45º
Rotate to
the right
Sheet
Hole
*1 Indication differs,
depending on the status
0º
*2 Before attaching the
supplied mounting
bracket, first install the
supplied magnets into
the holes.
-9
LE
IR
eD
th
To
Cushion sheet
(Supplied)
IN
For the best performance, attach both antennas.
In case you find difficulties receiving signals,
change the antenna’s direction or its location.
jac
the
To
Connect
cables
N]
por
[LA
the
To
d te
gro
AP-90M
(Default:192.168.0.1)
min
AC outlet
Power adapter
(Purchase separately)
LAN cable
r Connecting the
power adapter
t Start the PC
RWARNING!
The AP-90M’s IP address is set to “192.168.0.1”, and DHCP
server to “Disable” as default. Set the connecting PC to
“192.168.0.100”.
See the PC’s instruction manual for the IP address setting
details.
To prevent electrical shock, television interference (TVI),
broadcast interference (BCI) and other problems, ground the
AP-90M through the ground terminal.
NEVER connect the ground terminal to a gas or electric pipe.
This may result in an electrical shock or cause a fire.
DDAbout default settings
Setting screen
Setting
Title
Network Settings
IP Address
IP Address
Wireless Settings
DHCP Server
Wireless LAN
DHCP Server
Wireless LAN
IP Address
Subnet Mask
DHCP Server
Frequency Band
Virtual AP
Bandwidth
Interface
Virtual AP
Security
Management
Administrator
Administrator Password
SSID
Authentication
Encryption
Username
Current Password
*3 The wireless LAN unit for Wireless 1 (internal antenna) and Wireless 2 (external antenna).
Wireless 1 and 2’s frequency bands cannot be used when both of them are set to 2.4 GHz or 5 GHz.
The “IEEE802.11ac” standard can only be used when 5 GHz is selected in Wireless 2 (external antenna).
–2–
//192.168.0.1/.”
• The Login Authentication screen will appear.
e	Enter “admin” (fixed username) and “admin” (default password) in their respective input fields in the Login Authentication window, and then click [OK].
q Link to the Icom web site
If your PC is connected to the Internet, click the Icom logo to
open the Icom web site.
w Setting menu
q Enter
Displays the screen name list on a menu line. When you
click each menu title, a list of items drops down which you
can use to select the desired setting item.
• When accessing the web browser for the first time, setting the
time zone is required. See the “Setting the interface language and
the Time Zone” leaflet for details.
e Setting screen
Displays the settings and values when you click the screen
name.
r Setting buttons
Save or cancel the setting values.
If “A reboot is required to apply all the new settings” is displayed on the screen when you click [Apply], click [Reboot].
The AP-90M reboots, and the setting items and values are
updated.
• Choose one that is not easy to guess.
• Use numbers, characters and letters (both lower and upper case).
IP address for PC
Menu
Enter
192.168.0.1/
To prevent unauthorized access
You must carefully chose your password, and change
it occasionally. See page 4 of this connection guide for
password setting details.
(Purchase separately)
(Purchase separately
:Category 5e or higher)
w Click
Ground terminal
Ground wire
PC
(Example:192.168.0.100)
q	Open your web browser, then enter the IP address of the
AP-90M into the address bar.
*The default IP address is “
w Push the [ENTER] key.
0M
Antenna ×2
(Supplied)
AP
sheet
q Cushion
attachment*
check
y Indication
[POWER]:
90º
Antenna attachment
About web browsers
We recommend using Microsoft Internet Explorer 9 or
later versions with the AP-90M.
Enable JavaScript® and set to allow Cookies on your web
browser to correctly display the setting screen.
If other browsers are used, the screen may not be
correctly displayed.
The above message is displayed on the screen while the
AP-90M is rebooting.
• If the AP-90M is still rebooting, clicking [Back] does not return to the
setting screen. Retry when the rebooting is complete.
• Items and buttons may differ, depending on the setting.
Default setting
192.168.0.1
255.255.255.0
Disable
2.4 GHz (Wireless 1)*3
5 GHz (Wireless 2)*3
20 MHz
ath0 (Wireless 1)
ath4 (Wireless 2)
WIRELESSLAN-0
Open System/Shared Key
None
admin (Cannot be changed)
admin (Lower case letters)
Step 5 Connecting with wireless LAN
The following procedures describe how to connect to the AP-90M through a wireless LAN, based on Microsoft® Windows® 7.
e	
Select the SSID set to the AP-90M and click [Connect].
Then follow the instructions.
q	
Start the AP-90M, and then turn ON the PC.
w Click the Wireless Network Connection icon.
• It may take a few minutes until the icon appears.
q Select
w Click
• The SSID is set to “WIRELESSLAN-0” by default.
Click
–3–
INFORMATION SUR LE RÉSEAU LOCAL SANS FIL
■ Précautions pour l'utilisation du réseau local sans fil
■ Lieu d'installation du réseau local sans fil
Tenir compte des conditions d'installation ci-dessous
pour ne pas réduire la portée et la vitesse de communication.
Pour les versions USA et canadienne
• Cet appareil est restreint à une utilisation à l'intérieur, dans
la bande de fréquences 5150–5250 MHz.
• L'utilisation à l'extérieur n'est pas autorisée, dans la bande
de fréquences 5150–5250 MHz.
POINT D'ACCÈS SANS FIL
AP-90M
normes IEEE802.11ac/n/a/b/g
Communications à double bande
• Des erreurs de données de communication peuvent survenir lorsque cet appareil est placé trop près du terminal
du réseau local sans fil. Prévoyez au moins un mètre (3,3
pieds) de distance entre les deux.
Pour toutes les versions
• Installer l'appareil à l'intérieur dans un endroit aussi dégagé
que possible.
• Nous recommandons aux utilisateurs portant un stimulateur cardiaque de s'assurer que cet appareil ne cause pas
de problème d'interférences électromagnétiques.
• Installer l'appareil dans un endroit stable où il ne risque pas
de tomber ou d'être soumis à des vibrations.
• NE PAS utiliser cet appareil à proximité d'un four à microondes.
	Un four à micro-ondes peut provoquer des interférences
électromagnétiques pendant les communications à l'aide
de cet appareil.
• NE PAS placer d'objets sur l'appareil.
• La portée des communications s'élargit dans un espace
ouvert. Cependant, dans des endroits tels que des entrepôts dont les murs sont métalliques, les ondes radio peuvent rebondir.
	Les ondes radio peuvent traverser un mur ou une fenêtre,
mais pas les surfaces métalliques.
	Certains murs de béton sont armés de métal et peuvent
intercepter les communications.
	Le verre anticalorique ou absorbant l'infrarouge peut intercepter les communications.
• NE PAS modifier l’appareil. L’appareil ne couvre pas les
problèmes résultant d'une modification non autorisée.
■ Communication par la bande passante
située entre 40 et 80 MHz
• Il pourrait être impossible d'établir la communication avec
un réseau local sans fil installé sur un autre étage.
• Lorsque vous utilisez le mode de bande passante de 40 ou
80 MHz du réseau local sans fil, vérifiez d'abord l'environnement d'ondes radioélectriques autour de vous afin de ne
pas créer d'interférences avec d'autres stations radio.
• Si vous avez créé des interférences nuisibles à une station
radio en utilisant cet appareil, placez la “bande passante” à
“20 MHz” (par défaut).
➥➥ Consultez le manuel d'instructions sur le site Web d'Icom
pour en savoir plus sur les bandes passantes.
Merci d'avoir choisi un produit Icom. Le POINT D'ACCÈS
SANS FIL AP-90M est conçu et fabriqué selon la technologie de réseau IP d'Icom. Nous espérons que vous adhérez à la philosophie Icom de “technologie d'abord”. De
nombreuses heures de recherche et développement ont
été nécessaires à la conception de l’AP-90M.
PRÉCAUTIONS
IMPORTANT
INFORMATION SUR LA FORMATION
À LA SÉCURITÉ
LIRE ATTENTIVEMENT ET INTÉGRALEMENT CE
MANUEL avant toute utilisation de l’AP-90M.
CONSERVEZ CES INSTRUCTIONS — Elles contien-
Cet appareil a été testé et homologué avec ses accessoires
d'origine en vue de la conformité FCC. L'utilisation d'accessoires tiers peut ne pas être conforme aux exigences imposées par la FCC pour la conformité à l'exposition aux fréquences radio et doit être évitée.
nent des renseignements importants sur la sécurité et l'utilisation de l'AP-90M.
POUR LE CANADA
Canada, avis dʼIndustry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes
de licence RSS standard(s). Son fonctionnement est soumis
aux deux conditions suivantes:
(1) cet appareil ne doit pas causer d'interférence et (2) cet
appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
iii	le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725–5825 MHz) doit se conformer à la
limite de p.i.r.e. spécifiée pour l’exploitation point à point
et non point à point, selon le cas.
Informations concernant lʼexposition aux fréquences
radio (RF)
i	les dispositifs fonctionnant dans la bande 5150–5250
MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux;
ii le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250–5350 MHz et 5470–5725 MHz doit
se conformer à la limite de p.i.r.e.;
 a puissance de sortie émise par l’appareil de sans fil
est inférieure à la limite d'exposition aux fréquences
radio d'Industry Canada (IC). Utilisez l’appareil de sans
fil de façon à minimiser les contacts humains lors du
fonctionnement normal.
Ce périphérique a également été évalué et démontré
conforme aux limites d'exposition aux RF d'IC dans des
conditions d'exposition à des appareils mobiles (antennes
sont supérieures à 20 cm à partir du corps d'une personne).
Cet émetteur radio IC: 202D-360300 a été approuvé par Industrie Canada pour fonctionner avec les types d'antennes
énumérés ci-dessous avec le gain maximal admissible et impédance d'antenne requise pour chaque type d'antenne indiqué.
Types d'antennes n'est pas inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont
strictement interdits pour une utilisation avec cet appareil.
Antennes
N°
Antennes
Icom, Icom Inc. et le logo d'Icom sont des marques de commerce enregistrées d'Icom Incorporated (Japon) pour le Japon, les
États-Unis, le Royaume-Uni, l'Allemagne, la France, l'Espagne, la Russie, l'Australie, la Nouvelle-Zélande et/ou d'autres pays.
Microsoft et Windows sont des marques déposées de Microsoft Corporation aux États-Unis et dans d’autres pays.
Adobe et Adobe Reader sont des marques déposées d'Adobe Systems Incorporated aux États-Unis et dans d'autres pays.
Tous les autres produits et toutes les autres marques sont des marques déposées ou non appartenant à leur titulaire respectif.
–4–
N° de pièce
Type d'antenne
Antenne externe
C1251-510008-A
dipôle
Antenne interne
3ARNRA001S1
dipôle
Gain maximal
3,00 dBi pour 2,4 GHz
5,00 dBi pour 5,15 à 5,25 GHz
5,00 dBi pour 5,25 à 5,35 GHz
5,00 dBi pour 5,47 à 5,725 GHz
5,00 dBi pour 5,725 à 5,825 GHz
1,15 dBi pour 2,4 GHz
2,73 dBi pour 5,15 à 5,25 GHz
2,73 dBi pour 5,25 à 5,35 GHz
3,24 dBi pour 5,47 à 5,725 GHz
3,24 dBi pour 5,725 à 5,825 GHz
Impédance
50 Ω valeur nominale
50 Ω valeur nominale
NOTE: Le connecteur d'antenne est de type SMA inversé.
–1–
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7168W-5EX-w Printed in Japan
© 2014–2015 Icom Inc.
DÉFINITIONS EXPLICITES
MISE EN GARDE: NE PAS utiliser ou placer l'AP-90M
■ Autres précautions
Risque de blessures corporelles, d'incendie ou de choc électrique.
dans des endroits où la température est inférieure à 0°C
(+32°F) ou supérieure à +40°C (+104°F).
Risque de dégât matériel.
MISE EN GARDE: NE PAS exposer l'AP-90M directe-
• Pour tout renseignement sur la façon d'utiliser le PC ou les
périphériques externes, se reporter aux manuels d'instructions de ces appareils.
La non prise en compte peut entraîner des désagréments. Absence de risque de blessures corporelles, d'incendie ou de choc électrique.
MISE EN GARDE: NE PAS utiliser l'AP-90M dans des
TERME
R AVERTISSEMENT!
MISE EN GARDE
NOTE
PRÉCAUTIONS (suite)
DÉFINITION
ment aux rayons du soleil. Cela pourrait l'endommager.
• Le bloc d'alimentation externe optionnel peut devoir être
remplacé occasionnellement, selon sa durée de vie utile.
La durée de vie d'un bloc d'alimentation externe peut varier
selon l'environnement ou les conditions dans lesquels il est
utilisé.
champs magnétiques intenses ou dans une zone de forte électricité statique. Cela pourrait l'endommager.
MISE EN GARDE: Débrancher le bloc d'alimentation ex-
INFORMATION FCC
PRÉCAUTIONS
■ Pour l'AP-90M
Cet appareil respecte les conditions établies au paragraphe
15 des règles de la FCC. Son utilisation est soumise au respect de deux conditions : (1) Cet appareil ne doit pas causer d'interférences nuisibles et (2) cet appareil doit accepter
toute interférence reçue, y compris les interférence pouvant
entraîner un fonctionnement non désiré.
R AVERTISSEMENT! NE JAMAIS utiliser un bloc d'ali-
mentation externe autre que celui indiqué. Cela pourrait provoquer un choc électrique ou un incendie ou endommager
l'AP-90M.
R AVERTISSEMENT! NE JAMAIS utiliser d'accessoi-
Tout changement ou modification, non expressément approuvé par Icom Inc., peut annuler l'autorisation de l'utilisateur à utiliser cet appareil conformément à la réglementation
FCC.
res non spécifiés. Cela pourrait provoquer un choc électrique
ou un incendie ou endommager l'AP-90M.
R AVERTISSEMENT! NE JAMAIS tenter de brancher
le bloc d'alimentation externe à une prise [CC] autre qu'à
celle située sur le panneau arrière de l'AP-90M. Cela pourrait
provoquer un choc électrique ou un incendie ou endommager l'AP-90M.
POUR LES RAYONNEMENTS NON INTENTIONNELS DE CLASSE B:
Cet équipement a été testé et reconnu conforme aux limites
fixées pour un appareil numérique de classe B, conformément au point 15 de la réglementation FCC. Ces limites ont
été fixées afin d'assurer une protection raisonnable contre
les interférences nocives dans une installation résidentielle.
Cet équipement génère, utilise et peut émettre un rayonnement de fréquence radio. S'il n'a pas été installé conformément aux instructions, il peut par ailleurs créer des interférences perturbant les communications radio. Toutefois, il n'y
a aucune garantie que les interférences ne se produiront pas
dans une installation particulière. Si cet équipement crée
des interférences perturbant la réception de la radio ou de
la télévision, comme cela peut être déterminé en éteignant
et en allumant l'équipement, l'utilisateur est invité à essayer
de corriger l'interférence en prenant une ou plusieurs des
mesures ci-après:
R AVERTISSEMENT! NE JAMAIS démonter, modifier
ou tenter de réparer l'AP-90M. Cela pourrait provoquer un
choc électrique ou un incendie ou endommager l'AP-90M.
R AVERTISSEMENT! NE JAMAIS démonter, modifier
ou tenter de réparer l'AP-90M. Cela pourrait provoquer un
choc électrique ou un incendie ou endommager l'AP-90M.
R AVERTISSEMENT! NE JAMAIS utiliser ni manipuler
l'AP-90M avec les mains mouillées, au risque d’être victime
d’un choc électrique ou d’endommager l'AP-90M.
• Réorienter ou changer de place l'antenne de réception.
• Éloigner l'équipement et le récepteur.
• Connecter l'équipement sur une prise sur un autre circuit
que celui sur lequel le récepteur est connecté.
• Faire appel au revendeur ou à un technicien radio/TV expérimenté.
MISE EN GARDE: NE PAS utiliser de solvants agressifs
tels que l'essence ou l'alcool pour nettoyer l'AP-90M, en raison des risques d'endommager la surface du AP-90M. Essuyer l’AP-90M avec un chiffon doux et sec en cas de dépôt de poussière ou de salissures. Toujours placer l'AP-90M
dans un endroit sécuritaire afin d'éviter tout contact accidentel avec des enfants.
R AVERTISSEMENT! NE JAMAIS utiliser le bloc d'alimentation externe avec un appareil autre que l'AP-90M. Cela
pourrait provoquer un choc électrique ou un incendie ou endommager le bloc d'alimentation externe.
R AVERTISSEMENT! Brancher le bloc d'alimentation à
une prise de courant continu de 100 à 240 V. Toute autre
source de courant pourrait provoquer un choc électrique ou
un incendie ou endommager le bloc d'alimentation externe.
R AVERTISSEMENT! NE JAMAIS installer le bloc d'alimentation externe dans un endroit humide, à l'extérieur ou à
proximité d'un humidificateur. Cela pourrait provoquer un choc
électrique ou un incendie ou endommager le bloc d'alimentation externe.
R AVERTISSEMENT! NE JAMAIS relier la borne de
R AVERTISSEMENT! NE JAMAIS utiliser l'AP-90M
R AVERTISSEMENT! NE JAMAIS modifier, plier avec
force, tordre, tirer ou chauffer le fil du bloc d'alimentation externe. Cela pourrait provoquer un choc électrique ou un incendie ou endommager le bloc d'alimentation externe.
pendant un orage. Une telle utilisation pourrait causer un
choc électrique ou un incendie ou endommager l'AP-90M.
Toujours débrancher le bloc d'alimentation externe avant un
orage.
R AVERTISSEMENT! Débrancher immédiatement le
bloc d'alimentation externe si l'AP-90M émet une odeur ou
un bruit inhabituel ou de la fumée. Demander conseil au distributeur Icom le plus proche.
R AVERTISSEMENT! NE JAMAIS placer l'AP-90M
dans un endroit instable (comme une surface inclinée ou un
endroit soumis à des vibrations). Cela pourrait causer des
blessures ou endommager l'AP-90M.
Avertissement d'exposition aux RF
Ce matériel doit être installé et utilisé conformément aux instructions fournies; la ou les antennes utilisées avec cet émetteur doivent être installées en prévoyant une distance de sécurité d'au moins 20 cm de toute personne et ne doivent pas
être copositionnées ni conjuguées à une autre antenne ou
à un autre émetteur. Les utilisateurs et installateurs doivent
avoir en main les instructions d'installation de l'antenne et
les conditions d'utilisation de l'émetteur pour satisfaire aux
exigences d'exposition aux RF.
■ Bloc d'alimentation externe
R AVERTISSEMENT! NE JAMAIS placer d'objets lourds
sur le fil du bloc d'alimentation externe. Cela pourrait provoquer un choc électrique ou un incendie ou endommager le
bloc d'alimentation externe.
mise à la terre à un tuyau de gaz ou à une conduite électrique. Au risque de provoquer un choc électrique ou des
brûlures.
Nous recommandons de le remplacer après environ cinq
ans d'utilisation (lorsqu'utilisé à une température ambiante
de 25°C, ou 77°F). Communiquez avec votre distributeur
local pour en savoir plus.
terne lorsque vous n'utilisez pas l'AP-90M pendant une longue
période.
R AVERTISSEMENT! NE JAMAIS toucher le bloc d'alimentation externe avec les mains mouillées. Cela peut occasionner un choc électrique ou endommager l’AP-90M.
R AVERTISSEMENT! Utiliser et placer le bloc d'alimentation externe et le câble de raccordement loin de la portée des
enfants. Ces objets peuvent provoquer un choc électrique ou
des blessures.
MISE EN GARDE: NE JAMAIS installer l'AP-90M dans
un endroit non ventilé. La dissipation de chaleur pourrait être
réduite, ce qui pourrait endommager l'AP-90M.
MISE EN GARDE: NE PAS utiliser l'AP-90M près d'un
poste de télévision ou de radio. Cela pourrait causer des parasites nuisibles.
–2–
–3–
S
0M
-9
PRECAUTIONS
LE
IR
LED indications
If you cannot access to the AP-90M setting screen, you can
reset the AP-90M by pushing [MODE] on the bottom panel.
• This resets all settings to the factory defaults.
• If you can access the setting screen, see the AP-90M instruction manual (PDF) for resetting from the setting screen.
AP
IN
RESETTING THE AP-90M
Lights (green) Light (orange)
AP-90M
Turn ON the power
IEEE802.11ac/n/a/b/g standards
Dual band communications
Blinks (orange)
Thank you for purchasing this Icom product. The AP-90M
wireless access point is designed and built with Icom’s
IP network technology. We hope you agree with Icom’s
philosophy of “technology first.” Many hours of research
and development went into the design of your AP-90M.
WIRELESS ACCESS POINT
 isconnect all cables from the AP-90M, and then conD
nect the power adapter.
• Verify that the [POWER] indicator lights green and the [WIRELESS 1 and 2] indicators light orange.
• The indicators’ status may differ, depending on the operation
status.
• If the supplied mounting bracket is attached, the [MODE]
button cannot be pushed. See the AP-90M instruction manual for the details on attaching and detaching the mounting
bracket.
 ush in and hold [MODE] with a pin on the bottom panP
el until all indicators on the front panel light orange.
 onfirm that all indicators are lit in orange, and then
release the [MODE] button.
• When the initialization has been completed, [WIRELESS 1 and 2] light orange.
All LEDs light
(orange)
IMPORTANT
Push in and hold
EXPLICIT DEFINITIONS
READ ALL INSTRUCTIONS carefully and completely
WORD
DEFINITION
Personal injury, fire hazard or electric
RWARNING! shock may occur.
Equipment damage may occur.
CAUTION
If disregarded, inconvenience only. No risk
NOTE
of personal injury, fire or electric shock.
before using the AP-90M.
Blinks (orange)
SAVE THESE INSTRUCTIONS — These instructions
contain important safety and operating instructions for the
AP-90M.
Lights (green)
Release
Light (orange)
:No light
PRECAUTIONS
:Light
:Blink
■ For the AP-90M
AUTOMATICALLY SETTING WITH A USB FLASH DRIVE
The setting data or firmware can automatically be loaded
into the AP-90M from a USB flash drive.
This is useful to recover the configuration or to update the
firmware.
NOTE:
• A USB flash drive with biometric authentication, or
password protection is not supported.
• To prevent data corruption, disconnect the AP-90M’s
power adapter when inserting or removing the USB
flash drive.
• Securely insert the USB flash drive.
• NEVER remove the USB flash drive or disconnect the
AP-90M’s power adapter, while transferring data. It will
cause data corruption, or damage the USB flash drive.
• After the firmware updating is completed, check the
firmware version in the setting window to verify that
the update was correctly done.
• When importing setting data from the USB flash drive,
the AP-90M’s original programmed setting data is
automatically saved as “bakdata.sav” on the USB
flash drive, as a backup.
• You can save multiple sets of AP-90M on one USB flash
drive and set them one by one.
• F or the safety enhancement, You can disable the
automatic setting function, or set to use the specific flash
drive.
• See the AP-90M’s PDF instruction manual on the Icom
website for details.
R WARNING! Immediately disconnect the power adapter if
the AP-90M emits an abnormal odor, sound or smoke. Contact your Icom dealer or distributor for advice.
R WARNING! NEVER use non-specified accessories.
R WARNING! NEVER put the AP-90M in any unstable
This may result in an electrical shock, cause a fire or damage the AP-90M.
place (such as on a slanted surface or vibrating place). This
may cause injury and/or damage to the AP-90M.
R WARNING! NEVER attempt to connect the power
adapter to other than the [DC] jack on the AP-90M rear panel.
This may result in an electrical shock, cause a fire or damage
the AP-90M.
CAUTION: NEVER install the AP-90M in a place without air
vents. Heat dissipation may be reduced, and this could damage the AP-90M.
CAUTION: DO NOT use the AP-90M near a television or
radio. This could cause harmful interferences.
R WARNING! NEVER disassemble, modify or repair the
AP-90M. This may result in an electrical shock, cause a fire
or damage the AP-90M.
CAUTION: DO NOT use or place the AP-90M in areas with
temperatures below 0ç (+32ƒ) or above +40ç (+104ƒ).
R WARNING! NEVER install the AP-90M in a wet place
CAUTION: DO NOT place the AP-90M in direct sunlight.
or outside. This may result in an electrical shock, cause a fire
or damage the AP-90M.
This could damage the AP-90M.
CAUTION: DO NOT use the AP-90M in strong magnetic
fields or in an area with high static electricity. This could damage the AP-90M.
R WARNING! NEVER operate or touch the AP-90M with
wet hands. This may result in an electrical shock or damage
the AP-90M.
CAUTION: Disconnect the power adapter when you will not
use the AP-90M for a long period of time.
IR
LE
-9
AP
0M
IN
The USB flash drive is not supplied. Purchase locally.
adapter. This may result in an electrical shock, cause a fire or
damage the AP-90M.
R WARNING! NEVER use other than the specified power
About the USB flash drive
Interface:
Device:
Format:
Firmly insert into
the USB port
USB 1.1 or 2.0
USB Mass Storage Class
FAT16/FAT32
(Does not support exFAT or NTFS)
Icom is not responsible for the USB flash drives used
with the AP-90M.
R WARNING! NEVER connect the ground terminal to a
gas or electric pipe. This may result in an electrical shock or
cause a fire.
or alcohol to clean the AP-90M, as they can damage the AP90M’s surfaces. If the AP-90M becomes dusty or dirty, wipe it
clean with a dry, soft cloth.
R WARNING! NEVER use the AP-90M during a thunder
and lightening storm. Using it may result in an electrical shock,
cause a fire or damage the AP-90M. Always disconnect the
power adapter before a storm.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Adobe and Adobe Reader are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
–4–
CAUTION: DO NOT use harsh solvents such as benzine
Always place the AP-90M in a secure place to avoid inadvertent contact with children.
–1–
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7168W-1EX-e Printed in Japan
© 2014–2015 Icom Inc.
PRECAUTIONS (Continued)
■ For the power adapter
■ Other precautions
R WARNING! NEVER use the power adapter with any
device other than the AP-90M. This may result in an electrical
shock, cause a fire or damage the power adapter.
• For information about operating the PC or external devices,
refer to their instruction manuals for details.
• The optional power adapter may at some time need to be
replaced, depending on its life expectancy. The life of a power adapter differs according to the environment or condition
in which the adapter is used.
R WARNING! Connect the adapter into an outlet between
100 V and 240 V AC. Otherwise, this may result in an electrical shock, cause a fire or damage the power adapter.
 e recommend replacement when it has been used for apW
proximately 5 years (When used under the ambient temperature of 25°C; 77°F). Contact your local dealer for details.
R WARNING! NEVER install the power adapter to wet place
outside or near a humidifier. This may result in an electrical
shock, cause a fire or damage the power adapter.
R WARNING! NEVER put something heavy on the power
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not
be co-located or operated in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.
adapter cable. This may result in an electrical shock, cause a
fire or damage the power adapter.
R WARNING! NEVER modify, bend by force, twist, pull or
heat the power adapter’s cable. This may result in an electrical shock, cause a fire or damage the power adapter.
R WARNING! NEVER touch the power adapter with wet
hands. This may result in an electrical shock or damage the
power adapter.
FOR CANADA (Continued)
This radio transmitter IC: 202D-360300 has been approved by Industry Canada to operate with the antenna types listed below
with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Antenna List
No.
Antenna List
Part No.
Antenna Type
External Antenna
C1251-510008-A
dipole
Internal Antenna
3ARNRA001S1
dipole
Peak Gain
3.00 dBi for 2.4 GHz
5.00 dBi for 5.15–5.25 GHz
5.00 dBi for 5.25–5.35 GHz
5.00 dBi for 5.47–5.725 GHz
5.00 dBi for 5.725–5.825 GHz
1.15 dBi for 2.4 GHz
2.73 dBi for 5.15–5.25 GHz
2.73 dBi for 5.25–5.35 GHz
3.24 dBi for 5.47–5.725 GHz
3.24 dBi for 5.725–5.825 GHz
Impedance
50 Ω Nominal
50 Ω Nominal
NOTE: The antenna connector is Reverse SMA type.
R WARNING! Use and place the power adapter and connection cable to avoid inadvertent use by children. This may
result in an electrical shock or cause injury.
WIRELESS LAN INFORMATION
FOR CANADA
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
i.	the device for operation in the band 5150–5250 MHz is
only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
ii.	t he maximum antenna gain permitted for devices in
the bands 5250–5350 MHz and 5470–5725 MHz shall
comply with the e.i.r.p. limit.
iii.	t he maximum antenna gain permitted for devices in
the band 5725–5825 MHz shall comply with the e.i.r.p.
limits specified for point-to-point and non point-to-point
operation as appropriate.
Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this
device under FCC regulations.
FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below
the Industry Canada (IC) radio frequency exposure limits.
The Wireless Device should be used in such a manner such
that the potential for human contact during normal operation
is minimized.
This device has also been evaluated and shown compliant
with the IC RF Exposure limits under mobile exposure conditions. (Antennas must maintain a separation distance of
more than 20cm from a person’s body)
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•C
 onnect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•C
 onsult the dealer or an experienced radio/TV technician
for help.
–2–
■ Precautions on using the wireless LAN
■ Wireless LAN installation location
For the USA/Canadian version
• Operation of this device in the 5150 – 5250 MHz frequency
range is restricted to indoor operation only.
Have the following installation conditions under consideration so that the communication range and speed are
not affected.
• Outdoor operation in the 5150–5250 MHz frequency range
is prohibited.
• Data communication errors may occur if the wireless LAN
terminal and this device are too close to each other. Keep
them at least 1 meter (3.3 ft) away from each other.
For all versions
• Install the device in as open a place as possible indoors.
• Use this product outdoors according to your local law.
• Install the device in a stable place where there is no danger
of falling or vibration.
• We recommend that users with pacemakers take precautions to be sure that this device does not cause them a
problem because of electromagnetic interferences.
• Do not place anything on top of this device.
• The communication range expands in an open space. However, in such location as warehouses with metallic walls, the
walls may cause the radio waves to reflect.
	Radio waves may pass through a wall or window, but not
through metal.
	Some concrete walls are metal reinforcing structures, and
may intercept the communication.
	Heat absorbing glass or IR reflecting glass may intercept
the communication.
• Do not use this device near microwave ovens.
	A microwave oven may cause electromagnetic interference
to the communications through this device.
• Do not modify the device. The device warranty does not
cover any problems caused by unauthorized modification.
■ Communicating with the 40/80 MHz
bandwidth
• Communication may not be able to be performed with a
wireless LAN installed on a different floor.
• When you are using the 40 MHz or 80 MHz bandwidth
mode on the wireless LAN, first check the radio wave environment around in order to not to interfere other radio stations.
• In case you have harmfully interfered a radio station using
this device, set the “Bandwidth” to “20 MHz (default).”
➥➥ Refer to the instruction manual on the Icom website
about the bandwidth details.
SAFETY TRAINING INFORMATION
This device was tested and approved with or iginal
accessories to ensure FCC Compliance. The use of thirdparty accessories may not comply with FCC RF exposure
compliance requirements, and should be avoided.
–3–

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Instance ID                     : uuid:5a81e8aa-e363-49d5-bef2-4c29dd508579
Document ID                     : adobe:docid:indd:c10ca821-ddbb-11e4-a8c9-c6e116367a6f
Rendition Class                 : proof:pdf
Derived From Instance ID        : c10ca820-ddbb-11e4-a8c9-c6e116367a6f
Derived From Document ID        : adobe:docid:indd:7464bd7b-281f-11e4-b2e5-f49b790450ec
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:C490FB67A44DDF11A150C084CC55CA4F, uuid:594A2A143270E211B796E18151F2AB92, uuid:3384CB4A2E70E211B3AB979430DE51D0, uuid:278C4CF288FCE111830080BB91E7400A, uuid:65adda5e-5e0e-460d-97a9-fbb287d9919d, uuid:63b7250e-f75c-418b-a15a-b9a62ee9bdf4, uuid:08B3B11B76FDE11191E6D82CA5642921, uuid:b5150529-20ec-49f9-a575-acd414786a57, uuid:6F7965EBE116E411B9F9A9701E1E3E57
Manifest Reference Document ID  : uuid:C390FB67A44DDF11A150C084CC55CA4F, uuid:584A2A143270E211B796E18151F2AB92, uuid:3284CB4A2E70E211B3AB979430DE51D0, uuid:258C4CF288FCE111830080BB91E7400A, uuid:17A7143CA5FAE3119940C251E727729C, uuid:19A7143CA5FAE3119940C251E727729C, uuid:07B3B11B76FDE11191E6D82CA5642921, uuid:1BA7143CA5FAE3119940C251E727729C, uuid:6E7965EBE116E411B9F9A9701E1E3E57
Create Date                     : 2015:05:08 10:33:40+09:00
Modify Date                     : 2015:05:14 09:32:25+08:00
Metadata Date                   : 2015:05:14 09:32:25+08:00
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 11218 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : AP-90M_Connection_ENG_1.indd
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 6
Creator                         : Adobe InDesign CS3_J (5.0.4)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AFJ360300

Navigation menu