ICOM orporated 382200 VHF Marine Transceiver User Manual IC M93D M93D EURO 0
ICOM Incorporated VHF Marine Transceiver IC M93D M93D EURO 0
User Manual
INSTRUCTION MANUAL VHF MARINE TRANSCEIVER iM93D iM93D EURO This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Thank you for choosing this Icom product. This product is designed and built with Icom’ s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. z Floats on water IMPORTANT z Floats and lashes READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL—This instruction manual contains important operating instructions for the IC-M93D and IC-M93D EURO. This instruction manual includes some functions which are usable only when they are preset by your dealer. Ask your dealer for details. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: • Force majeure, including, but not limited to, ires, earthquakes, storms, loods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. • The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. FEATURES The transceiver loats in fresh or salt water even when the supplied accessories are attached. • It may sink when a third-party accessory is attached. When the transceiver detects that it has come in contact with water, the backlight starts to blink, making it easy to ind the transceiver even at night or in a dark environment. z Wide screen and easy user interface The transceiver is equipped with a wide screen for easy readability and easy-to-use user interface. z Dualwatch and Tri-watch functions Convenient functions that enable you to monitor the Distress channel (Ch 16) while receiving on another channel of your choice (Dualwatch), or while receiving on another channel of your choice, and the Call channel (Tri-watch). * May not be usable depending on the transceiver version. EXPLICIT DEFINITIONS WORD DEFINITION RDANGER! Personal death, serious injury or an explosion may occur. RWARNING! CAUTION NOTE Personal injury, ire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, ire or electric shock. IN CASE OF EMERGENCY If your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on Channel 16. Or, transmit your Distress call using Digital Selective Calling (DSC) on Channel 70. USING CHANNEL 16 DISTRESS CALL PROCEDURE USING DIGITAL SELECTIVE CALLING (Ch 70) DISTRESS CALL PROCEDURE 1. “MAYDAY MAYDAY MAYDAY.” 2. “THIS IS ...............” (name of vessel). 3. Say your call sign or other indication of the vessel (AND your 9 digit DSC ID, if you have one). 4. “LOCATED AT ...............” (your position). 5. State the nature of the distress and assistance required. 6. Give any other information which might facilitate the rescue. 1. While lifting up the key cover, hold down [DISTRESS] for 3 seconds until you hear 3 short beeps and then one long beep. 2. Wait for an acknowledgment on Channel 70 from a coast station. • After the acknowledgement is received, Channel 16 is automatically selected. 3. Hold down [PTT], then transmit the appropriate information as listed to the left. Key cover ii PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. Shorting may occur if the terminals touch metal objects such as a key, so be careful when placing the battery packs (or the transceiver) in bags, and so on. Carry them so that shorting cannot occur with metal objects. Shorting may damage not only the battery pack, but also the transceiver. R DANGER! NEVER operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. R DANGER! NEVER use and charge Icom battery packs with non-Icom transceivers or non-Icom chargers. Only Icom battery packs are tested and approved for use with Icom transceivers or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, ire, or cause the battery to burst. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. The continuous high volume operation may cause a ringing in your ears. If you experience the ringing, reduce the volume level or discontinue use. CAUTION: DO NOT use harsh solvents such as Benzine or alcohol when cleaning, because they will damage the transceiver surfaces. iii CAUTION: DO NOT attach the battery unless the lexible antenna, battery pack and jack cover are securely attached to the transceiver. Conirm that the antenna and battery pack are dry before attaching. Exposing the inside of the transceiver to dust or water can cause serious damage to the transceiver. CAUTION: DO NOT place or leave the transceiver in direct sunlight or in places with temperatures below –20°C (–4°F) or above +60°C (+140°F) for IC-M93D, and below –15°C (–10°C for the Australian version) or above +55°C for the IC-M93D EURO. The basic operations of the transceiver are guaranteed within the speciied operating temperature range. However, the Liquid Crystal Display may not operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. CAUTION: DO NOT modify the transceiver. The speciications may change and then the transceiver may not comply with the requirements of required regulations. The transceiver warranty does not cover any problems caused by unauthorized modiication. CAUTION: DO NOT operate the transceiver if it becomes hot after operating it continuously for long periods of time. This may damage the transceiver. KEEP the transceiver and microphone at least 0.9 m (3 feet) away from the vessel’s magnetic navigation compass. RECOMMENDATION DO NOT push [PTT] unless you actually intend to transmit. BE CAREFUL! The IC-M93D and IC-M93D EURO meet IPX7* requirements for waterproof protection. However, once the transceiver has been dropped, waterproof protection cannot be guaranteed because of possible damage to the transceiver’s case or the waterproof seal. CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH WATER after exposure to saltwater, and dry it before operating. Otherwise, the transceiver's keys, switches and controllers may become unusable, due to salt crystallization, and/or the charging terminals of the battery pack may rust. * Only when the speaker microphone jack cover, the optional HM-165, or HM-228 is attached. Even when the transceiver power is OFF, a slight current still lows in the circuits. Remove the battery pack from the transceiver when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced. BE CAREFUL! Even if the volume level is set low, the beeps of the Float ’n Flash, DSC alarm and AquaQuake functions are very loud. BE SURE the transceiver power is OFF before connecting the supplied or optional equipment. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. NOTE: DO NOT wash the transceiver in water if there is any reason to suspect the waterprooing may not be effective. For example, in cases where the [SP MIC] jack cover is damaged, the transceiver/battery pack is cracked or broken, or has been dropped, or when the battery pack is detached from the transceiver. iv INFORMATION FOR CLASS A UNINTENTIONAL RADIATORS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. DISPOSAL The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area. CAUTION: Changes or modiications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. COUNTRY CODE LIST • List of Country codes (ISO 3166-1) 10 11 12 13 14 15 16 17 Country Austria Belgium Bulgaria Croatia Czech Republic Cyprus Denmark Estonia Finland France Germany Greece Hungary Iceland Ireland Italy Latvia Codes AT BE BG HR CZ CY DK EE FI FR DE GR HU IS IE IT LV 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Country Liechtenstein Lithuania Luxembourg Malta Netherlands Norway Poland Portugal Romania Slovakia Slovenia Spain Sweden Switzerland Turkey United Kingdom Codes LI LT LU MT NL NO PL PT RO SK SI ES SE CH TR GB TABLE OF CONTENTS IMPORTANT ...............................................................................................i FEATURES.................................................................................................i EXPLICIT DEFINITIONS ............................................................................i IN CASE OF EMERGENCY ...................................................................... ii PRECAUTIONS........................................................................................ iii RECOMMENDATION ............................................................................... iv INFORMATION..........................................................................................v DISPOSAL.................................................................................................v COUNTRY CODE LIST .............................................................................v 1. OPERATING RULES ...........................................................................1 2. SUPPLIED ACCESSORIES AND ATTACHMENTS........................2–3 ■ Supplied accessories ......................................................................2 ■ Attachments ....................................................................................2 3. PANEL DESCRIPTION....................................................................4–8 ■ Panel description.............................................................................4 ■ Display description ..........................................................................5 ■ Using the software keys ..................................................................7 ■ Software keys..................................................................................7 4. PREPARATIONS ...........................................................................9–10 ■ Entering the MMSI code..................................................................9 ■ Entering the ATIS ID (For Dutch and German versions) ...............10 5. PANEL DESCRIPTION................................................................11–15 ■ Selecting a channel ....................................................................... 11 ■ Adjusting the volume level ............................................................13 ■ Adjusting the squelch level............................................................13 ■ Setting the Call channel ................................................................13 ■ Receiving and transmitting ............................................................14 ■ Lock function .................................................................................14 ■ Monitor function.............................................................................15 ■ AquaQuake Water Draining function .............................................15 ■ Editing a channel name.................................................................15 6. SCAN (Except for the Dutch version) ..........................................16–17 ■ Scan types ...................................................................................16 ■ Setting Favorite channels..............................................................17 ■ Starting a scan ..............................................................................17 7. DUALWATCH/TRI-WATCH (Except for the Dutch version) ...............18 ■ Description ....................................................................................18 ■ Operation ......................................................................................18 8. DSC OPERATION .......................................................................19–44 ■ DSC address ID ............................................................................19 ■ Entering the position and time.......................................................21 ■ Sending DSC calls (Distress) ........................................................22 ■ Sending DSC calls (other).............................................................25 ■ Receiving DSC calls (Distress) .....................................................34 ■ Receiving DSC calls (other) ..........................................................35 ■ DSC Log........................................................................................40 ■ DSC Settings.................................................................................42 9. OTHER FUNCTIONS ..................................................................45–52 ■ MOB (Man OverBoard) .................................................................45 ■ Waypoint .......................................................................................46 ■ Navigation .....................................................................................48 ■ Compass .......................................................................................50 ■ GPS/GNSS ...................................................................................50 ■ Information screen ........................................................................52 10. MENU SCREEN ..........................................................................53–58 ■ Using the Menu screen .................................................................53 ■ Menu screen items ........................................................................54 ■ Radio Settings items .....................................................................55 ■ Coniguration items .......................................................................57 11. BATTERY CHARGING ................................................................59–62 ■ Regular battery charger ................................................................61 ■ Optional battery charger................................................................62 12. OPTIONAL SPEAKER MICROPHONE ............................................63 ■ About the HM-165 .........................................................................63 ■ Attaching the HM-165 ...................................................................63 13. TROUBLESHOOTING ......................................................................64 14. SPECIFICATIONS AND OPTIONS .............................................65–67 ■ Speciications ................................................................................65 ■ Options ..........................................................................................67 15. CHANNEL LIST ...........................................................................68–70 16. SAFETY TRAINING INFORMATION ................................................71 INDEX......................................................................................................72 vi 1 OPERATING RULES D Priorities • Read all rules and regulations pertaining to priorities and keep an up-to-date copy handy. Safety and distress calls take priority over all others. • You must monitor Channel 16 when you are not operating on another channel. • False or fraudulent distress calls are prohibited under law. D Privacy • Information overheard but not intended for you cannot lawfully be used in any way. • Indecent or profane language is prohibited. D Radio licenses (1) SHIP STATION LICENSE You must have a current radio station license before using the transceiver. It is unlawful to operate a ship station which is not licensed. Inquire through your dealer or the appropriate government agency for a Ship-Radiotelephone license application. This government-issued license states the call sign which is your craft’s identiication for radio purposes. (2) OPERATOR’S LICENSE A Restricted Radiotelephone Operator Permit is the license most often held by small vessel radio operators when a radio is not required for safety purposes. The Restricted Radiotelephone Operator Permit must be posted or kept with the operator. Only a licensed radio operator may operate a transceiver. However, non-licensed individuals may talk over a transceiver if a licensed operator starts, supervises, ends the call and makes the necessary log entries. A current copy of the applicable government rules and regulations is only required to be on hand for vessels in which a radio telephone is compulsory. However, even if you are not required to have these on hand it is your responsibility to be thoroughly acquainted with all pertinent rules and regulations. NOTE: Even though the transceiver is capable of operation on VHF marine channels 3, 21, 23, 61, 64, 81, 82 and 83, according to FCC regulations these simplex channels cannot be lawfully used by the general population in USA waters. SUPPLIED ACCESSORIES AND ATTACHMENTS ■ Supplied accessories Handstrap Battery pack Battery charger Power adapter* (with 2 screws) D Battery pack 1. Attach the battery pack to the transceiver. Battery pack Antenna Cigarette lighter cable* 2. Lock the battery pack with the latch. Belt clip *May not be supplied, or different type may be supplied, depending on the transceiver version. ■ Attachments Latch D Flexible antenna Connect the supplied antenna to the antenna connector. CAUTION: • NEVER carry the transceiver by holding the antenna. • Transmitting without an antenna may damage the transceiver. CAUTION: NEVER remove or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver and battery pack, and may result in them being damaged. BE CAREFUL! The latch is tightly locked, so use caution when releasing it. DO NOT use your ingernail. Use the edge of a coin or screwdriver tip to carefully release it. 10 11 12 13 14 15 16 2 SUPPLIED ACCESSORIES AND ATTACHMENTS ■ Attachments (Continued) D Handstrap Pass the handstrap through the loop on the back side of the transceiver to make it easy to carry. D Belt clip Attach or detach the belt clip to/from the transceiver as shown below. To attach the belt clip To detach the belt clip Lift the tab up q and slide the belt clip in the direction of the arrow w. Belt clip BE CAREFUL! Do not break your ingernail. PANEL DESCRIPTION ■ Panel description !1 e UP/DOWN/LEFT/RIGHT KEYS [▲]/[▼]/[◄]/[►] z Push [▲] or [▼] to select the operating channel, Menu items, Menu settings, and so on. z Push [◄] or [►] to slide through the key functions that are assigned to the software keys. (p. 7) z Push to select the desired character or number in the entry mode. (p. 9, 10, 15, 19, 21) !0 Microphone r VOLUME/SQUELCH KEY [VOL/SQL] (p. 13) z Push once to display the volume level setting screen. z Push twice to display the squelch level setting screen. z Hold down for 1 second to turn ON the Monitor function. (p. 15) Display t POWER KEY [ ] Hold down for 1 second to turn the transceiver ON or OFF. y CHANNEL 16 KEY [16/C] z Push to select Channel 16. (p. 11) z Hold down for 1 second to select the Call channel. (p. 11) Speaker u ENTER KEY Push to set the entered data, selected item, and so on. Distress key (p. 25) q PTT SWITCH [PTT] Hold down to transmit, release to receive. i CLEAR/LOCK KEY [CLR/ z Push to cancel the entered data, or to return to the previous screen. z Hold down for 1 second to turn the Key Lock function ON or OFF. (p. 14) 10 11 12 13 14 15 16 w MENU KEY Push to display or close the Menu screen. 3 PANEL DESCRIPTION ■ Panel description (Continued) !1 ■ Display description !5 !0 o SOFTWARE KEYS Slide through the key functions by pushing [◄] or [►], and then push either of the 3 software keys to select the function displayed at the bottom of the display. See “Software keys” on page 7 for details. !0 ANTENNA CONNECTOR (p. 2) Connects the supplied antenna. !1 SPEAKER MICROPHONE JACK (p. 63) Connects the optional external speaker microphone. NOTE: Attach the jack cover when the optional speaker microphone is not used. Otherwise, water will get into the transceiver. !4 !3 !2 !1 !0 q MMSI CODE DISPLAY (p. 9) Displays the entered MMSI code. w STATUS ICON (p. 14) • “TX” is displayed while transmitting. • “MONI” is displayed while the Monitor function is activated. • “BUSY” is displayed while receiving, or when the squelch is open. e POWER INDICATOR (p. 8) • “HI” is displayed when high power is selected. • “LOW” is displayed when low power is selected. PANEL DESCRIPTION r STATUS ICON • “STBY” is displayed while not receiving nor transmitting. • “RT” (Radio Telephone mode) is displayed while receiving or transmitting a signal or when the squelch opens. (p. 13, 56) • “DSC” is displayed while in the DSC mode. t CHANNEL NAME • The channel name is displayed, if entered. (p. 15) • “SCAN” or “SCAN 16” is displayed while scanning. (p. 16) • “DUAL 16” or “TRI 16” is displayed while using the Dualwatch or Tri-watch function. (p. 18) y POSITION/TIME INDICATOR Displays the current position and time when valid GPS data is received, or when manually entered. Received GPS data: • “??” blinks if no GPS data is received for 30 seconds after receiving valid GPS data, and then “??” and a warning message are displayed alternately after 10 minutes. • A warning message is displayed if no GPS data is received for 4 hours after receiving valid GPS data. • “No Position No Time” is displayed if no GPS data is received for 2 minutes after turning ON the transceiver, and then a warning message is displayed. L“Local” is displayed when the UTC Offset time is set. (p. 21) Manually entered GPS data: • A manually entered GPS data is valid for 4 hours, and then a warning message is displayed after 4 hours. L“Manual” is displayed. u SOFTWARE KEY FUNCTION DISPLAY (p. 7, p. 14) • The software key functions are displayed. • “Key Locked” is displayed while the Lock function is ON. i CHANNEL NUMBER READOUT Displays the selected operating channel number. L“A” is displayed when a simplex channel is selected. o CALL CHANNEL ICON (p. 11) Displayed when a Call channel is selected. !0 FAVORITE CHANNEL ICON (p. 17) Displayed when a Favorite channel is selected. !1 MAIL ICON (p. 40) • Displayed when there is an unread message. • Blinks until one of the call messages is read. !2 DSC SWITCH ICON (p. 42) • Displayed when the “CH Auto Switch” is set to “Ignore” or “Manual” • Blinks when the “DSC Switch” is OFF. !3 BATTERY INDICATOR Displays the battery’s remaining power. Indication Battery level Full Mid Charging required Battery exhausted blinks when the battery is overcharged (or over voltage) !4 GPS ICON • Stays ON while valid GPS position data is received. • Blinks while no position data is received. !5 CHANNEL GROUP ICON • The selected Channel Group’s icon is displayed. • “WX” is displayed for the Weather channel in the USA, Australian, and Export versions. (p. 12) 10 11 12 13 14 15 16 3 PANEL DESCRIPTION ■ Using the software keys ■ Software keys Various often-used functions are assigned to the software keys for easy access. The functions’ icons are displayed above the software keys, as shown below. You can assign the following functions to the software keys on the Menu screen. D Selecting a software key function 1. Push [◄] or [►] to slide through the selectable functions that are assigned to the software keys. 2. Push the software key under the function’s icon to select the function. (Example: Selecting a Favorite channel) Distress Call (p. 22) Push to display the “Distress Call” screen to select the nature of the call, and then to make a call. NEVER MAKE A DISTRESS CALL IF YOUR SHIP OR A PERSON IS NOT IN AN EMERGENCY. A DISTRESS CALL SHOULD BE MADE ONLY WHEN IMMEDIATE HELP IS NEEDED. Other DSC (p. 25) Push to compose an Individual Call, Group Call, All Ships Call, or a Test Call. LOG Push [◄] Push [►] (p. 40) Push to display the received call log or distress message log. Scan (p. 16) Push to start or stop a Normal or Priority scan. NOTE: The displayed icons, or their order, may differ, depending on the transceiver version or the presetting. Ask your dealer for presetting details. Dualwatch/Tri-watch Push to start or stop Dualwatch or Tri-watch. (p. 18) PANEL DESCRIPTION High/Low (p. 5) Push to set the power to high or low. (p. 11~12) Push to select regular channels or Weather* channels. is displayed except for the USA, Australian, and Export versions. LWhile the Call channel or Channel 16 is displayed, push this key to return to the regular channel mode. *The Weather channels are for only the USA, Australian, and Export versions. AquaQuake (p. 15) Hold down to turn ON the AquaQuake function to clear water from the speaker grill. Favorite channel (p. 17) z Push to select a Favorite channel. z Hold down for 1 second to set the displayed channel as a Favorite channel. z While a Favorite channel is displayed, hold down for 1 second to clear the Favorite channel setting. Channel Name (p. 57) Push to display the backlight brightness adjustment screen. LSome channels are set to only low power. Channel/Weather channel Backlight (p. 15) Push to edit the name of the displayed channel. LWhile in the adjustment mode, push [▲]/[▼][◄]/[►] to adjust the brightness to between 1 and 7, or OFF. MOB (p. 45) z Push to display the “MOB” screen. z Hold down for 1 second to memorize the current position as the Man OverBoard (MOB) waypoint. Waypoint (p. 46) z Push to display the “Waypoint” screen. z Hold down for 1 second to memorize the current position as a Waypoint. Navigation (p. 48) While displaying the “MOB” or “Waypoint” screen, push this key to start navigating to the selected position. Compass (p. 50) 10 11 12 13 14 15 16 Push to display the “Compass” screen to check the vessel’s course heading, Speed Over Ground (SOG) and Course Over Ground (COG). 4 PREPARATIONS ■ Entering the MMSI code The Maritime Mobile Service Identity (MMSI: DSC self ID) code consists of 9 digits. You can only enter the code when turning ON the transceiver for the irst time. 4. 5. This initial code entry can be done only once. After entering, it can be changed only by your dealer or distributor. If your MMSI code has already been entered, this entry is not necessary. 6. 1. Hold down [ ] to turn ON the transceiver. • Three short beeps sound, and “Push [ENT] to Register your MMSI” is displayed. 2. Push [ENT] to start entering the MMSI code. • The “MMSI Input” screen is displayed. LPush [CLR] twice to skip the entry. If you skip the entry, you cannot make a DSC call. To enter the code after skipping, turn OFF the power, and then turn it ON again. 3. Repeat step 3 to enter all 9 digits. Push the software key below [DONE] to set the entered code. • The “Conirmation” screen is displayed. 7. Enter your MMSI code again to confirm. Push the software key below [DONE] to set the entered code. LWhen your MMSI code is successfully entered, “MMSI Successfully Registered” is briely displayed, and then the operating screen opens. LYour MMSI code is also displayed on the operating screen. Enter the MMSI code. TIP: • Select a number using [◄] and [►]. • Push [ENT] to enter the selected number. • Select “←” or “→,” to move the cursor. NOTE: For the Dutch and German versions, entering the ATIS ID is also required. See the next page for details. PREPARATIONS ■ Entering the ATIS ID (For Dutch and German versions) The Automatic Transmitter Identification System (ATIS) ID consists of 10 digits. You can enter the ID in the “ATIS ID Input” item on the Menu screen. This ID entering can be done only once. After entering, it can be changed only by your dealer or distributor. If your ATIS ID has already been entered, this entry is not necessary. 1. Push [MENU]. • The Menu screen is displayed. 2. Push [▲] or [▼] to select “ATIS ID Input,” and then push [ENT] to start entering. • The “ATIS ID Input” screen is displayed. 3. Enter your ATIS ID. TIP: • Select a number using [◄] and [►]. • Push [ENT] to enter the selected number. • Select “←” or “→,” to move the cursor. 4. 5. Repeat step 3 to enter all 10 digits. Push the software key below [DONE] to set the entered ID. • The “Conirmation” screen is displayed. 6. 7. Enter your ATIS ID again to confirm. Push the software key below [DONE] to set the entered ID. LWhen your ATIS ID is successfully entered, the screen displays “ATIS ID Successfully Registered,” and then the operating screen opens. LYou can check the ATIS ID in “Information” on the Menu screen. 10 11 12 13 14 15 16 10 5 BASIC OPERATIONS ■ Selecting a channel NOTE: Before using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. To avoid damage to the transceiver, turn OFF the transceiver before charging. D Channel 16 Channel 16 is the distress and safety channel. It is used to establish the initial contact with a station and for emergency communications. Channel 16 is monitored during both Dualwatch and Tri-watch. While in the standby mode, you must monitor Channel 16. Push [16/C] to select Channel 16. LTo return to the previously selected channel, push the software key below [CHAN] or [CH/WX]. 11 D Call channel Each Channel Group has separate leisure-use Call channels. The Call channel is monitored during Tri-watch. The Call channels can be selected and used to store your most often used channel in each Channel Group, for quick recall. LSee page 13 for details on setting the Call channel. Hold down [16/C] for 1 second to select the Call channel. • The Call channel number and “CALL” are displayed. LTo return to the previously selected channel, push the software key below [CHAN] or [CH/WX]. BASIC OPERATIONS D Selecting a Channel Group Channel Groups are preset into your transceiver. You can select the Channel Group between USA, International, Canadian, DSC, and ATIS depending on the transceiver version. Version USA UK European Dutch German Australian Export (Other) 1. USA Preset Channel Group INT CAN DSC Push [MENU]. ATIS D Weather channels and Weather Alert For the USA, Australian, and Export versions, the transceiver has 10 preset Weather channels. You can use these channels to monitor broadcasts from the National Oceanographic and Atmospheric Administration (NOAA). The transceiver automatically detects a Weather alert tone on the selected weather channel, or while scanning. Selecting a Weather channel 1. Push the software key below [CH/WX] on the software key. • “WX” is displayed on the operating screen instead of the Channel Group icon. 2. • The Menu screen is displayed. 2. Push [▲] or [▼] to select “Radio Settings,” and then push [ENT]. • The “Radio Settings” screen is displayed. 3. Push [▲] or [▼] to select “CHAN Group,” and then push [ENT]. Push [▲] or [▼] to select the Channel Group, and then push [ENT]. LSelect [EXIT] to exit the Menu screen. LThe selected Channel Group’s icon is displayed on the operating screen. Push [▲] or [▼] to select a Weather channel. Setting the Weather Alert LSee page 55 for details on the Weather Alert function. 1. 2. • The “CHAN Group” screen is displayed. 4. Push [MENU]. Push [▲] or [▼] to select “Radio Settings,” and then push [ENT]. • The “Radio Settings” screen is displayed. 3. Select “WX Alert,” and then push [ENT]. 4. Select “On with Scan” or “On.” 10 11 12 13 14 15 16 • The “WX Alert” screen is displayed. • “ ” is displayed next to the weather channel icon. 12 5 BASIC OPERATION ■ Adjusting the volume level ■ Setting the Call channel 1. By default, a Call channel is set in each Channel Group. You can set your most often-used channel as your Call channel in each Channel Group for a quick recall. Push [VOL/SQL]. • The volume level adjustment screen is displayed. 2. Push [◄] or [►] to adjust the volume level between 1 and 20, or OFF. LYou can also push the software key below [MUTE] to select OFF, or below [LOUD] to set the maximum volume level. LIf no key is pushed for 5 seconds, the screen automatically closes. 3. Push [ENT] to set. 1. Push [MENU]. • The Menu screen is displayed. 2. Push [▲] or [▼] to select “Radio Settings,” and then push [ENT]. • The “Radio Settings” screen is displayed. 3. Push [▲] or [▼] to select “Call Channel,” and then push [ENT]. • The “Call Channel” screen and the default Call channel is displayed. ■ Adjusting the squelch level Squelch enables the audio to be heard only while receiving a signal that is stronger than the set level. A higher level blocks weak signals, which enables you to receive only stronger signals. A lower level enables you to hear weak signals. 1. Push [VOL/SQL] twice. • The squelch level adjustment screen is displayed. 2. Push [◄] or [►] to adjust the volume level between 1 and 10, or Open. LIf no key is pushed for 5 seconds, the adjustment screen automatically closes. 3. 13 Push [ENT] to set. 4. 5. Push [▲] or [▼] to select the channel. Push [ENT] to set the selected channel as the Call channel. LPush the software key below [EXIT] to return to the operating screen. BASIC OPERATION ■ Receiving and transmitting CAUTION: Transmitting without an antenna may damage the transceiver. 1. NOTE: • To conserve battery power, the Power Save function automatically turns ON when no signal is received for 5 seconds. • When the temperature is extremely high, the battery protection function automatically sets transceiver power to Low, and disables High power selection. • Except for the Export version, the Time-out Timer function cuts OFF transmission after 5 minutes of continuously transmitting, to prevent prolonged transmission. • The Noise Cancel function reduces random noise components in the transmit and/or received signal. See page 56 for details. Push [▲] or [▼] to select the channel to call. LYou cannot transmit on Channel 70. is displayed while receiving a signal. 2. Hold down [PTT] and speak into the microphone. • 3. is displayed while transmitting. Release [PTT] to receive. Speak into the microphone Hold down to transmit. Release to receive. Select a channel. TIP: To maximize the readability of your transmitted signal, pause for a second after pushing [PTT] and hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, and then speak at your normal voice level. ■ Lock function The Lock function electronically locks all keys except for [ ], [PTT], and [DISTRESS]. This function enables you to prevent accidentally changing the channel, or accessing the functions. 10 11 12 13 14 15 16 Hold down [CLR é] for 1 second to turn the Lock function ON or OFF. • is displayed on the bottom of the display while the Lock function is ON. 14 5 BASIC OPERATION ■ Monitor function ■ Editing a channel name The Monitor function temporarily cancels the Squelch function to check for weak signals. You can edit the name of each operating channel and weather channel, using numbers, uppercase letters, symbols, and a space. This enables easy recognition of the channels or stations. All VHF marine channels are set with default names. 1. Hold down [VOL/SQL] to turn ON the Monitor function. LThe Monitor function is ON while [VOL/SQL] is held down. • is displayed. • If there is a weak signal, you can hear the signal and noise. 2. Release to turn OFF. TIP: You can change the Monitor function settings. See page 55 for details. ■ AquaQuake Water Draining function 1. 2. LYou cannot edit a channel name during Dualwatch, Tri-watch, or a Scan. 3. Push [◄] or [►] to select Hold down the software key below function. to turn ON the • A low frequency vibration beep sounds to drain the water, regardless of the volume level setting. LThis function is activated for a maximum of 10 seconds, even if you continue to hold down the software key. 3. Release the key to turn OFF the function. NOTE: You cannot use this function when an external speaker microphone is connected. 15 Push the software key below • The “Channel Name” screen is displayed. 4. Edit the channel name. TIP: • Select [! $ ?] to enter characters, and select [ABC] to enter numbers and letters. • Select characters or space using [▲]/[▼]/[◄]/[►]. • Push [ENT] to enter the selected character. • Select “←” or “→,” to move the cursor. • Push the software key below to cancel editing. Water in the speaker grill may mufle the sound coming from the speaker. The AquaQuake Water Draining function removes water from the speaker grill by vibrating the speaker. 1. 2. Push [▲] or [▼] to select the channel to edit. Push [◄] or [►] to select 5. Push the software key below [DONE] to set the edited name. SCAN (Exept for the Dutch version) ■ Scan types You can ind ongoing calls by scanning the Favorite channels. Before starting a scan, you need to: • Set the channels that you want to scan as Favorite channels. (p. 17) Priority Scan The Priority Scan sequentially searches through all Favorite channels, while also monitoring Channel 16. LOnly the Favorite channels are scanned. CH 01 • Set the scan type to “Priority Scan” or “Normal Scan” on the “Radio Settings” screen. (p. 55) Normal Scan The Normal Scan sequentially searches through all Favorite channels. However, Channel 16 is not checked unless it is set as a Favorite channel. WX* CH 16 CH 05 CH 01 CH 03 CH 04 CH 02 WX* CH 03 CH 05 CH 02 CH 04 *For USA, Australian, and Export versions. When the Weather Alert function is ON, the previously selected Weather channel is also scanned. *For USA, Australian, and Export versions. When the Weather Alert function is ON, the previously selected Weather channel is also scanned. When a signal is received: On Channel 16 The scan pauses until the signal disappears. On a channel other than Channel 16 The scan becomes Dualwatch until the signal disappears. 10 11 12 13 14 15 16 16 6 SCAN (Except for the Dutch version) ■ Setting Favorite channels ■ Starting a scan You can quickly recall often-used channels by setting them as Favorite channels. You can set Favorite channels in each Channel Group. 1. 2. 3. Select a Channel Group. (p. 12) Push [◄] or [►] to display Push the software key below 4. To stop the scan, push the software key below 1. 2. 3. 4. Select a Channel Group. (p. 12) Push [▲] or [▼] to select the channel you want to set as a Favorite channel. Push [◄] or [►] to display Hold down the software key below for 1 second. • The selected channel is set as a Favorite channel, and “ ” is displayed. LTo cancel the setting, hold down the key again for 1 second. TIP: You can set all channels as Favorite channels, clear all settings, or reset to the default. By default, some channels are preset as Favorite channels. The preset channels differ, depending on the transceiver version. • The scan starts. •“ ” is displayed during a Priority Scan, and “ ” is displayed during a Normal Scan. LWhen a signal is received, the scan pauses until the signal disappears, or resumes after 5 seconds, depending on the Scan Timer setting in “Radio Settings.” LA beep sounds and “16” blinks when a signal is received on Channel 16 during a Priority scan. TIP: In order to properly receive signals, be sure to adjust the squelch to a suitable level. Example: Starting a Normal Scan Push to start 17 “ While scanning ” is displayed. “ When a signal is received ” and “ ” are displayed. DUALWATCH/TRI-WATCH (Except for the Dutch version) ■ Description ■ Operation Dualwatch and Tri-watch are convenient to monitor Channel 16 while you are operating on another channel. 1. Normal channel 4. Ch 88 Ch 16 Ch 88 2. 3. Normal channel Call Ch 9 channel Ch 16 Monitors Channel 16 while receiving on another channel. Monitors Channel 16 and the Call channel while receiving on another channel. Dualwatch Tri-watch 5. Select Dualwatch or Tri-watch in “Radio Settings.” (p. 55) Push [▲] or [▼] to select a channel. Push [◄] or [►] to display (Dualwatch) or (Tri-watch). Push the software key below the or • Dualwatch or Tri-watch starts. •“ ” is displayed for Dualwatch, and “ is displayed for Tri-watch. LBeeps sound when a signal is received on Channel 16. ” To cancel Dualwatch or Tri-watch, push the software key again. Example: Operating Tri-watch on INT Channel 25. When a signal is received: On Channel 16 Dualwatch/Tri-watch pauses on Channel 16 until the signal disappears. On the Call channel Tri-watch switches to Dualwatch until the signal on the Call channel disappears. Push to start Signal is received on the Call channel. “ ” is displayed. 10 11 12 13 14 15 16 Signal received on Channel 16 takes priority. “16” blinks. LTri-watch resumes after the signal disappears. 18 8 DSC OPERATION ■ DSC address ID D Entering an Individual ID You can enter a total of 75 Individual IDs, and assign names of up to 10 characters. 1. 4. TIP: Display the “Individual ID” screen. • Select [! $ ?] to use characters, and select [ABC] to use numbers and letters. • Select characters or space using [▲]/[▼]/[◄]/[►]. • Push [ENT] to enter the selected character. • Select “←” or “→,” to move the cursor. [MENU] ► “DSC Settings” ► “Individual ID” • “No ID” is displayed if no ID is entered. 2. Push the software key below [NEXT] to start entering the name. Push the software key below [ADD]. • The Individual ID’s entry screen is displayed. 3. Enter the Individual ID. TIP: • Select a number using [◄] and [►]. • Push [ENT] to enter the selected number. • Select “←” or “→,” to move the cursor. NOTE: the irst digit is ixed as “0” for a Group ID. The irst two digits are ixed as “0” for any Coast station ID. 19 5. After entering, push the software key below [DONE] to save, and return to the previous screen. • The entered name is displayed. DSC OPERATION D Entering a Group ID You can enter a total of 25 Group IDs, and assign names of up to 10 characters. 1. D Deleting an Individual ID or Group ID [Example: Deleting an Individual ID: ICOM #2] 1. Display the “Individual ID” screen. [MENU] ► “DSC Settings” ► “Individual ID” Display the “Group ID” screen. [MENU] ► “DSC Settings” ► “Group ID” 2. 3. Push [▲] or [▼] to select “ICOM #2.” Push [►] to display [DEL]. 4. Push the software key below [DEL]. • “No ID” is displayed if no ID is entered. 2. Push the software key below [ADD]. • The Group ID’s entry screen is displayed. 3. Enter the Group ID and its name in the same way as described on the previous page. NOTE: The irst digit is ixed as “0” for a Group ID. The irst two digits are ixed as “0” for any Coast station ID. 4. After entering, push the software key below [DONE] to save, and return to the previous screen. • The entered name is displayed. • “Are you sure?” is displayed. 5. Push the software key below [OK] to delete. LPush the software key below [CANCEL] to cancel the deletion. • The selected ID is deleted, and then returns to the previous screen. 10 11 12 13 14 15 16 TIP: You can edit an ID and its name by pushing the software key below [EDIT] in step 3. 20 8 DSC OPERATION ■ Entering the position and time A Distress call should include the vessel’s position and time. If no GPS data is received, manually enter the position and Universal Time Coordinated (UTC) time. NOTE: • The manual entry is disabled while the GPS data is received. • The manually entered position and time is valid only for 4 hours, or until turning OFF the transceiver. 1. Display the “Position Input” screen. [MENU] ► “DSC Settings” ► “Position Input” 2. Enter the latitude and longitude. TIP: • Select a number or a compass direction using [▲]/[▼]/[◄]/[►]. • Push [ENT] to enter the selected number. • Select “←” or “→,” to move the cursor. • Push the software key below [NEXT] to change the entry between latitude, longitude, and UTC. 21 3. Push the software key below [NEXT] to start entering the UTC time. LUse the TIP in step 2 to enter. 4. Push the software key below [DONE] to set the entered position and time. • Returns to the previous screen. LThe entered position and time are displayed on the operating screen. L“Manual” is displayed next to the time display. DSC OPERATION ■ Sending DSC calls (Distress) A Distress call should be sent if, in the opinion of the Master, the ship or a person is in distress and requires immediate assistance. 4. Push any software key to turn OFF the alarm. • Channel 16 is automatically selected. NEVER MAKE A DISTRESS CALL IF YOUR SHIP OR A PERSON IS NOT IN AN EMERGENCY. A DISTRESS CALL SHOULD BE MADE ONLY WHEN IMMEDIATE HELP IS NEEDED. D Simple call 1. 2. Confirm that no Distress call is being received. While lifting up the key cover, hold down [DISTRESS] for 3 seconds until you hear 3 short countdown beeps and a long beep sound. • The backlight blinks. 3. After sending, wait for an Acknowledgement call. • “Waiting for ACK” is displayed. LThe Distress call is automatically sent every 3.5 to 4.5 minutes, until an Acknowledgement is received, or a Distress Cancel call is sent. (p. 24) LWhen you receive an Acknowledgement, alarm sounds. 5. 6. Hold down [PTT] to explain your situation. Push the software key below [EXIT] to return to the operating screen. TIP: A default Distress alert contains: • Nature of distress: Undesignated distress • Position information: The latest GPS, or manually input position, which is held for 4 hours or until turning OFF the transceiver. NOTE on Distress calls (Simple calls and Regular calls): If no valid position data is received when sending a Distress call, the transceiver waits for 15 seconds until position data is received, and then the Distress call is sent. If no position is received during this 15 seconds, the position data in the transceiver memory is automatically sent. However, if there is no position data in the memory, the Distress call is sent without position data. 10 11 12 13 14 15 16 22 8 DSC OPERATION D Regular call Select the nature of the Distress call to include in the Regular Distress call. 1. Push the software key below 4. After sending, wait for an Acknowledgement call. • “Waiting for ACK” is displayed. • The “Distress Call” screen is displayed. 2. Push [▲] or [▼] to select the nature of the call, and then push [ENT]. (Example: Flooding) • The conirmation screen is displayed. LIf no valid GPS data is being received, the latitude, longitude, and UTC entry mode is displayed. LSee “Entering the position and time” on page 22 for details.” 3. While lifting up the key cover, hold down [DISTRESS] for 3 seconds until you hear 3 short countdown beeps and a long beep sound. LThe Distress call is automatically sent every 3.5 to 4.5 minutes, until an Acknowledgement is received, or a Distress Cancel call is sent. (p. 24) LWhen an Acknowledgement is received, an alarm sounds. 5. Push any software key to turn OFF the alarm. • Channel 16 is automatically selected. • The backlight blinks. TIP: You can also send a Regular call by selecting the “Compose Distress” item on the Menu screen. 6. 23 Hold down [PTT] to communicate. DSC OPERATION D Distress Cancel call NOTE (For USA and Export versions): After sending a Distress call without position data • While waiting for an Acknowledgement, if valid position data is received, the transceiver will automatically send a Distress call again. • Even after exiting the DSC mode, if valid position data is received within 20 minutes after receiving a Distress Acknowledgement, the transceiver will automatically send a Distress call again. If you have accidently made a Distress call, or made an incorrect Distress call, send a Distress Cancel call to cancel the call as soon as possible while waiting for an Acknowledgement call, and report the purpose of the cancellation. 1. • The screen below is displayed. 2. After receiving an Acknowledgement: [EXIT]: Closes the Distress operation, and returns to the operating screen. [HIST]: Displays the “Distress History.” [INFO]: Displays the information of the received Distress Acknowledgement. Push the software key below [CONT]. • The Distress Cancel call is sent. • Channel 16 is automatically selected. D Distress call software key description While waiting for an Acknowledgement: [CANCEL]: Cancels the Distress call and enables you to send a Cancel call. (See the right column) [RESEND]: Enables you to resend the Distress call by holding down [DISTRESS] again. [PAUSE]: Pauses the countdown to resend the next Distress call. [INFO]: Displays the information of the Distress call that you have sent. While waiting for an Acknowledgement call, push the software key below [CANCEL]. 3. Hold down [PTT] to report the purpose of the cancellation. 4. After communicating, push the software key below [FINISH]. LYou can display the wording of the cancellation by pushing [▼]. 10 11 12 13 14 15 16 • The screen to the right is displayed. 5. Push the software key below [OK] to finish the Distress Cancel call. • Returns to the operating screen. 24 8 DSC OPERATION ■ Sending DSC calls (other) NOTE: To ensure proper DSC operation, be sure to correctly adjust the “CH 70 SQL Level” item on the Menu screen. (p. 44) 6. • “Transmitting Individual Call” is displayed, and then “Waiting for ACK” is displayed. LIf Channel 70 is busy, the transceiver stands by until the channel becomes clear. D Sending an Individual call An Individual call enables you to send a DSC signal to only a speciic station. You can communicate after receiving the Acknowledgement “Able to comply.” 1. 2. Push [◄] or [►] to display Push the software key below Push the software key below [CALL] to send the Individual call. • The “Compose Other” screen is displayed. LYou can also display the “Compose Other” screen by selecting the “Compose Other” item on the Menu screen. 3. Push [▲] or [▼] to select “Individual Call,” and then push [ENT]. • The “Individual Call” screen is displayed. 4. Select the station to send an Individual call to, and the push [ENT]. 7. • An alarm sounds. • The screen to the right is displayed. 8. LYou can also select “Manual Input” to manually enter the calling station. 5. 25 Push any software key to turn OFF the alarm. • The channel assigned in step 5 is automatically selected. LIf the called station cannot use the channel that you assigned, a different channel is selected by the station. Select a channel to assign, and then push [ENT]. LThe assigned channels are preset by default. When you receive an Acknowledgement “Able to comply”: 9. Hold down [PTT] to communicate. DSC OPERATION Acknowledgement “Unable to comply” Push any software key to turn OFF the alarm. • The Acknowledge information is displayed. LPush the software key below [EXIT] to return to the operating screen. D Sending an Individual Acknowledgement When you have received an Individual call (p. 35), send an Acknowledgement to the calling station. When you send an Acknowledgement, select “Able to Comply,” “Propose New CH,” or “Unable to Comply.” 1. 2. While an Individual call is being received, push any software key to turn OFF the alarm. Push the software key below [ACPT]. • The received call’s information is displayed. LIf you want to send an Acknowledgement “Able to comply right away, push the software key below [ABLE]. LIf you cannot communicate, and want to return to the operating screen, push the software key below [IGN]. 3. Push the software key below [ACK]. • The Acknowledgement category screen is displayed. Continued on the next page. 10 11 12 13 14 15 16 26 8 DSC OPERATION D Sending an Individual Acknowledgement (Continued) 4. Select “Able to Comply,” “Unable to Comply,” or “Propose New CH.” Sends an Acknowledgement call without any changes. • Unable to Comply: Sends an Acknowledgement call but cannot communicate. • Propose New CH: Able to communicate but proposes another channel. Specify the channel by pushing [▲] or [▼]. (Example: Channel 77) • Able to Comply: 5. Push the software key below [CALL] to send the Acknowledgement call. Sending on the “Compose Other” screen You can also send an Individual Acknowledgement by selecting “Individual ACK” on the “Compose Other” screen. This enables you to resend an Acknowledgement, or send even after sending an “Unable to Comply” Acknowledgement. 1. Push the software key below • The ”Compose Other” screen is displayed. 2. Push [▲] or [▼] to select “Individual ACK,” and then push [ENT]. • The Individual caller’s station or MMSI is displayed. L“Individual ACK” is not displayed if no Individual call has been received. 3. Select the station to send an Acknowledgement call to, and the push [ENT]. 4. Repeat steps 3 to 5 described on the left column. • “Transmitting Individual ACK” is displayed, and then the assigned channel is automatically selected. 6. 27 Push [PTT] to communicate. DSC OPERATION D Sending a Group call A Group call enables you to send a DSC signal to only a speciic group. 6. LYou can send a Group call to a pre-entered group address, or manually enter the address before sending. (p. 20) 1. 2. Push [◄] or [►] to display Push the software key below Push the software key below [CALL] to send the Group call. • “Transmitting Group Call” is displayed, and then the assigned channel is automatically selected. LIf Channel 70 is busy, the transceiver stands by until the channel becomes clear. • The “Compose Other” screen is displayed. LYou can also display the “Compose Other” screen by selecting the “Compose Other” item on the Menu screen. 3. Push [▲] or [▼] to select “Group Call,” and then push [ENT]. • The “Group Call” screen is displayed. 4. Select the group to send a Group call to, and the push [ENT]. LYou can also select “Manual Input” to manually enter the target group. 5. Select the channel to assign, and then push [ENT]. LThe assigned channels are preset by default. 7. Hold down [PTT] to communicate. 10 11 12 13 14 15 16 28 8 DSC OPERATION D Sending an All Ships call Except for the USA and Export versions, you can send a call to all ships that carry DSC transceivers and to those that use Channel 70 as their listening channel in the range. 1. 2. Push [◄] or [►] to display Push the software key below 6. Push the software key below [CALL] to send the All Ships call. • “Transmitting All Ships Call” is displayed, and then the assigned channel is automatically selected. LIf Channel 70 is busy, the transceiver stands by until the channel becomes clear. • The “Compose Other” screen is displayed. LYou can also display the “Compose Other” screen by selecting the “Compose Other” item on the Menu screen. 3. Push [▲] or [▼] to select “All Ships Call,” and then push [ENT]. • The “All Ships Call” screen is displayed. 4. Select the category “Safety” or “Urgency.” 7. 5. Select the traffic channel to assign, and then push [ENT]. LThe assigned channels are preset by default. 29 Hold down [PTT] to communicate. DSC OPERATION D Sending a Test call You should avoid testing calls on the exclusive DSC distress channels and safety calling channels. When you cannot avoid testing on a distress or safety channel, you should indicate that these are test calls. Normally the test call would require no further communications between the two stations involved. 1. 2. Push [◄] or [►] to display Push the software key below 5. Push the software key below [CALL] to send the Test call. • “Transmitting Test Call” is displayed. LIf Channel 70 is busy, the transceiver stands by until the channel becomes clear. • The “Compose Other” screen is displayed. LYou can also display the “Compose Other” screen by selecting the “Compose Other” item on the Menu screen. 3. Push [▲] or [▼] to select “Test Call,” and then push [ENT]. • The “Test Call” screen is displayed. 4. Select the station to send the Test call to. LYou can also select “Manual Input” to manually enter the calling station. 6. When you receive an Acknowledgement: 7. Push any software key to turn OFF the alarm. • Alarm sounds. • The screen to the right is displayed. • The Acknowledgement information is displayed. 8. Push the software key below [EXIT]. • “Terminate the Procedure Are you sure?” is displayed. 9. 10 11 12 13 14 15 16 Push the software key below [OK] to return to the operating screen. 30 8 DSC OPERATION D Sending a Test Acknowledgement By default, when you receive a Test call, the Auto ACK function automatically sends an Acknowledgement to the calling station (p. 42). If the function is set to “Manual,” do the following steps to send an Acknowledgement. 1. 2. 4. Push the software key below [CALL] to send the Acknowledgement. • “Transmitting Test ACK” is displayed. After a Test call is being received, push any software key to turn OFF the alarm. Push the software key below [ACPT]. • The received call’s information is displayed. LIf you want to send an “Able to comply” Acknowledgement right away, push the software key below [ABLE]. 5. 6. 3. Push the software key below [ACK]. • The “Test ACK” conirmation screen is displayed. 31 Push the software key below [EXIT]. • A confirmation screen is displayed. Push the software key below [OK] to return to the operating screen. DSC OPERATION D Sending a Position Reply call Sending on the “Compose Other” screen You can also send a Test Acknowledgement by selecting “Test ACK” on the “Compose Other” screen. This enables you to resend an Acknowledgement, or send even after ignoring the call when you irst received it. 1. Push the software key below 1. • The ”Compose Other” screen is displayed. 2. Send a Position Reply call when a Position Request call is received. If the Auto ACK function is set to “Auto,” the Acknowledgement is automatically sent to the calling station. (p. 42) 2. Push [▲] or [▼] to select “Test ACK,” and then push [ENT]. While a Position Request call is being received, push any software key to turn OFF the alarm. Push the software key below [ACPT]. • The received call’s information is displayed. LIf you want to send an “Able to Comply” Acknowledgement right away, push the software key below [ABLE]. LIf you cannot send a reply call, push the software key below [UNABL]. • The Test caller’s station or MMSI is displayed. L“Test ACK” is not displayed if no Test call has been received. 3. Push the software key below [ACK]. 10 11 12 13 14 15 16 Continued on the next page. 32 8 DSC OPERATION D Sending a Position Reply call (Continued) 4. Select the reply “Able to Comply.” LSelect “Unable to Comply” if you cannot send a reply call. 5. Push the software key below [CALL] to send the reply. • “Transmitting Position Reply” is displayed. • After sending, the replied information is displayed. Sending on the “Compose Other” screen You can also send a Position Reply call by selecting “Position Reply” on the “Compose Other” screen. This enables you to reply even after ignoring the call when you irst received it. 1. Push the software key below • The ”Compose Other” screen is displayed. 2. Push [▲] or [▼] to select “Position Reply,” and then push [ENT]. • The caller’s station or MMSI is displayed. L“Position Reply” is not displayed if no Position Request call has been received. 6. 3. Select the station to send a Position Reply call to, and the push [ENT]. 4. Repeat steps 4 to 7 described in the left column. Push the software key below [EXIT] to return to the operating screen, or below [RESEND] to resend. • A confirmation screen is displayed. 7. Push the software key below [OK] to return to the operating screen. TIP: If no valid position is received while selecting [ACPT] in step 2, and selecting “Able to Comply,” the position and time entry screen is displayed. LSee “Entering the position and time” on page 22 for details. 33 DSC OPERATION ■ Receiving DSC calls (Distress) The transceiver receives Distress calls, Distress Acknowledgement calls, and Distress Cancel calls. LWhen you receive a call, an emergency alarm sounds. NOTE: The screens that are displayed when a Distress call or an Acknowledgement call is received slightly differ from one another. The following steps are described using an example of receiving a Distress call. When a Distress call is received: • The emergency alarm sounds until you turn it OFF. • “RCVD Distress” is displayed. 1. 2. Push any software key to turn OFF the alarm. Push the software key below the intended operation. [PAUSE] L[PAUSE] is not displayed if the “CH Auto Switch” item is set to “Manual.” (p. 42) • Pauses the countdown until the assigned channel is automatically selected. • Select [RESUME] to resume the countdown. • The call is saved in the DSC Log. [ACPT] • Accepts the call. • Channel 16 is automatically selected. • Monitor Channel 16 as a coast station may require assistance. • After Channel 16 is selected, you can select your next operation by pushing the software key below the following options. [EXIT]: Returns to the operating screen. [HIST]: Displays the “Distress History” screen. [POS]: Displays the position of the calling station on a map*. LThe map is not updated,even as your vessel moves. [INFO]: Displays the information of the received Distress call. [IGN] • Returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. 10 11 12 13 14 15 16 *Note on the map: See “Navigation screen description” on page 49 for details on “RNG,” “N-UP,” “BRG,” and “DIST.ˮ 34 8 DSC OPERATION ■ Receiving DSC calls (other) The transceiver receives the following types of DSC calls. • Individual call (p. 35) • Individual Acknowledgement call (p. 25) • Group call (p. 36) • All Ships call (p. 37) • Position Request call (p. 38) • Test call (p. 39) • Test Acknowledgement call (p. 40) D Receiving an Individual call When an Individual call is received: • The alarm sounds. • “RCVD INDV Call” is displayed. 1. Push any software key to turn OFF the alarm. 2. Push the software key below the next operation. [IGN] • Ignores the call and returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. 35 [ABLE] • Sends an Individual Acknowledgement call right away. • The assigned channel is automatically selected. • After sending, [RESEND] to resend. • The call is saved in the DSC Log. [ACPT] • Accepts the call. • The assigned channel is automatically selected. • The call is saved in the DSC Log. • The received call’s information is displayed. • Push the software key below [ACK] to select the Acknowledgement option. Able to Comply: Sends an Acknowledgement call without any changes. Unable to Comply: Sends an Acknowledgement but you cannot communicate. Propose New CH: Sends an Acknowledgement call but on another channel. Assign the channel by pushing [▲] or [▼]. NOTE: If the Auto ACK function is set to “Auto (Unable)” the Acknowledgement “Unable to Comply” is automatically sent to the calling station when the call is received. (p. 42) LFor the USA and Export versions, this function is set to “Auto (Unable)” by default. DSC OPERATION D Receiving a Group call When a Group call is received: • The alarm sounds for 2 minutes. • “RCVD Group Call” is displayed. 1. Push any software key to turn OFF the alarm. LThe channel that is assigned by the caller is automatically selected after 10 seconds by default. 2. Push the software key below your next operation. [PAUSE] L[PAUSE] is not displayed if the “CH Auto Switch” item is set to “Manual.” (p. 42) • Pauses the countdown until the assigned channel is automatically selected. • Select [RESUME] to resume the countdown. • The call is saved in the DSC Log. [ACPT] • Accepts the call. • The assigned channel is selected. • The call is saved in the DSC Log. [EXIT] Closes the Group call, and then returns to the operating screen. [INFO] The received call’s information is displayed. [IGN] • Ignores the call and returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. 10 11 12 13 14 15 16 36 8 DSC OPERATION D Receiving an All Ships call When an All Ships call is received: • The alarm sounds. • “RCVD All Ships Call” is displayed. 1. Push any software key to turn OFF the alarm. LThe trafic channel that is assigned by the caller is automatically selected after 10 seconds by default. 2. Push the software key below your next operation. [PAUSE] L[PAUSE] is not displayed if the “CH Auto Switch” item is set to “Manual.” (p. 42) • Pauses the countdown until the assigned channel is automatically selected. • Select [RESUME] to resume the countdown. • The call is saved in the DSC Log. [ACPT] • Accepts the call. • The assigned channel is selected. • The call is saved in the DSC Log. [EXIT] Closes the All Ships call, and then returns to the operating screen. [INFO] The received call’s information is displayed. [IGN] • Ignores the call and returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. 37 DSC OPERATION D Receiving a Position Request call When a Position Request call is received: • The alarm sounds for 2 minutes. • “RCVD POS Request” is displayed. 1. 2. Push any software key to turn OFF the alarm. Push the software key below the intended operation. [ABLE] • Sends the Acknowledgement “Able to Comply.” • The call is saved in the DSC Log. [UNABL] • Sends the Acknowledgement “Unable to Comply.” • Displays the Acknowledgement information, and then returns to the operating screen by pushing the software key below [EXIT]. • The call is saved in the DSC Log. [ACPT] • Accepts the call. • Displays the received call’s information. • The call is saved in the DSC Log. • Push the software key below [ACK] to send the Position Reply call. (p. 33) [IGN] • Ignores the call and returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. NOTE: • If the Auto ACK function is set to “Auto,” the Position Reply is automatically sent to the calling station. (p. 42) • However, even if the Auto ACK function is set to “Manual,” after receiving a Distress Acknowledgement, or while in the Distress Cancel call procedure, the Position Reply is automatically sent to the calling station. 10 11 12 13 14 15 16 38 8 DSC OPERATION D Receiving a Test call TIP: By default, the Auto ACK function automatically sends an Acknowledgement to the calling station (p. 42). If the function is set to “Manual,” the following screens are displayed. When a Test call is received: • The alarm sounds for 2 minutes. • “RCVD Test Call” is displayed. 1. 2. Push any software key to turn OFF the alarm. Push the software key below your next operation. [IGN] • Ignores the call and returns to the operating screen. • The call is saved in the DSC Log. • “ ” blinks continuously until you display the call message. 39 [ABLE] • Sends the Acknowledgement “Able to Comply.” • The call is saved in the DSC Log. [ACPT] • Accepts the call. • Displays the received call’s information. • The call is saved in the DSC Log. • Push the software key below [ACK] to send a Test Acknowledgement call. (p. 32) • Push the software key below [RESEND] to resend. NOTE: If the Auto ACK function is set to “Auto,” the Test Acknowledgement call is automatically sent to the calling station when the call is received. (p. 42) DSC OPERATION ■ DSC Log D Receiving a Test Acknowledgement call After sending a Test call, the called station will send you a Test Acknowledgement call. When a Test Acknowledgement call is received: • The alarm sounds for 2 minutes. • “Received ACK” is displayed. Push any software key to turn OFF the alarm. • The received call’s information is displayed. • The call is saved in the DSC Log. LPush the software key below [EXIT] to return to the operating screen. D Received DSC Log The transceiver saves up to 50 received Distress call messages and 50 received “Others” call messages in your DSC Log. On the operating screen, “ ” is displayed when there is an unread call message. 1. Display the “DSC Log” screen. [MENU] ► “DSC Log” 2. Push [▲] or [▼] to select “Received,” and then push [ENT]. • The “Received” screen is displayed. 3. Push [▲] or [▼] to select “Distress” or “Others,” and then push [ENT]. L“Distress” displays the received Distress call log, and “Others” displays the received DSC call log. TIP: You can also display the “Received” screen by pushing the software key below on the operating screen. Continued on the next page. 10 11 12 13 14 15 16 40 8 DSC OPERATION D Received DSC log (Conitnued) 4. 5. Push [▲] or [▼] to scroll through the log. Push [ENT] to display the received call’s information. Received Distress log D Sent DSC Log The transceiver saves up to 50 DSC sent calls in your DSC Log. 1. Display the “DSC Log” screen. [MENU] ► “DSC Log” 2. Push [▲] or [▼] to select “Transmitted,” and then push [ENT]. • The “Transmitted” screen is displayed. 3. 4. Received DSC log [EXIT]: Returns to the operating screen. [DEL]: Deletes the selected call log. [POS]: LConirmation screen is displayed before deleting. Displays the position of the called station. LThis option is not displayed if no position data is received. [MMSI]: Saves the MMSI as an Individual ID. [WP]: Enters the received position as a Waypoint. (p. 47) 41 Push [▲] or [▼] to scroll through the log. Push [ENT] to display the sent call’s information. DSC OPERATION ■ DSC Settings On the “DSC Settings” screen, you can make settings on the DSC call related items. Position Input See “Entering the position and time” on page 21 for details. Individual ID See “Entering an Individual ID” on page 19 for details. Group ID See “Entering a Group ID” on page 20 for details. Auto ACK The Auto ACK function automatically sends an Acknowledgement call when the following calls are received. • Individual call (Default: Differs depending on the version) • Position Request call (Default: Manual) • Test call (Default: Auto) Manual: Manually send an Acknowledgement call. Auto: Automatically send an Acknowledgement call. TIP: When “Auto” is set to the Individual call, the Acknowledgement “Unable to Comply” is automatically sent when the call is received. CH Auto Switch (Default: Accept) Select whether or not to automatically switch to channel 16 or the speciied channel, or select whether to switch or ignore the call. Accept: After receiving a DSC call, the transceiver remains on the operating channel for 10 seconds. After that, the transceiver automatically switches to the channel that is speciied on the DSC call. Ignore: After receiving a DSC call, if you do not push the software key below [ACPT] in 10 seconds, the transceiver ignores the call, and then remains on the current operating channel. Manual: After receiving a DSC call, you can select whether or not to accept the received DSC call. DSC Switch (Default: On) Select whether or not to receive and send DSC calls. LYou can send Distress calls despite of this setting. On: Receives and sends DSC calls. Off (TEMP): Does not receive or send DSC calls until you turn OFF the transceiver. Off: Does not receive or send DSC calls. 10 11 12 13 14 15 16 42 8 DSC OPERATION ■ DSC Settings (Continued) Unread Return (Default: On) This function puts the received DSC call on hold while receiving another call. On: While receiving another call, the received DSC call is put on hold until the currently receiving call is hung up. Off: While receiving another call, the received DSC call is saved in the DSC Log. MOB Auto Set • MOB Key (Default: On (30 sec)) For 30 seconds after entering the MOB waypoint, this function automatically sets the Nature of Distress as “Man Overboard.” On (30 sec): The Nature of Distress is automatically set to “Man Overboard” for 30 seconds after entering the MOB waypoint. Off: The function is OFF. • Water Detection (Default: On (30 sec)) For 30 seconds after the transceiver has detected water, this function automatically sets the Nature of Distress as “Man Overboard.” On (30 sec): The Nature of Distress is automatically set to “Man Overboard” for 30 seconds after the transceiver has detected water. Off: The function is OFF. 43 Alarm Status Set the alarm ON or OFF for each DSC related item. • Safety (Default: On) An alarm sounds when a Safety DSC call is received. • Routine (Default: On) An alarm sounds when a Routine DSC call is received. • Warning (Default: On) An alarm sounds when: - no MMSI code is entered. - the position data has not been received for 2 minutes after turning ON the transceiver. - the received position data has not been updated for 10 minutes. - the received position data or manually entered position data has not been updated for 4 hours. • Self-Terminate (Default: On) An alarm sounds when duplicate Distress calls are received. • Discrete (Default: On) An alarm sounds when a lower priority call is received while receiving a high priority call. DSC OPERATION CH 70 SQL Level (Default: 5) Adjust the Squelch level for Channel 70 to between 1 and 10, or Open. L“ ” is displayed when adjusted to Open. A higher level blocks weak signals, which enables you to send a DSC call. DST at PW Off Loop Test This function sends DSC signals to the receiving AF circuit to compare the sending and receiving signals at the AF level. Push [ENT] to start the Loop Test. LWhen the sending and receiving DSC signals match, “OK” is displayed. (Default: Valid) This function enables you to send Distress calls even while the transceiver is OFF. You can send Distress calls by holding down [DISTRESS], even while the transceiver is OFF. Invalid: You cannot send Distress calls while the transceiver is OFF. Valid: NOTE: If “NG” is displayed, either or both the sending and receiving DSC circuits have a problem. In that case, you will have to send the transceiver to your dealer for repair. 10 11 12 13 14 15 16 44 9 OTHER FUNCTIONS ■ MOB (Man OverBoard) You can enter a Man OverBoard (MOB) waypoint into the transceiver with its GPS position data, as soon as a person has fallen into the water and needs to be rescued. This enables you to reach the MOB position even in the dark, or when you have lost visual contact. 1. 2. 1. 2. Push [◄] or [►] to display Hold down the software key below for 1 second to enter the MOB waypoint. 3. Push [◄] or [►] to display Push the software key below Push the software key below [NAV] to start the navigation, [DEL] to delete the entry, and [EXIT] to close the “MOB” screen. Navigating to the MOB waypoint: The transceiver can navigate you to the MOB waypoint. Push the software key below [NAV]. Push [ENT] to start the navigating to the entered point. LSee page 48 for navigation details. LSee page 48 for navigation details. LPush the software key below [EXIT] to stop the navigation and return to the operating screen. Deleting the MOB waypoint: 1. Push the software key below [DEL] to delete the MOB waypoint. • “Are you sure?” is displayed. 2. 45 MOB screen • The “MOB” screen is displayed. LYou can also display the “MOB” screen by selecting the “MOB” item on the Menu screen. L“No Entry” is displayed if no MOB waypoint is entered. Entering an MOB waypoint • After entering, “Man Overboard!” is displayed. LYou cannot enter the MOB waypoint if no GPS data is received. LYou can only enter 1 MOB waypoint, and the previously entered point is overwritten when a new waypoint is entered. 3. Push the software key below [OK] to delete. LYou can cancel the deletion by pushing the software key below [CANCEL] . • “No Entry” is displayed. OTHER FUNCTIONS ■ Waypoint Waypoints are GPS position data points of places you want to go to, the position of your own vessel, or of a vessel you received a DSC call from. You can enter up to 50 Waypoints with names of up to 10 characters. You can enter your current position information, or add one as a destination or landmarks you often go to, as information for easy access. 5. TIP: • Select a number or the compass direction using [▲]/[▼]/[◄]/[►]. • Push [ENT] to enter the selected number. • Select “←” or “→,” to move the cursor. • Push the software key below to select latitude, longitude, and name. D Entering a Waypoint Entering your current position as a Waypoint: 1. 2. Push [◄] or [►] to display Hold down the software key below for 1 second. TIP: • Select [! $ ?] to use characters, and select [ABC] to use numbers and letters. • Select characters or space using [▲]/[▼]/[◄]/[►]. • Push [ENT] to enter the selected character. • Select “←” or “→,” to move the cursor. Push [CLRé] to return to the operating screen. Manually entering a Waypoint: 1. 2. Push [◄] or [►] to display Push the software key below 2. • The “Waypoint” screen is displayed. 3. 4. Waypoint entry mode Entering a Waypoint name: 1. After editing the latitude and longitude, push the software key below [NEXT] to select “Name.” • “Waypoint was stored” is displayed. • The current position is entered as a Waypoint. LYou cannot register a Waypoint if no GPS data is received. 3. Edit the latitude and longitude. Push [◄] or [►] to display [ADD]. Push the software key below [ADD]. • Enters the Waypoint entry mode. • The current position is displayed in the entry boxes. Push the software key below to save the edited name. 10 11 12 13 14 15 16 46 9 OTHER FUNCTIONS ■ Waypoint (Continued) D Entering a received position D Waypoint screen After receiving a Distress call that includes position data, you can enter the position as a Waypoint. This enables you to reach the caller’s position. 1. 2. Push [◄] or [►] to display Push the software key below Push [▲] or [▼] to select “Distress.” Select the received call and then push [ENT]. • The received DSC call’s GPS position data is displayed on the “Information” screen. 5. Push [◄] or [►] to display [WP]. • “Store Waypoint?” is displayed. 6. Push the software key below [OK] to enter. Push [◄] or [►] to display Push the software key below 3. Push [◄] or [►] to scroll through [EXIT], [SORT], [NAV], [ADD], [EDIT], and [DEL]. Push [◄] or [►]. Sorting the Waypoint list: You can sort the Waypoint list by the Waypoint or MMSI name, or by the distance from your vessel. Push the software key below [SORT] to sort the list. • “▲” or “▼” is displayed next to “Name” or “DIST.” LEach push changes the sorting order. Navigating to a Waypoint: The transceiver can navigate you to an entered Waypoint. Push the software key below [NAV]. LSee page 48 for navigation details. • The position is entered on the “Waypoint” screen. 47 • The “Waypoint” screen is displayed. LYou can also display the “Waypoint” screen by selecting the “Waypoint” item on the Menu screen. • The “Received” screen is displayed. 3. 4. 1. 2. OTHER FUNCTIONS ■ Navigation Adding a Waypoint: Push the software key below [ADD] to add a Waypoint. LAdd the Waypoint in the same manner that is described in “Manually entering a Waypoint” on page 46. Editing a Waypoint: While selecting the Waypoint that you want to edit, push the software key below [EDIT] to edit the Waypoint. The Navigation function navigates from your current position to an entered regular Waypoint or MOB waypoint. Start navigating to the MOB waypoint: LThe MOB waypoint must be entered before navigating. 1. 2. Push [◄] or [►] to display Push the software key below • The “MOB” screen is displayed. LEdit the Waypoint in the same manner “Manually entering a Waypoint” on page 46 for editing a Waypoint. Deleting a Waypoint: 1. Select the Waypoint that you want to delete, and then push the software key below [DEL] to delete it. • “Are you sure?” is displayed. 2. Push the software key below [OK] to delete. LSelect [CANCEL] to cancel the deletion. 3. Push the software key below [NAV] to start navigating to the MOB waypoint. • The navigation starts. 10 11 12 13 14 15 16 48 9 OTHER FUNCTIONS D Navigation screen description ■ Navigation (Continued) Start navigating to a Waypoint: LA Waypoint must be entered before navigating. 1. 2. Push [◄] or [►] to display Push the software key below • The “Waypoint” screen is displayed. 3. 4. Push [▲] or [▼] to select a Waypoint. After selecting, push the software key below [NAV] to start navigating to the Waypoint. Range displays the radius of a compass circle. Push [▲] or [▼] to change the range between 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, and 12 nm. Displays the display’s direction type. Push the software key below [SEL] to select “N-UP,” “AC-UP,” or “WP-UP.” LSee page 57 for details. This lag icon indicates the direction to reach the target Waypoint or MOB waypoint. Displays the bearing of the target Waypoint or MOB waypoint from your vessel. Displays the distance to the Waypoint or MOB waypoint. Displays the Course Over Ground. Displays the Speed Over Ground. TIP: Once the navigation starts, it continues even if you close the Navigation screen by pushing the software key below [EXIT]. To properly inish the navigation, push the software key below [FINISH]. 49 OTHER FUNCTIONS ■ Compass ■ GPS/GNSS The Compass shows your vessel’s Course Over Ground (COG) and Speed Over Ground (SOG). 1. 2. Push [◄] or [►] to display Push the software key below • The “Compass” screen is displayed. Displays the display’s direction type. Push the software key below [SEL] to select “N-UP” or “AC-UP.” LSee page 57 for details. The GPS or GNSS “Status” screen displays the quantity, signal power, and position of the GPS satellites in the sky view. The screen also displays the direction, elevation angle, satellite numbers, and their received signal strength. TIP: Use the transceiver outdoors so the receiver has a clear view to receive GPS signals from the satellites. D GPS/GNSS Status screen Displaying the Status screen: 1. Push [MENU]. • The Menu screen is displayed. 2. Displays the Course Over Ground. Push the software key below [EXIT] to close the “Compass” screen, and return to the operating screen. Push [▲] or [▼] to select “GPS,” and then push [ENT]. • The “GPS” screen is displayed. L“GNSS” may be displayed, instead of “GPS,” depending on the transceiver version. Displays the Speed Over Ground. 3. 3. Push [▲] or [▼] to select “Status” and then push [ENT]. • The “Status” screen is displayed. 10 11 12 13 14 15 16 50 9 OTHER FUNCTIONS D GPS/GNSS Status screen (Continued) Sky view description: GPS mode* Your position • Image of the satellite Satellite A Elevation angle 90 degree line (Zenith) Elevation angle 60 degree line Elevation angle 30 degree line Elevation angle 0 degree line Sky view * “2D” is displayed while tracking 3 or less satellites. “3D” is displayed while tracking more than 4 or more satellites. z Push the software key below [DISP] to display the GPS/ GNSS status in the sky view or on the satellite signal strength status screen. z Push the software key below [EXIT] to return to the operating screen. Satellite signal strength status description: Satellite number Satellite signal strength level ●: Tracking satellite ○: Untracking satellite Satellite A Elevation angle 60 degree line Elevation angle 30 degree line Elevation angle 0 degree line 51 Elevation angle 90 degree line (Zenith) LThe untracking satellite numbers blink. LPush [▲] or [▼] to scroll through all the satellite numbers. OTHER FUNCTIONS ■ Information screen D GPS/GNSS Information screen Information screen description: 1. Push [MENU]. You can check your transceiver’s software version, GPS module version, and ATIS ID* on the “Information” screen. * Only for the Dutch and German versions. • The Menu screen is displayed. 2. 3. Push [▲] or [▼] to select “GPS,” and then push [ENT]. 1. • The “GPS” screen is displayed. L“GNSS” may be displayed, instead of “GPS,” depending on the transceiver version. 2. Push [MENU]. • The Menu screen is displayed. Push [▲] or [▼] to select “Information,” and then push [ENT]. • The “Information” screen is displayed. Push [▲] or [▼] to select “Information” and then push [ENT]. • The “Information” screen is displayed. LThe “Information” screen displays your position, date, time, Speed Over Ground (SOG), and Course Over Ground (COG). 3. Push the software key below [EXIT] to return to the operating screen. 10 11 12 13 14 15 16 52 10 MENU SCREEN ■ Using the Menu screen The Menu screen is used to set items, select options, and so on for the transceiver’s functions. 3. Push [▲] or [▼] to select “CHAN Group,” and then push [ENT]. • The “CHAN Group” screen is displayed. D Using the Menu screen Example: Setting the channel group to “INT.” 1. Push [MENU]. • The Menu screen is displayed. 4. Push [▲] or [▼] to select “INT,” and then push [ENT]. • “INT” is set and the transceiver returns to the previous screen. 2. Push [▲] or [▼] to select “Radio Settings,” and then push [ENT]. • The “Radio Settings” screen is displayed. LHolding down [▲] or [▼] sequentially scrolls up or down through the Menu screen. 53 LTo exit the Menu screen, push the software key below [EXIT]. LTo return to the previous screen, push [CLR é]. MENU SCREEN 10 ■ Menu screen items The Menu screen contains the following items. Radio Settings Item Compose Distress Item Ref. Undesignated Fire,Explosion Flooding Collision Grounding Capsizing p. 23 p. 23 p. 23 p. 23 p. 23 p. 23 Item Sinking Adrift Abandoning Ship Piracy Man Overboard — Ref. p. 23 p. 23 p. 23 p. 23 p. 23 — Compose Other Item Individual Call Group Call Ref. Item p. 25 All Ships Call p. 28 Test Call Ref. p. 29 p. 30 Waypoint (See pages 46 ~ 48 for details) MOB (See pages 45 for details) DSC Log Item Received Ref. Item p. 40 Transmitted Item Ref. Item p. 50 Information Ref. p. 55 p. 55 p. 55 p. 55 p. 55 Item Monitor Noise Cancel Call Channel FAV Settings RT Indicator Ref. p. 55 p. 56 p. 56 p. 56 p. 56 DSC Settings Item Position Input Individual ID Group ID Auto ACK CH Auto Switch DSC Switch Ref. p. 42 p. 42 p. 42 p. 42 p. 42 p. 42 Item Unread Return MOB Auto Set Alarm Status CH 70 SQL Level DST at PW Off Loop Test Ref. p. 43 p. 43 p. 43 p. 44 p. 44 p. 44 Coniguration Item Ref. p. 41 GPS/GNSS Status Scan Type* Scan Timer* Dual/Tri-watch* CHAN Group WX Alert* Ref. p. 52 Backlight Display Contrast Key Beep Key Assignment Direction Ref. p. 57 p. 57 p. 57 p. 57 p. 57 Item UTC Offset Inactivity Timer Float’n Flash Power Save — Ref. p. 57 p. 57 p. 57 p. 57 — 10 11 12 13 14 15 16 Information (See pages 52 for details) *May not be displayed, depending on the transceiver version. 54 10 MENU SCREEN ■ Radio Settings items Scan Type (Default: —) The transceiver has 2 scan types. Select Normal Scan and Priority Scan. • Normal Scan: Scans all Favorite channels in the selected channel group. • Priority Scan: Sequentially scans all Favorite channels, while monitoring Channel 16. LThe default setting differs, depending on the transceiver version. Scan Timer (Default: Off) You can use the Scan Timer to pause, or to resume after 5 seconds, when a signal is detected. (Default: —) Select the suitable channel group for your operating area. Select INT, USA, CAN, DSC, or ATIS depending on the transceiver version. LSee page 12 for details. WX Alert (Default: Off) For the USA, Australian, and Export versions, an NOAA broadcast station transmits a Weather Alert tone before any important weather information. L“WX L“WX ” is displayed instead of “WX.” ” blinks until you push a key after detecting an alert. • On: When a signal is detected on a channel, the scan pauses for 5 seconds, and then resumes. If the signal disappears in less than 5 seconds, the scan immediately resumes. • Off: When a signal is detected on a channel, the scan pauses until the signal disappears, and then resumes. • On with Scan: The preset Weather channels are sequentially checked while scanning. • On: The previously selected (last used) Weather channel is checked while scanning. • Off: The Weather Alert tone is not detected. Dual/Tri-watch Hold down [VOL/SQL] for 1 second to turn ON the Monitor function. The squelch opens. You can select whether the squelch closes when you release [VOL/SQL], or when you push any key. (Default: Dualwatch) Select Dualwatch or Tri-watch. • Daulwatch: Monitors Channel 16 while receiving on another channel. • Tri-watch: Monitors Channel 16 and the Call channel while receiving on another channel. LSee page 18 for details. 55 CHAN Group Monitor • Push: • Hold: (Default: Push) The squelch stays open while holding down [VOL/SQL]. The squelch stays open until you push any key. MENU SCREEN 10 Noise Cancel (Default: Off) The Noise Cancel function reduces random noise components in the received or transmitted signal. Set the function for both receiving and transmitting. RX • Off: The Noise Cancel function is OFF. • 1: Reduces random noise components in the received signal to approximately one half. • 2: Reduces random noise components in the received signal to approximately one third. • 3: Reduces random noise components in the received signal to approximately one tenth. FAV Settings You can set all channels as Favorite channels, clear all settings, or reset to default. By default, some channels are preset. The Favorite channels differ, depending on the transceiver version. • Set All Channels: Sets all channels as Favorite channels. • Clear All Channels: Clears all Favorite channels. • Set default: Resets Favorite channels to the default. LSee page 17 for details. RT Indicator (Default: On) TX • On: Reduces random noise components in the transmitted signal to approximately one third. • Off: The Noise Cancel function is OFF. Select whether or not to display the Radio Telephone indicator (RT) while in the RT mode. This indicates that while RT is displayed, you can make a voice communication, except for a DSC call. Call Chancel • On: • Off: (Default: —) You can change your Call channel. The default setting differs, depending on the transceiver version. LSee page 13 for details. The RT indicator is displayed. The RT indicator is not displayed. LWhen “On” is selected, “STBY” is displayed while in the standby mode, and “DSC” is displayed while in the DSC mode. 10 11 12 13 14 15 16 56 10 MENU SCREEN ■ Coniguration items Backlight Key Assignment Level (Default: 4) You can adjust the backlight brightness between 1 and 7, or OFF. The backlight automatically turns OFF after no key is pushed for 5 seconds. Softkey 1~21 You can change which software key functions to display, and their order. You can assign up to 21 software keys at a time. Continue Type (Default: Off) You can set the backlight on dim, even if the backlight is automatically turned OFF. This function enables you to see the display in the dark, even when the backlight is OFF. Set default Select this item to set the software key function order as default. • Off: The function is turned OFF. • Dim: The screen stays dimly lit, even if the backlight is turned OFF after no key is pushed for 5 seconds. LIf you want to reduce the battery consumption, turn this function OFF. Display Contrast (Default: 4) You can adjust the display contrast level between 1 and 8. One is the lowest contrast level, and eight is the highest contrast level. Key Beep (Default: On) You can select whether or not to sound a beep when a key is pushed. • On: Sounds a beep when a key is pushed. • Off: No beep sounds, for silent operation. 57 LThe usable software key functions and their order may differ, depending on the transceiver version. LThe default setting may differ, depending on the transceiver version. Direction You can set the display type for the “Compass,” “Navigation,” and “Position Check” screen. Compass (Default: N-UP) • N-UP: The top of the compass represents North. • AC-UP: The compass represents the direction of your course heading. Navigation (Default: N-UP) • N-UP: The top of the “Navigation” screen represents North. • AC-UP: The top of the “Navigation” screen represents the direction of your course heading. • WP-UP: The top of the “Navigation” screen represents the destination waypoint. MENU SCREEN 10 Position Check (Default: N-UP) • N-UP: The top of the “Position Check” screen represents North. • AC-UP: The top of the “Position Check” screen represents the direction of your course heading. UTC Offset (Default: 00:00) Set the offset time between Universal Time Coordinated (UTC) and your local time to between –14:00 and +14:00 (in 1 minute steps). Inactivity Timer The transceiver automatically returns to the operation screen if you push no key for the set period of time for each mode. Not DSC Related (Default: 10 min) This setting is for when the transceiver displays a screen that is not related to DSC. DSC Related (Default: 15 min) This setting is for when the transceiver displays a screen that is related to DSC. Distress Related (Default: Off) This setting is for when the transceiver displays a screen that is related to a Distress call. RT Related (Default: 30 sec) This setting is for when the transceiver is in the Radio Telephone mode. Float’n Flash The Float’n Flash function detects that the transceiver has come in contact with water. When the function turns ON, the backlight starts to blink to make it easy to find the transceiver, even in the dark. Function • On: The Float’n Flash function is ON. • Off: The Float’n Flash function is OFF. (Default: On) Auto Off (Default: 20 sec) After taking the transceiver out of the water, the backlight keeps blinking for this set period of time. Set the time to between 0 and 30 seconds (in 10 second steps). Cycle (Default: 0.5 sec) The backlight repeatedly turns ON or OFF in the set time cycle. Set the cycle to 0.5, 1, 2 or 4 seconds. Alarm (Default: Off) Select whether or not to sound an alarm while the backlight blinks when the Float’n Flash function is turned ON. • On: An alarm sounds while the backlight blinks. • Off: No alarm sounds, even when the Float’n Flash function is set to ON. Power Save 10 11 12 13 14 15 16 (Default: On) This function conserves battery power. The power save function is automatically turned ON when no signal is received for 5 seconds. Turn the Power Save function ON or OFF. 58 11 BATTERY CHARGING D Battery caution Misuse of Li-ion batteries may result in the following hazards: smoke, ire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery’s performance. R DANGER! NEVER solder the battery terminals, or NEVER modify the battery pack. This may cause heat generation, and the battery may burst, emit smoke or catch ire. R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a ire, overheating, or cause the battery to rupture. R DANGER! NEVER leave battery pack in places with temperatures above +60˚C (+140˚F). High temperature buildup in the battery, such as could occur near ires or stoves, inside a sun-heated vehicle, or in direct sunlight for long periods of time may cause the battery to rupture or catch ire. Excessive temperatures may also degrade battery’s performance or shorten battery life. R WARNING! NEVER use the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R DANGER! NEVER strike or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch ire. R DANGER! NEVER expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. R DANGER! NEVER place or leave battery packs near ire. Fire or heat may cause them to rupture or explode. Dispose of used battery packs in accordance with local regulations. R DANGER! NEVER use the battery with a transceiver for which it is not speciied. Never use a battery with any other equipment, or for any purpose that is not speciied in this instruction manual. 59 R DANGER! NEVER let luid from inside the battery get in your eyes. If it does, blindness can result. Rinse your eyes with clean water, without rubbing them, and immediately go to a doctor. R WARNING! NEVER let luid from inside the battery come in contact with your body. It it does, immediately wash with clean water. CAUTION: DO NOT use the battery pack out of the speciied temperature range. • IC-M93D: –20°C ~ +60°C (–4°F ~ +140°F) • IC-M93D EURO: –15˚C ~ +55˚C • BP-285: (–10˚C ~ +55˚C for the Australian version) –20°C ~ +60°C (–4°F ~ +140°F) Using the battery out of its speciied temperature range will reduce the battery’s performance and battery life. Please note that the speciied temperature range of the battery may exceed that of the transceiver. In such cases, the transceiver may not work properly because it is out of its operating temperature range. BATTERY CHARGING CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50°C (+122°F)) for an extended period of time. If the battery pack must be left unused for a long time, it must be detached from the transceiver after discharging. You may use the battery pack until the remaining capacity is about half, then keep it safely in a cool and dry place at the following temperature range: –20˚C ~ +50˚C (–4˚F ~ +122˚F) (within a month) –20˚C ~ +40˚C (–4˚F ~ +104˚F) (within three months) –20˚C ~ +20˚C (–4˚F ~ +68˚F) (within a year) BE SURE to replace the battery pack with a new one approximately ive years after manufacturing, even if it still holds a charge. The inside battery material will become weak after a period of time, even with little use. The estimated number of times you can charge the battery is between 300 and 500. Even when the battery appears to be fully charged, the operating time of the transceiver may become short when: • Approximately ive years have passed since the battery was manufactured. • The battery has been repeatedly charged. R WARNING! NEVER charge or leave the battery in the battery charger beyond the speciied time for charging. If the battery is not completely charged by the speciied time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the speciied time limit may cause a ire, overheating, or the battery may rupture. R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. NOTE: Charge the battery pack within the speciied temperature range: +10˚C ~ +45˚C (+50˚F ~ +113˚F). Otherwise, the charging time will be longer, but the battery will not reach a full charge. While charging, at a point after the temperature goes out of the speciied range, the charging will automatically stop. NOTE: Be sure the slots on the battery pack are correctly aligned with the guide tabs inside the battery charger. D Charging caution Guide tabs R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near ires or stoves, inside a sun-heated vehicle, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. R DANGER! NEVER charge the transceiver during a lightning storm. It may result in an electric shock, cause a ire or damage the transceiver. Always disconnect the power adapter before a storm. 11 10 11 12 13 14 15 16 Slot 60 11 BATTERY CHARGING ■ Regular battery charger D Installing the BC-220 D Charging with the BC-220 and BC-123S On a desktop You can charge Li-ion battery pack using the BC-220 and BC-123S. • Charging time: approximately 3 hours. On a wall Supplied screws LYou can also use the CP-25H cigarette lighter cable, or OPC-515L dc power cable instead of the BC-123S. Supplied screws CP-25H* (for a 12 V cigarette lighter sockect) or OPC-515L (for a 12 V power source) can be used instead of the BC-123S. Battery pack Turn OFF BC-220 BC-123S* power adapter 61 *A different type may be supplied, or may not be supplied, depending on the transceiver version. CAUTION: NEVER connect the OPC-515L to a power source using reverse polarity. This will damage the battery charger. White line: + / Black line: _ BATTERY CHARGING 11 ■ Optional battery charger D Rapid charging with the BC-214, BC-157S and AD-133 The optional BC-214 with the BC-157S and AD-133 simultaneously charges up to 6 Li-ion battery packs. • Charging time: approximately 3 hours. LYou can also use the OPC-656* dc power cable instead of the BC-157S and AD-133. Battery pack The charger adapters Turn OFF (AD-133) are installed in each slot. The type of the charger adapter differs, depending on the version of the BC-214. NEVER transmit near the BC-214 or the power adapter while charging. BC-157S ac adapter may not be supplied, depending on the version. BC-157S Status indicator (Individual indicators) BC-214 CAUTION: NEVER reverse the polarity when connecting the power cable to a power source. This will damage the battery charger. Red line: + / Black line: _ 10 11 12 13 14 15 16 OPC-656* *OPC-656 dc power cable Connect to a DC power source (12 ~ 16 V/at least 7 A) 62 12 OPTIONAL SPEAKER MICROPHONE ■ About the HM-165 Alligator type clip Attaches to your shirt, collar, pocket, and so on. PTT switch Push to transmit. Release to receive. Microphone Speaker ■ Attaching the HM-165 1. 2. Turn OFF the transceiver. Insert the speaker microphone into the connector, and then screw it tight, as shown below. LBe careful not to cross-thread the connection. CAUTION: Firmly attach the speaker microphone jack to prevent loss, or water immersion into the connector. Detaching: Rotate the jack cover, and then detach. Turn OFF the transceiver, when connecting the HM-165. NOTE: • NEVER immerse the connector in water. If the connector becomes wet, be sure to dry it BEFORE connecting it to the transceiver. • If the audio sound becomes mufled, remove any water that may be inside the speaker grill and/or microphone hole. • The microphone is near the top of the speaker microphone. To maximize the readability of your transmitted signal, hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, and then speak at your normal voice level. • The DSC alarms sound from the transceiver, even while the speaker microphone is attached. 63 Attaching: Attach the jack cover, and then irmly rotate it. NOTE: KEEP the jack cover attached when the speakermicrophone is not connected. Otherwise, water will get into the transceiver, and the terminals will become rusty, or if the connector gets wet, the transceiver may not work properly. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE You cannot turn ON the • The Battery is exhausted or over transceiver. discharged. • The Battery pack is not correctly attached. Little or no sound • The squelch level is set too high. comes from the • The volume level is set too low. speaker. • The speaker has been exposed to water. You cannot transmit • Water has entered to the speaker microphone connector. • Some channels are preset for low power or receive only by regulations. • The battery is exhausted. • The battery is overcharged. • The output power is set to low. Scan does not start No beeps sound • Favorite channels are not set. • Key Beep is set to OFF. You cannot send DSC calls You cannot receive GPS position data • MMSI (DSC self ID) code is not entered. • DSC Switch is set to OFF. • The built-in GPS antenna is obstructed, which interrupts the GPS signals from the satellites. 13 SOLUTION REF. • Recharge the battery pack. p. 61 • Correctly attach the battery pack. • Set the squelch to the threshold point. • Set the volume to a suitable level. • Remove the water using the AquaQuake function. • Dry the speaker microphone connector. p. 2 p. 13 • Change channels. p. 14 • Recharge the battery pack. • Conirm that the battery voltage is correct. • Push the software key below to select high power. • Set the Favorite channels. • Turn ON the Key Beep on the “Coniguration” screen. • Enter the MMSI (DSC self ID) code. • Turn ON the DSC Switch in the Menu. • Use the transceiver in a place where nothing interrupts the satellite signal. p. 61 p. 15 – p. 5 p. 17 p. 57 p. 9 p. 42 – 10 11 12 13 14 15 16 64 14 SPECIFICATIONS AND OPTIONS ■ Speciications IC-M93D D General • Frequency coverage: TX 156.025 ~ 157.425 MHz RX 156.050 ~ 163.275 MHz • Mode: FM (16K0G3E), DSC (16K0G2B) • Operating temperature range: –20°C ~ +60°C (–4°F ~ +140°F) • Current drain (approximately): Tx (5 W) 1.5 A Tx (1 W) 0.7 A RX maximum audio 0.25 A (External) 0.45 A (Internal) • Power supply requirement: 7.2 V DC nominal (negative ground) • Frequency stability: ±10 ppm • Antenna impedance: 50 ˘ nominal • Dimensions (approximately): 57 (W) × 144.6 (H) × 38.5 (D) mm (Projections not included) 2.2 (W) × 5.7 (H) × 1.5 (D) inches • Weight (approximately): 265 g/9.3 oz with BP-285 D Transmitter • Output power: • Modulation system: 5 W/1 W Variable reactance frequency modulation • Maximum frequency deviation: ±5.0 kHz • Adjacent channel power: 70 dB • Spurious emissions (typical): –68 dBc D Receiver • Sensitivity (typical): 0.25 µV (12 dB SINAD) • Squelch sensitivity (threshold, typical): 0.25 µV 65 • Intermodulation rejection ratio: 70 dB (typical) • Spurious response rejection ratio: 70 dB (typical) • Adjacent channel selectivity: 70 dB (typical) • Audio output power (at 10% distortion): 0.35 W typical (External) with an 8 ˘ load 0.9 W typical (Internal) with a 12 ˘ load at 1 kHz IC-M93D EURO D General • Frequency coverage: TX 156.000 ~ 161.450 MHz (156.000 ~ 161.600 MHz for Dutch version) Rx 156.000 ~ 163.425 MHz • Mode: FM (16K0G3E), DSC (16K0G2B) • Operating temperature range: –15°C ~ +55°C • Current drain (approximately): TX (5 W) 1.5 A TX (1 W) 0.7 A RX maximum audio 0.25 A (External) 0.45 A (Internal) • Power supply requirement: 7.2 V DC nominal (negative ground) • Frequency stability: ±1.5 kHz • Antenna impedance: 50 ˘ nominal • Dimensions (approximately): 57 (W) × 144.6 (H) × 38.5 (D) mm (Projections not included) • Weight (approximately): 265 g with BP-285 SPECIFICATIONS AND OPTIONS 14 D Transmitter • Output power: • Modulation system: 5 W/1 W Variable reactance frequency modulation • Maximum frequency deviation: ±5 kHz • Adjacent channel power: 70 dB • Spurious emissions: 0.25 µW • Power supply requirement: • Frequency stability: • Antenna impedance: • Dimensions (approximately): (Projections not included) • Weight (approximately): D Receiver D Transmitter • Sensitivity (typical): –6 dBµ emf at 20 dB SINAD • Squelch sensitivity (threshold, typical): –6 dBµ emf • Intermodulation rejection ratio: 68 dB • Spurious response rejection ratio: 70 dB • Adjacent channel selectivity: 70 dB • Audio output power (at 10% distortion): 0.2 W (External) with an 8 ˘ load 0.9 W typical (Internal) with a 12 ˘ load at 1 kHz IC-M93D EURO (Australian version) D General • Frequency coverage: TX 156.025 ~ 157.425 MHz RX 156.300 ~ 162.025 MHz • Mode: FM (16K0G3E), DSC (16K0G2B) • Operating temperature range: –10°C ~ +55°C • Current drain (approximately): TX (5 W) 1.5 A TX (1 W) 0.7 A RX maximum audio 0.25 A (External) 0.45 A (Internal) 7.2 V DC nominal (negative ground) ±10 ppm (–10°C ~ +55°C) 50 ˘ nominal 57 (W) × 144.6 (H) × 38.5 (D) mm 265 g/9.3 oz with BP-285 • Output power: • Modulation system: 5 W/1 W Variable reactance frequency modulation • Maximum frequency deviation: ±5.0 kHz • Adjacent channel power: 70 dB • Spurious emissions (typical): 0.25 µW D Receiver • Sensitivity (typical): –6 dBµ emf (20 dB SINAD) • Squelch sensitivity (threshold, typical): –6 dBµ emf • Intermodulation rejection ratio: 65 dB • Spurious response rejection ratio: 65 dB • Adjacent channel selectivity: 65 dB • Audio output power (at 10% distortion): 0.2 W (External) with an 8 ˘ load 0.9 W typical (Internal) with a 12 ˘ load at 1 kHz 10 11 12 13 14 15 16 66 14 SPECIFICATIONS AND OPTIONS ■ Options D Battery pack D Other • BP-285 Li-ion battery pack • HM-165/HM-228 speaker microphone Full sized waterproof speaker microphone including alligator type clip to attach to your shirt or collar. Battery pack BP-285 Voltage Capacity Battery life* 7.2 V 1485 mAh (minimum) 1570 mAh (typical) 9 hours * The operating periods are calculated under the following conditions; TX : RX : Standby = 5 : 5 : 90 (Power save : ON/ while valid GPS position data is received) D Chargers • BC-220 rapid charger + BC-123S ac adapter For rapid charging of battery pack. (Charging time: approximately 3 hours) • BC-214 rapid charger + AD-133 charger adapter (6 pcs.) + BC-157S ac adapter For rapid charging of 6 battery packs. (Charging time: approximately 3 hours) • FA-SC59V flexible antenna • MB-133 belt clip • MB-96F/MB-96FL leather belt hanger • CP-25H cigarette lighter cable For charging with the BC-220 charger through a 12 V cigarette lighter socket. NOTE: The CP-25H is equipped with a 1 A fuse. If the fuse blows, repair the problem, then replace it with a new rated fuse. DO NOT use fuses with amp ratings other than the ratings written below. D DC cables • opc-515l/opc-656 dc power cable For charging of the battery packs using a 12 V DC power source instead of the AC adapter. (OPC-515L for BC-220 : OPC-656 for BC-214) 67 Fuse CP-25H: (1 A /250 V) CHANNEL LIST 15 D For IC-M93D and IC-M93D EURO (Australia) Channel number USA INT CAN 01 01 01A 02 02 03 03 03A 04 04A 05 05A 05A 06 06 06 07 07A 07A 08 08 08 09 09 09 10 10 10 11 11 11 12 12 12 13*1 13 13*1 14 14 14 15*1 15*1 15*1 16 16 16 17*1 17 17*1 18 18A 18A 19 19A 19A 20 20*1 20 20A Frequency (MHz) Transmit Receive 156.050 160.650 156.050 156.050 156.100 160.700 156.150 160.750 156.150 156.150 156.200 160.800 156.200 156.200 156.250 160.850 156.250 156.250 156.300 156.300 156.350 160.950 156.350 156.350 156.400 156.400 156.450 156.450 156.500 156.500 156.550 156.550 156.600 156.600 156.650 156.650 156.700 156.700 156.750 156.750 156.800 156.800 156.850 156.850 156.900 161.500 156.900 156.900 156.950 161.550 156.950 156.950 157.000 161.600 157.000 157.000 *1 Low power only *3 For only the USA version Channel number USA INT CAN 21 21 21A 21A 21b 22 22A 22A 23 23 23A 24 24 24 25 25 25 25b 26 26 26 27 27 27 28 28 28 28b 60 60 61 61A 61A 62 62A 63 63A 64 64 64A 64A 65 65A 65A 65A 66 66A 66A 66A*1 67*1 67 67 Frequency (MHz) Transmit Receive 157.050 161.650 157.050 157.050 Rx only 161.650 157.100 161.700 157.100 157.100 157.150 161.750 157.150 157.150 157.200 161.800 157.250 161.850 Rx only 161.850 157.300 161.900 157.350 161.950 157.400 162.000 Rx only 162.000 156.025 160.625 156.075 160.675 156.075 156.075 156.125 160.725 156.125 156.125 156.175 160.775 156.175 156.175 156.225 160.825 156.225 156.225 156.275 160.875 156.275 156.275 156.325 160.925 156.325 156.325 156.375 156.375 *2 For only the Australian version *4 DSC operation only Channel number USA INT CAN 68 68 68 69 69 69 70*4 70*4 70*4 71 71 71 72 72 72 73 73 73 74 74 74 75*1 75*1 75*1 76*1 76*1 76*1 77*1 77 77*1 78 78A 78A 79 79A 79A 80 80A 80A 81 81A 81A 82 82A 82A 83 83 83A 83A 83b 84 84 84 84A 85 85 85 85A 86 86 86 Frequency (MHz) Transmit Receive 156.425 156.425 156.475 156.475 156.525 156.525 156.575 156.575 156.625 156.625 156.675 156.675 156.725 156.725 156.775 156.775 156.825 156.825 156.875 156.875 156.925 161.525 156.925 156.925 156.975 161.575 156.975 156.975 157.025 161.625 157.025 157.025 157.075 161.675 157.075 157.075 157.125 161.725 157.125 157.125 157.175 161.775 157.175 157.175 Rx only 161.775 157.225 161.825 157.225 157.225 157.275 161.875 157.275 157.275 157.325 161.925 Channel number USA INT CAN 86A 87 87 87 87A 88 88 88 88A 1019*3 1020*3 1078*3 Frequency (MHz) Transmit Receive 157.325 157.325 157.375 161.975 157.375 157.375 157.425 162.025 157.425 157.425 156.950 156.950 157.000 157.000 156.925 156.925 1079*3 156.975 156.975 161.975 161.975 162.025 162.025 A1*2 A2*2 WX channel 10 Frequency (MHz) Transmit Receive RX only 162.550 RX only 162.400 RX only 162.475 RX only 162.425 RX only 162.450 RX only 162.500 RX only 162.525 RX only 161.650 RX only 161.775 RX only 163.275 NOTE: Simplex channels, 3, 21, 23, 61, 64, 81, 82, and 83 CANNOT be lawfully used by the general public in USA waters. 10 11 12 13 14 15 16 68 15 CHANNEL LIST D For IC-M93D EURO ● International channels CH 01 02 03 04 05 06 07 08 09 10 Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) CH CH CH Transmit Receive Transmit Receive Transmit Receive Transmit Receive 156.050 160.650 11 156.550 156.550 21 157.050 161.650 61 156.075 160.675 156.100 160.700 12 156.600 156.600 22 157.100 161.700 62 156.125 160.725 156.150 160.750 13 156.650 156.650 23 157.150 161.750 63 156.175 160.775 156.200 160.800 14 156.700 156.700 24 157.200 161.800 64 156.225 160.825 156.250 160.850 15*1 156.750 156.750 25 157.250 161.850 65 156.275 160.875 156.300 156.300 16 156.800 156.800 26 157.300 161.900 66 156.325 160.925 156.350 160.950 17*1 156.850 156.850 27 157.350 161.950 67 156.375 156.375 156.400 156.400 18 156.900 161.500 28 157.400 162.000 68 156.425 156.425 156.450 156.450 19 156.950 161.550 37A*2 157.850 157.850 69 156.475 156.475 156.500 156.500 20 157.000 161.600 60 156.025 160.625 70*5 156.525 156.525 *1 Channels 15 and 17 may also be used for on-board communications provided the effective radiated power does not exceed 1 W, and subject to the national regulations of the administration concerned when these channels are used in its territorial waters. *2 UK Marina Channels: M1=37A (157.850 MHz), M2=P4 (161.425 MHz) for UK version only. 69 Frequency (MHz) Transmit Receive 71 156.575 156.575 72 156.625 156.625 73 156.675 156.675 74 156.725 156.725 75*3 156.775 156.775 76*3 156.825 156.825 77 156.875 156.875 78 156.925 161.525 79 156.975 161.575 80 157.025 161.625 CH Frequency (MHz) Frequency (MHz) CH Transmit Receive Transmit Receive 81 157.075 161.675 1019* 156.950 156.950 82 157.125 161.725 1020*4 157.000 157.000 83 157.175 161.775 1078* 156.925 156.925 84 157.225 161.825 1079* 156.975 156.975 85 157.275 161.875 2019* 161.550 161.550 161.600 161.600 2020* 86 157.325 161.925 87 157.375 157.375 2078* 161.525 161.525 CH 88 157.425 157.425 2079* 161.575 161.575 P4* 161.425 161.425 *3 The output power of channels 75 and 76 are limited to low power (1 W) only. The use of these channels should be restricted to navigation-related communications only and all precautions should be taken to avoid harmful interference to channel 16, for example by means geographical separation. *4 For only the Dutch version *5 DSC operation only CHANNEL LIST 15 D For IC-M93D EURO ● USA channels (for UK version only) CH 01A -03A -05A 06 07A 08 09 10 11 Frequency (MHz) Transmit Receive 156.050 156.050 ----156.150 156.150 ----156.250 156.250 156.300 156.300 156.350 156.350 156.400 156.400 156.450 156.450 156.500 156.500 156.550 156.550 CH 12 13*1 14 15*1 16 17*1 18A 19A 20 20A 21A Frequency (MHz) CH Transmit Receive 156.600 156.600 22A 156.650 156.650 23A 156.700 156.700 24 156.750 156.750 25 156.800 156.800 26 156.850 156.850 27 156.900 156.900 28 156.950 156.950 37A*2 157.000 161.600 61A 157.000 157.000 - 157.050 157.050 63A Frequency (MHz) Transmit Receive 157.100 157.100 157.150 157.150 157.200 161.800 157.250 161.850 157.300 161.900 157.350 161.950 157.400 162.000 157.850 157.850 156.075 156.075 ----156.175 156.175 CH 64A 65A 66A 67*1 68 69 70*3 71 72 73 74 Frequency (MHz) Transmit Receive 156.225 156.225 156.275 156.275 156.325 156.325 156.375 156.375 156.425 156.425 156.475 156.475 156.525 156.525 156.575 156.575 156.625 156.625 156.675 156.675 156.725 156.725 CH 75*1 76*1 77*1 78A 79A 80A 81A 82A 83A 84 84A Frequency (MHz) Transmit Receive 156.775 156.775 156.825 156.825 156.875 156.875 156.925 156.925 156.975 156.975 157.025 157.025 157.075 157.075 157.125 157.125 157.175 157.175 157.225 161.825 157.225 157.225 *1 Low power only *2 UK Marina Channels: M1=37A (157.850 MHz), M2=P4 (161.425 MHz) for UK version only. *3 DSC operation only NOTE: Simplex channels, 3, 21, 23, 61, 64, 81, 82, and 83 CANNOT be lawfully used by the general public in USA waters. Frequency (MHz) Transmit Receive 85 157.275 161.875 85A 157.275 157.275 86 157.325 161.925 86A 157.325 157.325 87 157.375 161.975 87A 157.375 157.375 88 157.425 162.025 88A 157.425 157.425 P4*2 161.425 161.425 CH 10 11 12 13 14 15 16 70 16 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy while transmitting. This radio is designed for and classiied as for “Occupational Use Only.” This means it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This W ARN ING radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC and IC RF exposure limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC KDB Publication 447498 D03, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. • The antennas, batteries, belt clips, speaker microphone, and other accessories that are listed in “OPTIONS” are authorized for use with this product. Use of accessories other than those speciied may result in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure.; Belt Clip (MB-133), Rechargeable Li-ion Battery Pack (BP-285). • Health Canada Safety Code 6 - Limits of Human Exposure to Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz. 71 To ensure that your expose to RF electromagnetic energy is within the FCC and IC allowable limits for occupational use, always adhere to the following guidelines: C AU TIO N • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna speciically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of the total radio use time (“50% duty cycle”). Transmitting more than 50% of the time can cause FCC and IC RF exposure compliance requirements to be exceeded. The radio is transmitting when the TX icon is displayed. You can cause the radio to transmit by pushing the “PTT” switch. • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting, and only use the Icom belt-clips listed in “OPTIONS” when attaching the radio to your belt, or other place, to ensure FCC and IC RF exposure compliance requirements are not exceeded. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates within the FCC and IC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. INDEX Accessories ..............................2 Alarm Status (DSC Settings) ....43 All Ships call Receiving ...........................37 Sending ..............................29 AquaQuake function ................15 ATIS ID ....................................10 Auto ACK (DSC Settings) ........42 Backlight (Coniguration) ........57 Battery Charger, optional................62 Charger, regular .................61 Indicator ...............................6 Installing/charging ..............61 Call Chancel Radio Settings....................56 Selecting ............................11 Setting ................................13 CH 70 SQL Level (DSC Settings) ....................44 CHAN Group (Radio Settings) ...55 Channel Favorite ..............................17 Group .................................12 List .....................................68 Name, editing .....................15 Selecting ............................11 Channel 16 ..............................11 CH Auto Switch (DSC Settings) ...42 Compass .................................50 Coniguration items..................57 Direction (Coniguration) ..........57 Display Contrast (Coniguration) ......57 Description ...........................5 Distress call Sending ..............................22 Receiving ...........................34 Cancel call .........................24 Regular call ........................23 Simple call..........................22 DSC Address ID .........................19 Receiving ...........................35 Sending ..............................25 Log, received .....................40 Log, sent ............................41 Settings ..............................42 Switch (DSC Settings) .........42 DST at PW Off (DSC Settings) ...44 Dual/Tri-watch (Radio Settings)..55 Dualwatch ................................18 Favorite channels, setting ......17 FAV Settings (Radio Settings)...56 Float’n Flash (Coniguration) ....58 GPS/GNSS ............................50 Information screen .............52 Status screen .....................50 Group call Receiving ...........................36 Sending ..............................28 Group ID Deleting/Entering ...............20 (DSC Settings) ...................42 HM-165, about/attaching........63 Inactivity Timer (Coniguration)..58 Individual Acknowledgement..............26 Call, receiving ....................35 Call, sending ......................25 ID, deleting .........................20 ID (DSC Settings) ..............42 ID, entering ........................19 Information screen ...................52 Key Assignment (Coniguration).....................57 Key Beep (Coniguration) .........57 Lock function ..........................14 Loop Test (DSC Settings) .........44 Menu Items ..................................54 Using ..................................53 MMSI code, entering .................9 MOB (Man OverBoard)............45 Auto Set .............................43 Deleting ..............................45 Entering..............................45 Navigating ..........................45 Monitor Function .............................15 (Radio Settings) .................55 Navigation ..............................48 Noise Cancel (Radio Settings) ..56 Options ...................................67 Panel description ......................4 Position Check (Coniguration) ............58 Entering..............................21 Input (DSC Settings) ..........42 Reply call, sending .............32 Request call, receiving .......38 Power Save (Coniguration) ....58 RT Indicator (Radio Settings) ....56 Scan Normal/Priority ...................16 Starting...............................17 Timer (Radio Settings).........55 Type (Radio Settings) ..........55 Types .................................16 Software keys ............................7 Speciications ..........................65 Squelch level ...........................13 Test Acknowledgement Receiving ...........................40 Sending ..............................31 Test call Receiving ...........................39 Sending ..............................30 Time, entering ..........................21 Transmitting (basic) .................14 Tri-watch ..................................18 Troubleshooting .......................64 Unread Return (DSC Settings) ...43 UTC Offset (Coniguration) .......58 Volume level............................13 Waypoint .................................46 Adding/Deleting/Editing......48 Entering..............................46 Entering, received position ...47 Name, entering ..................46 Navigating ..........................47 Screen................................47 Weather Alert/channels ....................12 Alert (Radio Settings) .........55 10 11 12 13 14 15 16 Radio Settings .........................55 Receiving (basic) .....................14 72 < Intended Country of Use > AT FI IT PL GB RO A-7316H-1EX Printed in Japan © 2016 Icom Inc. BE FR LV PT IS TR CY DE LT SK LI HR CZ GR LU SI NO DK HU MT ES CH EE IE NL SE BG 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan INFORMATION FCC RECOMMENDATION • POUR LES RAYONNEMENTS NON INTENTIONNELS DE CLASSE A: Cet équipement a été testé et reconnu conforme aux limites ixées pour un appareil numérique de classe A, conformément au point 15 de la réglementation FCC. Ces limites assurent une protection raisonnable contre les interférences nuisibles lorsque l'équipement est utilisé dans un environnement commercial. Cet équipement génère une énergie de radio fréquence, utilise et rayonner et s'il n'est pas installé et utilisé conformément au manuel d'instruction, peut causer des interférences nuisibles aux communications radio. Le fonctionnement de cet équipement dans une zone résidentielle est susceptible de causer des interférences nuisibles lorsque l'utilisateur doit corriger les interférences à ses propres frais. NETTOYEZ ENTIÈREMENT L'ÉMETTEUR-RÉCEPTEUR AVEC DE L'EAU DOUCE en cas d'exposition à l'eau de mer, et le sécher avant de l'utiliser. Autrement, les touches de l'émetteur-récepteur, les commutateurs et les contrôleurs risquent de devenir inutilisables,à cause de la cristallisation du sel, et/ou les bornes de recharge du bloc batterie risquent de rouiller. PRÉCAUTIONS ÉMETTEUR-RÉCEPTEUR VHF MARINE Merci d’avoir choisi un produit Icom. LIRE TOUTES LES PRÉCAUTIONS soigneusement et intégralement avant d’utiliser la radio. iM93D DÉFINITIONS EXPLICITES TERME R DANGER! R AVERTISSEMENT! MISE EN GARDE: Tout changement ou modification, non expressément approuvé par Icom Inc., peut annuler l'autorisation de l'utilisateur à utiliser cet appareil conformément à la réglementation FCC. MISE EN GARDE REMARQUE Cet appareil respecte les conditions établies au paragraphe 15 des règles de la FCC. Son utilisation est assujettie à la condition de ne pas provoquer des interférences nuisibles. DÉFINITION Risque d'accident mortel, de blessures corporelles graves ou d'explosion. Risque de blessures corporelles, d'incendie ou de choc électrique. Risque de dégât matériel. La non prise en compte peut entraîner des désagréments. Absence de risque de blessures corporelles, d'incendie ou de choc électrique. PRÉCAUTIONS REMARQUE: Si la protection étanche de l'émetteurrécepteur semble défectueuse, la nettoyer soigneusement avec un tissu mou et humide (d'eau douce), puis la sécher avant de l'utiliser. L'émetteurrécepteur risque de perdre sa protection étanche si le boitier, le capuchon du jack, ou le couvercle du connecteur est fêlé ou cassé, ou en cas de chute de l'émetteur-récepteur. NE PAS modiier la radio. Les spéciications peuvent changer et puis ne pas se conformer aux exigences d'un règlement correspondu. La garantie du radio ne couvre pas les problèmes résultant d'une modiication non autorisée. R DANGER! NE JAMAIS connecter les bornes du pack batterie en court-circuit. R DANGER! NE JAMAIS utiliser la radio près d'amorces électriques non blindées ni dans une atmosphère explosive. ATTENTION! La radio chauffe en cas d’utilisation continue sur une longue durée. R DANGER! Utiliser et charger exclusivement les packs batteries Icom spéciiés avec les portatifs Icom ou un chargeurs Icom. Seuls les packs batterie Icom sont testés et homologués pour une utilisation avec les radios Icom ou être chargés avec les chargeurs Icom. L'utilisation de packs batterie ou de chargeurs tiers ou de contrefaçon peut être à l'origine de fumées, d'incendie ou faire éclater la batterie. ATTENTION! La radio répond IPX7* exigences de protection étanche à l'eau. Mais lorsque la radio est tombé vers le bas, étanche à la protection imperméable à l'eau ne peuvent pas être garantis, parce que le cas de la radio ou le joint d'étanchéité peuvent être endommagés. R AVERTISSEMENT! NE JAMAIS utiliser l’appareil avec *Seulement lorsque le chapeau de la prise haut-parleur/ microphone, l'option HM-165 ou HM-228 est ixé. un casque ou d’autres accessoires audio réglés sur un niveau sonore élevé. Les spécialistes de l'audition mettent en garde contre toute utilisation prolongée à niveau sonore élevé. Si vous entendez une sonnerie baissez le niveau sonore ou interrompez l'utilisation. Même lorsque l’émetteur-récepteur est mis hors tension, un courant de très faible intensité circule dans ses circuits. Retirez la batterie de la radio quand ne pas l'utiliser pendant une longue période. Sinon, la batterie sera déchargée, et devra être rechargée ou remplacée. MISE EN GARDE: NE JAMAIS de nettoyer l’appareil avec des produits chimiques telsque l’essence ou l’alcool susceptibles d’endommager la surface de la radio. Assurez-vous de couper l'alimentation de la radio avant de brancher l'équipement fourni ou en option. MISE EN GARDE: NE JAMAIS tenir l’émetteur-récepteur par l’antenne pour le transport. Icom n'est pas responsable de la destruction ou des dommages sur l'émetteur-récepteur Icom, si le dysfonctionnement est causé par: • Force majeure, sans toutefois s'y limiter, les incendies, tremblements de terre, tempêtes, inondations, la foudre, ou autres catastrophes naturelles, perturbations, émeutes, guerre, ou contamination radioactive. • L'utilisation de l'émetteur-récepteur Icom avec tout équipement non fabriqué ou approuvé par Icom. Icom, Icom Inc. et le logo Icom sont des marques déposées de Icom Incorporated (Japon) au Japon, aux États-Unis, au RoyaumeUni, en Allemagne, en France, en Espagne, en Russie, en Australie, en Nouvelle-Zélande, et/ou dans d'autres pays. Tous les autres produits et toutes les autres marques sont des marques déposées ou non appartenant à leur titulaire respectif. ATTENTION! Même si le niveau de volume est bas , les bips du Float 'n Flash, DSC alarme et fonctions AquaQuake sont très bruyants. MISE EN GARDE: vériier que l'antenne lexible, batterie et cache de la prise sont solidement ixés à la radio, et que l'antenne et la batterie sont secs avant de ixation. Si vous exposez à l'intérieur de la radio à la poussière ou à l'eau, la radio sera remarquablement endommagé. VEILLEZ l'émetteur-récepteur est hors tension avant de connecter l'équipement fourni ou en option. ÉVITER d’utiliser ou de laisser la radio en plein soleil ou a une température ambiante inférieure a –20°C (–4°F) ou supérieure a +60°C (+140°F). Les opérations de base de la radio sont garantis dans la plage de température de fonctionnement spéciiée. Cependant, l'écran LCD peut ne pas fonctionner correctement après avoir été placés dans des zones extrêmement froides, ou une icône apparaît lors du fonctionnement de la radio pendant une longue période de temps. -1- -4- 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7316H-2US Printed in Japan © 2016 Icom Inc. PRÉCAUTIONS (suite) MISE EN GARDE: La longévité de la batterie peut être écourtée si elle est laissée de manière prolongée à pleine charge, entièrement déchargée, ou dans un environnement à température excessive (supérieure à +50°C (+122°F)). Si la batterie ne doit pas être utilisée pendant une assez longue période, elle doit être enlevée de la VHF une fois déchargée. Vous pouvez utiliser la batterie jusqu'à ce que le témoin de la batterie indique qu'elle est à la moitié de sa capacité. Placez-la ensuite dans un endroit frais et sec dans la plage de température ci-après : D Mise en garde concernant la batterie Un mauvais usage des batteries au Lithium ion peut avoir les conséquences suivantes: fumée, incendie ou explosion de la batterie. Il peut également causer des dommages a une autre batterie ou dégrader les performances de la batterie. R DANGER! NE JAMAIS souder les contacts de la batterie NI modiier sa composition. Ceci peut provoquer une surchauffe de la batterie, qui risque alors d'éclater, de fumer ou de prendre feu. –20°C ~ +50°C (–4°F ~ +122°F) (période inférieure à un mois) –20°C ~ +40°C (–4°F ~ +104°F) (période inférieure à trois mois) –20°C ~ +20°C (–4°F ~ +68°F) (période inférieure à une année) R DANGER! NE JAMAIS utiliser ni laisser le pack batterie à un emplacement où la température est supérieure à +60°C (+140°F). La montée en température de la batterie, comme cela peut survenir à proximité de lammes ou de poêles, à l'intérieur d'un véhicule exposé au soleil, ou en plein soleil peut détruire ou enlammer la batterie. Les températures excessives peuvent également dégrader les performances de la batterie ou réduire leur longévité. VEILLEZ à remplacer la batterie par une nouvelle après cinq ans, même si elle maintient la charge. Les matériaux présents à l'intérieur de la batterie se détériorent après un certain temps, même en cas d'utilisation réduite. Le nombre de fois où il est possible de charger la batterie est estimé entre 300 et 500 fois en fonction de l'utilisation. Même lorsque la batterie indique qu'elle est complètement chargée, le temps d'utilisation du poste peut être réduit dans les cas suivants: R DANGER! NE PAS marteler ni cogner la batterie d’une quelconque façon. N'utilisez pas la batterie si elle a reçu des impacts ou a été jetée ou si elle a subi une forte pression. Les dommages subis par une batterie peuvent ne pas être visibles de l'extérieur du boîtier. Même si la surface de la batterie ne semble pas issurée ou endommagée, les cellules à l'intérieur de la batterie peuvent se rompre ou prendre feu. • Sono passati approssimativamente cinque anni dalla data di fabbrica della batteria. • La batteria è stata ripetutamente caricata. INFORMATION SUR LA FORMATION À LA SÉCURITÉ Votre radio Icom produit une énergie électromagnétique de radiofréquences (RF), en mode de transmission. Cette radio est conçue pour un «usage professionnel seulement» et classée comme tel, ce qui signifie qu’elle doit être utilisée uniquement dans le cadre d’un travail par des personnes conscientes des dangers et des mesures visant à minimiser ces dangers. Elle N’EST PAS conçue pour une «utilisation grand public», dans un environnement non contrôlé. Cet appareil a été évalué et jugé conforme, aux limites d’exposition aux RF de la FCC et d’IC, pour une «utilisation grand public». En outre, votre radio Icom satisfait les normes et directives qui suivent en matière de niveaux d’énergie et d’énergie électromagnétique de RF et d’évaluation de tels niveaux en ce qui concerne l’exposition humaine: • Publication 447498 D03 de la FCC KDB, «Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields». • Norme de l’American National Standards Institute (ANSI): IEEE C95.1-1992 sur les niveaux de sécurité compatibles avec l’exposition humaine aux champs électromagnétiques de radiofréquences (3 kHz à 300 GHz). • Norme de l’ANSI: IEEE C95.3-1992 sur la méthode d’évaluation recommandée du champ magnétique potentiellement dangereux des radiofréquences et des micro-ondes. • Les accessoires illustrés dans “OPTIONS” de la feuille d'instructions sont approuvés pour une utilisation avec ce produit. L’utilisation d’accessoires autres que ceux précisés peut entraîner des niveaux d’exposition aux RF supérieures aux limites établies par la FCC et d’IC en matière d’exposition aux RF sans il. • Le Code de sécurité 6 de Santé Canada - Les limites d’exposition humaine à l’énergie électromagnétique dans la gamme de fréquences de 3 kHz à 300 GHz. D Mise en garde concernant la recharge R DANGER! NE JAMAIS charger le pack batterie à des endroits exposés à des températures extrêmement élevées, comme à proximité de lammes ou de poêles, à l'intérieur d'un véhicule exposé au soleil, ou en plein soleil. Dans ces environnements, le circuit de sécurité/protection à l'intérieur de la batterie peut s'activer et interrompre la recharge de la batterie. R DANGER! NE PAS exposer la batterie à la pluie, la neige, l’eau de mer ou tout autre liquide. Ne pas charger ou utiliser une batterie humide. Si une batterie est humide, veillez à l'essuyer complètement avant de l'utiliser. R DANGER! Tenir à l'écart batteries au feu. Feu ou la chaleur peut provoquer une rupture ou d'exploser. Disposer de batteries utilisées conformément à la réglementation locale. R AVERTISSEMENT! NE JAMAIS charger l'émetteur- récepteur durant un orage. Cela risquerait de provoquer un choc électrique, un incendie ou d'endommager l'émetteurrécepteur. Toujours débrancher l'adaptateur de courant avant une tempête. R DANGER! Utiliser la batterie uniquement avec la radio pour lequel elle est spéciiée. Ne jamais utiliser une batterie avec tout autre équipement ou pour une autre destination que celle spéciiée dans le présent manuel d'utilisation. R AVERTISSEMENT! NE JAMAIS charger ou laisser la batterie dans le chargeur de batterie au-delà de la durée de charge indiquée. Si la batterie n'est pas complètement chargée pendant le temps spéciié, interrompez la recharge et retirez la batterie du chargeur de batterie. La poursuite de la charge au-delà de durée indiquée peut provoquer un incendie, une surchauffe ou l’éclatement de la batterie. R DANGER! Dans le cas où du liquide provenant de l'intérieur de la batterie entre dans vos yeux, vous risquez la cécité. Rincez abondamment les yeux à l'eau courante, sans les frotter et consultez immédiatement un médecin. R AVERTISSEMENT! NE JAMAIS mettre la batterie dans un four à micro-ondes, un récipient haute-pression ou dans un four à induction. Ceci peut provoquer un incendie, une surchauffe ou détériorer la batterie. R AVERTISSEMENT! NE JAMAIS insérer un émetteurrécepteur humide ou poussiéreux (avec sa batterie) dans le chargeur. Ceci peut corroder les bornes du chargeur de la batterie ou endommager le chargeur. Le chargeur n'est pas étanche. R AVERTISSEMENT! Cessez immédiatement d'utiliser la batterie si elle dégage une odeur anormale, si elle surchauffe, est décolorée ou déformée. Si l'une de ces situations se produit, contactez votre revendeur ou distributeur Icom. REMARQUE: Charger la batterie à l'intérieur de la plage de températures spéciiée de +10˚C à +45˚C (+50˚F à +113˚F). Sinon, le temps de charge sera plus long, mais la batterie ne sera pas atteindre une charge complète. La charge s'arrête automatiquement lorsque la température est hors de la plage spéciiée. R AVERTISSEMENT! Lavez immédiatement à l'eau courante toute partie du corps qui est entrée en contact avec le liquide provenant de l'intérieur de la batterie. MISE EN GARDE: Toujours utiliser la batterie dans la plage de température spéciiée, comprise entre –20°C et +60°C (–4°F à +140°F), et de la batterie elle-même de –20°C à +60°C (–4°F à +140°F). L’utilisation de la batterie hors de la plage de température indiquée, a pour effet d’en altérer les performances et d’en réduire la durée de vie. Ain de vous assurer que votre exposition à une énergie électromagnétique de RF se situe dans les limites permises par la FCC et d’IC pour une utilisation grand public, veuillez en tout temps respecter les directives suivantes: NE PAS faire fonctionner la radio sans qu’une antenne appropriée y soit ixée, car ceci risque d’endommager la radio et causer une exposition supérieure aux limites établies par la FCC et d’IC. L’antenne appropriée est celle qui est fournie avec cette radio par le fabricant ou une antenne spécialement autorisée par le fabricant pour être utilisée avec cette radio. NE PAS émettre pendant plus de 50 % du temps total d’utilisation de l’appareil («50 % du facteur d’utilisation»). La notion «50% du facteur d’utilisation» s’applique également au mode VOX/PTT. Émettre pendant plus de 50 % du temps total d’utilisation peut causer une exposition aux RF supérieure aux limites établies par la FCC et d’IC. Lorsque l'icône TX est afiché, cette radio est en train d’émettre. La radio émettra si vous appuyez sur le bouton PTT. TOUJOURS tenir l’antenne éloignée d’au moins 2,5 cm de votre corps au moment d’émettre et utiliser uniquement l’attache pour ceinture Icom illustrée dans “Options” de la feuille d'instructions, lorsque vous attachez la radio à votre ceinture, ou à autre chose, de façon à vous assurer de ne pas provoquer une exposition aux RF supérieure aux limites ixées par la FCC et d’IC. Pour offrir à vos interlocuteurs la meilleure qualité de transmission possible, tenez l’antenne à au moins 5 cm de votre bouche et légèrement de côté. Les renseignements ci-dessus fournissent à l’utilisateur toute l’information nécessaire sur l’exposition aux RF et sur ce qu’il faut faire pour assurer que cette radio fonctionne en respectant les limites d’exposition aux RF établies par la FCC et d’IC. Interférence électromagnétique et compatibilité En mode de transmission, votre radio Icom produit de l’énergie de RF qui peut provoquer des interférences avec d’autres appareils ou systèmes. Pour éviter de telles interférences, mettez la radio hors tension dans les secteurs où une signalisation l’exige. NE PAS faire fonctionner l’émetteur dans des secteurs sensibles au rayonnement électromagnétique tels que les hôpitaux, les aéronefs et les sites de dynamitage. REMARQUE: Veillez que les fentes de la batterie sont correctement alignées avec les pattes de guidage à l'intérieur du chargeur de batterie. -2- -3-
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract Author : Icom Inc. Create Date : 2016:07:06 15:25:49+09:00 Modify Date : 2016:07:08 12:49:00-04:00 Subject : XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:07:08 12:49-04:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:6ccbf169-3cfd-4fb4-8ae8-7325b1773046 Original Document ID : adobe:docid:indd:e9c48cae-ad38-11e2-8953-9f7a4d84e34e Document ID : xmp.id:10C3597B4243E611941CFF0A8A0E1E87 Rendition Class : proof:pdf Version ID : 1 Derived From Instance ID : xmp.iid:4C77D2BFBC41E611ADE1BB43F186700F Derived From Document ID : xmp.did:F297CB2FFB0FE611A112A97FE26DCC97 Derived From Original Document ID: adobe:docid:indd:e9c48cae-ad38-11e2-8953-9f7a4d84e34e Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:07:06 15:25:49+09:00 Format : application/pdf Title : IC-M93D_M93D_EURO_0 Creator : Icom Inc. Description : Light Source : Unknown Startup Profile : Print Producer : Adobe PDF Library 10.0.1 Trapped : False GTS PDFX Version : PDF/X-1:2001 GTS PDFX Conformance : PDF/X-1a:2001 Page Count : 82EXIF Metadata provided by EXIF.tools