ICOM orporated 366400 VHF Digital Transceiver User Manual IC F5360D F6360D Operating Instructions

ICOM Incorporated VHF Digital Transceiver IC F5360D F6360D Operating Instructions

User Manual

OPERATING INSTRUCTIONSiF5360D 8 NXDN OPERATION <CONVENTIONAL MODE> 7 NXDN OPERATION <TRUNKING MODE> 6 NXDN OPERATION <COMMON> 5 MENU SCREEN 4 SCAN OPERATION 3 ADVANCED OPERATION 2 BASIC OPERATION 1 PANEL DESCRIPTION INTRODUCTIONVHF DIGITAL TRANSCEIVERSiF6360DUHF DIGITAL TRANSCEIVERS
iINTRODUCTIONFOREWORDThank you for purchasing this Icom transceiver.The IDAS™ NXDN™ system operation is built into your IC-F5360D v h f di gital t r a n s c e i v e r s and IC-F6360D u h f di gital t r a n s c e i v e r s .IMPORTANTFIRST, CAREFULLY READ INSTRUCTIONS q PRECAUTIONS and w INSTRUCTIONS that are provided with the transceiver.SAVE THIS OPERATING INSTRUCTIONS— This operating instructions contain additional important operating instructions for the IC-F5360D v h f d igital t r a n s c e i v e r s and IC-F6360D u h f digi tal t r a n s c e i v -e r s .NOTEThe display contents, and the hold down time period of some keys, may vary from the description in this manu-al, depending on the transceiver’s presetting.Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.IDAS is trademark of Icom Incorporated (Japan).NXDN is a trademark of Icom Incorporated and JVC KEN-WOOD Corporation.All other products or brands are registered trademarks or trademarks of their respective holders.
1-1Section 1PANEL DESCRIPTIONFront, top and side panels ......................................................1-2Microphone D..............................................................................1-2Function display ......................................................................1-3Programmable function keys .................................................1-4
1PANEL DESCRIPTION1-2Front, top and side panelsq LED INDICATORLights red while transmitting. ➥ Lights green while receiving a signal, or when the ➥squelch is open.w FUNCTION DISPLAY (p. 1-3)Displays a variety of information.e DEALER-PROGRAMMABLE KEYS [UP] and [DOWN]Desired functions can be preset. (p. 1-5)r POWER KEY [ ]Push and hold for 1 second to turn the power ON and OFF.t DEALER-PROGRAMMABLE KEYS [R], [P0], [P1], [P2], [P3]Desired functions can be preset. (p. 1-5)y MICROPHONE CONNECTOR Connect the supplied or optional microphone. NEVER connect non-specified microphones. The pin assignments may be different and the trans-ceiver may be damaged.u AF VOLUME CONTROL KNOB [VOL] Rotate to adjust the audio output level.Microphone DThe supplied or optional microphone has a PTT switch and a hanger hook.• The following functions are available when the micro-phone is on or off hook (depending on the presetting): - Pauses scan when it is off-hook. - Switches to the ‘Inaudible’ mode (mute mode) when it is on-hook. - Switches to the ‘Audible’ mode (unmute mode) when it is off-hook.u AF VOLUME CONTROL KNOB [VOL]q LED INDICATOR e DEALER PROGRAMMABLE KEYS [UP], [DOWN]r POWER KEY [ ]t DEALER-PROGRAMMABLE KEYS [R], [P0], [P1], [P2], [P3]w FUNCTION DISPLAYSPEAKERy MICROPHONE CONNECTOR
1PANEL DESCRIPTION1-3Function displayq SIGNAL STRENGTH INDICATOR Displays the relative receive signal strength.w LOW OUTPUT POWER ICON Displayed when low output power is selected.e AUDIBLE ICON Displayed when the channel is in the ‘audible’ (un-mute) mode.r SCRAMBLER ICON Displayed when the Voice Scrambler function is ON.t SCAN ICON Displayed while scanning.y MESSAGE ICON Displayed when a received message (Short Data ➥Message or Status Message) is stored in the memory stack. Blinks when an unread message is in the memory ➥stack.u BELL ICON Blinks when a matched signal is received, depend-ing on the presetting.i GPS ICONDisplayed when position data is received.o HORN ALERT ICONDisplayed when the Horn Alert function is ON.!0 PUBLIC ADDRESS ICONDisplayed when the Public Address function is ON.!1 ALPHANUMERIC READOUT Displays the operating channel number, channel name, menu contents, DTMF code, and so on. • The display mode automatically switches between one line and two lines.!2 KEY ICONS  Display the assigned function of the [P0], [P1], [P2] and [P3] dealer assignable keys.!3 SCAN TARGET ZONE ICON Displayed when the scan target zone is selected.!4 PA SPEAKER ICON Displayed when the External speaker function is ON. When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will activate.!5 AUX A ICON Displayed when the AUX A port is activate.!6 AUX B ICON Displayed when the AUX B port is activate.!7 SCAN TARGET CHANNEL ICON Displayed when the scan target channel is selected.!8 OPERATOR SELECTABLE TONE ICON Displayed when the OST (Operator Selectable Tone) function is ON.IC-F5360DCONTACT①縦横比を52×1 9にする。②拡大200%③拡大150%qw e r t y u i o !0!2!1 !3 !4 !5 !6 !7 !8
1PANEL DESCRIPTION1-4Programmable function keysThe programmable key functions can be assigned to the following keys:[R], [P0], [P1], [P2], [P3], [UP], [DOWN] and to the key-pad keys of the optional DTMF microphone.[UP], [DOWN][R], [P0], [P1], [P2], [P3]
1PANEL DESCRIPTION1-5Programmable function keys (Continued)• For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN]The key names that are in quotation marks in the fol-lowing explanations are displayed on the Function Dis-play, and indicate the assigned function of [P0], [P1], [P2] and [P3].NoneNo functionAutodial “ADAL” (p. 3-2)Opens the DTMF Autodial code selection screen.Autodial Programming “ADPG” (p. 3-3)Enters the DTMF code programming mode.AUX A “AUXA”Turns the AUX A port ON or OFF.AUX B “AUXB”Turns the AUX B port ON or OFF.Broadcast “BCST”Toggles between Broadcast Call and Conference Call.This key can also be used to make a Broadcast Group Call.Call 1 “CAL1”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 1.Call 2 “CAL2”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 2.Call 3 “CAL3”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 3.Call 4 “CAL4”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 4.Call 5 “CAL5”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 5.Call 6 “CAL6”Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 6.CH/GID Down “CH D”Selects the next or previous channel or GID number.CH/GID Recall “CHRC”❍ In the Analog mode or NXDN Conventional systemSelects the last used channel during a scan.❍ In the NXDN Trunking systemSelects the last called GID during a scan.CH/GID Up “CH U”Selects the next or previous channel or GID number.Channel Entry “CHEN” (p. 2-4)Enters the Channel Entry mode.CW Message “CWMS”Sends a preset CW Message on a ‘very narrow’ chan-nel.You can use this function when a CW message is pre-set.Direct CH/GID 1 “DR 1” (pp. 2-4, 7-3)Selects the channel or GID that is set to Direct CH/GID 1.Direct CH/GID 2 “DR 2” (pp. 2-4, 7-3)Selects the channel or GID that is set to the Direct CH/GID 2.Direct CH/GID 3 “DR 3” (pp. 2-4, 7-3)Selects the channel or GID that is set to Direct CH/GID 3.Direct CH/GID 4 “DR 4” (pp. 2-4, 7-3)Selects the channel or GID that is set to Direct CH/GID 4.Direct CH/GID 5 “DR 5” (pp. 2-4, 7-3)Selects the channel or GID that is set to Direct CH/GID 5.Direct CH/GID 1 SelectThis function is for the hold down operation of [Direct CH/GID 1].Sets the selected channel or GID to Direct CH/GID 1.
1PANEL DESCRIPTION1-6Programmable function keysDirect CH/GID 2 SelectThis function is for the hold down operation of [Direct CH/GID 2].Sets the selected channel or GID to Direct CH/GID 2.Direct CH/GID 3 SelectThis function is for the hold down operation of [Direct CH/GID 3].Sets the selected channel or GID to Direct CH/GID 3.Direct CH/GID 4 SelectThis function is for the hold down operation of [Direct CH/GID 4].Sets the selected channel or GID to Direct CH/GID 4.Direct CH/GID 5 SelectThis function is for the hold down operation of [Direct CH/GID 5].Sets the selected channel or GID to Direct CH/GID 5.Display Format “DISP”❍ In the Analog mode or NXDN Conventional systemToggles the display format between the channel name and the zone and channel number.❍ In the NXDN Trunking systemToggles the display format between the GID name and the GID number.Emergency (p. 3-5)This function can be assigned only for [R].Enters the Emergency mode.External Speaker “EXSP”Turns the External speaker function ON or OFF.When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will be activated.Fixed Volume “FIXV”Toggles the tone level between “High” and “Low,” or turns OFF the tone.Forced Search “FORS”Displays the site number of the current site for 2 sec-onds.Forced Search FunctionThis function is for the hold down operation of [Forced Search].Activates a Control Channel Hunt.Function “FUNC”Activates a secondary function that is assigned to a key.This function cannot be assigned as a secondary func-tion.GPS Position Display “GPSP”Enters the GPS Position Display mode.In the GPS Position Display mode, you can check your latitude and longitude position.Group ID/Channel Entry “GIDE” (pp. 2-4, 7-3)❍ In the Analog mode or NXDN Conventional systemEnters the Channel Entry mode.❍ In the NXDN Trunking systemEnters the GID Entry mode.Group (NXDN) “GRP” (pp. 7-4, 8-3)❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode.In the NXDN Conventional system, this function is used for Group Call by recalling GID list.In the NXDN Trunking system, the GID List is displayed, but the transceiver cannot make a call.Group + SDM (NXDN) “GSMS”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode.If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Short Data Message Entry mode. See page 7-4 or 8-3 for details.Group + Status (NXDN) “GSTA”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode.If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Status Message Entry mode. See page 7-4 or 8-3 for details.High Transmit Power “HIPW”❍ In the NXDN Trunking system Toggles the transmit power level between “High” and ➥“Auto,” if “Auto” is set as the default. Toggles the transmit power level between “High” and ➥“Low,” if “Low” is set as the default.• For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
1PANEL DESCRIPTION1-7Programmable function keysHome CH/GID “HOME” (pp. 2-4, 7-3)❍ In the Analog mode or NXDN Conventional systemSelects the Home Channel.❍ In the NXDN Trunking systemSelects the Home GID.Home CH/GID Select (pp. 2-4, 7-3)This function is for the hold down operation of [Home CH/GID].❍ In the Analog mode or NXDN Conventional systemSets the selected channel as the Home Channel.❍ In the NXDN Trunking systemSets the selected GID as the Home GID.Horn Alert “HORN”Turns the Horn Alert function ON or OFF.When this function is ON, the horn alert port will be ac-tivated for a preset time period after receiving a call.Individual (NXDN) “INDV” (pp. 7-5, 7-6, 8-4)❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Individual Call mode.Individual + SDM (NXDN) “ISMS”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Individual Call mode.If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Short Data Message Entry mode. See page 7-5 or 8-4 for details.Individual + Status (NXDN) “ISTA”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Individual Call mode.If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Status Message Entry mode. See page 7-5 or 8-4 for details.LCD Brightness “BRIT”Selects the brightness of the function display and keys backlight. Select High, Low or OFF to meet your needs.The function display and keys can be backlit for better visibility under low light conditions.Lone Worker “LONE” (p. 3-5)Turns the Lone Worker function ON or OFF.Low Transmit Power “LOPW”❍ In the Analog mode or NXDN Conventional systemToggles the transmit power between “High” and “Low,” if “High” is set as the default.❍ In the NXDN Trunking system Toggles the transmit power level between “Low” and ➥“Auto,” if “Auto” is set as the default. Toggles the transmit power level between “High” and ➥“Low,” if “High” is set as the default.Maintenance “MANT”Enters the Maintenance Display mode.Menu “MENU” (p. 5-2)Displays the Menu screen.Monitor “MONI”❍ In the Analog modeTurns the Monitor ON or OFF.When the Monitor is ON, the transceiver releases the CTCSS or DTCS mute.❍ In the NXDN Conventional systemTurns the Monitor ON or OFF.When the Monitor is ON, the transceiver releases the RAN code mute.Monitor Momentary “MONI”❍ In the Analog modeWhile holding down, the transceiver releases the CTC-SS mute.❍ In the NXDN Conventional systemWhile holding down, the transceiver releases the RAN code mute.Operator Selectable Tone “OST”Turns the OST (Operator Selectable Tone) mode ON or OFF.When the OST mode is ON, the selected tone in the OST list is enabled.OST ListThis function is for the hold down operation of [Opera-tor Selectable Tone].Displays the OST (Operator Selectable Tone) list.Priority-channel Select “PRIO”Enters the Priority channel Select mode for a Priority scan.• For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
1PANEL DESCRIPTION1-8Programmable function keysPublic Address “PUBA”Turns the Public Address function ON or OFF.When this function is ON, you can make announce-ment through a PA speaker.• Transmitting is disabled while in the PA mode.Scan “SCAN”Starts or stops a scan.Scan Delete/Add “SCNE”Sets or cancels the selected channel or GID as a scan target.Scrambler/Encryption “SCRM”❍ In the Analog modeTurns the Scrambler function ON or OFF.❍ In the NXDN Conventional system or the NXDN Trunking systemTurns the Encryption function ON or OFF.Scrambler/Encryption CodeThis function is for the hold down operation of [Scram-bler/Encryption].❍ In the Analog modeEnters the Scrambler Code mode.❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Encryption Code mode.SDM (NXDN) “SMSG”❍ In the NXDN Conventional system or the NXDN Trunking systemDirectly enters the Short Message mode.Push [PTT] to send a Short Message to a Base ID.Send the GPS data “GPSD”❍ In the NXDN Conventional system or the NXDN Trunking systemSends the position data that is received from the GPS receiver to a Base station.Site Down “SIDN”❍ In the NXDN Trunking systemSelects the previous site number.If the site name is not entered, [Site Down] does not function.Site Lock “SILK”❍ In the NXDN Trunking systemTurns the Site Lock function ON or OFF.Site SelectThis function is for the hold down operation of [Site Lock].❍ In the NXDN Trunking systemEnters the Site Select mode.If the site name is not entered, [Site Select] does not function.Site Up “SITU”❍ In the NXDN Trunking systemSelects the next site number.If the site name is not entered, [Site Up] does not func-tion.Squelch Level “SQLL”❍ In the Analog modeEnters the Squelch Level Adjustment mode.Squelch Off “SQLO”❍ In the Analog mode or NXDN Conventional systemOpens the squelch, and releases the mute.Squelch Off Momentary “SQLM”❍ In the Analog mode or NXDN Conventional systemWhile holding down, opens the squelch, and releases the mute.Stack “STAK” (p. 6-3)Enters the Memory Stack mode.Status (NXDN) “STAT”Enters the Status Message mode.Push [PTT] to send a Status to a Base ID.Talk Around “TLKA”Turns the Talk around function ON or OFF.• The Talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver com-munication.Transceiver Password “PSWD” (p. 2-2)Enters the password entry mode.The transceiver cannot be used until you enter a cor-rect password.Zone Delete/Add “ZODE”Sets or cancels the selected zone as a scan target.Zone Down “ZNDN”Selects the previous zone number.Zone Up “ZNUP”Selects the next zone number.• For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
1PANEL DESCRIPTION1-9• For Keypad Operation (Microphone)Channel Entry (p. 2-4)Enters the channel number.Group ID/Channel Entry (pp. 2-4, 7-3)❍ In the Analog mode❍ In the NXDN Conventional systemEnters the channel number.❍ In the NXDN Trunking systemEnters the GID.OST (Operator Selectable Tone) Hold down [1] to [9] to select a tone that is preset in ➥the OST list.Hold down [0] to turn OFF the OST tone. ➥Hold down [ ➥M] to turn OFF the OST mode. • When the OST mode is OFF, the selected channel’s pre-set tone is used. Hold down [#], and then push the [0] to [9] digit keys ➥to enter the OST List number 1 to 40 to select a pre-set tone.AutodialSelects the DTMF Code that is preset in the Autodial List.After selecting, push [PTT] to send.Keypad Auto PTTTransmits DTMF tones.This function is enabled only when Manual Dialing is enabled.Status (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Status Message mode, and selects the Sta-tus number.SDM (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnter an SDM message.Individual (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Individual Call mode, and selects the unit ID to send an Individual Call to.Individual + Status (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Individual Call mode, and selects the unit ID to transmit an Individual Call to.If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Status Message mode.Individual + SDM (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Individual Call mode, and selects the unit ID to transmit an Individual Call to.If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Short Data Message mode.Group (NXDN)❍ In the NXDN Conventional systemEnters the Group Call mode, and selects the GID to send a Group Call to.❍ In the NXDN Trunking systemDisplays the GID List, but the transceiver cannot make a call.Group + Status (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Group Call mode, and selects the GID to transmit a Group Call to.If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Status Message mode.Group + SDM (NXDN)❍ In the NXDN Conventional system❍ In the NXDN Trunking systemEnters the Group Call mode, and selects the GID to transmit a Group Call to.If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Short Data Message mode.Programmable function keys (Continued)
2-1Section 2BASIC OPERATIONTurning power ON ....................................................................2-2Adjusting the audio level D..........................................................2-2Inputting the password D ............................................................2-2Selecting a zone ......................................................................2-3Selecting a zone D ......................................................................2-3Selecting a channel .................................................................2-4Selecting a channel D .................................................................2-4Selecting a Home channel D ......................................................2-4Directly entering a channel D ......................................................2-4Receiving ..................................................................................2-5Setting the squelch level D..........................................................2-5Transmitting .............................................................................2-6Transmitting notes D ...................................................................2-6
2BASIC OPERATION2-2Turning power ONHold down [ ➥] for 1 second to turn ON the power.Adjusting the audio level D When receiving a call, rotate [VOL] to adjust the au- ➥dio output volume level.Inputting the password D If the transceiver is preset for a start up password, en-ter the digit codes. While in the Password Entry mode, “PASSWORD” qis displayed. Push [UP] or [DOWN] to enter a digit code, and then wpush [P1] to set. • Goes to the next digit entry position. Repeat step e w until you enter the password, and then push [P1].When using the DTMF microphone:Push the [0] to [9] digit keys on the microphone to enter the password, and then push [#].NOTE: If “PASSWORD” does not disappear after pushing [P1], the password code you entered may be incorrect. In this case, enter the correct pass-word.For your reference:When [Transceiver Password] is assigned to any key, or the Transceiver Password item is preset in the Menu screen and [Menu] is assigned to any key, the start up password does not appear, even if the Trans-ceiver Password is programmed.In this case, push [Transceiver Password], or select “Transceiver Password” in the Menu screen to enter the Password Entry mode, then enter the password as described above. PASSWORD 12345Channel 1[VOL] [ ][P1] [UP] [DOWN]
2BASIC OPERATION2-3Selecting a zoneSelecting a zone DTo select a desired zone (Conventional group or NXDN Trunking system).Push [Zone Up] or [Zone Down]. ➥NOTE:When you select the Conventional group zone, see the page 2-4 for details of the channel selection.When you select the NXDN Trunking system zone, see page 7-3 for details of the GID (Group ID) selec-tion.For your reference: What is “zone?”Certain channels are grouped together and assigned to a zone according to their intended use.For example, ‘Staff A’ and ‘Staff B’ are assigned to a “Business” zone, and ‘John’ and ‘Cindy’ are assigned to a “Private” zone.
2BASIC OPERATION2-4Selecting a channelSelecting a channel DTo select a desired operating channel:Push [CH/GID Up] or [CH/GID Down]. ➥ Push one of the direct channel select keys, [Direct ➥CH/GID 1] to [Direct CH/GID 5]. • You can change the channel by pushing [Direct CH/GID 1] to [Direct CH/GID 5], as described below.Changing the Direct channel setting:Select a desired channel. q Hold down one of the [Direct CH/GID 1] to [Direct wCH/GID 5] keys for 3 seconds to set the selected channel to the Direct channel 1 to 5.Directly entering a channel DYou can select a channel by pushing [UP] or [DOWN] or the [0] to [9] digit keys on the microphone, after pushing [Channel Entry].Or, when the Channel Entry function is assigned to the keypad, you can select a channel by pushing [0] to [9] digit keys on the microphone. Push [Channel Entry] to enter the Channel Entry qmode.CH ENTER MODCH No. _ _ wPush [UP] or [DOWN] to select the channel number, and then push [P1](SEL). • Push [P0](BACK) to cancel the entry, and return to the screen that you selected before entering the Channel En-try mode. • You can use the digit keys on the microphone.Channel 1When using the DTMF microphone: Push the [0] to [9] digit keys to enter the Channel qEntry mode.CH ENTER MODCH No. _ 1 Enter the channel number, and then push [#]. w • Push [M] to delete the entered number. • Push [M] again to cancel the entry, and return to the screen that you selected before entering the Channel Entry mode.Channel 1• When the channel name is not programmed, the selected zone and channel number are displayed. (example: “1- 1”)• When the programmed channel is less than 10, you can select a channel without pushing [#].Selecting a Home channel DThe Home channel is an often-used Memory channel you can preset in the transceiver.Push [Home CH/GID]. ➥ • To change the Home channel, see the description below.Changing the Home channel setting:Select a desired channel. q Hold down [Home CH/GID Select] for 3 seconds to wset the selected channel as the Home channel.For your reference: You may be able to select a channel in the Menu screen, depending on the presetting.See section 5 for details.
2BASIC OPERATION2-5Receiving Select a channel. (p. 2-4) qPush [CH/GID Up] or [CH/GID Down]. ➥ Push one of the direct channel select keys, [Direct ➥CH/GID 1] to [Direct CH/GID 5]. Push the [0] to [9] digit keys of the optional DTMF ➥microphone to enter the channel number when the Channel Entry function is assigned to the key-pad, or after pushing [Channel Entry]. When receiving a call, rotate [VOL] to adjust the au- wdio output volume level.Setting the squelch level DThe squelch circuit mutes the received audio, depend-ing on the signal strength.Push [MENU]. q • Opens the Menu screen. Push [P2]( wΩ) or [P3](≈) to select the category that has the “SQL LEVEL” item. (Default: “UTILITY”)UTILITYPush [P1](ENT). e • Enters the Menu Item Select mode. Push [P2]( rΩ) or [P3](≈) to select the “SQL LEVEL” item.UTILITYSQL LEVELPush [P1](ENT). t • Enters the Squelch Level Adjustment mode. Push [UP] to increase the squelch level up to 9 (tight ysquelch) or push [DOWN] to decrease the squelch level down to 0 (loose squelch). • Push [P0](BACK) to return to the previous screen.LEVEL 9After setting, push [P1](EXIT). u • Closes the Menu screen.
2BASIC OPERATION2-6TransmittingWait until the channel is clear to avoid interference. Take the microphone off-hook. q • While scanning, the scan stops.Wait for the channel to become clear. w • The channel is busy when the LED indicator lights green. While holding down [PTT], speak at a normal voice elevel.Release [PTT] to receive. rNOTE:To maximize the readability of your signal:1. After pushing [PTT], pause briefly before you start speaking.2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak at your normal voice level.Transmitting notes D• Transmit inhibit functionThe transceiver has several inhibit functions which re-strict transmission under the following conditions:- The channel is busy.- An unmatched CTCSS tone or DTCS code is re-ceived, depending on the presetting.- An unmatched or matched RAN code is received, depending on the presetting.- The selected channel is a ‘receive only’ channel.• Time-out timer (TOT)After continuous transmission for a preset time pe-riod, the time-out timer causes the transceiver to stop transmitting.• TOT Rekey timerOnce transmission is cut OFF, it is further inhibited for a period determined by the TOT Rekey timer.• MDC 1200 system operationThe MDC 1200 signaling system enhances your trans-ceiver’s capabilities. It allows PTT ID signaling.When you push or release [PTT], the transceiver sends your unit ID, if preset.ID 0001When receiving a PTTIDfrom unit ID ‘0001.’
3-1Section 3ADVANCED OPERATIONDTMF Calls ...............................................................................3-2Manual Dialing D .........................................................................3-2Autodial D ...................................................................................3-2Stun function D ...........................................................................3-2Editing the Autodial list D ............................................................3-3Adding an entry to the Autodial list D ..........................................3-4Emergency Calls ......................................................................3-5Emergency Calls D .....................................................................3-5Lone Worker Emergency Call D ..................................................3-5Scrambler .................................................................................3-6Radio Access Number (RAN) .................................................3-7
3ADVANCED OPERATION3-2DTMF CallsManual Dialing D While holding down [PTT], push the keys on the ➥10-keypad to send the desired DTMF tones. • When [Keypad Auto PTT] is assigned to the keypad, you can send the DTMF tones using the DTMF keypad with-out pushing [PTT].Autodial DAutodial allows you to quickly send DTMF tones that have been pre-entered onto your transceiver.Push [Autodial]. q • The rst entry in the Autodial list appears. Push [UP] or [DOWN] to select your desired num- wber.Push [P3](TX) or [PTT] to send. eStun function DWhen the transceiver receives a stun code over the air, the stun function is activated and the transceiver opera-tion is inhibited. In this case, receiving a revive code is necessary to operate the transceiver again.This function is used when a transceiver is stolen or lost.For your reference:When the Store & Send function is enabled, you can sequentially send up to 30 of DTMF tones at one time.Push [Autodial]. q • “CODE?” appears. Push [UP] or [DOWN] to enter a digit, and then wpush [P1](SEL) to set. • Goes to the next digit entry position. • You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step e w until you enter up to 30 digits. • Push [P0](DEL) to delete the entered digit. • Push [P1](EXIT) to exit the DTMF Code Entry mode. • Push [P2](MODE) to toggle between the DTMF Code Entry mode and the DTMF Autodial code selection mode.Push [P3](TX) or [PTT] to send. r[P0], [P1], [P2], [P3][UP] [DOWN]
3ADVANCED OPERATION3-3DTMF Calls (Continued)Editing the Autodial list DPush [Autodial Programming]. qAUTDIAL PRGMAUTODIAL 1 Push [UP] or [DOWN] to select the number you want wto edit.Push [P1](ENT). e • Enters the Name Entry mode.AUTODIAL 1 Push [UP] or [DOWN] to enter a character, and then rpush [P1](SEL) to set. • Goes to the next character entry position. • You can use the 10-keypad keys of the optional DTMF microphone to enter a character. Repeat step t r until you enter a name of up to 12 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.AUTODIAL 2Push [P1](ENT) to save. y • Enters the DTMF Code Entry mode.11111 Push [UP] or [DOWN] to enter a digit, and then push u[P1](SEL) to set. • Goes to the next digit entry position. • You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step i u until you enter a DTMF number of up to 16 digits. • Push [P0](DEL) to delete a digit.11112Push [P1](ENT) to set. o • “OVERWRITE?” appears.OVERWRITE?!0 Push [P1](OK) to overwrite. • Push [P0](BACK) to return to the DTMF Code Entry mode.AUTDIAL PRGMAUTODIAL 2
3ADVANCED OPERATION3-4DTMF Calls (Continued)Adding an entry to the Autodial list DPush [Autodial Programming]. qAUTDIAL PRGMAUTODIAL 1 Push [UP] or [DOWN] to select a blank number. wAUTDIAL PRGMBLANK 04Push [P1](ENT). e • Enters the Name Entry mode. • “NAME?” appears. NAME? Push [UP] or [DOWN] to enter a character, and then rpush [P1](SEL) to set. • Goes to the next character entry position. • You can use the 10-keypad keys of the optional DTMF microphone to enter a character. Repeat step t r until you enter a name of up to 12 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.AUTODIAL 4Push [P1](ENT) to set. y • Enters the DTMF Code Entry mode. • “CODE?” appears. CODE? Push [UP] or [DOWN] to enter a digit, and then push u[P1](SEL) to set. • Goes to the next digit entry position. • You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step i u until you enter a DTMF number of up to 16 digits. • Push [P0](DEL) to delete a digit.12345Push [P1](ENT) to set. o • “STORE?” appears. STORE?!0 Push [P1](OK) to store. • Push [P0](BACK) to return to the DTMF Code Entry mode.AUTDIAL PRGMAUTODIAL 4
3ADVANCED OPERATION3-5Emergency CallsEmergency Calls DWhen [Emergency] is assigned to [R], you can manu-ally make an Emergency call.Hold down [ qR] for 1 second. • Enters the Emergency mode. • When the transceiver enters the Emergency mode, it will change to the Emergency channel and begin transmit-ting, according to the presetting. To exit from the Emergency mode, hold down [ wR] again, or turn OFF the power. • If the Emergency mode completes a preset number of call cycles, the transceiver will automatically exit the mode and return to the zone and channel that was in use before you entered the Emergency mode.Lone Worker Emergency Call DWhen the Lone Worker function is activated, the Emer-gency function is automatically turned ON, after the preset time period has passed with no operation per-formed. Push [Lone Worker] to turn the function ON or OFF. ➥NOTE:The Emergency Mode Type can be set to “Silent” or “Audible” by using the optional cloning software.When “Audible” is set, the transceiver sounds a beep when transmitting in the Emergency mode.[R]
3ADVANCED OPERATION3-6ScramblerThe Voice Scrambler function provides private commu-nication between stations. All transceiver versions have a built-in scrambler. Push [Scrambler/Encryption] to turn the function ON ➥or OFF. • “ ” appears when the Scrambler function is ON. • After turning ON the function, push [PTT] to make an encrypted call.Changing the Scrambler code setting: ✓ Hold down [Scrambler/Encryption Code] to enter the qScrambler Code Setting mode. • The length of time you hold down [Scrambler/Encryption Code] may differ, depending on the presetting.Push [UP] or [DOWN] to select a desired code. wPush [P1](EXIT) to save and exit. e • Even if the Scrambler function is OFF in step q, it auto-matically turns ON after exiting the Scrambler Code set-ting mode.
3ADVANCED OPERATION3-7Radio Access Number (RAN)RAN is a signaling system designed for digital radio communications.When a channel is set up with a RAN, the squelch will open only when a call containing a matching RAN is received.If a call containing a different RAN is made on the same channel you are using, you will not hear the call.
4-1Section 4SCAN OPERATIONScan operation .........................................................................4-2Temporary channel lockout ....................................................4-3Priority scan .............................................................................4-4Setting a Priority channel D ........................................................4-4Scan Revert channel ...............................................................4-5Scan delete/add .......................................................................4-6
4SCAN OPERATION4-2Scan operationA scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and stops when a signal is received.Push [Scan] each time to start or stop a scan. ➥ • “ ” appears while scanning. • When the transceiver detects a signal, the scan pauses on the channel. The transceiver remains on the busy channel until the signal disappears, and then the scan resumes.SCANWhile scanningNOTE: Two or more channels must be programmed to start a scan.For your reference:Before starting a scan, set the following items:• Set 3 scan types in the transceiver: Single, Multi or List.• Set the scan type in both the conventional and trunk-ing zones.• Set Priority channels, but only in conventional type zones.When you select a conventional zone, trunking zones are not scanned.When you select a trunking zone, conventional zones are not scanned.Select the desired zone to start scanning.• Single: The transceiver scans the preset target channels or GIDs in only the selected zone. For a Priority scan, all Priority channels will also be scanned, even if they are in other conventional type zones.• Multi: The transceiver scans the preset target channels or GIDs in only the preset target zones. For a Priority scan, all Priority channels will also be scanned, even if they are in other conventional type zones.• List: The transceiver scans the preset target channels or GIDs in only the zones that are preset on the Scan List. For a Priority scan, all Priority channels will also be scanned, even if they are in conven-tional type zones that are not on the List.NOTE:When the scan starts in the Conventional group zone, the NXDN Trunking system zone is not scanned.When the scan starts in the NXDN Trunking system zone, the Conventional group zone is not scanned.
4SCAN OPERATION4-3Temporary channel lockoutDuring a scan, you can temporarily delete a channel from a scanning sequence.This function speeds up scanning by skipping unwant-ed channels.Start the scan. (p. 4-2) q • When a signal is received, the scan pauses. While the scan is paused, and if you want to skip the wfrequency, push [Scan Delete/Add]. • “Ú” (scan target channel icon) disappears when the se-lected channel is deleted from the scanning sequence. • The channel is no longer scanned. However, depending on the presetting, the deleted channel may be added to the scan group again after the scan is cancelled.See also: “Scan delete/add” on page 4-6
4SCAN OPERATION4-4Priority scanThe Priority scan scans all scan target channels or GIDs in the zone while also monitoring the Priority 1 and Priority 2 channels.When the scan is paused on the Priority 1 channel, the other channels are not monitored.Setting a Priority channel DDepending on the presetting, you can manually set a Priority channel (Priority 1, Priority 2 or Priority 1 & 2). Select a channel that you want to set as a Priority qchannel.Channel 1Push [Priority-channel Select]. w • Enters the Priority Channel Setting mode.PRI CH SEL NORMAL Push [UP] or [DOWN] to select “PRIORITY 1,” e“PRIORITY 2” or “PRIORITY 1 & 2.”PRI CH SEL PRIORITY 1Push [P1](OK). r • The selected channel is set as a Priority channel.NOTE: When “PRIORITY 1 & 2” is selected, the same channel is set as both Priority 1 and Priority 2 channels.
4SCAN OPERATION4-5Scan Revert channelThe Scan Revert channel is automatically selected when you push [PTT] to make a call during a scan.The Scan Revert channel can be set to the transceiver using the optional cloning software.• Last Called + Selected: The transceiver makes a call on the last channel or GID that you received a call on. However, if you push [PTT] while the scan is paused, the transceiver makes a call on the chan-nel or to the GID that the scan is paused on. When you change the channel or GID before starting a scan, the transceiver makes a call on the selected channel or to the GID until the trans-ceiver receives another call.• Selected: The transceiver makes a call on the channel or to the GID selected before a scan.• Selected + Talkback: The transceiver makes a call on the channel or to the GID selected before a scan. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-nel or to the GID that the scan is paused on.• Priority 1: The transceiver makes a call on the Priority 1 channel.• Priority 1 + Talkback: The transceiver makes a call on the Priority 1 channel. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-nel or to the GID that the scan is paused on.• Priority 2: The transceiver makes a call on the Priority 2 channel.• Priority 2 + Talkback: The transceiver makes a call on the Priority 2 channel. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-nel or to the GID that the scan is paused on.
4SCAN OPERATION4-6Scan delete/addDuring scan, you can temporarily delete a channel or zone from the scanning sequence. Select a channel, GID or zone that you want to de- qlete from the sequence.Push [Scan Delete/Add]. w • “Ú” disappears when the selected channel, GID or zone is deleted from the scanning sequence.Channel 1To manually add a channel, GID or zone to the scan-ning sequence, repeat steps q and w.• “Ú” appears when the selected channel is added to the sequence.
5-1Section 5MENU SCREENMenu screen description ........................................................5-2Entering the Menu screen D .......................................................5-2Menu functions ........................................................................5-3
5MENU SCREEN5-2Menu screen descriptionWhen [Menu] is assigned, you can open the Menu screen.In the Menu screen, the items are categorized.Depending on the presetting, you can select various functions and adjust the transceiver settings in the Menu screen.CONTACTMenu screen (Sample)Entering the Menu screen DExample: Setting the squelch levelPush [MENU]. q • Opens the Menu screen. Push [P2]( wΩ) or [P3](≈) to select the category that has the “SQL LEVEL” item. (Default: “UTILITY”)UTILITYPush [P1](ENT). e • Enters the Menu Item Select mode. Push [P2]( rΩ) or [P3](≈) to select the “SQL LEVEL” item.UTILITYSQL LEVELPush [P1](ENT). t • Enters the Squelch Level Adjustment mode. Push [UP] to increase the squelch level up to 9 (tight ysquelch), or push [DOWN] to decrease the squelch level down to 0 (loose squelch). • Push [P0](BACK) to return to the previous screen.LEVEL 9After setting, push [P1](EXIT). u • Closes the Menu screen.For your reference:You can close the Menu screen by pushing [R], even if an item is selected.
5MENU SCREEN5-3Menu functionsAutodial “AUTO DIAL”Opens the DTMF Autodial code selection screen.When “AUTO DIAL” is displayed, push [P1](ENT). q • The rst entry in the Autodial list appears.Push [UP] or [DOWN] to select a desired number. wPush [P3](TX) to send. eWhen the Store & Send function is enabled:When “AUTO DIAL” is displayed, push [P1](ENT). q • “CODE?” appears. Push [UP] or [DOWN] to enter a digit, and then push w[P1](SEL) to set. • Goes to the next digit entry position. • You can use the 10-keypad keys on the optional DTMF microphone. Repeat step e w until you enter up to 30 digits. • Push [P0](DEL) to delete the entered digit. • Push [P1](EXIT) to exit the DTMF Code Entry mode. • Push [P2](MODE) to toggle between the DTMF Code En-try mode and the DTMF Autodial code selection mode.Push [P3](TX) to send. rAutodial Programming “AUTDIAL PRGM”Enters the DTMF Code Programming mode. When “AUTDIAL PRGM” is displayed, push [P1](ENT). q • The rst entry in the Autodial list appears. Push [UP] or [DOWN] to select a desired number. wPush [P1](ENT). e • Enters the Name Entry mode. (p. 3-3)AUX A “AUX A”Turns the AUX A port ON or OFF. When “ qAUX A” is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eAUX B “AUX B”Turns the AUX B port ON or OFF. When “ qAUX B” is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eBroadcast “BROADCAST”❍ In the NXDN Trunking systemTurns the Broadcast Call ON or OFF.This item can also be used to make a Broadcast Group Call. When “BROADCAST” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eWhen “ON” is selected in step w, push [PTT] to send the Broadcast Group Call.Direct CH/GID 1 Select to Direct CH/GID 5 Select“DIRECT CHGD1” to “DIRECT CHGD5”Sets the selected channel or GID to a Direct CH/GID between 1 and 5.Select a desired channel. (p. 2-4) qPush [MENU]. w • Opens the Menu screen. When a channel between “DIRECT CHGD1” and e“DIRECT CHGD5” is displayed, push [P1](ENT). • Sets the selected channel to a Direct channel between 1 and 5.Display Format “DISP FORMAT”❍ In the Analog mode or NXDN Conventional systemToggles the display format between the channel name and the zone and channel number.❍ In the NXDN Trunking systemToggles the display format between the GID name and the GID number. When “DISP FORMAT” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select “CH NAME” or w“ZONE-CH No.” • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eExternal Speaker “EXT SPEAKER”Turns the External speaker function ON or OFF.When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will ac-tivate. When “EXT SPEAKER” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. e
5MENU SCREEN5-4Menu functions (Continued)Fixed Volume “FIXED VOLUME”Toggles the tone level between “High” and “Low,” or turns OFF the tone. When “FIXED VOLUME” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select “LOW,” “HIGH” or w“OFF.” • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eForced Search “FORCE SEARCH”❍ In the NXDN Trunking systemStarts to search for a site. When “FORCE SEARCH” is displayed, push [P1] ➥(ENT). • Displays “SEARCHING.”GPS Position Display “GPS POS DISP”Enters the GPS Position Display mode.In the GPS Position Display mode, you can check your latitude and longitude position. When “GPS POS DISP” is displayed, push [P1] q(ENT). • You can check your latitude and longitude position. Push [UP] or [DOWN] to toggle between the latitude wand longitude position display. • Push [P0](BACK) to return to the previous screen. • Push [P1](EXIT) to the GPS Position Display mode. • Push [P2](DISP) to automatically switch the latitude and longitude position display.Group (NXDN) “GROUP MODE”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode.In the NXDN Conventional system, this function is used for Group Calls.In the NXDN Trunking system, the Group ID List is dis-played, but the transceiver cannot make Group calls. When “GROUP MODE” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select a desired GID. w Push [PTT] to call the selected GID. eGroup + SDM (NXDN) “GROUP+SDM”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode, and then the Short Data Message Entry mode. When “GROUP+SDM” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired GID. wPush [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the optional DTMF microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter. Push [PTT] to send the message to the selected yGID.Group + Status (NXDN) “GROUP+STATUS”❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Group Call mode, and then the Status Mes-sage Entry mode. When “GROUP+STATUS” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select a desired GID, and wthen push [P1](ENT). • Enters the Status Message Selection mode. Push [UP] or [DOWN] to select the status message ethat you want to send. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the selected rGID.
5MENU SCREEN5-5Menu functions (Continued)High Transmit Power “HI TX POWER”❍ In the NXDN Trunking system Toggles the transmit power level.When “Auto” is set as the default: When “HI TX POWER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON (High) or OFF w(Auto). • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eWhen “Low” is set as the default: When “HI TX POWER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON (High) or OFF w(Low). • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eSee page 5-6 about [Low Transmit Power].Home CH/GID Select “HOME CHANNEL”Sets the selected channel or GID as the Home Chan-nel.Select a desired channel. (p. 2-4) qPush [MENU]. w • Opens the Menu screen. When “HOME CHANNEL” is displayed, push [P1] e(ENT). • Sets the selected channel or GID as the Home Channel.Horn Alert “HORN ALERT”Turns the Horn Alert function ON or OFF.When this function is ON, the horn alert port will be ac-tivated for a preset time period after receiving a call. When “ qHORN ALERT” is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eIndividual (NXDN) “INDIVIDUAL”Enters the Individual Call mode. When “INDIVIDUAL” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519.Push [P3](TX) to call to the selected unit ID. eIndividual + SDM (NXDN) “INDIV+SDM”Enters the Individual Call mode, and then the Short Data Message Entry mode. When “INDIV+SDM” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519.Push [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the optional DTMF microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter. Push [PTT] to send the message to the selected unit yID.Individual + Status (NXDN) “INDIV+STATUS”Enters the Individual Call mode, and then the Status Message Entry mode. When “INDIV+STATUS” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519.Push [P1](ENT). e • Enters the Status Message Selection mode. Push [UP] or [DOWN] to select a status message ethat you want to send. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the selected runit ID.LCD Brightness “LCD BRIGHT”Selects the brightness of the function display and keys backlight.Select High, Low or OFF to meet your needs.The function display and keys can be backlit for better visibility under low light conditions. When “LCD BRIGHT” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select “LOW,” “HIGH” or w“OFF.” • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. e
5MENU SCREEN5-6Menu functions (Continued)Lone Worker “LONE WORKER”Turns the Lone Worker function ON or OFF. (p. 3-5) When “LONE WORKER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eLow Transmit Power “LOW TX POWER”❍ In the Analog mode or NXDN Conventional systemToggles the transmit power between “High” and “Low,” if “High” is set as the default. When “LOW TX POWER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF w(High). • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. e❍ In the NXDN Trunking system Toggles the transmit power level.When the transmit power level is set to “Auto” as the default: When “LOW TX POWER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF w(Auto). • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eWhen the transmit power level is set to “High” as the default: When “LOW TX POWER” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF w(High). • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eSee page 5-5 about [High Transmit Power].Maintenance “MAINTENANCE”Enters the Maintenance Display mode.In the Maintenance Display mode, you can check the RSSI level of the selected channel for installation or maintenance of the system. When “MAINTENANCE” is displayed, push [P1](ENT). q • Displays the RSSI level. • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to exit. wMonitor “MONITOR”❍ In the Analog modeTurns the Monitor ON or OFF.When the Monitor is ON, the transceiver releases the CTCSS mute.❍ In the NXDN Conventional systemTurns the Monitor ON or OFF.When the Monitor is ON, the transceiver releases the RAN code mute. When “MONITOR” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eOperator Selectable Tone “OST”Turns the OST (Operator Selectable Tone) mode ON or OFF.When the OST mode is ON, the selected tone in the OST list is enabled. When “OST” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eOST List “OST LIST”Displays the OST (Operator Selectable Tone) list. When “OST LIST” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired OST tone wor turn OFF the OST tone. • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to exit. ePriority-channel Select “PRI CH SEL”Enters the Priority Channel Select mode for a Priority scan.Select a desired channel. (p. 2-4) qPush [MENU]. w • Opens the Menu screen. When “PRI CH SEL” is displayed, push [P1](ENT). e Push [UP] or [DOWN] to select “PRIORITY 1,” “PRI- rORITY 2,” “PRIORITY 1 & 2” or “NORMAL.” • Push [P0](BACK) to return to the previous screen.Push [P1](OK). t • Sets the selected channel to Priority 1, Priority 2, Priority 1 and 2 or a Normal channel.NOTE: When “PRIORITY 1 & 2” is selected, the same channel is set as both Priority 1 and Priority 2 channels.
5MENU SCREEN5-7Menu functions (Continued)Public Address “PUB ADDRESS”Turns the Public Address function ON or OFF.When this function is ON, you can make announce-ments through a PA speaker.• Transmitting is disabled while in the PA mode. When “PUB ADDRESS” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eRX Audio Equalizer “RX AUDIO EQ”This function sets the audio characteristics type to ap-ply to the received audio. When “RX AUDIO EQ” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select the option. w • Push [P0](BACK) to return to the previous screen. • FLAT: Selects the standard audio characteristics. • HIGH BOOST: Emphasizes the treble range. • LOW BOOST: Suppresses the treble range and boosts the bass range.Push [P1](EXIT) to save. eRX Auto Gain Control “RX AUTO GAIN”This function automatically adjusts the received audio volume to an appropriate level so that you can clearly hear the audio. When “RX AUTO GAIN” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select the option. w • Push [P0](BACK) to return to the previous screen. • OFF: Disables the Auto Gain Control. The received audio level is only adjusted by [VOL]. • HIGH: Enables the Auto Gain Control. The received audio level will be automatically adjusted to an appropriate constant level, according to the [VOL] setting. However, the background noise will be boosted, and howling may oc-cur, depending on your operating environ-ment. • LOW: Enables the Auto Gain Control. The received audio level will be automatically adjusted to an appropriate constant level, according to the [VOL] setting. However, the adjust-able gain is smaller than the “HIGH” setting. Therefore, background noise boosting will also be smaller, and howling may not occur.Push [P1](EXIT) to save. eRX Low Cut “RX LOW CUT”While receiving a digital signal, this function cuts the frequency components at 300 Hz or below. When “RX LOW CUT” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to save. eScan “SCAN”Starts or stops a scan. When “SCAN” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK). e • A scan starts when “ON” is selected in step w. • A scan stops when “OFF” is selected in step w.Scan Delete/Add “SCAN DEL/ADD”Sets or cancels the selected channel or GID as the scan target.Select a desired channel. (p. 2-4) qPush [MENU]. w • Opens the Menu screen. When “SCAN DEL/ADD” is displayed, push [P1] e(ENT). Push [UP] or [DOWN] to select “DELETE” or “ADD.” r • Push [P0](BACK) to return to the previous screen.Push [P1](OK). t • The selected channel is canceled as a scan target when “DELETE” is selected in step r. • The selected channel is set as a scan target when “ADD” is selected in step r.Scrambler/Encryption “SCRAM/ENCRYP”❍ In the Analog modeTurns the Scrambler function ON or OFF.❍ In the NXDN Conventional system or the NXDN Trunking systemTurns the Encryption function ON or OFF. When “SCRAM/ENCRYP” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. e
5MENU SCREEN5-8Menu functions (Continued)Scrambler/Encryption Code “SCRAM CODE”❍ In the Analog modeEnters the Scrambler Code Selection mode.❍ In the NXDN Conventional system or the NXDN Trunking systemEnters the Encryption Key Selection mode. When “SCRAM CODE” is displayed, push [P1] q(ENT). • The Scrambler or the Encryption function automatically turns ON. Push [UP] or [DOWN] to select a desired Scrambler wcode or Encryption key. • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to save. eSDM (NXDN) “SHRT MSG MOD”❍ In the NXDN Conventional system or the NXDN Trunking systemDirectly enters the Short Message mode. When “SHRT MSG MOD” is displayed, push [P1] q(ENT). • “MESSAGE?” appears. Push [UP] or [DOWN] to enter a character, and then wpush [P1](SEL) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the optional DTMF microphone. Repeat step e w until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter. Push [PTT] to send the message to the Base ID. rPush [P1](EXIT) to exit. tSend the GPS Data “SND GPS DATA”❍ In the NXDN Conventional system or the NXDN Trunking systemSends the position data that is received from the GPS receiver to a Base station. When “SND GPS DATA” is displayed, push [P1](ENT). qPush [P1](ENT) to send. wSite Lock “SITE LOCK”❍ In the NXDN Trunking systemTurns the Site Lock function ON or OFF. When “SITE LOCK” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to save. eSite Number “SITE No.”❍ In the NXDN Trunking systemDisplay the current Site number. When “SITE No.” is displayed, push [P1](ENT). ➥ • Displays the current Site number for 3 seconds, and then exits the Menu screen.Site Select “SITE”❍ In the NXDN Trunking systemEnters the Site Select mode. When “SITE” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a desired site. w • Push [P0](BACK) to return to the previous screen.Push [P1](SEL) to save. eSquelch Level “SQL LEVEL”❍ In the Analog modeEnters the Squelch Level Adjustment mode. When “SQL LEVEL” is displayed, push [P1](ENT). q Push [DOWN] to decrease the squelch level down wto 0 (loose squelch), or push [UP] to increase the squelch level up to 9 (tight squelch). • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to exit. eSquelch Off “SQL OFF”❍ In the Analog mode or the NXDN Conventional systemOpens the squelch, and releases the mute. When “SQL OFF” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](OK) to exit. eStack “STACK”Enters the Memory Stack mode. When “STACK” is displayed, push [P1](ENT). q • Push [P0](BACK) to return to the previous screen. Push [UP] or [DOWN] to select a desired message. w • Push [P0](DEL) to delete the selected message. • Push [P2](DISP) to change the display item between re-ceived ID, message contents and channel number.Push [P1](EXIT) to exit. e
5MENU SCREEN5-9Menu functions (Continued)Status (NXDN) “STATUS”Directly enters the Status Message mode. When “STATUS” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select a status message. w • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the Base ID. ePush [P1](EXIT) to exit. rTalk Around “TALK AROUND”❍ In the Analog modeTurns the talk around function ON or OFF. When “TALK AROUND” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON or OFF. wPush [P1](OK) to save. eTransceiver Password “PASSWORD”Enters the Password Entry mode.The transceiver cannot be used until you enter a cor-rect password. When “PASSWORD” is displayed, push [P1](ENT). q • Enters the Password Entry mode. Push [UP] or [DOWN] to enter a digit code, and wthen push [P1] to set. • Goes to the next digit entry position. Repeat step e w until you enter the password, and then push [P1].When using the DTMF microphone:Push the [0] to [9] digit keys on the microphone to enter the password, and then push [#]. NOTE: If “PASSWORD” does not disappear after pushing [P1], the password code you entered may be incorrect. In this case, enter the correct pass-word.TX Audio Equalizer “TX AUDIO EQ”This function sets the audio characteristics type to ap-ply to the transmit audio. When “TX AUDIO EQ” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select the option. w • Push [P0](BACK) to return to the previous screen. • FLAT: Selects the standard audio characteristics. • HIGH BOOST: Selects the audio characteristics emphasizing the treble range. • LOW BOOST: Suppresses the treble range and boosts the bass range.Push [P1](EXIT) to save. eTX Auto Gain Control “TX AUTO GAIN”This function automatically adjusts the transmit audio level to an appropriate constant level so that the called station can hear the audio clearly. When “TX AUTO GAIN” is displayed, push [P1](ENT). q Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen. • ON: Enables the Auto Gain Control. The transmit audio level will be adjusted to an appropriate constant level. • OFF: Disables the Auto Gain Control.Push [P1](EXIT) to save. eTX Noise Suppressor “TX NOISE SUP”This function enables transmitting while in the digital mode and reducing or eliminating the noise component in the background noise. When “TX NOISE SUP” is displayed, push [P1] q(ENT). Push [UP] or [DOWN] to select ON or OFF. w • Push [P0](BACK) to return to the previous screen.Push [P1](EXIT) to save. eZone Delete/Add “ZONE DEL/ADD”Sets or cancels the selected zone as a scan target.Select a desired zone. (p. 2-3) qPush [MENU]. w • Opens the Menu screen. When “ZONE DEL/ADD” is displayed, push [P1] e(ENT). Push [UP] or [DOWN] to select “DELETE” or “ADD.” r • Push [P0](BACK) to return to the previous screen.Push [P1](OK). t • The selected zone is canceled as a scan target when “DELETE” is selected in step r. • The selected zone is set as a scan target when “ADD” is selected in step r.
6-1Section 6NXDN OPERATION <COMMON>NXDN system operation ..........................................................6-2Memory Stack ..........................................................................6-3Viewing a stored message D ......................................................6-3Deleting a desired message D ....................................................6-4Deleting all stored messages D ..................................................6-4
6NXDN OPERATION <COMMON>6-2NXDN system operationNXDN is a “Common Air Interface” (CAI), the name for over-the-air methods by which transceivers and repeat-ers communicate. NXDN defines the next-generation digital protocol. The NXDN system has two operating modes, conven-tional and trunking.In an NXDN conventional system, you should manually search for a clear channel.In an NXDN trunking system, the repeater automati-cally searches for a clear channel, and sends the infor-mation to the transceivers. In addition, Type-C requires a Control Channel repeat-er.If you use an NXDN transceiver, you can transmit and receive Individual Calls, Group Calls, Status Messages, Short Messages, and so on.
6NXDN OPERATION <COMMON>6-3Memory StackThe transceiver has a Memory Stack. When the trans-ceiver receives a Status Message or a Short Message, the received content is stored in the transceiver’s Mem-ory Stack.If you turn OFF the transceiver’s power, the contents will be cleared.The stored messages are displayed using the following indication.Information IndicationMessage type Caller ID Stack “ID”Status Message “ST”Short Message “SM”Stored number Stored number “01” to “15”Display items Caller ID “ID”Message contents “MSG”Received channel or GID “CH”Viewing a stored message D When a transceiver receives data: q • Displays “DATA RCVD,” “COMPLETE,” the received mes-sage, the caller’s unit ID and GID*. *Displays only when the received call is a Group call. • “ ” blinks. Push [Stack]. w • Enters the Memory Stack mode. • Displays “STACK.” Push [UP] or [DOWN] to select a desired message. e Push [P2](DISP) to change the displayed item be- rtween received ID, message contents and channel number. STACKSM01 IDSTACK UID 0001ScrollsSTACKSM01 MSGSTACKSHORT MESSAGSTACKSM01 CHSTACK CH CH01Received IDMessage contentsChannel numberPush [P1](EXIT). t • Exits the Memory Stack mode.
6NXDN OPERATION <COMMON>6-4Memory Stack (Continued)Deleting a desired message D Push [Stack]. q • Enters the Memory Stack mode. • Displays “STACK.” Push [UP] or [DOWN] to select a desired message. wPush [P0](DEL). e • Displays “DELETE?.”Push [P1](OK). r • Deletes the selected message. • Push [P0](BACK) to return to the previous screen. • Push [R] to exit the Memory Stack mode.Deleting all stored messages D Push [Stack]. q • Enters the Memory Stack mode. • Displays “STACK.” Hold down [P0](DEL) for 1 second. w • Displays “ALL DELETE?.”Push [P1](OK). e • Deletes all messages. • Push [P0](BACK) to return to the previous screen. • Push [R] to exit the Memory Stack mode.
7-1Section 7NXDN OPERATION <TRUNKING MODE>NXDN trunking operation ........................................................7-2Selecting a GID (Group ID) .....................................................7-3Selecting a GID D ......................................................................7-3Selecting a Home GID D.............................................................7-3Directly entering a GID D ............................................................7-3Transmitting a call ...................................................................7-4Group call (Transmission Trunked) D ..........................................7-4Individual call (Transmission Trunked) D .....................................7-5Group call (Message Trunked) D ................................................7-6Individual call (Message Trunked) D ...........................................7-6Broadcast Group call D ...............................................................7-7Status call D ................................................................................7-7Short Data call D .........................................................................7-8Long Data call D .........................................................................7-8Telephone call D .........................................................................7-9Receiving a call ........................................................................7-10Group call D ................................................................................7-10Individual call D ...........................................................................7-10Broadcast Group call D ...............................................................7-11Status call D ................................................................................7-11Short Data call D .........................................................................7-12Long Data call D .........................................................................7-12Telephone call D .........................................................................7-13Forced Search ..........................................................................7-14
7NXDN OPERATION <TRUNKING MODE>7-2NXDN trunking operationWhen you select the NXDN Trunking system mode, your transceiver automatically searches for, and se-lects a clear channel.To use the NXDN Trunking system mode, your trans-ceiver must register to a Control Channel repeater.Before operating in the NXDN Trunking system mode, select the NXDN Trunking System zone. (p. 2-3)
7NXDN OPERATION <TRUNKING MODE>7-3Selecting a GID (Group ID)Selecting a GID DTo select a desired GID, do one of the following:Push [CH/GID Up] or [CH/GID Down]. ➥ Push one of the direct GID select keys, [Direct CH/ ➥GID 1] to [Direct CH/GID 5]. • You can change the GID that is selected by push-ing [Direct CH/GID 1] to [Direct CH/GID 5], as de-scribed below.Changing the Direct GID setting:Select a desired GID. q Hold down one of the [Direct CH/GID 1] to [Direct wCH/GID 5] keys for 3 seconds to set the selected GID to the Direct GID 1 to 5.Directly entering a GID DYou can select a GID by pushing [UP] or [DOWN], or the [0] to [9] digit keys on the microphone, after pushing [Channel Entry].Or, when the Channel Entry function is assigned to the keypad, you can select a GID by pushing the [0] to [9] digit keys. Push [Channel Entry] to enter the GID Entry mode. qCH ENTER MODCH No. _ _ wPush [UP] or [DOWN] to select the GID, and then push [P1](SEL). • Push [P0](BACK) to cancel the entry, and return to the screen that you selected before entering the GID Entry mode. GR 1When the GID name is not programmed, the select-ed zone and channel number are displayed.(example: “1- 1”)When using the DTMF microphone: Push the [0] to [9] digit keys to enter the GID Entry qmode.CH ENTER MODCH No. _ 1 Enter the GID number, and then push [#]. w • Push [M] to delete the entered number. • Push [M] again to cancel the entry, and return to the screen that you selected before entering the GID Entry mode. GR 1• When the GID name is not programmed, the se-lected zone and channel number are displayed. (example: “1- 1”)• When less than 9 GIDs are programmed in the zone, you can select a GID without pushing [#] in step w.Selecting a Home GID DThe Home GID is the most often-used ID, and you can preset it into the transceiver.Push [Home CH/GID]. ➥ • You can change the Home GID, as described be-low.Changing the Home GID setting:Select a desired GID. q Hold down [Home CH/GID Select] for 3 seconds to wset the selected GID to the Home GID.
7NXDN OPERATION <TRUNKING MODE>7-4Transmitting a callGroup call (Transmission Trunked) DWhen you select an NXDN Trunking System zone and a desired GID, you can transmit a Group call by simply pushing [PTT].When you set GID to “ALL,” you can call all transceiv-ers. Push [PTT] to make a Group call. ➥For your reference:When [Group + SDM (NXDN)] or [Group + Status (NXDN)] is assigned, you can also send a message along with a Group call.To send a Short Data Message along with a Group call. Push [Group + SDM (NXDN)] to enter the GID Se- qlect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired GID. wPush [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAG Push [PTT] to send the message to the selected yGID. Push [P1](EXIT) to exit. uTo send a Status Message with a Group call. Push [Group + Status (NXDN)] to enter the GID Se- qlect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired GID. wPush [P1](ENT). e • Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status rmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the message to the tselected GID. Push [P1](EXIT) to exit. y
7NXDN OPERATION <TRUNKING MODE>7-5Transmitting a call (Continued)Individual call (Transmission Trunked) DYou can call a specified station that is set to the same unit ID by using the Individual call function. Push [Individual (NXDN)] to enter the Unit ID Select qmode. • Displays “SELCALL.”SELCALL UID 0001 Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make an Individual call. e Push [P1](EXIT) to exit. rFor your reference:When [Individual + SDM (NXDN)] or [Individual + Sta-tus (NXDN)] is assigned, you can also send a mes-sage along with an Individual call.To send a Short Data Message along with an Individ-ual call. Push [Individual + SDM (NXDN)] to enter the unit ID qSelect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired unit ID. wPush [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAG Push [PTT] to send the message to the selected yunit ID. Push [P1](EXIT) to exit. uTo send a Status Message with an Individual call. Push [Individual + Status (NXDN)] to enter the unit qID Select mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired unit ID. wPush [P1](ENT). e • Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status rmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the message to the tselected unit ID. Push [P1](EXIT) to exit. y
7NXDN OPERATION <TRUNKING MODE>7-6Individual call (Message Trunked) DWhen the Trunking type is set to “Message Trunked,” and after making an Individual call, the transceiver con-tinues to be linked to the traffic channel for a preset time period.While linked, the transceivers occupy the traffic chan-nel, and you can call by simply pushing [PTT]. Push [Individual (NXDN)] to enter the Unit ID Select qmode. • Displays “SELCALL.”SELCALL UID 0001 Push [UP] or [DOWN] to select the desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make an Individual call. e Push [P1](EXIT). rGroup call (Message Trunked) DWhen the Trunking type is set to “Message Trunked,” and after making a Group call, the transceiver contin-ues to be linked to the traffic channel for a preset time period.While linked, the transceivers occupy the traffic chan-nel, and you can call by simply pushing [PTT].When you select the NXDN Trunking System zone and a desired GID, you can transmit a Group call by simply pushing [PTT].When you set GID to “ALL,” you can call all transceiv-ers. Push [PTT] to make a Group call. ➥Transmitting a call (Continued)For your reference:When [Group + SDM (NXDN)] or [Group + Status (NXDN)] is assigned, you can send a message along with a Group call. See page 7-4 for details.For your reference:When [Individual + SDM (NXDN)] or [Individual + Sta-tus (NXDN)] is assigned, you can send a message along with an Individual call. See page 7-5 for details.
7NXDN OPERATION <TRUNKING MODE>7-7Broadcast Group call DWhen you use the Broadcast Group call function, you can transmit a signal to transceivers that are set to the same Group ID. When you set GID to “ALL,” you can make the Broad-cast Group call to all transceivers. Select a desired GID. (p. 7-3) q Push [Broadcast] once or twice to select “BRDCAST wON.”BRDCAST ON Push [PTT] to make a Broadcast Group call. eStatus call DThe Status call is a simple message function to trans-mit and receive a status message. A transceiver can display the status message quickly. You cannot transmit a voice signal at the same time. Push [Status (NXDN)] to enter the Status Message qSelect mode. • Displays “STATUS.” Push [UP] or [DOWN] to select a desired status wmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the selected Status eMessage. • Displays “SEND DATA” and then “COMPLETE.”Transmitting a call (Continued)
7NXDN OPERATION <TRUNKING MODE>7-8Short Data call DYou can send a Short Data message of up to 100 char-acters.If you turn OFF the transceiver’s power, the message is cleared. Push [SDM (NXDN)] to enter the Short Data Mes- qsage Entry mode. • Displays “MESSAGE?”. MESSAGE? Push [UP] or [DOWN] to enter a character, and then wpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step e w until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAGPush [PTT] to send. e • Displays “SEND DATA” and then “COMPLETE.” Push [P1](EXIT) to exit. rIf you exit from the Short Data Message Entry mode, and then you want to send the message again, do the following steps. Push [SDM (NXDN)] to enter the Short Data Mes- qsage Entry mode. • Displays the entered message. • Displays the last part of the message if the message is over 12 characters.HORT MESSAGEPush [PTT] to send. w • Displays “SEND DATA” and then “COMPLETE.” Push [P1](EXIT) to exit. eTransmitting a call (Continued)Long Data call DYou can send a Long Data message of up to 4,096 characters only by using an external device, such as a PC. You cannot send a Long Data message by pushing [PTT].
7NXDN OPERATION <TRUNKING MODE>7-9Telephone call DIf you use the Telephone Call function, you can com-municate with a telephone through the telephone lines (PSTN, PABX, and so on).You can call from a transceiver to a telephone, or call from a telephone to a transceiver.Push [Autodial]. q • The rst entry in the Autodial list appears. Push [UP] or [DOWN] to select your desired tele- wphone number. Push [P3](TX) or [PTT] to start a Telephone call e • Displays “CALLING.” • Displays “PHONE CALL” when the transceiver connects to the telephone line. Displays “INVALID” when the transceiver cannot connect to the line.Hold down [PTT] to talk. r The telephone line will disconnect when you push t[R] or microphone’s [M], or when the microphone is on-hook (depending on the presetting).Transmitting a call (Continued)
7NXDN OPERATION <TRUNKING MODE>7-10Receiving a callIndividual call DWhen you receive an Individual call that includes your unit ID, your transceiver informs you of the call by sounding beeps and blinking “ ” on the function dis-play. In addition, you can easily call back to the calling station. When you receive an Individual call that includes qyour unit ID: • Beeps sound. • Displays the caller’s unit ID.* * Alternately displays the caller’s unit ID and “INCOMING,” when you receive a “Message Trunked” type call, and the Automatic Response function is OFF. • “ ” blinks for about 10 seconds.UID 0001 To call back to the caller station, push [PTT] while w“ ” is blinking.Group call DWhen you receive a Group call that includes a matched GID, your transceiver informs you of the call by sound-ing beeps and blinking “ ” on the function display. In addition, you can easily call back to the calling station. When you receive a Group call that includes a qmatched GID: • Beeps sound. • Displays the caller’s unit ID and GID. • “ ” blinks for about 10 seconds.UID 0001GID 0002 To call back to the caller station, push [PTT] while w“” is blinking.
7NXDN OPERATION <TRUNKING MODE>7-11Broadcast Group call DWhen a Broadcast Group Call is made, the transceiv-ers with the same selected Group ID will receive the call.You cannot transmit a reply to the calling transceiver.When your transceiver receives a Broadcast Group Call, beeps sound.While your transceiver is receiving the call, the musical tone icon blinks on the function display.Receiving a call (Continued)Status call DWhen you receive a Status call, your transceiver dis-plays a received status message on the function display. The received message is stored in the Memory Stack, and you can view the message contents in the memory. (p. 6-3) When you receive a Status call: ➥ • Beeps sound. • Displays “DATA RCVD,” “COMPLETE,” the received mes-sage, the caller’s unit ID and GID*. *Displayed only when the received call is a Group call. • “ ” blinks on the function display. The message is stored in the Memory Stack.UID 0001GID 0002COMPLETESTATUS 001
7NXDN OPERATION <TRUNKING MODE>7-12Short Data call DWhen you receive a Short Data message, your trans-ceiver displays the message on the function display. The message is stored in the Memory Stack, and you can view the message in the memory. (p. 6-3) When you receive a Short Data message: ➥ • Beeps sound. • Displays “DATA RCVD,” “COMPLETE,” the received mes-sage, the caller’s unit ID and GID*. *Displayed only when the received call is the Group call. • “ ” blinks on the function display. The message is stored in the Memory Stack.Long Data call DYou can receive a Long Data message of up to 4,096 characters. The message can be output to a PC or ex-ternal device from your transceiver.Receiving a call (Continued)UID 0001GID 0002COMPLETESHORT MESSAGDATA RCVDScrolls when the re-ceived message is over 12 characters.
7NXDN OPERATION <TRUNKING MODE>7-13Telephone call DWhen you receive a call from a telephone, you can com-municate with it through the telephone lines (PSTN, PABX, and so on).When a telephone calls your transceiver, the transceiv-er sounds beeps, and then “PHONE” is displayed on the function display.Hold down [PTT] to talk to the telephone.Receiving a call (Continued)
7NXDN OPERATION <TRUNKING MODE>7-14Forced SearchIf you use the Forced Search function, the transceiver searches for other Control channels using the following hunt sequences.Hunt sequence ExplanationPreferential Hunt SequenceThe transceiver searches for a Control channel that is set as the Preferential Hunt Control channel.The transceiver selects this Control channel with a high priority.Normal Hunt Sequence The transceiver searches for a Control channel that is set as the Normal Hunt Control channel.System Add Channel Sequence The transceiver searches for up to 8 Control channels that are added by the system.Site Hunt Sequence The transceiver searches for a Control channel that is set as the Site Hunt Control channel in each site.Comprehensive Hunt Sequence The transceiver searches for a Control channel that is set in the network frequency table. Hold down [Forced Search Function] for 2 seconds qto turn ON the Forced Search Function. • Displays the current site number. The transceiver starts to search for a Control chan- wnel signal. • Displays “SEARCHING.” When the transceiver finds and registers to a control echannel, the normal screen is displayed on the func-tion display.
8-1Section 8NXDN OPERATION <CONVENTIONAL MODE>NXDN Conventional operation ...............................................8-2Transmitting a call ...................................................................8-3Group call D ................................................................................8-3Individual call D ...........................................................................8-4 Individual Call Acknowledge Request call D ...............................8-4Status call D ................................................................................8-5Short Data call D .........................................................................8-5Long Data call D .........................................................................8-5Receiving a call ........................................................................8-6Group call D ................................................................................8-6Individual call D ...........................................................................8-6 Individual Call Acknowledge Request call D ...............................8-7Status call D ................................................................................8-7Short Data call D .........................................................................8-8Long Data Call D.........................................................................8-8Mixed Mode ..............................................................................8-9
8NXDN OPERATION <CONVENTIONAL MODE>8-2NXDN Conventional operationWhen you select the NXDN Conventional system mode, you must manually search for and select a clear channel.The system setup is easier than the Trunking mode.
8NXDN OPERATION <CONVENTIONAL MODE>8-3Transmitting a callFor your reference:When [Group + SDM (NXDN)] or [Group + Status (NXDN)] is assigned, you can send a message along with a Group call.To send a Short Data Message with a Group call. Push [Group + SDM (NXDN)] to enter the GID Se- qlect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired GID. wPush [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAG Push [PTT] to send the message to the selected yGID. Push [P1](EXIT) to exit. uTo send a Status Message with a Group call. Push [Group + Status (NXDN)] to enter the GID Se- qlect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired GID. wPush [P1](ENT). e • Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status rmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the message to the tselected GID. Push [P1](EXIT) to exit. yGroup call DWhen you select the NXDN Conventional System zone, you can make a Group call by using the Group Call function.Set GID to “ALL,” to call all transceivers. Push [Group (NXDN)] to enter the GID Select mode. q • Displays “SELCALL.”SELCALL GID 0001 Push [P2]( wΩ) or [P3](≈) to select the desired GID. Push [PTT] to make a Group call. e Push [P1](EXIT). r
8NXDN OPERATION <CONVENTIONAL MODE>8-4Transmitting a call (Continued)Individual call DYou can call a specified station that is set to the same unit ID by using the Individual call function. Push [Individual (NXDN)] to enter the Unit ID Select qmode. • Displays “SELCALL.”SELCALL UID 0001 Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make the Individual call. e Push [P1](EXIT). rFor your reference:When [Individual + SDM (NXDN)] or [Individual + Sta-tus (NXDN)] is assigned, you can send a message along with an Individual call.To send a Short Data Message with an Individual call. Push [Individual + SDM (NXDN)] to enter the unit ID qSelect mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired unit ID. wPush [P1](ENT). e • Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then rpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step t r until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAG Push [PTT] to send the message to the selected yunit ID. Push [P1](EXIT) to exit. uTo send a Status Message with an Individual call. Push [Individual + Status (NXDN)] to enter the unit qID Select mode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired unit ID. wPush [P1](ENT). e • Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status rmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the message to the tselected unit ID. Push [P1](EXIT) to exit. y Individual Call Acknowledge Request call DWhen the Individual Call Acknowledge Request func-tion is set, you can transmit an acknowledgement re-quest signal with the Individual call.Therefore, you can confirm whether the transceiver is located in the communication range or not. Push [Individual (NXDN)] to enter the Unit ID Select qmode. • Displays “SELCALL.” Push [UP] or [DOWN] to select a desired unit ID. w • If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make the Individual call ewith an acknowledgement request signal. • Displays “CALLING,” and then after receiving an acknowl-edgement, displays “HOLDING.” When the called station calls back, the transceiver rdisplays the called station’s unit ID. • Displays “NO REPLY” and sounds error beeps when your transceiver does not receive an acknowledgement within the preset time period.
8NXDN OPERATION <CONVENTIONAL MODE>8-5Transmitting a call (Continued)Status call DThe status call is a simple message function to transmit and receive a status message. A transceiver can dis-play the status message quickly. You cannot transmit a voice signal at the same time. Push [Status (NXDN)] to enter the Status Message qSelect mode. • Displays “STATUS.” Push [UP] or [DOWN] to select a desired status wmessage. • If you want to directly enter a status message, push [P2](MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. • You can use the 10-keypad keys on the microphone.STATUSSTATUS 001 Push [P3](TX) or [PTT] to send the selected Status eMessage. • Displays “SEND DATA” and then “COMPLETE.”Short Data call DYou can send a Short Data message of up to 100 char-acters.If you turn OFF the transceiver’s power, the message is cleared. Push [SDM (NXDN)] to enter the Short Data Mes- qsage Entry mode. • Displays “MESSAGE?”. MESSAGE? Push [UP] or [DOWN] to enter a character, and then wpush [P1](SET) to set. • Goes to the next character entry position. • You can use the 10-keypad keys on the microphone. Repeat step e w until you enter a message of up to 100 characters. • Push [P0](DEL) to delete a character. • Push [P2](Ω) or [P3](≈) left or right to select a charac-ter.SHORT MESSAGPush [PTT] to send. r • Displays “SEND DATA” and then “COMPLETE.” Push [P1](EXIT) to exit. tIf you exit from the Short Data Message Entry mode, and then you want to transmit the message again, do the following steps. Push [SDM (NXDN)] to enter the Short Data Mes- qsage Entry mode. • Displays the entered message. • Displays the last part of the message if the message is over 12 characters.HORT MESSAGEPush [PTT] to send. w • Displays “SEND DATA” and then “COMPLETE.” Push [P1](EXIT) to exit. eLong Data call DYou can send a Long Data message of up to 4,096 characters only by using an external device, such as a PC. You cannot send a message by pushing [PTT].
8NXDN OPERATION <CONVENTIONAL MODE>8-6Receiving a callIndividual call DWhen you receive an Individual call that includes your unit ID, your transceiver informs you the calling by sounding beeps and blinking “ ” on the function dis-play. In addition, you can easily call back to the calling station. When you receive an Individual call that includes qyour unit ID: • Beeps sound. • Displays the caller’s unit ID. • “ ” blinks for about 10 seconds.UID 0001 To call back to the caller station, push [PTT] while w“” is blinking.Group call DWhen you receive a Group call that includes a matched GID, your transceiver informs you the calling by sound-ing beeps and blinking “ ” on the function display. In addition, you can easily call back to the calling station. When you receive a Group call that includes a qmatched GID: • Beeps sound. • Displays the caller’s unit ID and GID. • “ ” blinks for about 10 seconds.UID 0001GID 0002 To call back to the caller station, push [PTT] while w“” is blinking.
8NXDN OPERATION <CONVENTIONAL MODE>8-7Receiving a call (Continued) Individual Call Acknowledge Request call DWhen you receive an Individual Call with an acknowl-edgement request which includes your own Individual ID, your transceiver automatically transmits a acknowl-edgement signal, and informs you the calling by beep sounds and bell mark blinks on the function display. In addition, you can easily call back to the calling trans-ceiver. When you receive an Individual call with an acknowl- qedgement request signal that includes your unit ID: • Beeps sound. • Alternately displays the caller’s unit ID and “INCOMING.” • “ ” blinks for about 30 seconds. To call back to the caller station, push [PTT] while w“ ” is blinking.Status call DWhen you receive a Status call, your transceiver dis-plays a received status message on the function display. The received message is stored in the Memory Stack, and you can view the message contents in the memory. (p. 6-3) When you receive a Status call: ➥ • Beeps sound. • Displays “DATA RCVD,” “COMPLETE,” the received mes-sage, the caller’s unit ID and GID*. *Displayed only when the received call is the Group call. • “ ” blinks on the function display. The message is stored in the Memory Stack. UID 0001GID 0002COMPLETESTATUS 001
8NXDN OPERATION <CONVENTIONAL MODE>8-8Long Data Call DYou can receive a Long Data message of up to 4,096 characters. The message can be output to a PC or ex-ternal device from your transceiver.Receiving a call (Continued)Short Data call DWhen you receive a Short Data message, your trans-ceiver displays the message on the function display. The message is also stored in the Memory Stack, and you can view the message in the memory. (p. 6-3) When you receive a Short Data message: ➥ • Beeps sound. • Displays “DATA RCVD,” “COMPLETE,” the received mes-sage, the caller’s unit ID and GID*. *Displayed only when the received call is the Group call. • “ ” blinks on the function display. The message is stored in the Memory Stack.UID 0001GID 0002COMPLETESHORT MESSAGDATA RCVDScrolls when the re-ceived message is over 12 characters.
8NXDN OPERATION <CONVENTIONAL MODE>8-9Mixed ModeIf you set your transceiver to the Mixed mode, you can receive both digital and analog signals. You can use a digital transceiver on analog channels, therefore you can easy switch from an analog system to a digital sys-tem.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanA-7148-3EX© 2014 Icom Inc.

Navigation menu