ICOM orporated 374000 IP501H User Manual

ICOM Incorporated IP501H

Contents

User Manual

Download: ICOM orporated 374000 IP501H User Manual
Mirror Download [FCC.gov]ICOM orporated 374000 IP501H User Manual
Document ID3656055
Application IDOekVNQ7nMj+Sbg0khgpHvg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize187.84kB (2348020 bits)
Date Submitted2017-11-28 00:00:00
Date Available2018-05-28 00:00:00
Creation Date2017-09-01 16:11:47
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2017-09-01 16:11:50
Document TitleUser Manual
Document CreatorAdobe InDesign CS6 (Windows)

6.	STANDARD CHARGING TIME AND
BATTERY LIFE
5. ATTACHING THE BATTERY PACK
GUIDE
Follow the order (1 ~ 2) on the illustration below.
IP ADVANCED RADIO SYSTEM
Thank you for choosing the IP501H ip advanced radio
system communication terminal.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
IP501H
Battery
Spec item
After attaching, check that
the battery pack is securelly
attached.
1. SUPPLIED ACCESSORIES
• Belt clip (MB-135)………………………1
[TX/RX] indicator
[PWR/VOL]
dial
[PTT] switch
Function
screen
[Optional]
key★1
Keypad
(Refere to the
other side.)
Microphone
When connecting optional
equipment
[PWR/VOL] dial
◎B e sure to turn power
OFF before connecting
or disconnecting optional
Plug
equipment to or from the
jack.
Connector
◎Hold the plug when you
cover
remove the cable.
◎Insert the plug securely when connecting the cable.
◎CAUTION: Attach the jack cover when optional equipment is
not used.
★1	Ask for your dealer about the assigned function.
★2	While connecting an optional speaker microphone, the audio is not output from
the internal speaker.
NOTE: Instructions and screens on this guide may differ, depending on the
settings.
Speaker
3. ATTACHING THE BELT CLIP
※Remove the battery pack before attaching the belt clip.
★2
4. ATTACHING THE ANTENNA/HAND STRAP
Supplied antenna
Hold this part to turn.
Supplied belt clip
Battery pack
Slide the belt clip in the direction of the
arrow until the belt clip locks in place, and
makes a‘click’sound.
Supplied
hand strap
Charging with BC-202 or BC-211
About the remaining voltage indication
Blink
sufficient
capacity
exhausted a nearing exhaustion
little.
(Charging is necessary)
Exhausted
(Charging required)
※When the battery charge is almost exhausted, the battery status indicator,
“
,” starts blinking, and warning beeps sound every 30 seconds.
Charge the battery pack when the beeps begin to sound.
※When “LOW BATTERY” is displayed, the communication terminal power
will automatically turn OFF soon.
7. BATTERY CHARGING(Using the BC-202)
Fully charge the battery pack when fist time of use or has not
been used for more than 2 months.
WARNING! NEVER charge the communication
terminal during a lightning storm. It may result in an
electric shock, cause a fire or damage the communication
terminal. Always disconnect the power adapter
before a storm.
• Turn OFF the power before charging.
Otherwise, the battery may not be fully charged.
• Insert the communication terminal (battery attached to
the communication terminal) into the charger as shown
to the light.
• Charging indicator lights orange while charging. When
the battery pack is fully charged, lights green.
If the indicator blinks in orange, read the IP501H
instruction manual on the Icom web site.
• The charger automatically restarts charging when the
attached battery pack voltage drops.
• Disconnect the AC cable from the outlet when the
charger is not in use.
RDANGER
Lift the tab up (1), and slide the belt
clip in the direction of the arrow (2).
NOTE: Turn OFF the power before
remove the battery pack in
order (1 ~ 2) on the illustration
to the left.
TX:RX:Stand-by=5:5:90
3.5 hours (Approximately)
※The supplied battery is BP-272.
• Immediately stop using the battery if it emits an abnormal
odor, heats up, or is discolored or deformed. If any of
these conditions occur, contact your Icom dealer or
distributor.
CAUTION
Even when the communication terminal
power is OFF, a small current still flows
in the communication terminal. Remove
the battery pack or case when not
using it for a long time. Otherwise, the
batteries will become exhausted.
17 hours (Approximately)
Charging time
• Antenna…………………………………… 1
2. PANEL DESCRIPTION
BP-272
Operating time
Battery pack
• Battery pack(BP-272)…………………………………1
• Hand strap………………………………………………1
Antenna
NOTE: O
 perating time or charging time may be shorter depending
on the environment such as roaming frequency.
•	Use and charge only specified Icom battery
packs with Icom communication terminals or Icom
chargers. Only Icom battery packs are tested and
approved for use with Icom communication terminals
or charged with Icom chargers. Using thirdparty or
counterfeit battery packs or chargers may cause
smoke, fire, or cause the battery to burst.
•	Use the battery only with the communication
terminal for which it is specified. Never use a battery
with any other equipment, or for any purpose that is
not specified in this instruction manual.
•	Read "PRECAUTION" before attempt to charging
the battery pack.
Turn OFF
[Battery pack]
[Terminal+Battery pack]
AC Outlet
Tapping screw
(Purchase separately)
BC-123S
(Supplied with BC-202)
Charge indicator
Charging:Orange
Finished :Green
Optional rapid charger BC-202
About the battery life cycle
BE SURE to replace the battery pack with a new one after five
years, even if still holds a charge. The material inside the battery will
deteriorate after a period of time, even with little use. The estimated
number of times you can charge the battery is between 300 and 500.
Even when the battery appears to be fully charged, the operating
time of the communication terminal may become short when:
・ Approximately five years have passed since the battery was
manufactured.
・ The battery has been repeatedly charged.
※Instructions and screens on this guide may differ, depending on the settings.
8. TURNING ON THE POWER/ADJUSTING THE AUDIO LEVEL
11. Making a Call
Turning ON the power
Adjusting the audio output level
Turn [PWR/VOL] clockwise to set the 12 O'clock position.
 A beep sounds.
Turn [PWR/VOL] to adjust the audio output level.
Set the output to a suitable level.
•A volume level between 0 and 32 is displayed.。
※The dial is made physically tight for the dust and water resistance.
Hold down [PTT], and speak into the microphone.
 [TX/RX] indicator lights red while [PTT] is pushed.
Turn
音量:
10/4 12:57
All Call transmitting screen
Standby screen
The signal strength is represented by 3 bars indication.
In the 3G mode, the resceived signal strength is indicated by the
icon.
In the LTE mode,
icon is displayed.
※When the terminal is out of the service area, or cannot receive the signal,
(out-of-service)icon blinks.
NOTE: If the output level is set to the minimum level, the beep does not
sound.
Hold down
Microphone
Hold down
9. ABOUT THE KEY OPERATIONS
★Can be used, depending on the presetting.
[Call List address book] key★
Lights orange
全体
全体
Standby screen
*Depending on the presetting, ask your dealer for detail.
10/4 12:57
10
While receiving a call, push [PTT] to talk in the full duplex
mode*.
	In the Full Duplex mode,[TX/RX]indicator lights orange.
Lights red
Turn
[Function] key★
Selects the message to send,
Presence or Talk group.
When making a group or
individual call, select calling
party from this list.
Push this button again to switch the radio screen for
“All Call”,“Group Call” or “Individual Call” address
book.
メッセージ
Microphone
When receiving a call, [TX/RX] indicator lights green.
Lights green
Blinks when receive a Call
Turning OFF the power
10/4 12:58
全体
Turn [PWR/VOL] maximum counter
clockwise.
Turn
All Call receiving screen
個 別 00005
集合してください
個別
(Example: A message is selected.)
00001
個 別 00001
Speaker
[CLR/LOCK] key
Address book: Individual
Push to bring back normal
operating screen from a function
screen such as Call History
screen.
Hold down to turn the key lock
ON or OFF.
※[PTT] key and [PWR/VOL] dial
can be operated even while in
the Key Lock function is activated.
[Call history] key ★
Repeatedly push to select call history from the TX log,
RX log, TX MSG log, RX MSG log, TX TEL log or RX
TEL log.
• Selectable log may differ, depending on the IP1000C
settings.
• Push [Up]/[Dwn] to select a desired log.
• Hold down until “Emergency” is displayed to send an
emergency call, depending on the settings.
10/4 12:57
[▲]/[▼] key
Push to scroll the address book or
call history table.
全体
(Example: Key Lock falling munction is ON.)
10. About the Call types(Calling party)
When Address Book is activated, the radio will display calling party.
Otherwise the radio pre‐programmed calling party will be displayed.
Calling Mode Icons*
: All Group Call
: Group Call
10/4 12:57
全体
All Call screen
10/4 12:57
営業8
Individual Call Screen
: Individual Call
: Phone Call
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand and/or other countries.
*Blink when a call or message is received.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A?????-?EX
Printed in Japan
© 2017 Icom Inc.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Instance ID                     : uuid:f9c5ca9a-ff3f-4f2e-90ec-f6ed00f047b3
Original Document ID            : adobe:docid:indd:7bfce9e7-7fff-11e4-8a24-9346b18b6229
Document ID                     : xmp.id:3D2037C9E48EE711928CBABE95BD34C5
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:3C2037C9E48EE711928CBABE95BD34C5
Derived From Document ID        : xmp.did:53C2E058DE78E711AE12E030A0CF4BCB
Derived From Original Document ID: adobe:docid:indd:7bfce9e7-7fff-11e4-8a24-9346b18b6229
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2017:09:01 16:11:47+09:00
Metadata Date                   : 2017:09:01 16:11:50+09:00
Modify Date                     : 2017:09:01 16:11:50+09:00
Create Date                     : 2017:09:01 16:11:47+09:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS6 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AFJ374000

Navigation menu