ICOM orporated 366400 VHF Digital Transceiver User Manual IC F5360D F6360D Operating Instructions

ICOM Incorporated VHF Digital Transceiver IC F5360D F6360D Operating Instructions

User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2326887
Application ID	Twbb1eDTxmAJdaq09VIzKg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	233.81kB (2922588 bits)
Date Submitted	2014-07-16 00:00:00
Date Available	2014-09-01 00:00:00
Creation Date	2017-10-22 00:05:05
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-22 00:05:05
Document Title	IC-F5360D/F6360D Operating Instructions
Document Creator	Adobe InDesign CS3_J (5.0.4)
Document Author:	Icom Inc.

OPERATING INSTRUCTIONS
VHF DIGITAL TRANSCEIVERS
iF5360D
INTRODUCTION
PANEL DESCRIPTION
BASIC OPERATION
ADVANCED OPERATION
SCAN OPERATION
MENU SCREEN
NXDN OPERATION 
NXDN OPERATION 
NXDN OPERATION 
UHF DIGITAL TRANSCEIVERS
iF6360D
INTRODUCTION
FOREWORD
Thank you for purchasing this Icom transceiver.
The IDAS™ NXDN™ system operation is built into your
IC-F5360D VHF DIGITAL TRANSCEIVERS and IC-F6360D
UHF DIGITAL TRANSCEIVERS.
IMPORTANT
FIRST, CAREFULLY READ INSTRUCTIONS
q PRECAUTIONS and w INSTRUCTIONS that are
provided with the transceiver.
SAVE THIS OPERATING INSTRUCTIONS—
This operating instructions contain additional important
operating instructions for the IC-F5360D VHF DIGITAL
TRANSCEIVERS and IC-F6360D UHF DIGITAL TRANSCEIVERS.
NOTE
The display contents, and the hold down time period of
some keys, may vary from the description in this manual, depending on the transceiver’s presetting.
Icom, Icom Inc. and the Icom logo are registered trademarks
of Icom Incorporated (Japan) in Japan, the United States,
the United Kingdom, Germany, France, Spain, Russia and/
or other countries.
IDAS is trademark of Icom Incorporated (Japan).
NXDN is a trademark of Icom Incorporated and JVC KENWOOD Corporation.
All other products or brands are registered trademarks or
trademarks of their respective holders.
Section 1
PANEL DESCRIPTION
Front, top and side panels ......................................................1-2
D Microphone..............................................................................1-2
Function display ......................................................................1-3
Programmable function keys .................................................1-4
1-1
1
PANEL DESCRIPTION
Front, top and side panels
q LED INDICATOR w FUNCTION DISPLAY
e DEALER PROGRAMMABLE KEYS
[UP], [DOWN]
u AF VOLUME
CONTROL
KNOB [VOL]
SPEAKER
y MICROPHONE
CONNECTOR
t DEALER-PROGRAMMABLE KEYS
[R], [P0], [P1], [P2], [P3]
q LED INDICATOR
➥ Lights red while transmitting.
➥ Lights green while receiving a signal, or when the
squelch is open.
r POWER KEY [ ]
D Microphone
The supplied or optional microphone has a PTT switch
and a hanger hook.
•฀฀The฀following฀functions฀are฀available฀when฀the฀microphone is on or off hook (depending on the presetting):
- Pauses scan when it is off-hook.
- Switches to the ‘Inaudible’ mode (mute mode) when
it is on-hook.
- Switches to the ‘Audible’ mode (unmute mode)
when it is off-hook.
w FUNCTION DISPLAY (p. 1-3)
฀ D
฀ isplays a variety of information.
e DEALER-PROGRAMMABLE KEYS
[UP] and [DOWN]
฀ D
฀ esired functions can be preset.
(p. 1-5)
r POWER KEY [ ]
฀ P
฀ ush and hold for 1 second to turn the power ON
and OFF.
t DEALER-PROGRAMMABLE KEYS
[R], [P0], [P1], [P2], [P3]
฀ D
฀ esired functions can be preset.
(p. 1-5)
y MICROPHONE CONNECTOR
฀ C
฀ onnect the supplied or optional microphone.
NEVER connect non-specified microphones. The
pin assignments may be different and the transceiver may be damaged.
u AF VOLUME CONTROL KNOB [VOL]
฀ Rotate to adjust the audio output level.
1-2
1
PANEL DESCRIPTION
Function display
q w e r t
o !0
IC-F5360D
!1
!2
!3
!4
!5 !6 !7 !8
q SIGNAL STRENGTH INDICATOR
Displays the relative receive signal strength.
o HORN ALERT ICON
฀ Displayed when the Horn Alert function is ON.
w LOW OUTPUT POWER ICON
฀ Displayed when low output power is selected.
!0 PUBLIC ADDRESS ICON
฀ Displayed when the Public Address function is ON.
e AUDIBLE ICON
②拡大200%
③拡大150%
Displayed when
the channel is in the ‘audible’ (unmute) mode.
!1 ALPHANUMERIC READOUT
Displays the operating channel number, channel
name, menu contents, DTMF code, and so on.
①縦横比を52×19にする。
฀ •฀฀The฀ display฀ mode฀ automatically฀ switches฀ between฀ one฀
line and two lines.
r SCRAMBLER ICON
Displayed when the Voice Scrambler function is ON.
!2 KEY ICONS
฀ Display the assigned function of the [P0], [P1], [P2]
and [P3] dealer assignable keys.
t SCAN ICON
Displayed while scanning.
y MESSAGE ICON
➥ Displayed when a received message (Short Data
Message or Status Message) is stored in the
memory stack.
➥ Blinks when an unread message is in the memory
stack.
!3 SCAN TARGET ZONE ICON
Displayed when the scan target zone is selected.
!4 PA SPEAKER ICON
Displayed when the External speaker function is ON.
When the External speaker function is ON, the PA
speaker that is connected to the D-Sub 15-pin will
activate.
u BELL ICON
฀ B
฀ links when a matched signal is received, depending on the presetting.
!5 AUX A ICON
Displayed when the AUX A port is activate.
i GPS ICON
฀ Displayed when position data is received.
!6 AUX B ICON
Displayed when the AUX B port is activate.
!7 SCAN TARGET CHANNEL ICON
Displayed when the scan target channel is selected.
!8 OPERATOR SELECTABLE TONE ICON
Displayed when the OST (Operator Selectable Tone)
function is ON.
1-3
1
PANEL DESCRIPTION
Programmable function keys
The programmable key functions can be assigned to
the following keys:
[R], [P0], [P1], [P2], [P3], [UP], [DOWN] and to the keypad keys of the optional DTMF microphone.
[UP], [DOWN]
[R], [P0], [P1], [P2], [P3]
1-4
1
PANEL DESCRIPTION
Programmable function keys (Continued)
•฀฀For฀[R], [P0], [P1], [P2], [P3], [UP] and [DOWN]
The key names that are in quotation marks in the following explanations are displayed on the Function Display, and indicate the assigned function of [P0], [P1],
[P2] and [P3].
CH/GID Down “CH D”
Selects the next or previous channel or GID number.
None
No function
CH/GID Recall “CHRC”
❍ In the Analog mode or
NXDN Conventional system
Selects the last used channel during a scan.
Autodial “ADAL” (p. 3-2)
Opens the DTMF Autodial code selection screen.
❍ In the NXDN Trunking system
Selects the last called GID during a scan.
Autodial Programming “ADPG” (p. 3-3)
Enters the DTMF code programming mode.
CH/GID Up “CH U”
Selects the next or previous channel or GID number.
AUX A “AUXA”
Turns the AUX A port ON or OFF.
Channel Entry “CHEN” (p. 2-4)
Enters the Channel Entry mode.
AUX B “AUXB”
Turns the AUX B port ON or OFF.
CW Message “CWMS”
Sends a preset CW Message on a ‘very narrow’ channel.
You can use this function when a CW message is preset.
Broadcast “BCST”
Toggles between Broadcast Call and Conference Call.
This key can also be used to make a Broadcast Group
Call.
Direct CH/GID 1 “DR 1” (pp. 2-4, 7-3)
Selects the channel or GID that is set to Direct CH/
GID 1.
Call 1 “CAL1”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 1.
Direct CH/GID 2 “DR 2” (pp. 2-4, 7-3)
Selects the channel or GID that is set to the Direct CH/
GID 2.
Call 2 “CAL2”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 2.
Direct CH/GID 3 “DR 3” (pp. 2-4, 7-3)
Selects the channel or GID that is set to Direct CH/
GID 3.
Call 3 “CAL3”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 3.
Direct CH/GID 4 “DR 4” (pp. 2-4, 7-3)
Selects the channel or GID that is set to Direct CH/
GID 4.
Call 4 “CAL4”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 4.
Direct CH/GID 5 “DR 5” (pp. 2-4, 7-3)
Selects the channel or GID that is set to Direct CH/
GID 5.
Call 5 “CAL5”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 5.
Direct CH/GID 1 Select
This function is for the hold down operation of [Direct
CH/GID 1].
Sets the selected channel or GID to Direct CH/GID 1.
Call 6 “CAL6”
Sends the NXDN Status, NXDN Individual or the DTMF
code that is set to Call 6.
1-5
1
PANEL DESCRIPTION
Programmable function keys
•฀For฀[R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
Direct CH/GID 2 Select
This function is for the hold down operation of [Direct
CH/GID 2].
Sets the selected channel or GID to Direct CH/GID 2.
Function “FUNC”
Activates a secondary function that is assigned to a
key.
This function cannot be assigned as a secondary function.
Direct CH/GID 3 Select
This function is for the hold down operation of [Direct
CH/GID 3].
Sets the selected channel or GID to Direct CH/GID 3.
GPS Position Display “GPSP”
Enters the GPS Position Display mode.
In the GPS Position Display mode, you can check your
latitude and longitude position.
Direct CH/GID 4 Select
This function is for the hold down operation of [Direct
CH/GID 4].
Sets the selected channel or GID to Direct CH/GID 4.
Group ID/Channel Entry “GIDE” (pp. 2-4, 7-3)
❍ In the Analog mode or
NXDN Conventional system
Enters the Channel Entry mode.
Direct CH/GID 5 Select
This function is for the hold down operation of [Direct
CH/GID 5].
Sets the selected channel or GID to Direct CH/GID 5.
❍ In the NXDN Trunking system
Enters the GID Entry mode.
Group (NXDN) “GRP” (pp. 7-4, 8-3)
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode.
In the NXDN Conventional system, this function is used
for Group Call by recalling GID list.
In the NXDN Trunking system, the GID List is displayed,
but the transceiver cannot make a call.
Display Format “DISP”
❍ In the Analog mode or
NXDN Conventional system
Toggles the display format between the channel name
and the zone and channel number.
❍ In the NXDN Trunking system
Toggles the display format between the GID name and
the GID number.
Group + SDM (NXDN) “GSMS”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode.
If you push [P1](ENT) while in the Group Call mode,
the transceiver enters the Short Data Message Entry
mode. See page 7-4 or 8-3 for details.
Emergency (p. 3-5)
This function can be assigned only for [R].
Enters the Emergency mode.
External Speaker “EXSP”
Turns the External speaker function ON or OFF.
When the External speaker function is ON, the PA
speaker that is connected to the D-Sub 15-pin will be
activated.
Group + Status (NXDN) “GSTA”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode.
If you push [P1](ENT) while in the Group Call mode,
the transceiver enters the Status Message Entry mode.
See page 7-4 or 8-3 for details.
Fixed Volume “FIXV”
Toggles the tone level between “High” and “Low,” or
turns OFF the tone.
Forced Search “FORS”
Displays the site number of the current site for 2 seconds.
High Transmit Power “HIPW”
❍ In the NXDN Trunking system
➥ Toggles the transmit power level between “High” and
“Auto,” if “Auto” is set as the default.
➥ Toggles the transmit power level between “High” and
“Low,” if “Low” is set as the default.
Forced Search Function
This function is for the hold down operation of [Forced
Search].
Activates a Control Channel Hunt.
1-6
1
PANEL DESCRIPTION
Programmable function keys
•฀For฀[R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
Home CH/GID “HOME” (pp. 2-4, 7-3)
❍ In the Analog mode or
NXDN Conventional system
Selects the Home Channel.
Low Transmit Power “LOPW”
❍ In the Analog mode or
NXDN Conventional system
Toggles the transmit power between “High” and “Low,” if
“High” is set as the default.
❍ In the NXDN Trunking system
Selects the Home GID.
❍ In the NXDN Trunking system
➥ Toggles the transmit power level between “Low” and
“Auto,” if “Auto” is set as the default.
➥ Toggles the transmit power level between “High” and
“Low,” if “High” is set as the default.
Home CH/GID Select (pp. 2-4, 7-3)
This function is for the hold down operation of [Home
CH/GID].
❍ In the Analog mode or
NXDN Conventional system
Sets the selected channel as the Home Channel.
Maintenance “MANT”
Enters the Maintenance Display mode.
❍ In the NXDN Trunking system
Sets the selected GID as the Home GID.
Menu “MENU” (p. 5-2)
Displays the Menu screen.
Horn Alert “HORN”
Turns the Horn Alert function ON or OFF.
When this function is ON, the horn alert port will be activated for a preset time period after receiving a call.
Monitor “MONI”
❍ In the Analog mode
Turns the Monitor ON or OFF.
When the Monitor is ON, the transceiver releases the
CTCSS or DTCS mute.
Individual (NXDN) “INDV” (pp. 7-5, 7-6, 8-4)
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Individual Call mode.
❍ In the NXDN Conventional system
Turns the Monitor ON or OFF.
When the Monitor is ON, the transceiver releases the
RAN code mute.
Individual + SDM (NXDN) “ISMS”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Individual Call mode.
If you push [P1](ENT) while in the Individual Call mode,
the transceiver enters the Short Data Message Entry
mode. See page 7-5 or 8-4 for details.
Monitor Momentary “MONI”
❍ In the Analog mode
While holding down, the transceiver releases the CTCSS mute.
❍ In the NXDN Conventional system
While holding down, the transceiver releases the RAN
code mute.
Individual + Status (NXDN) “ISTA”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Individual Call mode.
If you push [P1](ENT) while in the Individual Call mode,
the transceiver enters the Status Message Entry mode.
See page 7-5 or 8-4 for details.
Operator Selectable Tone “OST”
Turns the OST (Operator Selectable Tone) mode ON
or OFF.
When the OST mode is ON, the selected tone in the
OST list is enabled.
LCD Brightness “BRIT”
Selects the brightness of the function display and keys
backlight. Select High, Low or OFF to meet your needs.
The function display and keys can be backlit for better
visibility under low light conditions.
OST List
This function is for the hold down operation of [Operator Selectable Tone].
Displays the OST (Operator Selectable Tone) list.
Priority-channel Select “PRIO”
Enters the Priority channel Select mode for a Priority
scan.
Lone Worker “LONE” (p. 3-5)
Turns the Lone Worker function ON or OFF.
1-7
1
PANEL DESCRIPTION
Programmable function keys
•฀For฀[R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued)
Public Address “PUBA”
Turns the Public Address function ON or OFF.
When this function is ON, you can make announcement through a PA speaker.
•฀Transmitting฀is฀disabled฀while฀in฀the฀PA฀mode.
Site Select
This function is for the hold down operation of [Site
Lock].
❍ In the NXDN Trunking system
Enters the Site Select mode.
If the site name is not entered, [Site Select] does not
function.
Scan “SCAN”
Starts or stops a scan.
Site Up “SITU”
❍ In the NXDN Trunking system
Selects the next site number.
If the site name is not entered, [Site Up] does not function.
Scan Delete/Add “SCNE”
Sets or cancels the selected channel or GID as a scan
target.
Scrambler/Encryption “SCRM”
❍ In the Analog mode
Turns the Scrambler function ON or OFF.
Squelch Level “SQLL”
❍ In the Analog mode
Enters the Squelch Level Adjustment mode.
❍ In the NXDN Conventional system or
the NXDN Trunking system
Turns the Encryption function ON or OFF.
Squelch Off “SQLO”
❍ In the Analog mode or
NXDN Conventional system
Opens the squelch, and releases the mute.
Scrambler/Encryption Code
This function is for the hold down operation of [Scrambler/Encryption].
❍ In the Analog mode
Enters the Scrambler Code mode.
Squelch Off Momentary “SQLM”
❍ In the Analog mode or
NXDN Conventional system
While holding down, opens the squelch, and releases
the mute.
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Encryption Code mode.
Stack “STAK” (p. 6-3)
Enters the Memory Stack mode.
SDM (NXDN) “SMSG”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Directly enters the Short Message mode.
Push [PTT] to send a Short Message to a Base ID.
Status (NXDN) “STAT”
Enters the Status Message mode.
Push [PTT] to send a Status to a Base ID.
Talk Around “TLKA”
Turns the Talk around function ON or OFF.
Send the GPS data “GPSD”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Sends the position data that is received from the GPS
receiver to a Base station.
•฀฀The฀Talk฀around฀function฀equalizes฀the฀transmit฀frequency฀
to the receive frequency for transceiver-to-transceiver communication.
Transceiver Password “PSWD” (p. 2-2)
Enters the password entry mode.
The transceiver cannot be used until you enter a correct password.
Site Down “SIDN”
❍ In the NXDN Trunking system
Selects the previous site number.
If the site name is not entered, [Site Down] does not
function.
Zone Delete/Add “ZODE”
Sets or cancels the selected zone as a scan target.
Site Lock “SILK”
❍ In the NXDN Trunking system
Turns the Site Lock function ON or OFF.
Zone Down “ZNDN”
Selects the previous zone number.
Zone Up “ZNUP”
Selects the next zone number.
1-8
1
PANEL DESCRIPTION
Programmable function keys (Continued)
•฀For฀Keypad฀Operation฀(Microphone)
Channel Entry (p. 2-4)
Enters the channel number.
Individual + Status (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Individual Call mode, and selects the unit ID
to transmit an Individual Call to.
If you push [P1](ENT) while in the Individual Call mode,
the transceiver enters the Status Message mode.
Group ID/Channel Entry (pp. 2-4, 7-3)
❍ In the Analog mode
❍ In the NXDN Conventional system
Enters the channel number.
❍ In the NXDN Trunking system
Enters the GID.
Individual + SDM (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Individual Call mode, and selects the unit ID
to transmit an Individual Call to.
If you push [P1](ENT) while in the Individual Call mode,
the transceiver enters the Short Data Message mode.
OST (Operator Selectable Tone)
➥ Hold down [1] to [9] to select a tone that is preset in
the OST list.
➥ Hold down [0] to turn OFF the OST tone.
➥ Hold down [M] to turn OFF the OST mode.
฀ •฀฀When฀the฀OST฀mode฀is฀OFF,฀the฀selected฀channel’s฀preset tone is used.
Group (NXDN)
❍ In the NXDN Conventional system
Enters the Group Call mode, and selects the GID to
send a Group Call to.
➥ Hold down [#], and then push the [0] to [9] digit keys
to enter the OST List number 1 to 40 to select a preset tone.
❍ In the NXDN Trunking system
Displays the GID List, but the transceiver cannot make
a call.
Autodial
Selects the DTMF Code that is preset in the Autodial
List.
After selecting, push [PTT] to send.
Group + Status (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Group Call mode, and selects the GID to
transmit a Group Call to.
If you push [P1](ENT) while in the Group Call mode, the
transceiver enters the Status Message mode.
Keypad Auto PTT
Transmits DTMF tones.
This function is enabled only when Manual Dialing is
enabled.
Status (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Status Message mode, and selects the Status number.
Group + SDM (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Group Call mode, and selects the GID to
transmit a Group Call to.
If you push [P1](ENT) while in the Group Call mode, the
transceiver enters the Short Data Message mode.
SDM (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enter an SDM message.
Individual (NXDN)
❍ In the NXDN Conventional system
❍ In the NXDN Trunking system
Enters the Individual Call mode, and selects the unit ID
to send an Individual Call to.
1-9
Section 2
BASIC OPERATION
Turning power ON....................................................................2-2
D Adjusting the audio level..........................................................2-2
D Inputting the password ............................................................2-2
Selecting a zone ......................................................................2-3
D Selecting a zone ......................................................................2-3
Selecting a channel .................................................................2-4
D Selecting a channel .................................................................2-4
D Selecting a Home channel ......................................................2-4
D Directly entering a channel ......................................................2-4
Receiving..................................................................................2-5
D Setting the squelch level..........................................................2-5
Transmitting .............................................................................2-6
D Transmitting notes ...................................................................2-6
2-1
2
BASIC OPERATION
Turning power ON
➥ Hold down [ ] for 1 second to turn ON the power.
D Adjusting the audio level
➥ When receiving a call, rotate [VOL] to adjust the audio output volume level.
[ ]
[VOL]
D Inputting the password
If the transceiver is preset for a start up password, enter the digit codes.
q While in the Password Entry mode, “PASSWORD”
is displayed.
w Push [UP] or [DOWN] to enter a digit code, and then
push [P1] to set.
฀ •฀Goes฀to฀the฀next฀digit฀entry฀position.
e Repeat step w until you enter the password, and
then push [P1].
[P1]
When using the DTMF microphone:
Push the [0] to [9] digit keys on the microphone to enter
the password, and then push [#].
[UP] [DOWN]
PASSWORD
NOTE: If “PASSWORD” does not disappear after
pushing [P1], the password code you entered may
be incorrect. In this case, enter the correct password.
12345
For your reference:
When [Transceiver Password] is assigned to any key,
or the Transceiver Password item is preset in the
Menu screen and [Menu] is assigned to any key, the
start up password does not appear, even if the Transceiver Password is programmed.
In this case, push [Transceiver Password], or select
“Transceiver Password” in the Menu screen to enter
the Password Entry mode, then enter the password
as described above.
Channel 1
2-2
2
BASIC OPERATION
Selecting a zone
D Selecting a zone
To select a desired zone (Conventional group or NXDN
Trunking system).
➥ Push [Zone Up] or [Zone Down].
For your reference: What is “zone?”
Certain channels are grouped together and assigned
to a zone according to their intended use.
For example, ‘Staff A’ and ‘Staff B’ are assigned to a
“Business” zone, and ‘John’ and ‘Cindy’ are assigned
to a “Private” zone.
NOTE:
When you select the Conventional group zone, see
the page 2-4 for details of the channel selection.
When you select the NXDN Trunking system zone,
see page 7-3 for details of the GID (Group ID) selection.
2-3
2
BASIC OPERATION
Selecting a channel
D Selecting a channel
D Directly entering a channel
To select a desired operating channel:
➥ Push [CH/GID Up] or [CH/GID Down].
➥ Push one of the direct channel select keys, [Direct
CH/GID 1] to [Direct CH/GID 5].
You can select a channel by pushing [UP] or [DOWN] or
the [0] to [9] digit keys on the microphone, after pushing
[Channel Entry].
Or, when the Channel Entry function is assigned to the
keypad, you can select a channel by pushing [0] to [9]
digit keys on the microphone.
฀ •฀฀You฀can฀change฀the฀channel฀by฀pushing฀[Direct฀CH/GID฀
1] to [Direct CH/GID 5], as described below.
Changing the Direct channel setting:
q Select a desired channel.
w Hold down one of the [Direct CH/GID 1] to [Direct
CH/GID 5] keys for 3 seconds to set the selected
channel to the Direct channel 1 to 5.
q Push [Channel Entry] to enter the Channel Entry
mode.
CH ENTER MOD
CH No.
_ _
w Push [UP] or [DOWN] to select the channel number,
and then push [P1](SEL).
D Selecting a Home channel
฀ •฀฀Push฀[P0](BACK)฀to฀cancel฀the฀entry,฀and฀return฀to฀the฀
screen that you selected before entering the Channel Entry mode.
฀ •฀฀You฀can฀use฀the฀digit฀keys฀on฀the฀microphone.
The Home channel is an often-used Memory channel
you can preset in the transceiver.
➥ Push [Home CH/GID].
฀ •฀฀To฀change฀the฀Home฀channel,฀see฀the฀description฀
below.
Channel 1
Changing the Home channel setting:
q Select a desired channel.
w Hold down [Home CH/GID Select] for 3 seconds to
set the selected channel as the Home channel.
When using the DTMF microphone:
q Push the [0] to [9] digit keys to enter the Channel
Entry mode.
CH ENTER MOD
CH No.
_ 1
w Enter the channel number, and then push [#].
฀ •฀฀Push฀[M] to delete the entered number.
฀ •฀฀Push฀ [M] again to cancel the entry, and return to the
screen that you selected before entering the Channel
Entry mode.
Channel 1
• When the channel name is not programmed, the
selected zone and channel number are displayed.
(example: “1- 1”)
• When the programmed channel is less than 10, you
can select a channel without pushing [#].
For your reference:
You may be able to select a channel in the Menu
screen, depending on the presetting.
See section 5 for details.
2-4
2
BASIC OPERATION
Receiving
q Select a channel. (p. 2-4)
➥ Push [CH/GID Up] or [CH/GID Down].
➥ Push one of the direct channel select keys, [Direct
CH/GID 1] to [Direct CH/GID 5].
➥ Push the [0] to [9] digit keys of the optional DTMF
microphone to enter the channel number when
the Channel Entry function is assigned to the keypad, or after pushing [Channel Entry].
w When receiving a call, rotate [VOL] to adjust the audio output volume level.
D Setting the squelch level
The squelch circuit mutes the received audio, depending on the signal strength.
q Push [MENU].
฀ •฀Opens฀the฀Menu฀screen.
w Push [P2](Ω) or [P3](≈) to select the category that
has the “SQL LEVEL” item. (Default: “UTILITY”)
UTILITY
e Push [P1](ENT).
฀ •฀Enters฀the฀Menu฀Item฀Select฀mode.
r Push [P2](Ω) or [P3](≈) to select the “SQL LEVEL”
item.
UTILITY
SQL LEVEL
t Push [P1](ENT).
฀ •฀Enters฀the฀Squelch฀Level฀Adjustment฀mode.
y Push [UP] to increase the squelch level up to 9 (tight
squelch) or push [DOWN] to decrease the squelch
level down to 0 (loose squelch).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
LEVEL
u After setting, push [P1](EXIT).
฀ •฀Closes฀the฀Menu฀screen.
2-5
2
BASIC OPERATION
Transmitting
Wait until the channel is clear to avoid interference.
q Take the microphone off-hook.
฀ •฀While฀scanning,฀the฀scan฀stops.
w Wait for the channel to become clear.
฀ •฀฀The฀channel฀is฀busy฀when฀the฀LED฀indicator฀lights฀green.
e While holding down [PTT], speak at a normal voice
level.
r Release [PTT] to receive.
NOTE:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 to 10 cm (2 to 4 inches)
from your mouth, then speak at your normal voice
level.
D Transmitting notes
•฀Transmit฀inhibit฀function
The transceiver has several inhibit functions which restrict transmission under the following conditions:
- The channel is busy.
- An unmatched CTCSS tone or DTCS code is received, depending on the presetting.
- An unmatched or matched RAN code is received,
depending on the presetting.
- The selected channel is a ‘receive only’ channel.
•฀Time-out฀timer฀(TOT)
After continuous transmission for a preset time period, the time-out timer causes the transceiver to stop
transmitting.
•฀TOT฀Rekey฀timer
Once transmission is cut OFF, it is further inhibited for
a period determined by the TOT Rekey timer.
•฀MDC฀1200฀system฀operation
The MDC 1200 signaling system enhances your transceiver’s capabilities. It allows PTT ID signaling.
When you push or release [PTT], the transceiver
sends your unit ID, if preset.
ID
0001
When receiving a PTTID
from unit ID ‘0001.’
2-6
Section 3
ADVANCED OPERATION
DTMF Calls ...............................................................................3-2
Manual Dialing.........................................................................3-2
Autodial ...................................................................................3-2
Stun function ...........................................................................3-2
Editing the Autodial list ............................................................3-3
Adding an entry to the Autodial list ..........................................3-4
Emergency Calls......................................................................3-5
D Emergency Calls .....................................................................3-5
D Lone Worker Emergency Call..................................................3-5
Scrambler .................................................................................3-6
Radio฀Access฀Number฀(RAN) .................................................3-7
3-1
3
ADVANCED OPERATION
DTMF Calls
D Manual Dialing
➥ While holding down [PTT], push the keys on the
10-keypad to send the desired DTMF tones.
฀ •฀฀When฀[Keypad฀Auto฀PTT]฀is฀assigned฀to฀the฀keypad,฀you฀
can send the DTMF tones using the DTMF keypad without pushing [PTT].
[UP] [DOWN]
D Autodial
Autodial allows you to quickly send DTMF tones that
have been pre-entered onto your transceiver.
q Push [Autodial].
฀ •฀The฀irst฀entry฀in฀the฀Autodial฀list฀appears.
w Push [UP] or [DOWN] to select your desired number.
e Push [P3](TX) or [PTT] to send.
[P0], [P1], [P2], [P3]
For your reference:
When the Store & Send function is enabled, you can
sequentially send up to 30 of DTMF tones at one
time.
q Push [Autodial].
฀ •฀“CODE?”฀appears.
w Push [UP] or [DOWN] to enter a digit, and then
push [P1](SEL) to set.
฀ •฀Goes฀to฀the฀next฀digit฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀of฀the฀optional฀DTMF฀
microphone to enter a digit.
e Repeat step w until you enter up to 30 digits.
฀ •฀Push฀[P0](DEL)฀to฀delete฀the฀entered฀digit.
฀ •฀฀Push฀[P1](EXIT)฀to฀exit฀the฀DTMF฀Code฀Entry฀mode.
฀ •฀฀Push฀[P2](MODE)฀to฀toggle฀between฀the฀DTMF฀Code฀
Entry mode and the DTMF Autodial code selection
mode.
r Push [P3](TX) or [PTT] to send.
D Stun function
When the transceiver receives a stun code over the air,
the stun function is activated and the transceiver operation is inhibited. In this case, receiving a revive code is
necessary to operate the transceiver again.
This function is used when a transceiver is stolen or
lost.
3-2
3
ADVANCED OPERATION
DTMF Calls (Continued)
D Editing the Autodial list
q Push [Autodial Programming].
o Push [P1](ENT) to set.
฀ •฀“OVERWRITE?”฀appears.
AUTDIAL PRGM
AUTODIAL 1
OVERWRITE?
w Push [UP] or [DOWN] to select the number you want
to edit.
e Push [P1](ENT).
!0 Push [P1](OK) to overwrite.
฀ •฀฀Push฀ [P0](BACK)฀ to฀ return฀ to฀ the฀ DTMF฀ Code฀ Entry฀
mode.
฀ •฀Enters฀the฀Name฀Entry฀mode.
AUTDIAL PRGM
AUTODIAL 2
AUTODIAL 1
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SEL) to set.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀ can฀ use฀ the฀ 10-keypad฀ keys฀ of฀ the฀ optional฀ DTMF฀
microphone to enter a character.
t Repeat step r until you enter a name of up to 12
characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
AUTODIAL 2
y Push [P1](ENT) to save.
฀ •฀Enters฀the฀DTMF฀Code฀Entry฀mode.
11111
u Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set.
฀ •฀Goes฀to฀the฀next฀digit฀entry฀position.
฀ •฀฀You฀ can฀ use฀ the฀ 10-keypad฀ keys฀ of฀ the฀ optional฀ DTMF฀
microphone to enter a digit.
i Repeat step u until you enter a DTMF number of up
to 16 digits.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀digit.
11112
3-3
3
ADVANCED OPERATION
DTMF Calls (Continued)
D Adding an entry to the Autodial list
q Push [Autodial Programming].
u Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set.
AUTDIAL PRGM
AUTODIAL 1
฀ •฀Goes฀to฀the฀next฀digit฀entry฀position.
฀ •฀฀You฀ can฀ use฀ the฀ 10-keypad฀ keys฀ of฀ the฀ optional฀ DTMF฀
microphone to enter a digit.
w Push [UP] or [DOWN] to select a blank number.
i Repeat step u until you enter a DTMF number of up
to 16 digits.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀digit.
AUTDIAL PRGM
BLANK
04
12345
e Push [P1](ENT).
o Push [P1](ENT) to set.
฀ •฀Enters฀the฀Name฀Entry฀mode.
฀ •฀“NAME?”฀appears.
฀ •฀“STORE?”฀appears.
STORE?
NAME?
!0 Push [P1](OK) to store.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SEL) to set.
฀ •฀฀Push฀ [P0](BACK)฀ to฀ return฀ to฀ the฀ DTMF฀ Code฀ Entry฀
mode.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀ can฀ use฀ the฀ 10-keypad฀ keys฀ of฀ the฀ optional฀ DTMF฀
microphone to enter a character.
AUTDIAL PRGM
AUTODIAL 4
t Repeat step r until you enter a name of up to 12
characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
AUTODIAL 4
y Push [P1](ENT) to set.
฀ •฀Enters฀the฀DTMF฀Code฀Entry฀mode.
฀ •฀“CODE?”฀appears.
CODE?
3-4
3
ADVANCED OPERATION
Emergency Calls
D Emergency Calls
When [Emergency] is assigned to [R], you can manually make an Emergency call.
q Hold down [R] for 1 second.
฀ •฀Enters฀the฀Emergency฀mode.
฀ •฀฀When฀the฀transceiver฀enters฀the฀Emergency฀mode,฀it฀will฀
change to the Emergency channel and begin transmitting, according to the presetting.
[R]
w To exit from the Emergency mode, hold down [R]
again, or turn OFF the power.
฀ •฀฀If฀ the฀ Emergency฀ mode฀ completes฀ a฀ preset฀ number฀ of฀
call cycles, the transceiver will automatically exit the
mode and return to the zone and channel that was in use
before you entered the Emergency mode.
NOTE:
The Emergency Mode Type can be set to “Silent” or
“Audible” by using the optional cloning software.
When “Audible” is set, the transceiver sounds a beep
when transmitting in the Emergency mode.
D Lone Worker Emergency Call
When the Lone Worker function is activated, the Emergency function is automatically turned ON, after the
preset time period has passed with no operation performed.
➥ Push [Lone Worker] to turn the function ON or OFF.
3-5
3
ADVANCED OPERATION
Scrambler
The Voice Scrambler function provides private communication between stations. All transceiver versions have
a built-in scrambler.
➥ Push [Scrambler/Encryption] to turn the function ON
or OFF.
฀ •฀“ ” appears when the Scrambler function is ON.
฀ •฀฀After฀ turning฀ ON฀ the฀ function,฀ push฀ [PTT]฀ to฀ make฀ an฀
encrypted call.
✓ Changing the Scrambler code setting:
q Hold down [Scrambler/Encryption Code] to enter the
Scrambler Code Setting mode.
฀ •฀฀The฀length฀of฀time฀you฀hold฀down฀[Scrambler/Encryption฀
Code] may differ, depending on the presetting.
w Push [UP] or [DOWN] to select a desired code.
e Push [P1](EXIT) to save and exit.
฀ •฀฀Even฀if฀the฀Scrambler฀function฀is฀OFF฀in฀step฀q, it automatically turns ON after exiting the Scrambler Code setting mode.
3-6
3
ADVANCED OPERATION
Radio฀Access฀Number฀(RAN)
RAN is a signaling system designed for digital radio
communications.
When a channel is set up with a RAN, the squelch will
open only when a call containing a matching RAN is
received.
If a call containing a different RAN is made on the same
channel you are using, you will not hear the call.
3-7
Section 4
SCAN OPERATION
Scan operation.........................................................................4-2
Temporary channel lockout ....................................................4-3
Priority scan .............................................................................4-4
D Setting a Priority channel ........................................................4-4
Scan Revert channel ...............................................................4-5
Scan delete/add .......................................................................4-6
4-1
4
SCAN OPERATION
Scan operation
A scan monitors for signals on the transceiver channels.
While scanning, the transceiver checks for a signal on
each channel and stops when a signal is received.
For your reference:
Before starting a scan, set the following items:
•฀฀Set฀3฀scan฀types฀in฀the฀transceiver:฀฀Single,฀ Multi฀ or฀
List.
•฀฀Set฀the฀scan฀type฀in฀both฀the฀conventional฀and฀trunking zones.
•฀฀Set฀Priority฀channels,฀but฀only฀in฀conventional฀type฀
zones.
➥ Push [Scan] each time to start or stop a scan.
฀ •฀“ ” appears while scanning.
฀ •฀฀When฀the฀transceiver฀detects฀a฀signal,฀the฀scan฀pauses฀
on the channel. The transceiver remains on the busy
channel until the signal disappears, and then the scan
resumes.
When you select a conventional zone, trunking zones
are not scanned.
When you select a trunking zone, conventional zones
are not scanned.
SCAN
While scanning
Select the desired zone to start scanning.
•฀Single:฀฀ ฀The฀ transceiver฀ scans฀ the฀ preset฀ target฀
channels or GIDs in only the selected zone.
For a Priority scan, all Priority channels will
also be scanned, even if they are in other
conventional type zones.
•฀Multi:฀ ฀ T
฀ he฀ transceiver฀ scans฀ the฀ preset฀ target฀
channels or GIDs in only the preset target
zones.
For a Priority scan, all Priority channels will
also be scanned, even if they are in other
conventional type zones.
•฀List:฀ ฀ T
฀ he฀ transceiver฀ scans฀ the฀ preset฀ target฀
channels or GIDs in only the zones that are
preset on the Scan List.
For a Priority scan, all Priority channels will
also be scanned, even if they are in conventional type zones that are not on the List.
NOTE: Two or more channels must be programmed
to start a scan.
NOTE:
When the scan starts in the Conventional group zone,
the NXDN Trunking system zone is not scanned.
When the scan starts in the NXDN Trunking system
zone, the Conventional group zone is not scanned.
4-2
4
SCAN OPERATION
Temporary channel lockout
During a scan, you can temporarily delete a channel
from a scanning sequence.
This function speeds up scanning by skipping unwanted channels.
q Start the scan. (p. 4-2)
฀ •฀When฀a฀signal฀is฀received,฀the฀scan฀pauses.
w While the scan is paused, and if you want to skip the
frequency, push [Scan Delete/Add].
฀ •฀฀“Ú” (scan target channel icon) disappears when the selected channel is deleted from the scanning sequence.
฀ •฀฀The฀channel฀is฀no฀longer฀scanned.฀However,฀depending฀
on the presetting, the deleted channel may be added to
the scan group again after the scan is cancelled.
See also: “Scan delete/add” on page 4-6
4-3
4
SCAN OPERATION
Priority scan
The Priority scan scans all scan target channels or
GIDs in the zone while also monitoring the Priority 1
and Priority 2 channels.
When the scan is paused on the Priority 1 channel, the
other channels are not monitored.
D Setting a Priority channel
Depending on the presetting, you can manually set a
Priority channel (Priority 1, Priority 2 or Priority 1 & 2).
q Select a channel that you want to set as a Priority
channel.
Channel 1
w Push [Priority-channel Select].
฀ •฀Enters฀the฀Priority฀Channel฀Setting฀mode.
PRI CH SEL
NORMAL
e Push [UP] or [DOWN] to select “PRIORITY 1,”
“PRIORITY 2” or “PRIORITY 1 & 2.”
PRI CH SEL
PRIORITY 1
r Push [P1](OK).
฀ •฀฀The฀selected฀channel฀is฀set฀as฀a฀Priority฀channel.
NOTE: When “PRIORITY 1 & 2” is selected, the
same channel is set as both Priority 1 and Priority 2
channels.
4-4
4
SCAN OPERATION
Scan Revert channel
The Scan Revert channel is automatically selected
when you push [PTT] to make a call during a scan.
The Scan Revert channel can be set to the transceiver
using the optional cloning software.
•฀Last฀Called฀+฀Selected:฀
The transceiver makes a call on the last channel
or GID that you received a call on.
However, if you push [PTT] while the scan is
paused, the transceiver makes a call on the channel or to the GID that the scan is paused on.
When you change the channel or GID before
starting a scan, the transceiver makes a call on
the selected channel or to the GID until the transceiver receives another call.
•฀Selected:
The transceiver makes a call on the channel or to
the GID selected before a scan.
•฀Selected฀+฀Talkback:
The transceiver makes a call on the channel or to
the GID selected before a scan.
However, if you push [PTT] when the scan is
paused, the transceiver makes a call on the channel or to the GID that the scan is paused on.
•฀Priority฀1:
The transceiver makes a call on the Priority 1
channel.
•฀Priority฀1฀+฀Talkback:
The transceiver makes a call on the Priority 1
channel.
However, if you push [PTT] when the scan is
paused, the transceiver makes a call on the channel or to the GID that the scan is paused on.
•฀Priority฀2:
The transceiver makes a call on the Priority 2
channel.
•฀Priority฀2฀+฀Talkback:
The transceiver makes a call on the Priority 2
channel.
However, if you push [PTT] when the scan is
paused, the transceiver makes a call on the channel or to the GID that the scan is paused on.
4-5
4
SCAN OPERATION
Scan delete/add
During scan, you can temporarily delete a channel or
zone from the scanning sequence.
q Select a channel, GID or zone that you want to delete from the sequence.
w Push [Scan Delete/Add].
฀ •฀฀“Ú” disappears when the selected channel, GID or zone
is deleted from the scanning sequence.
Channel 1
To manually add a channel, GID or zone to the scanning sequence, repeat steps q and w.
•฀฀“Ú” appears when the selected channel is added to the
sequence.
4-6
Section 5
MENU SCREEN
Menu screen description ........................................................5-2
D Entering the Menu screen .......................................................5-2
Menu functions ........................................................................5-3
5-1
5
MENU SCREEN
Menu screen description
When [Menu] is assigned, you can open the Menu
screen.
In the Menu screen, the items are categorized.
Depending on the presetting, you can select various
functions and adjust the transceiver settings in the
Menu screen.
CONTACT
Menu screen (Sample)
D Entering the Menu screen
Example: Setting the squelch level
q Push [MENU].
฀ •฀Opens฀the฀Menu฀screen.
w Push [P2](Ω) or [P3](≈) to select the category that
has the “SQL LEVEL” item. (Default: “UTILITY”)
UTILITY
e Push [P1](ENT).
฀ •฀Enters฀the฀Menu฀Item฀Select฀mode.
r Push [P2](Ω) or [P3](≈) to select the “SQL LEVEL”
item.
UTILITY
SQL LEVEL
t Push [P1](ENT).
฀ •฀Enters฀the฀Squelch฀Level฀Adjustment฀mode.
y Push [UP] to increase the squelch level up to 9 (tight
squelch), or push [DOWN] to decrease the squelch
level down to 0 (loose squelch).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
LEVEL
u After setting, push [P1](EXIT).
฀ •฀Closes฀the฀Menu฀screen.
For your reference:
You can close the Menu screen by pushing [R], even
if an item is selected.
5-2
5
MENU SCREEN
Menu functions
Autodial “AUTO DIAL”
Opens the DTMF Autodial code selection screen.
Broadcast “BROADCAST”
❍ In the NXDN Trunking system
Turns the Broadcast Call ON or OFF.
This item can also be used to make a Broadcast Group
Call.
q When “AUTO DIAL” is displayed, push [P1](ENT).
฀ •฀The฀irst฀entry฀in฀the฀Autodial฀list฀appears.
w Push [UP] or [DOWN] to select a desired number.
e Push [P3](TX) to send.
q When “BROADCAST” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
When the Store & Send function is enabled:
q When “AUTO DIAL” is displayed, push [P1](ENT).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
฀ •฀“CODE?”฀appears.
w Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set.
When “ON” is selected in step w, push [PTT] to send
the Broadcast Group Call.
฀ •฀Goes฀to฀the฀next฀digit฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
Direct CH/GID 1 Select to Direct CH/GID 5 Select
“DIRECT CHGD1” to “DIRECT CHGD5”
Sets the selected channel or GID to a Direct CH/GID
between 1 and 5.
e Repeat step w until you enter up to 30 digits.
฀ •฀Push฀[P0](DEL)฀to฀delete฀the฀entered฀digit.
฀ •฀฀Push฀[P1](EXIT)฀to฀exit฀the฀DTMF฀Code฀Entry฀mode.
฀ •฀฀Push฀[P2](MODE)฀to฀toggle฀between฀the฀DTMF฀Code฀Entry mode and the DTMF Autodial code selection mode.
q Select a desired channel. (p. 2-4)
w Push [MENU].
r Push [P3](TX) to send.
฀ •฀Opens฀the฀Menu฀screen.
e When a channel between “DIRECT CHGD1” and
“DIRECT CHGD5” is displayed, push [P1](ENT).
Autodial Programming “AUTDIAL PRGM”
Enters the DTMF Code Programming mode.
฀ •฀฀Sets฀the฀selected฀channel฀to฀a฀Direct฀channel฀between฀1฀
and 5.
q When “AUTDIAL PRGM” is displayed, push [P1](ENT).
฀ •฀The฀irst฀entry฀in฀the฀Autodial฀list฀appears.
Display Format “DISP FORMAT”
❍ In the Analog mode or
NXDN Conventional system
Toggles the display format between the channel name
and the zone and channel number.
w Push [UP] or [DOWN] to select a desired number.
e Push [P1](ENT).
฀ •฀Enters฀the฀Name฀Entry฀mode.฀(p.฀3-3)
AUX A “AUX A”
Turns the AUX A port ON or OFF.
❍ In the NXDN Trunking system
Toggles the display format between the GID name and
the GID number.
q When “AUX A” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
q When “DISP FORMAT” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select “CH NAME” or
“ZONE-CH No.”
e Push [P1](OK) to save.
AUX B “AUX B”
Turns the AUX B port ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
q When “AUX B” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
External Speaker “EXT SPEAKER”
Turns the External speaker function ON or OFF.
When the External speaker function is ON, the PA
speaker that is connected to the D-Sub 15-pin will activate.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
q When “EXT SPEAKER” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
5-3
5
MENU SCREEN
Menu functions (Continued)
Fixed Volume “FIXED VOLUME”
Toggles the tone level between “High” and “Low,” or
turns OFF the tone.
Group + SDM (NXDN)฀฀“GROUP+SDM”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode, and then the Short Data
Message Entry mode.
q When “FIXED VOLUME” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select “LOW,” “HIGH” or
“OFF.”
q ฀When฀“GROUP+SDM”฀is฀displayed,฀push฀[P1](ENT).
w Push [UP] or [DOWN] to select a desired GID.
e Push [P1](ENT).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
Forced Search “FORCE SEARCH”
❍ In the NXDN Trunking system
Starts to search for a site.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
➥ When “FORCE SEARCH” is displayed, push [P1]
(ENT).
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀Displays฀“SEARCHING.”
฀ •฀฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
GPS Position Display “GPS POS DISP”
Enters the GPS Position Display mode.
In the GPS Position Display mode, you can check your
latitude and longitude position.
y Push [PTT] to send the message to the selected
GID.
Group + Status (NXDN)฀฀“GROUP+STATUS”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode, and then the Status Message Entry mode.
q When “GPS POS DISP” is displayed, push [P1]
(ENT).
฀ •฀฀You฀can฀check฀your฀latitude฀and฀longitude฀position.
w Push [UP] or [DOWN] to toggle between the latitude
and longitude position display.
฀ •฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀Push฀[P1](EXIT)฀to฀the฀GPS฀Position฀Display฀mode.
฀ •฀฀Push฀[P2](DISP)฀to฀automatically฀switch฀the฀latitude฀and฀
longitude position display.
q ฀When฀ “GROUP+STATUS”฀ is฀ displayed,฀ push฀ [P1]
(ENT).
w Push [UP] or [DOWN] to select a desired GID, and
then push [P1](ENT).
฀ •฀Enters฀the฀Status฀Message฀Selection฀mode.
Group (NXDN) “GROUP MODE”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Group Call mode.
In the NXDN Conventional system, this function is used
for Group Calls.
In the NXDN Trunking system, the Group ID List is displayed, but the transceiver cannot make Group calls.
e Push [UP] or [DOWN] to select the status message
that you want to send.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
r Push [P3](TX) to send the message to the selected
GID.
q When “GROUP MODE” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select a desired GID.
e Push [PTT] to call the selected GID.
5-4
5
MENU SCREEN
Menu functions (Continued)
High Transmit Power “HI TX POWER”
❍ In the NXDN Trunking system
Toggles the transmit power level.
Individual + SDM (NXDN)฀฀“INDIV+SDM”
Enters the Individual Call mode, and then the Short
Data Message Entry mode.
When “Auto” is set as the default:
q When “HI TX POWER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON (High) or OFF
(Auto).
q ฀When฀“INDIV+SDM”฀is฀displayed,฀push฀[P1](ENT).
w Push [UP] or [DOWN] to select a desired unit ID.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
e Push [P1](ENT).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
e Push [P1](OK) to save.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
When “Low” is set as the default:
q When “HI TX POWER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON (High) or OFF
(Low).
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
฀ •฀฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
See page 5-6 about [Low Transmit Power].
y Push [PTT] to send the message to the selected unit
ID.
Home CH/GID Select “HOME CHANNEL”
Sets the selected channel or GID as the Home Channel.
Individual + Status (NXDN)฀฀“INDIV+STATUS”
Enters the Individual Call mode, and then the Status
Message Entry mode.
q Select a desired channel. (p. 2-4)
w Push [MENU].
฀ •฀Opens฀the฀Menu฀screen.
q ฀When฀“INDIV+STATUS”฀is฀displayed,฀push฀[P1](ENT).
w Push [UP] or [DOWN] to select a desired unit ID.
e When “HOME CHANNEL” is displayed, push [P1]
(ENT).
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
฀ •฀Sets฀the฀selected฀channel฀or฀GID฀as฀the฀Home฀Channel.
Horn Alert “HORN ALERT”
Turns the Horn Alert function ON or OFF.
When this function is ON, the horn alert port will be activated for a preset time period after receiving a call.
e Push [P1](ENT).
q When “HORN ALERT” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
฀ •฀Enters฀the฀Status฀Message฀Selection฀mode.
e Push [UP] or [DOWN] to select a status message
that you want to send.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
r Push [P3](TX) to send the message to the selected
unit ID.
Individual (NXDN) “INDIVIDUAL”
Enters the Individual Call mode.
q When “INDIVIDUAL” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select a desired unit ID.
LCD Brightness “LCD BRIGHT”
Selects the brightness of the function display and keys
backlight.
Select High, Low or OFF to meet your needs.
The function display and keys can be backlit for better
visibility under low light conditions.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
e Push [P3](TX) to call to the selected unit ID.
q When “LCD BRIGHT” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select “LOW,” “HIGH” or
“OFF.”
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
5-5
5
MENU SCREEN
Menu functions (Continued)
Lone Worker “LONE WORKER”
Turns the Lone Worker function ON or OFF. (p. 3-5)
Monitor “MONITOR”
❍ In the Analog mode
Turns the Monitor ON or OFF.
When the Monitor is ON, the transceiver releases the
CTCSS mute.
q When “LONE WORKER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
❍ In the NXDN Conventional system
Turns the Monitor ON or OFF.
When the Monitor is ON, the transceiver releases the
RAN code mute.
e Push [P1](OK) to save.
Low Transmit Power “LOW TX POWER”
❍ In the Analog mode or
NXDN Conventional system
Toggles the transmit power between “High” and “Low,” if
“High” is set as the default.
q When “MONITOR” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
q When “LOW TX POWER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON (Low) or OFF
(High).
Operator Selectable Tone “OST”
Turns the OST (Operator Selectable Tone) mode ON
or OFF.
When the OST mode is ON, the selected tone in the
OST list is enabled.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
q When “OST” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
❍ In the NXDN Trunking system
Toggles the transmit power level.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
When the transmit power level is set to “Auto” as the
default:
q When “LOW TX POWER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON (Low) or OFF
(Auto).
OST List “OST LIST”
Displays the OST (Operator Selectable Tone) list.
q When “OST LIST” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select a desired OST tone
or turn OFF the OST tone.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](EXIT) to exit.
When the transmit power level is set to “High” as the
default:
q When “LOW TX POWER” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON (Low) or OFF
(High).
Priority-channel Select “PRI CH SEL”
Enters the Priority Channel Select mode for a Priority
scan.
q Select a desired channel. (p. 2-4)
w Push [MENU].
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
฀ •฀Opens฀the฀Menu฀screen.
e When “PRI CH SEL” is displayed, push [P1](ENT).
r Push [UP] or [DOWN] to select “PRIORITY 1,” “PRIORITY 2,” “PRIORITY 1 & 2” or “NORMAL.”
See page 5-5 about [High Transmit Power].
Maintenance “MAINTENANCE”
Enters the Maintenance Display mode.
In the Maintenance Display mode, you can check the
RSSI level of the selected channel for installation or
maintenance of the system.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
t Push [P1](OK).
฀ •฀฀Sets฀the฀selected฀channel฀to฀Priority฀1,฀Priority฀2,฀Priority฀
1 and 2 or a Normal channel.
NOTE: When “PRIORITY 1 & 2” is selected, the
same channel is set as both Priority 1 and Priority 2
channels.
q When “MAINTENANCE” is displayed, push [P1](ENT).
฀ •฀Displays฀the฀RSSI฀level.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
w Push [P1](EXIT) to exit.
5-6
5
MENU SCREEN
Menu functions (Continued)
Public Address “PUB ADDRESS”
Turns the Public Address function ON or OFF.
When this function is ON, you can make announcements through a PA speaker.
•฀Transmitting฀is฀disabled฀while฀in฀the฀PA฀mode.
RX Low Cut “RX LOW CUT”
While receiving a digital signal, this function cuts the
frequency components at 300 Hz or below.
q When “RX LOW CUT” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
q When “PUB ADDRESS” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON or OFF.
e Push [P1](EXIT) to save.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
Scan “SCAN”
Starts or stops a scan.
e Push [P1](OK) to save.
q When “SCAN” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
RX Audio Equalizer “RX AUDIO EQ”
This function sets the audio characteristics type to apply to the received audio.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK).
฀ •฀฀A฀scan฀starts฀when฀“ON”฀is฀selected฀in฀step฀w.
฀ •฀฀A฀scan฀stops฀when฀“OFF”฀is฀selected฀in฀step฀w.
q When “RX AUDIO EQ” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select the option.
Scan Delete/Add “SCAN DEL/ADD”
Sets or cancels the selected channel or GID as the
scan target.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀FLAT:
Selects the standard audio characteristics.
฀ •฀HIGH฀BOOST:
Emphasizes the treble range.
฀ •฀LOW฀BOOST:
Suppresses the treble range and boosts the
bass range.
e Push [P1](EXIT) to save.
q Select a desired channel. (p. 2-4)
w Push [MENU].
฀ •฀Opens฀the฀Menu฀screen.
e When “SCAN DEL/ADD” is displayed, push [P1]
(ENT).
r Push [UP] or [DOWN] to select “DELETE” or “ADD.”
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
t Push [P1](OK).
RX Auto Gain Control “RX AUTO GAIN”
This function automatically adjusts the received audio
volume to an appropriate level so that you can clearly
hear the audio.
฀ •฀฀The฀selected฀channel฀is฀canceled฀as฀a฀scan฀target฀when฀
“DELETE” is selected in step r.
฀ •฀฀The฀selected฀channel฀is฀set฀as฀a฀scan฀target฀when฀“ADD”฀
is selected in step r.
q When “RX AUTO GAIN” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select the option.
Scrambler/Encryption “SCRAM/ENCRYP”
❍ In the Analog mode
Turns the Scrambler function ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀OFF:฀ ฀Disables฀the฀Auto฀Gain฀Control.฀The฀received฀
audio level is only adjusted by [VOL].
฀ •฀HIGH:฀฀Enables฀the฀Auto฀Gain฀Control.฀The฀received฀
audio level will be automatically adjusted to
an appropriate constant level, according to
the [VOL] setting. However, the background
noise will be boosted, and howling may occur, depending on your operating environment.
฀ •฀LOW:฀ ฀Enables฀the฀Auto฀Gain฀Control.฀The฀received฀
audio level will be automatically adjusted to
an appropriate constant level, according
to the [VOL] setting. However, the adjustable gain is smaller than the “HIGH” setting.
Therefore, background noise boosting will
also be smaller, and howling may not occur.
e Push [P1](EXIT) to save.
❍ In the NXDN Conventional system or
the NXDN Trunking system
Turns the Encryption function ON or OFF.
q When “SCRAM/ENCRYP” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
5-7
5
MENU SCREEN
Menu functions (Continued)
Scrambler/Encryption Code “SCRAM CODE”
❍ In the Analog mode
Enters the Scrambler Code Selection mode.
Site Number “SITE No.”
❍ In the NXDN Trunking system
Display the current Site number.
❍ In the NXDN Conventional system or
the NXDN Trunking system
Enters the Encryption Key Selection mode.
➥ When “SITE No.” is displayed, push [P1](ENT).
฀ •฀฀Displays฀the฀current฀Site฀number฀for฀3฀seconds,฀and฀then฀
exits the Menu screen.
q When “SCRAM CODE” is displayed, push [P1]
(ENT).
Site Select “SITE”
❍ In the NXDN Trunking system
Enters the Site Select mode.
฀ •฀฀The฀ Scrambler฀ or฀ the฀ Encryption฀ function฀ automatically฀
turns ON.
w Push [UP] or [DOWN] to select a desired Scrambler
code or Encryption key.
q When “SITE” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select a desired site.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](EXIT) to save.
e Push [P1](SEL) to save.
SDM (NXDN) “SHRT MSG MOD”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Directly enters the Short Message mode.
Squelch Level “SQL LEVEL”
❍ In the Analog mode
Enters the Squelch Level Adjustment mode.
฀ •฀“MESSAGE?”฀appears.
q When “SQL LEVEL” is displayed, push [P1](ENT).
w Push [DOWN] to decrease the squelch level down
to 0 (loose squelch), or push [UP] to increase the
squelch level up to 9 (tight squelch).
w Push [UP] or [DOWN] to enter a character, and then
push [P1](SEL) to set.
e Push [P1](EXIT) to exit.
q When “SHRT MSG MOD” is displayed, push [P1]
(ENT).
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
Squelch Off “SQL OFF”
❍ In the Analog mode or
the NXDN Conventional system
Opens the squelch, and releases the mute.
e Repeat step w until you enter a message of up to
100 characters.
฀ •฀฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
q When “SQL OFF” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
r Push [PTT] to send the message to the Base ID.
t Push [P1](EXIT) to exit.
e Push [P1](OK) to exit.
Stack “STACK”
Enters the Memory Stack mode.
Send the GPS Data “SND GPS DATA”
❍ In the NXDN Conventional system or
the NXDN Trunking system
Sends the position data that is received from the GPS
receiver to a Base station.
q When “STACK” is displayed, push [P1](ENT).
q When “SND GPS DATA” is displayed, push [P1](ENT).
w Push [P1](ENT) to send.
฀ •฀฀Push฀[P0](DEL)฀to฀delete฀the฀selected฀message.
฀ •฀฀Push฀[P2](DISP)฀to฀change฀the฀display฀item฀between฀received ID, message contents and channel number.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
w Push [UP] or [DOWN] to select a desired message.
e Push [P1](EXIT) to exit.
Site Lock “SITE LOCK”
❍ In the NXDN Trunking system
Turns the Site Lock function ON or OFF.
q When “SITE LOCK” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](OK) to save.
5-8
5
MENU SCREEN
Menu functions (Continued)
Status (NXDN) “STATUS”
Directly enters the Status Message mode.
TX Audio Equalizer “TX AUDIO EQ”
This function sets the audio characteristics type to apply to the transmit audio.
q When “STATUS” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select a status message.
q When “TX AUDIO EQ” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select the option.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀optional฀DTMF฀
microphone.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀FLAT:
Selects the standard audio characteristics.
฀ •฀HIGH฀BOOST:
Selects the audio characteristics emphasizing
the treble range.
฀ •฀LOW฀BOOST:
Suppresses the treble range and boosts the
bass range.
e Push [P1](EXIT) to save.
e Push [P3](TX) to send the message to the Base ID.
r Push [P1](EXIT) to exit.
Talk Around “TALK AROUND”
❍ In the Analog mode
Turns the talk around function ON or OFF.
q When “TALK AROUND” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON or OFF.
e Push [P1](OK) to save.
TX Auto Gain Control “TX AUTO GAIN”
This function automatically adjusts the transmit audio
level to an appropriate constant level so that the called
station can hear the audio clearly.
Transceiver Password “PASSWORD”
Enters the Password Entry mode.
The transceiver cannot be used until you enter a correct password.
q When “TX AUTO GAIN” is displayed, push [P1](ENT).
w Push [UP] or [DOWN] to select ON or OFF.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀ON:฀ ฀Enables฀the฀Auto฀Gain฀Control.฀The฀transmit฀
audio level will be adjusted to an appropriate
constant level.
฀ •฀OFF:฀ ฀Disables฀the฀Auto฀Gain฀Control.
e Push [P1](EXIT) to save.
q When “PASSWORD” is displayed, push [P1](ENT).
฀ •฀Enters฀the฀Password฀Entry฀mode.
w Push [UP] or [DOWN] to enter a digit code, and then
push [P1] to set.
฀ •฀฀Goes฀to฀the฀next฀digit฀entry฀position.
e Repeat step w until you enter the password, and
TX Noise Suppressor “TX NOISE SUP”
This function enables transmitting while in the digital
mode and reducing or eliminating the noise component
in the background noise.
then push [P1].
When using the DTMF microphone:
Push the [0] to [9] digit keys on the microphone to enter
the password, and then push [#].
q When “TX NOISE SUP” is displayed, push [P1]
(ENT).
w Push [UP] or [DOWN] to select ON or OFF.
NOTE: If “PASSWORD” does not disappear after
pushing [P1], the password code you entered may
be incorrect. In this case, enter the correct password.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
e Push [P1](EXIT) to save.
Zone Delete/Add “ZONE DEL/ADD”
Sets or cancels the selected zone as a scan target.
q Select a desired zone. (p. 2-3)
w Push [MENU].
฀ •฀Opens฀the฀Menu฀screen.
e When “ZONE DEL/ADD” is displayed, push [P1]
(ENT).
r Push [UP] or [DOWN] to select “DELETE” or “ADD.”
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
t Push [P1](OK).
฀ •฀฀The฀ selected฀ zone฀ is฀ canceled฀ as฀ a฀ scan฀ target฀ when฀
“DELETE” is selected in step r.
฀ •฀฀The฀selected฀zone฀is฀set฀as฀a฀scan฀target฀when฀“ADD”฀is฀
selected in step r.
5-9
Section 6
NXDN OPERATION 
NXDN system operation..........................................................6-2
Memory Stack ..........................................................................6-3
D Viewing a stored message ......................................................6-3
D Deleting a desired message ....................................................6-4
D Deleting all stored messages ..................................................6-4
6-1
6
NXDN OPERATION 
NXDN system operation
NXDN is a “Common Air Interface” (CAI), the name for
over-the-air methods by which transceivers and repeaters communicate. NXDN defines the next-generation
digital protocol.
The NXDN system has two operating modes, conventional and trunking.
In an NXDN conventional system, you should manually
search for a clear channel.
In an NXDN trunking system, the repeater automatically searches for a clear channel, and sends the information to the transceivers.
In addition, Type-C requires a Control Channel repeater.
If you use an NXDN transceiver, you can transmit and
receive Individual Calls, Group Calls, Status Messages,
Short Messages, and so on.
6-2
6
NXDN OPERATION 
Memory Stack
D Viewing a stored message
The transceiver has a Memory Stack. When the transceiver receives a Status Message or a Short Message,
the received content is stored in the transceiver’s Memory Stack.
If you turn OFF the transceiver’s power, the contents
will be cleared.
q When a transceiver receives data:
฀ •฀฀Displays฀“DATA฀RCVD,”฀“COMPLETE,”฀the฀received฀message, the caller’s unit ID and GID*.
*Displays only when the received call is a Group call.
฀ •฀“ ” blinks.
w Push [Stack].
฀ •฀Enters฀the฀Memory฀Stack฀mode.
฀ •฀Displays฀“STACK.”
The stored messages are displayed using the following
indication.
Information
Message type
Caller ID Stack
Status Message
Short Message
Stored number Stored number
Display items
Caller ID
Message contents
Received channel or GID
e Push [UP] or [DOWN] to select a desired message.
r Push [P2](DISP) to change the displayed item between received ID, message contents and channel
number.
Indication
“ID”
“ST”
“SM”
“01” to “15”
“ID”
STACK
SM01 ID
“MSG”
“CH”
STACK
UID 0001
Received ID
STACK
SM01 MSG
STACK
SHORT MESSAG
Message contents
Scrolls
STACK
SM01 CH
STACK
CH
Channel number
t Push [P1](EXIT).
฀ •฀Exits฀the฀Memory฀Stack฀mode.
6-3
CH01
6
NXDN OPERATION 
Memory Stack (Continued)
D Deleting a desired message
q Push [Stack].
฀ •฀Enters฀the฀Memory฀Stack฀mode.
฀ •฀Displays฀“STACK.”
w Push [UP] or [DOWN] to select a desired message.
e Push [P0](DEL).
฀ •฀Displays฀“DELETE?.”
r Push [P1](OK).
฀ •฀Deletes฀the฀selected฀message.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀฀Push฀[R] to exit the Memory Stack mode.
D Deleting all stored messages
q Push [Stack].
฀ •฀Enters฀the฀Memory฀Stack฀mode.
฀ •฀Displays฀“STACK.”
w Hold down [P0](DEL) for 1 second.
฀ •฀Displays฀“ALL฀DELETE?.”
e Push [P1](OK).
฀ •฀Deletes฀all฀messages.
฀ •฀฀Push฀[P0](BACK)฀to฀return฀to฀the฀previous฀screen.
฀ •฀฀Push฀[R] to exit the Memory Stack mode.
6-4
Section 7
NXDN OPERATION 
NXDN trunking operation........................................................7-2
Selecting฀a฀GID฀(Group฀ID) .....................................................7-3
D Selecting a GID ......................................................................7-3
D Selecting a Home GID.............................................................7-3
D Directly entering a GID ............................................................7-3
Transmitting a call ...................................................................7-4
Group call (Transmission Trunked) ..........................................7-4
Individual call (Transmission Trunked) .....................................7-5
Group call (Message Trunked) ................................................7-6
Individual call (Message Trunked) ...........................................7-6
Broadcast Group call ...............................................................7-7
Status call ................................................................................7-7
Short Data call.........................................................................7-8
Long Data call .........................................................................7-8
Telephone call .........................................................................7-9
Receiving a call........................................................................7-10
Group call ................................................................................7-10
Individual call ...........................................................................7-10
Broadcast Group call ...............................................................7-11
Status call ................................................................................7-11
Short Data call.........................................................................7-12
Long Data call .........................................................................7-12
Telephone call .........................................................................7-13
Forced Search ..........................................................................7-14
7-1
7
NXDN OPERATION 
NXDN trunking operation
When you select the NXDN Trunking system mode,
your transceiver automatically searches for, and selects a clear channel.
To use the NXDN Trunking system mode, your transceiver must register to a Control Channel repeater.
Before operating in the NXDN Trunking system mode,
select the NXDN Trunking System zone. (p. 2-3)
7-2
7
NXDN OPERATION 
Selecting฀a฀GID฀(Group฀ID)
D Selecting a GID
D Directly entering a GID
To select a desired GID, do one of the following:
➥ Push [CH/GID Up] or [CH/GID Down].
➥ Push one of the direct GID select keys, [Direct CH/
GID 1] to [Direct CH/GID 5].
฀ •฀฀You฀can฀change฀the฀GID฀that฀is฀selected฀by฀pushing [Direct CH/GID 1] to [Direct CH/GID 5], as described below.
You can select a GID by pushing [UP] or [DOWN], or
the [0] to [9] digit keys on the microphone, after pushing
[Channel Entry].
Or, when the Channel Entry function is assigned to the
keypad, you can select a GID by pushing the [0] to [9]
digit keys.
q Push [Channel Entry] to enter the GID Entry mode.
Changing the Direct GID setting:
q Select a desired GID.
w Hold down one of the [Direct CH/GID 1] to [Direct
CH/GID 5] keys for 3 seconds to set the selected
GID to the Direct GID 1 to 5.
CH ENTER MOD
CH No.
_ _
w Push [UP] or [DOWN] to select the GID, and then
push [P1](SEL).
฀ •฀฀Push฀[P0](BACK)฀to฀cancel฀the฀entry,฀and฀return฀to฀the฀
screen that you selected before entering the GID Entry
mode.
D Selecting a Home GID
The Home GID is the most often-used ID, and you can
preset it into the transceiver.
➥ Push [Home CH/GID].
฀ •฀฀You฀can฀change฀the฀Home฀GID,฀as฀described฀below.
GR
When the GID name is not programmed, the selected zone and channel number are displayed.
(example: “1- 1”)
Changing the Home GID setting:
q Select a desired GID.
w Hold down [Home CH/GID Select] for 3 seconds to
set the selected GID to the Home GID.
When using the DTMF microphone:
q Push the [0] to [9] digit keys to enter the GID Entry
mode.
CH ENTER MOD
CH No.
_ 1
w Enter the GID number, and then push [#].
฀ •฀฀Push฀[M] to delete the entered number.
฀ •฀฀Push฀ [M] again to cancel the entry, and return to the
screen that you selected before entering the GID Entry
mode.
GR
• When the GID name is not programmed, the selected zone and channel number are displayed.
(example: “1- 1”)
• When less than 9 GIDs are programmed in the zone,
you can select a GID without pushing [#] in step w.
7-3
7
NXDN OPERATION 
Transmitting a call
D Group฀call฀(Transmission฀Trunked)
When you select an NXDN Trunking System zone and
a desired GID, you can transmit a Group call by simply
pushing [PTT].
When you set GID to “ALL,” you can call all transceivers.
➥ Push [PTT] to make a Group call.
For your reference:
When฀ [Group฀ +฀ SDM฀ (NXDN)]฀ or฀ [Group฀ +฀ Status฀
(NXDN)] is assigned, you can also send a message
along with a Group call.
To send a Short Data Message along with a Group
call.
q ฀Push฀[Group฀+฀SDM฀(NXDN)]฀to฀enter฀the฀GID฀Select mode.
To send a Status Message with a Group call.
q ฀Push฀[Group฀+฀Status฀(NXDN)]฀to฀enter฀the฀GID฀Select mode.
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired GID.
e Push [P1](ENT).
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired GID.
e Push [P1](ENT).
฀ •฀Enters฀the฀Status฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to select a desired status
message.
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
STATUS
STATUS 001
t Push [P3](TX) or [PTT] to send the message to the
selected GID.
y Push [P1](EXIT) to exit.
SHORT MESSAG
y Push [PTT] to send the message to the selected
GID.
u Push [P1](EXIT) to exit.
7-4
7
NXDN OPERATION 
Transmitting a call (Continued)
D Individual฀call฀(Transmission฀Trunked)
You can call a specified station that is set to the same
unit ID by using the Individual call function.
q Push [Individual (NXDN)] to enter the Unit ID Select
mode.
฀ •฀Displays฀“SELCALL.”
SELCALL
UID 0001
w Push [UP] or [DOWN] to select a desired unit ID.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
e Push [P3](TX) or [PTT] to make an Individual call.
r Push [P1](EXIT) to exit.
For your reference:
When฀[Individual฀+฀SDM฀(NXDN)]฀or฀[Individual฀+฀Status (NXDN)] is assigned, you can also send a message along with an Individual call.
To send a Short Data Message along with an Individual call.
q ฀Push฀[Individual฀+฀SDM฀(NXDN)]฀to฀enter฀the฀unit฀ID฀
Select mode.
To send a Status Message with an Individual call.
q ฀Push฀[Individual฀+฀Status฀(NXDN)]฀to฀enter฀the฀unit฀
ID Select mode.
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired unit ID.
e Push [P1](ENT).
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired unit ID.
e Push [P1](ENT).
฀ •฀Enters฀the฀Status฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to select a desired status
message.
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
STATUS
STATUS 001
t Push [P3](TX) or [PTT] to send the message to the
selected unit ID.
y Push [P1](EXIT) to exit.
SHORT MESSAG
y Push [PTT] to send the message to the selected
unit ID.
u Push [P1](EXIT) to exit.
7-5
7
NXDN OPERATION 
Transmitting a call (Continued)
D Group฀call฀(Message฀Trunked)
D Individual฀call฀(Message฀Trunked)
When the Trunking type is set to “Message Trunked,”
and after making a Group call, the transceiver continues to be linked to the traffic channel for a preset time
period.
While linked, the transceivers occupy the traffic channel, and you can call by simply pushing [PTT].
When the Trunking type is set to “Message Trunked,”
and after making an Individual call, the transceiver continues to be linked to the traffic channel for a preset
time period.
While linked, the transceivers occupy the traffic channel, and you can call by simply pushing [PTT].
When you select the NXDN Trunking System zone and
a desired GID, you can transmit a Group call by simply
pushing [PTT].
When you set GID to “ALL,” you can call all transceivers.
q Push [Individual (NXDN)] to enter the Unit ID Select
mode.
฀ •฀Displays฀“SELCALL.”
SELCALL
UID 0001
➥ Push [PTT] to make a Group call.
w Push [UP] or [DOWN] to select the desired unit ID.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
e Push [P3](TX) or [PTT] to make an Individual call.
r Push [P1](EXIT).
For your reference:
When฀ [Group฀ +฀ SDM฀ (NXDN)]฀ or฀ [Group฀ +฀ Status฀
(NXDN)] is assigned, you can send a message along
with a Group call. See page 7-4 for details.
For your reference:
When฀[Individual฀+฀SDM฀(NXDN)]฀or฀[Individual฀+฀Status (NXDN)] is assigned, you can send a message
along with an Individual call. See page 7-5 for details.
7-6
7
NXDN OPERATION 
Transmitting a call (Continued)
D Broadcast Group call
D Status call
When you use the Broadcast Group call function, you
can transmit a signal to transceivers that are set to the
same Group ID.
When you set GID to “ALL,” you can make the Broadcast Group call to all transceivers.
The Status call is a simple message function to transmit and receive a status message. A transceiver can
display the status message quickly. You cannot transmit
a voice signal at the same time.
q Push [Status (NXDN)] to enter the Status Message
Select mode.
q Select a desired GID. (p. 7-3)
w Push [Broadcast] once or twice to select “BRDCAST
ON.”
฀ •฀Displays฀“STATUS.”
w Push [UP] or [DOWN] to select a desired status
message.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
BRDCAST ON
e Push [PTT] to make a Broadcast Group call.
STATUS
STATUS 001
e Push [P3](TX) or [PTT] to send the selected Status
Message.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
7-7
7
NXDN OPERATION 
Transmitting a call (Continued)
D Short Data call
D Long Data call
You can send a Short Data message of up to 100 characters.
If you turn OFF the transceiver’s power, the message
is cleared.
You can send a Long Data message of up to 4,096
characters only by using an external device, such as a
PC. You cannot send a Long Data message by pushing
[PTT].
q Push [SDM (NXDN)] to enter the Short Data Message Entry mode.
฀ •฀Displays฀“MESSAGE?”.
MESSAGE?
w Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
e Repeat step w until you enter a message of up to
100 characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
SHORT MESSAG
e Push [PTT] to send.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
r Push [P1](EXIT) to exit.
If you exit from the Short Data Message Entry mode,
and then you want to send the message again, do the
following steps.
q Push [SDM (NXDN)] to enter the Short Data Message Entry mode.
฀ •฀Displays฀the฀entered฀message.
฀ •฀฀Displays฀the฀last฀part฀of฀the฀message฀if฀the฀message฀is฀
over 12 characters.
HORT MESSAGE
w Push [PTT] to send.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
e Push [P1](EXIT) to exit.
7-8
7
NXDN OPERATION 
Transmitting a call (Continued)
D Telephone call
If you use the Telephone Call function, you can communicate with a telephone through the telephone lines
(PSTN, PABX, and so on).
You can call from a transceiver to a telephone, or call
from a telephone to a transceiver.
q Push [Autodial].
฀ •฀The฀irst฀entry฀in฀the฀Autodial฀list฀appears.
w Push [UP] or [DOWN] to select your desired telephone number.
e Push [P3](TX) or [PTT] to start a Telephone call
฀ •฀Displays฀“CALLING.”
฀ •฀฀Displays฀“PHONE฀CALL”฀when฀the฀transceiver฀connects฀
to the telephone line.
Displays “INVALID” when the transceiver cannot connect
to the line.
r Hold down [PTT] to talk.
t The telephone line will disconnect when you push
[R] or microphone’s [M], or when the microphone is
on-hook (depending on the presetting).
7-9
7
NXDN OPERATION 
Receiving a call
D Group call
D Individual call
When you receive a Group call that includes a matched
GID, your transceiver informs you of the call by sounding beeps and blinking “ ” on the function display. In
addition, you can easily call back to the calling station.
When you receive an Individual call that includes your
unit ID, your transceiver informs you of the call by
sounding beeps and blinking “ ” on the function display. In addition, you can easily call back to the calling
station.
q When you receive a Group call that includes a
matched GID:
q When you receive an Individual call that includes
your unit ID:
฀ •฀Beeps฀sound.
฀ •฀Displays฀the฀caller’s฀unit฀ID฀and฀GID.
฀ •฀“ ” blinks for about 10 seconds.
฀ •฀Beeps฀sound.
฀ •฀Displays฀the฀caller’s฀unit฀ID.*
*Alternately displays the caller’s unit ID and “INCOMING,”
when you receive a “Message Trunked” type call, and
the Automatic Response function is OFF.
฀ •฀“ ” blinks for about 10 seconds.
UID 0001
GID 0002
w To call back to the caller station, push [PTT] while
“ ” is blinking.
UID 0001
w To call back to the caller station, push [PTT] while
“ ” is blinking.
7-10
7
NXDN OPERATION 
Receiving a call (Continued)
D Broadcast Group call
D Status call
When a Broadcast Group Call is made, the transceivers with the same selected Group ID will receive the
call.
You cannot transmit a reply to the calling transceiver.
When your transceiver receives a Broadcast Group
Call, beeps sound.
While your transceiver is receiving the call, the musical
tone icon blinks on the function display.
When you receive a Status call, your transceiver displays a received status message on the function display.
The received message is stored in the Memory Stack,
and you can view the message contents in the memory.
(p. 6-3)
➥ When you receive a Status call:
฀ •฀Beeps฀sound.
฀ •฀฀Displays฀“DATA฀RCVD,”฀“COMPLETE,”฀the฀received฀message, the caller’s unit ID and GID*.
*Displayed only when the received call is a Group call.
฀ •฀“ ” blinks on the function display.
The message is stored in the Memory Stack.
COMPLETE
STATUS 001
UID 0001
GID 0002
7-11
7
NXDN OPERATION 
Receiving a call (Continued)
D Short Data call
D Long Data call
When you receive a Short Data message, your transceiver displays the message on the function display.
The message is stored in the Memory Stack, and you
can view the message in the memory. (p. 6-3)
You can receive a Long Data message of up to 4,096
characters. The message can be output to a PC or external device from your transceiver.
➥ When you receive a Short Data message:
฀ •฀Beeps฀sound.
฀ •฀฀Displays฀“DATA฀RCVD,”฀“COMPLETE,”฀the฀received฀message, the caller’s unit ID and GID*.
*Displayed only when the received call is the Group call.
฀ •฀“ ” blinks on the function display.
The message is stored in the Memory Stack.
DATA RCVD
COMPLETE
SHORT MESSAG
Scrolls when the received message is
over 12 characters.
UID 0001
GID 0002
7-12
7
NXDN OPERATION 
Receiving a call (Continued)
D Telephone call
When you receive a call from a telephone, you can communicate with it through the telephone lines (PSTN,
PABX, and so on).
When a telephone calls your transceiver, the transceiver sounds beeps, and then “PHONE” is displayed on
the function display.
Hold down [PTT] to talk to the telephone.
7-13
7
NXDN OPERATION 
Forced Search
If you use the Forced Search function, the transceiver
searches for other Control channels using the following
hunt sequences.
Hunt sequence
Preferential Hunt Sequence
Normal Hunt Sequence
System Add Channel Sequence
Site Hunt Sequence
Comprehensive Hunt Sequence
Explanation
The transceiver searches for a Control channel that is set as the
Preferential Hunt Control channel.
The transceiver selects this Control channel with a high priority.
The transceiver searches for a Control channel that is set as the
Normal Hunt Control channel.
The transceiver searches for up to 8 Control channels that are
added by the system.
The transceiver searches for a Control channel that is set as the
Site Hunt Control channel in each site.
The transceiver searches for a Control channel that is set in the
network frequency table.
q Hold down [Forced Search Function] for 2 seconds
to turn ON the Forced Search Function.
฀ •฀Displays฀the฀current฀site฀number.
w The transceiver starts to search for a Control channel signal.
฀ •฀Displays฀“SEARCHING.”
e When the transceiver finds and registers to a control
channel, the normal screen is displayed on the function display.
7-14
Section 8
NXDN OPERATION 
NXDN Conventional operation ...............................................8-2
Transmitting a call ...................................................................8-3
Group call ................................................................................8-3
Individual call ...........................................................................8-4
Individual Call Acknowledge Request call ...............................8-4
Status call ................................................................................8-5
Short Data call.........................................................................8-5
Long Data call .........................................................................8-5
Receiving a call........................................................................8-6
Group call ................................................................................8-6
Individual call ...........................................................................8-6
Individual Call Acknowledge Request call ...............................8-7
Status call ................................................................................8-7
Short Data call.........................................................................8-8
Long Data Call.........................................................................8-8
Mixed Mode ..............................................................................8-9
8-1
8
NXDN OPERATION 
NXDN Conventional operation
When you select the NXDN Conventional system
mode, you must manually search for and select a clear
channel.
The system setup is easier than the Trunking mode.
8-2
8
NXDN OPERATION 
Transmitting a call
D Group call
When you select the NXDN Conventional System zone,
you can make a Group call by using the Group Call
function.
Set GID to “ALL,” to call all transceivers.
q Push [Group (NXDN)] to enter the GID Select mode.
฀ •฀Displays฀“SELCALL.”
SELCALL
GID 0001
w Push [P2](Ω) or [P3](≈) to select the desired GID.
e Push [PTT] to make a Group call.
r Push [P1](EXIT).
For your reference:
When฀ [Group฀ +฀ SDM฀ (NXDN)]฀ or฀ [Group฀ +฀ Status฀
(NXDN)] is assigned, you can send a message along
with a Group call.
To send a Short Data Message with a Group call.
q ฀Push฀[Group฀+฀SDM฀(NXDN)]฀to฀enter฀the฀GID฀Select mode.
To send a Status Message with a Group call.
q ฀Push฀[Group฀+฀Status฀(NXDN)]฀to฀enter฀the฀GID฀Select mode.
฀ •฀Displays฀“SELCALL.”
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired GID.
e Push [P1](ENT).
w Push [UP] or [DOWN] to select a desired GID.
e Push [P1](ENT).
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
฀ •฀Enters฀the฀Status฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
r Push [UP] or [DOWN] to select a desired status
message.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
STATUS
STATUS 001
SHORT MESSAG
t Push [P3](TX) or [PTT] to send the message to the
selected GID.
y Push [P1](EXIT) to exit.
y Push [PTT] to send the message to the selected
GID.
u Push [P1](EXIT) to exit.
8-3
8
NXDN OPERATION 
Transmitting a call (Continued)
D Individual call
D Individual Call Acknowledge Request call
You can call a specified station that is set to the same
unit ID by using the Individual call function.
When the Individual Call Acknowledge Request function is set, you can transmit an acknowledgement request signal with the Individual call.
Therefore, you can confirm whether the transceiver is
located in the communication range or not.
q Push [Individual (NXDN)] to enter the Unit ID Select
mode.
฀ •฀Displays฀“SELCALL.”
q Push [Individual (NXDN)] to enter the Unit ID Select
mode.
SELCALL
UID 0001
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired unit ID.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
w Push [UP] or [DOWN] to select a desired unit ID.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀an฀unit฀ID,฀push฀[P2](MODE)฀
to select the Unit ID Entry mode.
You can enter an unit ID between 1 and 65519.
e Push [P3](TX) or [PTT] to make the Individual call
with an acknowledgement request signal.
e Push [P3](TX) or [PTT] to make the Individual call.
r Push [P1](EXIT).
฀ •฀฀Displays฀“CALLING,”฀and฀then฀after฀receiving฀an฀acknowledgement, displays “HOLDING.”
r When the called station calls back, the transceiver
displays the called station’s unit ID.
฀ •฀฀Displays฀“NO฀REPLY”฀and฀sounds฀error฀beeps฀when฀your฀
transceiver does not receive an acknowledgement within
the preset time period.
For your reference:
When฀[Individual฀+฀SDM฀(NXDN)]฀or฀[Individual฀+฀Status (NXDN)] is assigned, you can send a message
along with an Individual call.
To send a Short Data Message with an Individual call.
q ฀Push฀[Individual฀+฀SDM฀(NXDN)]฀to฀enter฀the฀unit฀ID฀
Select mode.
To send a Status Message with an Individual call.
q ฀Push฀[Individual฀+฀Status฀(NXDN)]฀to฀enter฀the฀unit฀
ID Select mode.
฀ •฀Displays฀“SELCALL.”
฀ •฀Displays฀“SELCALL.”
w Push [UP] or [DOWN] to select a desired unit ID.
e Push [P1](ENT).
w Push [UP] or [DOWN] to select a desired unit ID.
e Push [P1](ENT).
฀ •฀Enters฀the฀Short฀Data฀Message฀Entry฀mode.
฀ •฀Enters฀the฀Status฀Message฀Entry฀mode.
r Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
r Push [UP] or [DOWN] to select a desired status
message.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
t Repeat step r until you enter a message of up to
100 characters.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
STATUS
STATUS 001
SHORT MESSAG
t Push [P3](TX) or [PTT] to send the message to the
selected unit ID.
y Push [P1](EXIT) to exit.
y Push [PTT] to send the message to the selected
unit ID.
u Push [P1](EXIT) to exit.
8-4
8
NXDN OPERATION 
Transmitting a call (Continued)
D Status call
D Short Data call
The status call is a simple message function to transmit
and receive a status message. A transceiver can display the status message quickly. You cannot transmit a
voice signal at the same time.
You can send a Short Data message of up to 100 characters.
If you turn OFF the transceiver’s power, the message
is cleared.
q Push [Status (NXDN)] to enter the Status Message
Select mode.
q Push [SDM (NXDN)] to enter the Short Data Message Entry mode.
฀ •฀Displays฀“STATUS.”
฀ •฀Displays฀“MESSAGE?”.
w Push [UP] or [DOWN] to select a desired status
message.
MESSAGE?
฀ •฀฀If฀you฀want฀to฀directly฀enter฀a฀status฀message,฀push฀[P2]
(MODE) to select the Status Message Entry mode.
You can enter a status message between 1 and 207.
฀ •฀฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
w Push [UP] or [DOWN] to enter a character, and then
push [P1](SET) to set.
฀ •฀Goes฀to฀the฀next฀character฀entry฀position.
฀ •฀You฀can฀use฀the฀10-keypad฀keys฀on฀the฀microphone.
STATUS
STATUS 001
e Repeat step w until you enter a message of up to
100 characters.
e Push [P3](TX) or [PTT] to send the selected Status
Message.
฀ •฀Push฀[P0](DEL)฀to฀delete฀a฀character.
฀ •฀฀Push฀[P2](Ω) or [P3](≈) left or right to select a character.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
SHORT MESSAG
r Push [PTT] to send.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
t Push [P1](EXIT) to exit.
If you exit from the Short Data Message Entry mode,
and then you want to transmit the message again, do
the following steps.
q Push [SDM (NXDN)] to enter the Short Data Message Entry mode.
฀ •฀Displays฀the฀entered฀message.
฀ •฀฀Displays฀the฀last฀part฀of฀the฀message฀if฀the฀message฀is฀
over 12 characters.
HORT MESSAGE
w Push [PTT] to send.
฀ •฀฀Displays฀“SEND฀DATA”฀and฀then฀“COMPLETE.”
e Push [P1](EXIT) to exit.
D Long Data call
You can send a Long Data message of up to 4,096
characters only by using an external device, such as a
PC. You cannot send a message by pushing [PTT].
8-5
8
NXDN OPERATION 
Receiving a call
D Group call
D Individual call
When you receive a Group call that includes a matched
GID, your transceiver informs you the calling by sounding beeps and blinking “ ” on the function display. In
addition, you can easily call back to the calling station.
When you receive an Individual call that includes your
unit ID, your transceiver informs you the calling by
sounding beeps and blinking “ ” on the function display. In addition, you can easily call back to the calling
station.
q When you receive a Group call that includes a
matched GID:
q When you receive an Individual call that includes
your unit ID:
฀ •฀Beeps฀sound.
฀ •฀Displays฀the฀caller’s฀unit฀ID฀and฀GID.
฀ •฀“ ” blinks for about 10 seconds.
฀ •฀Beeps฀sound.
฀ •฀Displays฀the฀caller’s฀unit฀ID.
฀ •฀“ ” blinks for about 10 seconds.
UID 0001
GID 0002
UID 0001
w To call back to the caller station, push [PTT] while
“ ” is blinking.
w To call back to the caller station, push [PTT] while
“ ” is blinking.
8-6
8
NXDN OPERATION 
Receiving a call (Continued)
D Individual Call Acknowledge Request call
D Status call
When you receive an Individual Call with an acknowledgement request which includes your own Individual
ID, your transceiver automatically transmits a acknowledgement signal, and informs you the calling by beep
sounds and bell mark blinks on the function display. In
addition, you can easily call back to the calling transceiver.
When you receive a Status call, your transceiver displays a received status message on the function display.
The received message is stored in the Memory Stack,
and you can view the message contents in the memory.
(p. 6-3)
➥ When you receive a Status call:
฀ •฀Beeps฀sound.
฀ •฀฀Displays฀“DATA฀RCVD,”฀“COMPLETE,”฀the฀received฀message, the caller’s unit ID and GID*.
*Displayed only when the received call is the Group call.
฀ •฀“ ” blinks on the function display.
The message is stored in the Memory Stack.
q When you receive an Individual call with an acknowledgement request signal that includes your unit ID:
฀ •฀Beeps฀sound.
฀ •฀฀Alternately฀displays฀the฀caller’s฀unit฀ID฀and฀“INCOMING.”
฀ •฀“ ” blinks for about 30 seconds.
w To call back to the caller station, push [PTT] while
“ ” is blinking.
COMPLETE
STATUS 001
UID 0001
GID 0002
8-7
8
NXDN OPERATION 
Receiving a call (Continued)
D Short Data call
D Long Data Call
When you receive a Short Data message, your transceiver displays the message on the function display.
The message is also stored in the Memory Stack, and
you can view the message in the memory. (p. 6-3)
You can receive a Long Data message of up to 4,096
characters. The message can be output to a PC or external device from your transceiver.
➥ When you receive a Short Data message:
฀ •฀Beeps฀sound.
฀ •฀฀Displays฀“DATA฀RCVD,”฀“COMPLETE,”฀the฀received฀message, the caller’s unit ID and GID*.
*Displayed only when the received call is the Group call.
฀ •฀“ ” blinks on the function display.
The message is stored in the Memory Stack.
DATA RCVD
COMPLETE
SHORT MESSAG
Scrolls when the received message is
over 12 characters.
UID 0001
GID 0002
8-8
8
NXDN OPERATION 
Mixed Mode
If you set your transceiver to the Mixed mode, you can
receive both digital and analog signals. You can use a
digital transceiver on analog channels, therefore you
can easy switch from an analog system to a digital system.
8-9
A-7148-3EX
© 2014 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Author                          : Icom Inc.
Create Date                     : 2014:05:30 11:32:18+09:00
Modify Date                     : 2014:07:09 15:19:29-04:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2014:07:09 15:19:29-04:00
Creator Tool                    : Adobe InDesign CS3_J (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7026 bytes, use -b option to extract)
Instance ID                     : uuid:7caccef1-428f-44c4-94d6-2d57c27998aa
Document ID                     : adobe:docid:indd:17e32df4-e15d-11e3-ba42-bf1ea744c506
Rendition Class                 : proof:pdf
Derived From Instance ID        : 5f230a33-e141-11e3-94e6-8c2ccb00e295
Derived From Document ID        : adobe:docid:indd:1cdf2da0-d18d-11e3-93e7-c04fb228c3a5
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:B27943B3A2BFE311B2B0F473CC11A7E8, uuid:509E5CE51BC1E311A31AB7874F0C4C0A, uuid:B27943B3A2BFE311B2B0F473CC11A7E8, uuid:0EA67789BCD5E311B7D6C7258B4D8126, uuid:11A67789BCD5E311B7D6C7258B4D8126, uuid:7415702016D7E3119224ECEC20D521C2, uuid:61C24B77B6D5E311B7D6C7258B4D8126, uuid:61C24B77B6D5E311B7D6C7258B4D8126, uuid:70EA640AFDDAE311B0ECD90D4879E611, uuid:7415702016D7E3119224ECEC20D521C2, uuid:6FEA640AFDDAE311B0ECD90D4879E611, uuid:7415702016D7E3119224ECEC20D521C2, uuid:246D296018D7E3119224ECEC20D521C2, uuid:276D296018D7E3119224ECEC20D521C2, uuid:77EA640AFDDAE311B0ECD90D4879E611, uuid:2C6D296018D7E3119224ECEC20D521C2, uuid:61C24B77B6D5E311B7D6C7258B4D8126, uuid:71EA640AFDDAE311B0ECD90D4879E611, uuid:17E881B32ED7E3119224ECEC20D521C2, uuid:1BE881B32ED7E3119224ECEC20D521C2, uuid:1EE881B32ED7E3119224ECEC20D521C2, uuid:459551792FD7E3119224ECEC20D521C2, uuid:479551792FD7E3119224ECEC20D521C2, uuid:72EA640AFDDAE311B0ECD90D4879E611, uuid:71EA640AFDDAE311B0ECD90D4879E611, uuid:73EA640AFDDAE311B0ECD90D4879E611, uuid:4E9551792FD7E3119224ECEC20D521C2, uuid:87E9DC0831D7E3119224ECEC20D521C2, uuid:74EA640AFDDAE311B0ECD90D4879E611, uuid:8DE9DC0831D7E3119224ECEC20D521C2, uuid:305522E334D7E3119224ECEC20D521C2, uuid:75EA640AFDDAE311B0ECD90D4879E611, uuid:61C24B77B6D5E311B7D6C7258B4D8126, uuid:355522E334D7E3119224ECEC20D521C2, uuid:375522E334D7E3119224ECEC20D521C2, uuid:76EA640AFDDAE311B0ECD90D4879E611, uuid:2B04460E38D7E3119224ECEC20D521C2, uuid:2F04460E38D7E3119224ECEC20D521C2, uuid:002984B84ADAE31196518F1A9B4A173B, uuid:246D296018D7E3119224ECEC20D521C2, uuid:276D296018D7E3119224ECEC20D521C2, uuid:77EA640AFDDAE311B0ECD90D4879E611, uuid:8564316B9BDCE311A80CA26C7FCC9A24, uuid:8864316B9BDCE311A80CA26C7FCC9A24, uuid:8B64316B9BDCE311A80CA26C7FCC9A24, uuid:70EA640AFDDAE311B0ECD90D4879E611, uuid:9DA1DF57A2DCE311A80CA26C7FCC9A24, uuid:6FEA640AFDDAE311B0ECD90D4879E611, uuid:9DA1DF57A2DCE311A80CA26C7FCC9A24, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A22FC2B2F7DEE311977D827A20A74438, uuid:A12FC2B2F7DEE311977D827A20A74438, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A22FC2B2F7DEE311977D827A20A74438, uuid:A12FC2B2F7DEE311977D827A20A74438, uuid:E6B58455B1DCE311A80CA26C7FCC9A24, uuid:E9B58455B1DCE311A80CA26C7FCC9A24, uuid:ECB58455B1DCE311A80CA26C7FCC9A24, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:EFB58455B1DCE311A80CA26C7FCC9A24, uuid:BFBC27DFB2DCE311A80CA26C7FCC9A24, uuid:BCBC27DFB2DCE311A80CA26C7FCC9A24, uuid:189B9FABB5DCE311A80CA26C7FCC9A24, uuid:159B9FABB5DCE311A80CA26C7FCC9A24, uuid:149B9FABB5DCE311A80CA26C7FCC9A24, uuid:189B9FABB5DCE311A80CA26C7FCC9A24, uuid:159B9FABB5DCE311A80CA26C7FCC9A24, uuid:97D07FD9B6DCE311A80CA26C7FCC9A24, uuid:1B9B9FABB5DCE311A80CA26C7FCC9A24, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A22FC2B2F7DEE311977D827A20A74438, uuid:A62FC2B2F7DEE311977D827A20A74438, uuid:A12FC2B2F7DEE311977D827A20A74438, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A22FC2B2F7DEE311977D827A20A74438, uuid:E9B58455B1DCE311A80CA26C7FCC9A24, uuid:ECB58455B1DCE311A80CA26C7FCC9A24, uuid:A0A1DF57A2DCE311A80CA26C7FCC9A24, uuid:EFB58455B1DCE311A80CA26C7FCC9A24, uuid:BFBC27DFB2DCE311A80CA26C7FCC9A24, uuid:BCBC27DFB2DCE311A80CA26C7FCC9A24, uuid:189B9FABB5DCE311A80CA26C7FCC9A24, uuid:159B9FABB5DCE311A80CA26C7FCC9A24, uuid:149B9FABB5DCE311A80CA26C7FCC9A24, uuid:189B9FABB5DCE311A80CA26C7FCC9A24, uuid:159B9FABB5DCE311A80CA26C7FCC9A24, uuid:97D07FD9B6DCE311A80CA26C7FCC9A24, uuid:1B9B9FABB5DCE311A80CA26C7FCC9A24
Manifest Reference Document ID  : uuid:AC7943B3A2BFE311B2B0F473CC11A7E8, uuid:200848806EC0E311A579B4C2089AA01E, uuid:AC7943B3A2BFE311B2B0F473CC11A7E8, uuid:0BA67789BCD5E311B7D6C7258B4D8126, uuid:10A67789BCD5E311B7D6C7258B4D8126, uuid:7BB3DC27BED5E311B7D6C7258B4D8126, uuid:5BC24B77B6D5E311B7D6C7258B4D8126, uuid:5BC24B77B6D5E311B7D6C7258B4D8126, uuid:7815702016D7E3119224ECEC20D521C2, uuid:7BB3DC27BED5E311B7D6C7258B4D8126, uuid:7515702016D7E3119224ECEC20D521C2, uuid:7BB3DC27BED5E311B7D6C7258B4D8126, uuid:7B15702016D7E3119224ECEC20D521C2, uuid:256D296018D7E3119224ECEC20D521C2, uuid:286D296018D7E3119224ECEC20D521C2, uuid:2A6D296018D7E3119224ECEC20D521C2, uuid:5BC24B77B6D5E311B7D6C7258B4D8126, uuid:2D6D296018D7E3119224ECEC20D521C2, uuid:16E881B32ED7E3119224ECEC20D521C2, uuid:18E881B32ED7E3119224ECEC20D521C2, uuid:1CE881B32ED7E3119224ECEC20D521C2, uuid:1FE881B32ED7E3119224ECEC20D521C2, uuid:469551792FD7E3119224ECEC20D521C2, uuid:489551792FD7E3119224ECEC20D521C2, uuid:2D6D296018D7E3119224ECEC20D521C2, uuid:4A9551792FD7E3119224ECEC20D521C2, uuid:4D9551792FD7E3119224ECEC20D521C2, uuid:85E9DC0831D7E3119224ECEC20D521C2, uuid:88E9DC0831D7E3119224ECEC20D521C2, uuid:8BE9DC0831D7E3119224ECEC20D521C2, uuid:8EE9DC0831D7E3119224ECEC20D521C2, uuid:315522E334D7E3119224ECEC20D521C2, uuid:5BC24B77B6D5E311B7D6C7258B4D8126, uuid:345522E334D7E3119224ECEC20D521C2, uuid:365522E334D7E3119224ECEC20D521C2, uuid:385522E334D7E3119224ECEC20D521C2, uuid:2A04460E38D7E3119224ECEC20D521C2, uuid:2C04460E38D7E3119224ECEC20D521C2, uuid:CB55773237C5E311A800E5A2E1CDFEC6, uuid:7B15702016D7E3119224ECEC20D521C2, uuid:256D296018D7E3119224ECEC20D521C2, uuid:286D296018D7E3119224ECEC20D521C2, uuid:86BB5BE60DC9E311A34397BED5BCDB8D, uuid:8664316B9BDCE311A80CA26C7FCC9A24, uuid:8964316B9BDCE311A80CA26C7FCC9A24, uuid:7815702016D7E3119224ECEC20D521C2, uuid:8C64316B9BDCE311A80CA26C7FCC9A24, uuid:7515702016D7E3119224ECEC20D521C2, uuid:8C64316B9BDCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:A1A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A4A1DF57A2DCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:A1A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A4A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A6A1DF57A2DCE311A80CA26C7FCC9A24, uuid:E7B58455B1DCE311A80CA26C7FCC9A24, uuid:EAB58455B1DCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:EDB58455B1DCE311A80CA26C7FCC9A24, uuid:BDBC27DFB2DCE311A80CA26C7FCC9A24, uuid:F0B58455B1DCE311A80CA26C7FCC9A24, uuid:169B9FABB5DCE311A80CA26C7FCC9A24, uuid:C3BC27DFB2DCE311A80CA26C7FCC9A24, uuid:129B9FABB5DCE311A80CA26C7FCC9A24, uuid:169B9FABB5DCE311A80CA26C7FCC9A24, uuid:C3BC27DFB2DCE311A80CA26C7FCC9A24, uuid:1C9B9FABB5DCE311A80CA26C7FCC9A24, uuid:199B9FABB5DCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:A1A1DF57A2DCE311A80CA26C7FCC9A24, uuid:A32FC2B2F7DEE311977D827A20A74438, uuid:A4A1DF57A2DCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:A1A1DF57A2DCE311A80CA26C7FCC9A24, uuid:E7B58455B1DCE311A80CA26C7FCC9A24, uuid:EAB58455B1DCE311A80CA26C7FCC9A24, uuid:9EA1DF57A2DCE311A80CA26C7FCC9A24, uuid:EDB58455B1DCE311A80CA26C7FCC9A24, uuid:BDBC27DFB2DCE311A80CA26C7FCC9A24, uuid:F0B58455B1DCE311A80CA26C7FCC9A24, uuid:169B9FABB5DCE311A80CA26C7FCC9A24, uuid:C3BC27DFB2DCE311A80CA26C7FCC9A24, uuid:129B9FABB5DCE311A80CA26C7FCC9A24, uuid:169B9FABB5DCE311A80CA26C7FCC9A24, uuid:C3BC27DFB2DCE311A80CA26C7FCC9A24, uuid:1C9B9FABB5DCE311A80CA26C7FCC9A24, uuid:199B9FABB5DCE311A80CA26C7FCC9A24
Format                          : application/pdf
Creator                         : Icom Inc.
Title                           : IC-F5360D/F6360D Operating Instructions
Light Source                    : Unknown
Startup Profile                 : Print
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Mode                       : UseOutlines
Page Count                      : 67

EXIF Metadata provided by EXIF.tools

ICOM orporated 366400 VHF Digital Transceiver User Manual IC F5360D F6360D Operating Instructions

ICOM Incorporated VHF Digital Transceiver IC F5360D F6360D Operating Instructions

User Manual

FCC ID Filing: AFJ366400

Navigation menu

Namespaces

Views

Navigation