ICOM orporated IC-F30G Handheld Transmitter held to face User Manual IC F30G series

ICOM Incorporated Handheld Transmitter held to face IC F30G series

UserManual.wiki >

ICOM orporated >

IC-F30G User Manual >

Manual HTML Version

Manual

INSTRUCTION MANUAL

VHF TRANSCEIVER

UHF TRANSCEIVER

iF40GT/GS

iF30GT/GS

This device complies with Part 15 of the FCC rules. Oper-

ation is subject to the following two conditions: (1) This de-

vice may not cause harmful interference, and (2) this

device must except any interference received, including in-

terference that may cause undesired operation.

FOREWORD

Thank you for purchasing the IC-F30GT/GS,IC-F40GT/GS FM

transceiver.

READ ALL INSTRUCTIONS carefully and completely before using

the transceiver.

SAVE THIS INSTRUCTION MANUAL–This instruction manual

contains important operating instructions for the transceiver.

INSTALLATION NOTES

• When transmitting with a portable radio, hold the radio in a vertical

position with its microphone 2.5 to 5 centimeters (1 to 2 in.) away

from your mouth. Keep the antenna at least 2.5 centimeters (1 in.)

from your head and body.

• If you wear a portable two-way radio on your body, ensure that the

antenna is at least 2.5 centimeters (1 in.) from your body when

transmitting.

IMPORTANT

RCAUTION! NEVER hold the transceiver so that the antenna is

very close to, or touching exposed parts of the body, especially the

face or eyes, while transmitting. The transceiver will perform best if

the microphone is 2 to 4 in. (5 to 10 cm) away from the lips and the

transceiver is vertical.

RCAUTION! NEVER operate the transceiver with a headset or

other audio accessories at high volume levels.

RCAUTION! NEVER short the terminals of the battery pack.

DO NOT push the PTT when not actually desiring to transmit.

AVOID using or placing the transceiver in direct sunlight or in areas

with temperatures below +14°F (–10°C) or above +122°F (+50°C).

The basic operations, transmission and reception of the transceiver,

are guaranteed within the specified operating temperature range

(depending on version). However, the LCD display may not be op-

erate correctly, or show an indication in the case of long hours of

operation, or after being placed in extremely cold areas.

DO NOT modify the transceiver for any reason.

KEEP the transceiver from the heavy rain, and Never immerse it in

the water. The transceiver construction is water resistant, not wa-

terproof.

The use of non-Icom battery packs/chargers may impair transceiver

performance and invalidate the warranty.

FCC caution: Changes or modiﬁcations to this transceiver, not

expressly approved by Icom Inc., could void your authority to op-

erate this transceiver under FCC regulations.

iii

TABLE OF CONTENTS

FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

INSTALLATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i–ii

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

1 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2–4

‘Switches, controls, keys and connectors . . . . . . . . . . . . . . . . .2–3

‘Function display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 BATTERY PACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–10

‘Battery pack replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

‘Battery cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

‘Battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7–8

‘ Charging NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

‘ Battery case (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4 PROGRAMMABLE FUNCTIONS . . . . . . . . . . . . . . . . . . . . . .11–15

‘General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

5 CONVENTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . .16–18

‘Receiving and transmitting . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

‘Call procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

‘Tx code channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

‘Manual 5-tone codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

‘Transmitting notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

6 SmarTrunk IITM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . .19–21

‘Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

7 OTHER FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

‘DTMF pager/Code squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

8 OPTIONAL UNIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . .23

‘ Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

9 CLONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

10 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25–26

11 MEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

ACCESSORIES

‘‘Accessory attachment

DSupplied accessories

The transceiver comes supplied with the following accessories.

qFlexible antenna (may

differ according to ver-

sion)

wBelt clip

DAntenna

The antenna screws onto the transceiver

as illustrated at right.

DBelt clip

Attach the belt clip to the transceiver as illustrated below.

To release the belt clip

To attach the belt clip

PANEL DESCRIPTION

‘‘Switches, controls, keys and connectors

DDProgrammable key reference

Microphone

Speaker

F0 (Red)

F1 (Black)

F2 (Black)

F3 (Black)

PANEL DESCRIPTION

qANTENNA CONNECTOR

Connects the supplied antenna.

wDEALER-PROGRAMMABLE KEY [F0 (Red)]

eDEALER-PROGRAMMABLE KEY [F1 (Black)]

rPTT SWITCH [PTT]

Push and hold to transmit; release to receive.

tDEALER-PROGRAMMABLE KEYS [F2 (Black)], [F3 (Black)]

• Push to select the operating channel.

• Can be programmed as [ ✱]/[ # ]. (SmarTrunk mode only)

yDEALER-PROGRAMMABLE KEYS [P0]/[P1]/[P2]/[P3]

Can each be programmed for one of several functions by your

Icom Dealer.

u10-KEY PAD (IC-F30GT/IC-F40GT only)

Used to enter DTMF codes, the operating channel, etc.

iFUNCTION DISPLAY

Displays variety of information such as, operating channel num-

ber/names, 5-tone code, remaining battery power, DTMF num-

bers, transmit output power setting, Audible indication, etc.

NOTE: Above functions depend on pre-setting.

oMULTI CONNECTOR

Connect optional speaker-microphone, etc..

!0 TRANSMIT/BUSY INDICATOR

Lights red while transmitting; lights green while receiving a sig-

nal, or squelch is open.

!1 VOLUME CONTROL [VOL]

Turns power ON and adjusts the audio level.

!2 ROTARY SELECTOR [SEL]

Selects operating channel or bank. Depends on setting.

PANEL DESCRIPTION

‘‘Function display

qSIGNAL STRENGTH METER

Indicates relative signal strength level.

wBANK NUMBER INDICATOR

Indicates operating bank (channel group) number.

eLOW POWER INDICATOR

Appears when low output power is selected.

rMULTI-FUNCTION INDICATOR

Indicates operating channel number, channel names, 5-tone

code, etc., according to operating condition.

tSCRAMBLER INDICATOR

Appears while the voice scrambler function is activated.

yKEY LOCK INDICATOR

Appears during key lock function ON.

uBELL INDICATION

Appears or blinks when a 2/5Tone call is received.

iAUDIBLE INDICATOR

Appears when monitor function is turned ON. (CTCSS and

DTCS mutes are released.)

oBATTERY INDICATOR

Indicates remaining battery power.

BATTERY PACKS

‘‘Battery pack replacement

Before replacing the battery pack, the volume control MUST be ro-

tated fully counterclockwise, until a click is heard, to turn the power

OFF.

• Slide the battery release forward, then pull the battery pack up-

ward with the transceiver facing you.

DDBATTERY PACKS

*1Battery life is calculated under the following conditions;

Tx : Rx : standby =5 : 5 : 90

* Operating period depends on alkaline cells used.

Charging period

Battery Voltage Capacity BC-119 or Battery life*

pack BC-137 BC-121

with AD-94

BP-208 Battery case for AA N/A N/A —

(R6)×6 alkaline

BP-209 7.2 V 1100 mAh 15 hrs. 1.5 hrs. 7 hrs.

BP-210 7.2 V 1650 mAh 15 hrs. 2.0 hrs. 11 hrs

3BATTERY PACKS

‘‘Battery cautions

• CAUTION! NEVER short terminals (or charging terminals) of the

battery pack. Also, current may flow into nearby metal objects

such as a necklace, so be careful when placing battery packs (or

the transceiver) in handbags, etc.

Simply carrying with or placing near metal objects such as a neck-

lace, etc. causes shorting. This will damage not only the battery

pack, but also the transceiver.

• NEVER incinerate used battery packs. Internal battery gas may

cause an explosion.

• NEVER immerse the battery pack in water. If the battery pack be-

comes wet, be sure to wipe it dry BEFORE attaching it to the

transceiver.

• Clean the battery terminals to avoid rust or miss contact.

• Keep battery contacts clean. It’s a good idea to clean battery ter-

minals once a week.

If your battery pack seems to have no capacity even after being

charged, completely discharge it by leaving the power ON

overnight. Then, fully charge the battery pack again. If the battery

pack still does not retain a charge (or only very little charge), a new

battery pack must be purchased. (p. 9)

DDRecycling information (U.S.A. only)

The product that you have purchased contains a

rechargeable battery. The battery is recyclable. At

the end of its life, under various state and local

laws, it may be illegal to dispose of this battery into

the municipal waste stream. Call 1-800-822-8837

for battery recycling options in your area, or contact

your dealer.

BATTERY PACKS

‘‘Battery charging

DRapid charging with the BC-119+AD-94 (#02)

The optional BC-119 provides rapid charging of optional battery

packs.

The following are additionally required:

• One AD-94 (#02).

• An AC adapter (may be supplied with the BC-119 depending on ver-

sion).

When using the BC-119 in a vehicle: If the charge indicator

ﬂashes orange, the vehicle battery voltage is low and charging

may not be performed. Check the vehicle battery voltage in this

case. If the charge indicator ﬂashes red, there may be a prob-

lem with the battery pack (or charger). Re-insert the battery pack

or contact your dealer.

BC-119

+ AD-94 #02

Check orientation

for correct charg-

ing. (Insert togeth-

er with charging

adapter.)

Turn power

OFF.

3BATTERY PACKS

DRapid charging with the BC-121+AD-94 (#02)

The optional BC-121 allows up to 6 battery packs to be charged si-

multaneously. The following are additionally required.

• Six AD-94 (#02).

•

An AC adapter

(may be supplied with the BC-121 depending on version)

DRegular charging with

the BC-137

The optional BC-137 pro-

vides regular charging of

optional battery pack with/

without transceiver.

The following is addition-

ally required:

• An optional AC adapter.

(A charger adapter is sup-

plied with BC-137.)

MULTI-CHARGER

AC adapter

(purchased

separately) Charge indicator

(each indicator functions independently)

Turn power OFF.

Check orientation

for correct charg-

ing. (Insert togeth-

er with charging

adapter.)

Turn power OFF.

BC-137

BATTERY PACKS

‘‘Charging NOTE

Prior to using the transceiver for the ﬁrst time, the battery pack must

be fully charged for optimum life and operation.

• Recommended temperature range for charging:

+10°C to +40°C (50°F to 140°F).

• Use the supplied charger or optional charger (BC-119/BC-121 for

rapid charging, BC-137 for regular charging) only. NEVER use other

manufacturers’ chargers.

The optional BP-209 or BP-210 battery packs include rechargeable

Ni-Cd (Ni-MH: BP-210) batteries and can be charged approx. 300

times. Charge the battery pack before ﬁrst operating the transceiver

or when the battery pack becomes exhausted.

If you want to charge the battery pack more than 300 times, the fol-

lowing points should be observed:

• Avoid over charging. The charging period should be less than

48 hours.

• Use the battery until it becomes almost completely exhausted

under normal conditions. We recommend battery charging after

transmitting becomes impossible.

DDBattery pack life

When the operating period becomes extremely short, even after

charging the battery pack fully, a new battery pack is needed.

3BATTERY PACKS

‘‘Battery case (Option)

When using an optional BP-208

BATTERY CASE

attached to the

transceiver, install 6 AA (R6) size alkaline batteries as illustrated

below.

DDCAUTION

• Use ALKALINE batteries only.

• Make sure all battery cells are the same brand, type and ca-

pacity.

• Never mix old and new batteries.

Either of the above may cause a fire hazard or damage the

transceiver if ignored.

• Never incinerate used battery cells since internal battery gas

may cause them to rupture.

• Never expose a detached battery case to water.

If the battery case gets wet, be sure to wipe it dry before use.

PROGRAMMABLE FUNCTIONS

‘‘General

In the following explanations, programmable function names are

bracketed, the speciﬁc switch used to activate the function depends

on programming.

DDKEYPAD LOCK FUNCTION

This function locks access to all programmable switches (except

the switch assigned for the lock function).

Push and hold the [Lock] switch for 1 sec. to toggle the lock function

ON and OFF.

• “ ”appears while the lock function is ON.

• This function may be inhibited on some channels.

DDPRIORITY CHANNEL

This function is used to select a pre-programmed channel at the

push of a switch.

Push the [Priority A/A (Rewrite)/B] switch to select the priority chan-

nel.

• “Prio A” or “Prio B”appears briefly, then the priority channel is auto-

matically selected.

DDSCAN FUNCTION

The scan function allows you to search a pre-programmed group

of channels for signals.

Push the [Scan A/B] switch to start/stop scan.

• Scan pauses on a channel when receiving a signal.

• Depending on programming, a message may appear while scanning.

• “Lockout SCAN” (pre-programmed list SCAN) or “Priority SCAN” can

be pre-programmed.

• When the “Power-save function” is activated, the transceiver checks

all pre-programmed channels then returns to the “Power-save func-

tion” again.

4PROGRAMMABLE FUNCTIONS

DDHIGH/LOW POWER OUTPUT

This function selects high or low power for a channel.

Push the [High/Low] switch to change transmit output power be-

tween high, low1 and low2 power.

• “ ” appears when low1 or low2 output power is selected.

DDSCRAMBLER FUNCTION

(optional UT-109 (#02)* or UT-110 (#02)* is required.)

This function provides higher communication security.

UT-109: Non-rolling type. 32 code numbers are available.

UT-110: Rolling type. 1020 (4 groups ×255) code numbers are

available.

Push the [Scrambler] switch to toggle the function ON and OFF.

NOTE: NEVER use #01 Low AF level versions, as they are not

compatible

PROGRAMMABLE FUNCTIONS

DDMONITOR AUDIBLE FUNCTION

The monitor function allows you to open the transceiver’s squelch

manually to check whether a channel is busy or not. The trans-

ceiver has 2 conditions for receive standby:

Audible condition:

This condition mutes audio ONLY when

no carrier is present. You can receive (or

monitor) any signals on a channel.

• Push and hold the [Moni] (LMR) or

[Moni (Audi)] (PMR) switch to select the

audible condition.

Any audio mute functions are cancelled

while pushing the [Moni] (LMR) or

[Moni (Audi)] (PMR) switch.

Inaudible condition:

This condition mutes ALL signals except

those directed to you. Therefore you

should check a channel’s condition (busy

or not) with the monitor function before

transmitting.

• Push the [Moni] (LMR) or [Moni (Audi)]

(PMR) switch momentarily to select the in-

audible condition.

DDTALK AROUND

The talk around function changes duplex channels to simplex chan-

nels.

• Duplex allows you to contact your base station, repeaters, etc.

• Simplex allows you to contact other portable transceivers directly

(portable-to-portable contact).

Push the [Talk Around] switch to toggle the function ON and OFF.

All signals are received.

Only signals containing the

proper tone are received.

4PROGRAMMABLE FUNCTIONS

DDDTMF TRANSMISSION

This function allows you to send a pre-programmed DTMF code to

control a repeater, open another transceiver’s squelch, etc.

Manual transmission:

Push the desired digit keys in sequence while pushing [PTT].

• Pushing [PTT] may not be necessary depending on programming.

Automatic pre-programmed transmission:

qPush the [DTMF Autodial] switch to select DTMF autodial mode,

then push [CH Up] or [CH Down] to select the desired channel.

wPush the [DTMF Autodial] switch to send a DTMF code.

DD DTMF RE-DIAL FUNCTION

This function allows you to transmit the last-used DTMF code at the

push of a key.

Push the [Re-dial] switch momentarily to activate the function.

• The previously transmitted DTMF code is automatically transmitted.

• If no code has been transmitted since turning the power ON, this func-

tion does not activate.

DDEMERGENCY FUNCTION

The emergency function allows you to send your ID quickly and

easily to your Base Station, etc. in case of emergency.

Push and hold the [Emergency Single/Repeat] switch for 1 sec. to

activate the emergency function.

• The transceiver selects a pre-programmed channel, then sends an

emergency signal to your Base Station.

• The pre-programmed channel remains selected until a control signal is

received from the Base Station, or power is turned OFF.

• The emergency call is repeatedly transmitted at pre-programmed in-

tervals.

PROGRAMMABLE FUNCTIONS

DDDISPLAY LIGHTING

The function display has 3 backlight conditions.

ON : Backlight turns ON continuously.

OFF : No backlight is available.

AUTO : When any key, except [PTT], is pushed, the backlight

turns ON for 5 sec. automatically.

DDSmarTrunk IITM functions

This transceiver provides SmarTrunk IITM functions.

(Optional UT-105

SmarTrunk IITM Logic Board

is required.)

The optional UT-105 allows communication over conventional

channels or SmarTrunk IITM channels. Select a channel bank for

SmarTrunk IITM before trunking operation.

To toggle SmarTrunk IITM channels and conventional channels, push

the [Bank] switch one or more times.

• Scanning starts when a channel bank for SmarTrunk IITM is selected.

• Contact your dealer for channel bank details.

(See p. 19 for more detailed operation.)

5CONVENTIONAL OPERATION

‘‘Receiving and transmitting

NOTE: Transmitting without an antenna may damage the trans-

ceiver. See p. 1 for antenna attachment.

Turn power ON as described on p. 3.

Receiving:

qPush [CH Up]/[CH Down], or rotate the [SEL] to select a chan-

nel.

wListen for a transmission and adjust [VOL] to a comfortable lis-

tening level.

• When no transmission is heard, push and hold monitor while ad-

justing [VOL] (your transceiver may not be programmed with the

monitor function).

The transceiver is now set to receive desired calls on the selected

channel.

Transmitting:

Wait for the channel to become clear to avoid interference.

eWhile pushing and holding [PTT], speak into the microphone at a

normal voice level.

• When a tone signalling system is used, the call procedure de-

scribed at right may be necessary.

rRelease [PTT] to return to receive.

IMPORTANT: To maximize the readability of your transmitted sig-

nal, pause a few seconds. after pushing [PTT], hold

the microphone 2 to 4 in. (5 to 10 cm) from your

mouth and speak at a normal voice level.

CONVENTIONAL OPERATION

‘‘Call procedure

When your system employs tone signalling (excluding CTCSS and

DTCS), the call procedure may be necessary prior to voice trans-

mission. The tone signalling employed may be a selective calling

system which allows you to call speciﬁc station(s) only and prevent

unwanted stations from contacting you.

qSelect the desired Tx code channel or 5-tone code according to

your System Operator’s instructions.

• This may not be necessary depending on programming.

• Refer to the next page for selection.

wPush the call switch (assigned to one of the dealer programma-

ble switches: [P0], [P1], [P2], [P3], [F2] and [F3]).

eAfter transmitting a 5-tone code, the remainder of your commu-

nication can be carried out in the normal fashion.

Selective calling Non-selective calling

5CONVENTIONAL OPERATION

‘‘Tx code channel selection

Your radio may be programmed for Tx code channel selection. In

this case, you can choose a Tx code channel to be transmitted

when using the call function (p. 17).

Push the Tx code channel switch (assigned to one of the dealer-

programmable switches) to activate the function, then enter digits

via the keypad to select the desired Tx code channel.

• The selected code channel (containing a pre-programmed 5-tone

code) is transmitted when using the call function.

‘‘Manual 5-tone codes

Depending on programming, you may be able to send 5-tone codes

manually.

Push the Tx code switch to activate the function, then enter the de-

sired transmit code (up to 7 digits) using the keypad.

• Activate the call function to transmit the 5-tone code.

• Blinking indicates keypad entry is acceptable.

‘‘Transmitting notes

DDTIME-OUT TIMER

After continuous transmission for a pre-programmed period, the

time-out timer is activated, causing the transceiver to stop trans-

mitting and automatically select receive.

DDPENALTY TIMER

Once the time-out timer is activated, transmission is further in-

hibited for a period determined by the penalty timer.

SmarTrunk IITM OPERATION

‘‘Basic operation

These features are enabled by your Dealer or System operator and

may not be available in your system. Contact your Dealer for details.

Push the [Bank] switch one or more times to select a channel bank

for conventional channels or SmarTrunk II™ channels.

• Scanning starts when a channel bank for SmarTrunk IITM is selected.

DDPTT dispatch operation*1

qPush [PTT] once (without dialling) to initiate a dispatch call.

wBegin talking after you hear three beeps (one short, high-

pitched, two very-short, low-pitched).

eReceiving a dispatch call is indicated by the same three-beep

sequence.

• It is not necessary to push [M] to answer a dispatch call.

DDSystem busy indication

If all channels are busy, three low beeps sound after you initiate

a call. Try the call again later.

DDReceiving a subscriber-to-subscriber call*1

When you hear ringing, push [M] to answer.

• For a group call, you hear a short ring followed by two short beeps.

You do not have to answer a group call to hear it over the air.

DDReceiving a landline-to-subscriber call*1

When you hear ringing, push [M] to answer.

• For a group call, you hear a short ring followed by two short beeps.

You do not have to answer a group call to hear it over the air.

DDTerminating a call*1

After completing a call, push [#] to disconnect (hang up).

IMPORTANT: If one person in the conversation terminates a call,

all participants will be cut off.

6SmarTrunk IITM OPERATION

DDLast number redial*1

Push [M], [M] to automatically redial the last number called.

• A high-pitched beep indicates that the number is accepted.

DDTurbo SpeeDial

To automatically dial a commonly used number with one push:

• Push one of the turbo SpeeDial keys.

DDProgramming memory speed dial

qPush and hold [M] until you hear a high-pitched beep.

wEnter the memory location (0–9, A, B, C, D), the telephone or

subscriber number, then [1], [M] (or [3], [M] if for another sys-

tem subscriber).

• A high-pitched beep indicates successful programming.

• Memories [A]–[D] are used for the Turbo SpeeDial.

NOTE: This function is available for the IC-F30GT/IC-F40GT

only.

DDMemory speed-dialling*2

To automatically dial a commonly used number from memory:

• Push [M] followed by the memory location (0–9).

DDClear channel alerting*1

If all channels are busy, the transceiver automatically begins

searching for an open channel and beeps every ten seconds.

When two short beeps (low-pitched, then high-pitched) are

heard, a channel is available. Push [M], [M] immediately to redial

the last number.

DDEmergency call*2

Push [0], [M] to initiate an emergency call.

• Contact your Dealer for details.

SmarTrunk IITM OPERATION

DDPlacing a telephone call*2

Enter the phone number followed by [1], [M].

• A high-pitched beep indicates that the number is accepted.

• When the called party answers, push the [PTT] switch to talk, and

release it to listen.

DDCalling another local system subscriber*2

Enter the subscriber number followed by [3], [M].

• A high-pitched beep indicates that the number is accepted.

• You hear ringing, then two short beeps when the subscriber an-

swers.

• If the other subscriber is on another call or out of range, you hear a

fast busy signal and the call terminates automatically.

*1: This function is available for the IC-F30GS/IC-F40GS when the

[F2]/[F3] keys are assigned the [M]/[ # ] key functions.

*2: This function is available for the IC-F30GT/IC-F40GT only.

Use the Turbo SpeeDial function instead.

For additional operating instructions, contact your Dealer or

System Operator.

7OTHER FUNCTIONS

‘‘DTMF PAGER/CODE SQUELCH

DDDTMF pager

This function uses DTMF tones for calling and can be used as a

“common pager” to inform you that one of your group has called

even if the operator is temporarily away from the transceiver.

• When the connection code is received, a beep sounds, then “ ”

flashes and shows the called stations code number.

• Called stations code number are memorized automatically, and are

easy to re-call with “ID-MR select function”.

DDCode squelch

This conveniently eliminates unwanted audio and is useful in

group activities or security related activities where unwanted out-

put can be a problem. The function is similar to a CTCSS tone

squelch.

In order to use the above functions, cloning is necessary via a

PC using the optional CS-F30G

CLONING SOFTWARE

. Using this

software, the transceiver’s model, individual RX Code CH, TX

Code CH, Special Tone Link2 (must be ‘E’) in 5Tone screen,

5Tone Signaling Form in Memory-CH screen, Log, RX C-No,

Key&Display, Common Auto Reset Timer B, and other settings

related to operation can be set. Refer to the HELP ﬁle that comes

with the CS-F30G

CLONING SOFTWARE

for available settings.

OPTIONAL UNIT INSTALLATION

You can install two of the following optional units in the transceiver.

UT-105

SmarTrunk II

Logic Board

, UT-109/UT-110

VOICE SCRAMBLER

UNIT

,UT-111

TRUNKING BOARD

,UT-113

MAN DOWN UNIT

‘‘Installation

qUnscrew nut a, and remove the knobs.

wUnscrew screw b, 2 screws cthen remove multi-connector

cover and rear panel.

eUnscrew 2 screws d, then remove multi-connector.

rUnscrew 2 screws ethen separate the chassis from the front

panel in the direction of the arrow.

Be careful!: A ﬂat cable is connected between the MAIN unit on the

chassis and front panel.

Install the desired optional unit. Insert tightly to avoid bad contact.

NOTE: When installing

UT-105 or UT-111, the

unit MUST BE plugged

into SLOT 1. Otherwise

the unit will not working

correctly. (Other optional

units can be plugged into

either slot.)

Program the necessary information with the cloning software before

operation. Please ask your dealer or system operator for details.

Slot 1

Slot 2

CLONING

‘‘Cloning

Cloning allows you to quickly and easily transfer the programmed

contents or data from PC to a transceiver using the optional CS-

F30G

CLONING SOFTWARE

DDPC-to-transceiver cloning

Please refer to the HELP ﬁle that comes with the CS-F30G

CLONING

SOFTWARE

CAUTION: Imprudent cloning operation causes a cloning error.

In such a case, memory contents may be lost. Cloning must

then be repeated.

OPTIONS

DDBATTERY PACKS

• BP-208

BATTERY CASE

Allows a set of Alkaline batteries to operate the handheld when

charging a rechargeable battery or in emergencies, etc. 6 AA (R6)

alkaline cells are required.

• BP-209

Ni-Cd

BATTERY PACK

7.2 V/1100 mAh Ni-Cd battery pack, allows more than 7 hours op-

eration.

• BP-210

Ni-MH

BATTERY PACK

7.2 V/1650 mAh Ni-MH battery pack, allows approx. 11 hours op-

eration.

DDCHARGER

• BC-137

BATTERY CHARGER

For regular charging of battery packs. An AC adapter is addition-

ally required. Charging time: 15 hrs.

• BC-119

DESKTOP CHARGER

+ AD-94 (#02)

CHARGER ADAPTOR

For rapid charging of battery packs. An AC adapter is supplied

with the charger. Charging time: 1.5 to 2 hrs.

• BC-121

MULTI

CHARGER

+ AD-94 (#02)

CHARGER ADAPTOR

(6 pcs.)

For rapid charging of up to 6 battery packs (six AD-94’s are re-

quired) simultaneously. An AC adapter may be supplied depend-

ing on version. Charging time: 1.5 to 2 hrs.

DDINTERNAL UNITS

• UT-105

SmarTrunk II

Logic Board

Provides SmarTrunk IITM capabilities.

• UT-109 (#02)/UT-110 (#02)

SCRAMBLER UNITS

Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler

unit provides higher communication security.

• UT-111

TRUNKING BOARD

Provides LTR®trunking capabilities.

• UT-113

MAN DOWN UNIT

Provides a measure of safety when working in a hazardous envi-

ronment, etc.

10OPTION

DDOTHER OPTIONS

• AD-52

EARPHONE JACK ADAPTER

Allows you to connect an earphone, 2-conductor 3.5 (d) mm (1⁄8″).

• EM-80/EM-89

SPEAKER

MICROPHONES

Combination speaker-microphone that provides convenient oper-

ation while hanging the transceiver from your belt.

• MB-68

BELT CLIP

Same as that supplied with the transceiver.

• MB-74

BELT CLIP

Exclusive alligator-type belt clip.

SmarTrunk II is a trademark of the SmarTrunk System Corporation. LTR is a reg-

istered trademark of EFJohnson Radio Systems.

MEMO

6-9-16 Kamihigashi, Hirano-ku, Osaka 547-0002 Japan

A-5668H-1EX

Printed in Japan

ICOM orporated IC-F30G Handheld Transmitter held to face User Manual IC F30G series

ICOM Incorporated Handheld Transmitter held to face IC F30G series

Contents

Manual

Navigation menu

Namespaces

Views

Navigation