User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2853654 |
| Application ID | Uxz4WxWxedguWmncNwE+Hg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 68.76kB (859516 bits) |
| Date Submitted | 2015-12-23 00:00:00 |
| Date Available | 2015-12-23 00:00:00 |
| Creation Date | 2015-12-16 20:30:36 |
| Producing Software | Acrobat Distiller 11.0 (Windows) |
| Document Lastmod | 2015-12-16 20:30:36 |
| Document Title | untitled |
UserManual ViVOpay KioskII 631-0071-00 Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page1of19 Copyright© 2014, International Technologiesand Systems Corporation.All rights reserved. ID TECH 10721 Walker Street Cypress CA90630 USA This document, as well as the hardwareand software it describes, is furnished under licenseand may only be used in accordance with the terms of such license. The content of this paper is furnished for informationaluse, subject to changewithout notice, and not to be construed as a commitment by ID TECH. ID TECH assumes no responsibility or liability for any errorsor inaccuracies that may appear in this document. Except as permitted by such license, nopartof this publication may be reproduced or transmitted byelectronic, mechanical, recorded, or any other method, or translated into another language or language form without the express written consent of ID TECH. ID TECH is a registered trademark of International Technologies and Systems Corporation. ViVOpay and Value through Innovation are trademarks ofInternational Technologies andSystems Corporation.Other trademarks are the property of the respective owner. Warranty Disclaimer: Theservices andhardware areprovided "asis" and "as-available," and the use of theseservices andhardware areat theuser’sown risk. ID TECH does notmake, and hereby disclaims, any andall other express or implied warranties,including, butnot limited to warranties ofmerchantability,title, fitness fora particular purpose, and any warranties arising from any course of dealing,usage, or trade practice. ID TECH does not warrant that the services or hardware will be uninterrupted, error-free, orcompletely secure. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page2of19 FCC Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide Reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed And used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try and correct the interference by one ormoreof the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes ormodifications to the ViVOpay Kiosk II not expressly approved by ID TECH could void the user’s authority to operate the ViVOpay Kiosk II. ICComplianceWarning Operation issubject to twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CautionsandWarnings 根據 NCC 低功率電波輻射性電機管理辦法規定: 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page3of19 Table of Contents Overview..............................................................................................................5 Features............................................................................................................5 ValidCard Types...............................................................................................5 Kiosk II Specifications.......................................................................................6 ViVOpayKioskIIInstallation.............................................................................7 PartList.............................................................................................................7 Mounting the ViVOpay KioskIIExternal Antenna.............................................8 Flush- Mounting the Square BezelAntenna................................................10 Mounting the ViVOpay KioskIIController.......................................................10 MountingtheViVOpayKioskII ControllerUsingScrews.............................10 MountingtheViVOpayKioskIIControllerUsingMountingTape.................11 AttachingtheCablesfromtheAntennatothe Controller................................11 Connectingto Power.......................................................................................12 Connecting to the Data Port............................................................................13 UsingtheViVOpayKioskIIto Make a Purchase.............................................14 PresentingCards,Fobs,orNFCPhones ....................................................14 Making a Purchase......................................................................................14 InstallationPoints.............................................................................................14 RFInterference..................................................................................................15 Troubleshooting................................................................................................16 Firmware Upgrade............................................................................................17 Serial Firmware Download Process................................................................17 Preparation..................................................................................................17 Load the ViVOpay KioskFirmware..................................................................17 USB FirmwareDownload................................................................................18 Symbols explanations.......................................................................................19 Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page4of19 Overview The ViVOpayKiosk II is a compactstand-alone contactless readerdesigned to support contactless transactions based on ISO 14443Type A/Type B/MiFare compatible cards, fobs, and tags aswell as NFC phones.The ViVOpay Kiosk II is comprised of a compact controller module and an antenna module packaged individually. This two-part design allows the controller module to be installedwithin thecabinetry of a kiosk and the antenna installed on an exterior surface witha separation of up to 1 meter. The antenna is availablewith a square or angled bezel. The ViVOpayKiosk II supportsUSB andserialRS232host communication usingthe protocol defined in theGlobal Reader Serial InterfaceDevelopers Guide. The ViVOpay Kiosk II is designed to support a wide input power range. Both dataand powercan be supplied via asinglecable to reducing the effort and complexity of installation. Features Supports ISO14443 TypeA, Type B, MiFareand NFC basedcontactless transactions 32-bit Microcontroller withample memory capable of supporting future application upgrades Crypto data processing forcontactless EMV cards RS232(9600,19200, 38, 400, 57, 600,115, 200 baud) host interface RS232 or USB data communications Small antenna flush-mounted on external cabinetry with square or angled bezel Internal mounted controller board with1meter controller/antenna separation Valid CardTypes ViVOpay Kiosk II supports the followingcontactless payment applications in thelatest release of firmware: ISO 14443 PayPass M/Stripe PayPass M/Chip PayPass MXI VisaWave 1 and 2 VisaPay/Wave MSD and qVSDC JCBJ/Speedy JCB Mobile/QuicPay American Express- ExpressPay Discover Zip MiFare ePurse Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page5of19 KioskII Specifications Hardware MTBF 500,000 hrsbased on TelcordiaTechnologies SR-332 modeled at 40°C. 13.56 MHz +/- 0.01% ISO 14443-2Type A Rise/Fall Time: 2-3 µsec.Rise, <1 µsec fall ISO 14443-2Type B Rise/Fall Time: <2 µsec. each; 8%-14%ASK 847.5 KHz ISO 14443-2Type A: Modified Manchester ISO 14443-2Type B: NRZ-l, BPSK 4-6 cm (1.5 to 2.3 inches) Transmitter Frequency TransmitterModulation Receiver Subcarrier Frequency Receiver Subcarrier Data Typical ReadRange Physical Controller Height Width Depth 105 mm (4.13 inches) 76.2 mm (3.00 inches) 22.5 mm (0.88 inches) Height Width Depth 75 mm (2.95 inches) 60 mm (2.36 inches) 16.8 mm (0.66 inches) Height Width Depth 96.2 mm (3.787 inches) 82.3 mm (3.24 inches) 16.8 mm (0.66 inches) Square BezelAntenna Angle Bezel Antenna Environmental Operating Temperature Storage Temperature Operating Humidity Electrical Reader Input Voltage -25° to 70° C(-13° to 158° F) -40° to 85° C(-40° to 185° F) 10% to 90% non-condensing +7.5v to 36 VDC (by AC to DC adapter) Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page6of18 ViVOpay Kiosk II Installation Thissection provides information on how to install the ViVOpay Kiosk II on a kiosk. PartList Verify that you have the following hardwarefor the installation of the ViVOpay Kiosk II: ViVOpay Kiosk II Controller ViVOpay Kiosk II Antenna(either square or angle bezel) Antenna LED power and data cable ViVOpay Kiosk II to ECR/POS cable(customer supplied). This USB or serial cable varies based on thehost to be used. Drill Template for the antenna (630-1046-00) Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page7of18 MountingtheViVOpayKioskII ExternalAntenna Use the following instructions to mount the antenna on the exteriorof the kiosk: Note: Verify the orientationof the ViVOpay Kiosk II Antenna beforemarking anddrilling the holes. The two larger holesshould be located towards the top ofthe mounting location to ensure that the ViVOpay KioskII Antennais oriented correctly with the LEDs at the top. 1. Using the Drill Template for the antenna(630-1046-00), locate and mark the four 4.4mm (0.173 inch) mounting holes. 2. Using the Drill Template, locate and mark the two 14.0 mm (0.551 inches) across holes (used for connectingthe antennapower and the LED power and datacable to the ViVOpay Kiosk II). 3. Drill the four 4.4 mm (0.173) mounting holes using a number 17 drill bit. 4. Drill the two 14.0 mm (0.551 inch) holesusing a 35/64 drill bit. 5. Remove thenuts from thefour mountingscrews. 6. Route the end of the cable(220-2457-00) with the RJ45 connectorthrough the left 14.0 mm (0.551 inch) hole in to the kiosk. Make sure that the front of the antenna will be properly oriented(not upside down)on the kiosk before inserting the fourscrews into the mounting holes. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page8of19 7. Align the four screwswith the mounting holes and attach the ViVOpay Kiosk II to the outside surface. Make sure that the cable is not pinched or binding. 8. Use the fournuts to secure the ViVOpayKiosk II to the outside surface of thekiosk. Makesure to tighten the nuts securely sothat the ViVOpay Kiosk II does not move on the outside surface of the kiosk. If you are installing the Angle Bezel Antenna, tighten the nuts to 5-7in/lbs. for a good weather seal. 9. Attach the end of the cablewith the SMB connector through the right 14.0 mm (0.551 inch) hold and attach it to the socketonthe back of the ViVOpay Kiosk II antenna. The SMB connector pushes on the socket of the antenna. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page9of19 10.Attach the RJ45 connectorcoming fromthe ViVOpay Kiosk II Antenna to the RJ45 receptacle onthe 220-2457-00cable. Flush- Mounting the Square Bezel Antenna The RF fieldof the antenna is sensitiveto the proximity of metal.Ifyou are flushmounting theantenna in a metal surfaceor bezel, you have three options: Mount with the RF emittingsurface of the antenna at least 1 cm forward of any metal. Mount with the RF emittingsurface of the antenna at least 1 cm behind any metal. This will reduce theeffective range of the antenna. Mount flushwith the metal but allow aminimum of 1cm spacing between the antenna and the metal. In all cases, test the antenna mounting before engaging in a full scale installation. MountingtheViVOpayKioskII Controller Note: The ViVOpay Kiosk II Controller must be mounted within 1meter of the antenna. If the antenna is mounted on a surface that opens (such asa door), make sure the controller and antenna areclose enough that there is no tension on the cable when the enclosure is open. If it is acceptable, the installer can drill four holes for mounting thecontroller if screw heads can appear on the outside of thekiosk.In thiscase, it wouldbe advisableto use security screws to preventtampering with the screws. If drilling additional holes on the outside ofthe kiosk surface is notacceptable, the installer can use double-sided tape to mountthe controller to any clean surface. Mounting the ViVOpayKiosk II Controller Using Screws 1. Position theViVOpay Kiosk II controller on the interior of the kiosk making sure that there issufficient room for the antenna mountingsurface to be fully opened. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page10of19 2. Locate the four 4.4 mm (0.173 inch) mounting holesby holding the ViVOpay Kiosk II Controller in position andmark the holes. The following diagramshows the spacing on the holes to be drilled for mounting the ViVOpay Kiosk II Controller. 3. Drill the four 4.4 mm (0.173 inch) mounting holes using a number 17 drill bit. 4. Use fourscrews and nuts to mount theViVOpay Kiosk II Controller to the kiosk surface. (Mounting screws are not provided and must be supplied bythe installer.) 5. Tighten the nuts to hold the ViVOpay Kiosk II Controller in positionso that it does not move. Mounting the ViVOpayKiosk II Controller Using Mounting Tape 1. Position theViVOpay Kiosk II Controller on the interior of the kiosk making sure that there issufficient room for the antenna mountingsurface to be fully opened. 2. Attach double-sided tape tothe mountingsurface. 3. Position theViVOpay Kiosk II Controller over the mounting tape and gently apply pressure to hold the controller in position. AttachingtheCablesfromtheAntennatotheController 1. Attach the SMB end of the cable (220-2457-00) from the antenna to the ViVOpay Kiosk II Controller. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page11of19 2. Attach the other end of the cable (220-2457-00) from the antenna to the ViVOpay Kiosk II Controller. Note: Verify that the polarizing plug on the end of thedata cable isfacing towards the top of the ViVOpay Kiosk II Controller (away from the mounting plate) before inserting the cable.If the cable is installed incorrectly (upside-down), it willapply the wrong polarity to the LEDs and damage them. Connecting to Power The Kiosk II can be powered through the serial communications port or the two-socket power connector. If you are using USB data communications, you must power the Kiosk II through the two-socket power connector. By using AC to DC adapter to Connect to the white two-socket Molex connector (mating connector Molex P/N 0039012020with 5556-series crimps) or to pins 1 and 2 of the RS232 connector (see next section). (P.S Please don’t use DC power source for our units, and this product do not supply the DC Jack Cable). Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page12of19 Connecting to the Data Port The Kiosk II has two data connections options: USB through the USB connector and RS232 through the 14-pin Molex connector. The USB port uses a standard USB connector and pin outs. TheRS232 port has the following pin outs. Pin 11 13 Description Power ground Power ground No connection Reserved Signal ground RS232 Tx ISP Input Pin 10 12 14 Description +7.5v to 36VDC (By using AC to DC adapter) +7.5v to 36VDC (By using AC to DC adapter) Reserved Reserved Signal ground RS232Rx Reserved To build your ownRS232cable, use Molex female connector part number 0511101451 with 50394-series crimps (see www.molex.comfor more information). Pin 1 is indicated by a triangle (diagram issocket-side viewof the female connector). Ifyou are powering the Kiosk II from this connector,wire the two powerpins (pins 2 and 4) together and the two power ground pins together (pins 1 and 3). Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page13of19 UsingtheViVOpayKioskIItoMakeaPurchase Presenting Cards, Fobs, or NFC Phones Your new ViVOpay Kiosk II allows for credit/debit card purchasesusing the new contactless technology. Present the card/fob/phone in close proximity tothe front portion ofthe antennamodule. Present the card/fob/phone so that maximum surfacearea is parallel to the antenna module as shown below. The antenna should beep and all four green LEDs should illuminate briefly to indicate a successful test. This tests theantenna’s ability to read the RFIDtest card. If unsuccessful, therewill be no reaction from the reader. If you use a test card andthe ViVOpay reader is attached to the ViVOpay Kiosk II Controller, a dummytransactioncan be tested. The transaction will not be authorized and willcome backwith a response,but will at least test for end-to-end connectivity. Making aPurchase After the transaction has been enteredonthe kiosk control panel, the customer should present their card/fob/phone in close proximity so that maximum surfacearea is parallel to the antenna. A single beep and all fourLEDs briefly flashing indicates the card/fob/phone has been readcorrectly. Installation Points The ViVOpayKiosk II is designed to bemounted on ametal surface and in close proximity to any internal motors and electrical devices that may beoperating inside the kiosk. However, the ViVOpay Kiosk IIis susceptible to RF andelectromagnetic interference. It is importantthat the unit not be mounted near(within3 or 4 feet) large electric motors, computerUPS systems,microwave transmitters, anti-theft devices, radio transmitters, communications equipment and so on. Close proximity of metal tothe RF-emitting end of theantenna can greatly reduce the range of the antenna. See the precautions describedin FlushMounting the Kiosk IIAntenna. Tie all cablesneatly with nylon cable-tiesand route them so that they are inaccessibleand invisible to customers.Label thecable ends, host,ViVOpay, and power, to simplify connection testing or component replacement. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page14of19 Test the ViVOpay Kiosk II installation using a test card to performan end-to-end transaction (the same as an actual purchase on theKiosk). Thekiosk control panel should display “Requesting Authorization”. Even if the transaction is declined (as it should bewith a test card),it will proveconnectivity all the way through the system. If possible the store manager or some other responsibleparty should test each cardto ensurecontinued operationand functionality. If the kiosk is rebooted on a regular basis (such as every night) it is importantto test the contactless reader as soonas possible afterwards to ensure continuedcommunication to the kiosk. Refer to the troubleshooting section of thismanual before contacting your distributor with support questions. RF Interference Q. WhydoIneed to knowaboutRF interference? A. Contactless payments use radio frequency technology to sendcard data to a contactless terminal reader. Q. HowcanRF interference affect contactless payments? A. RF interference can cause data errors. If RF interference is present, contactless payment devices may operation intermittently or inconsistently. Q. Where does RF interference come from? A. Radio frequency interference (RFI) can originate from a wide number of sources at the point-of-sale (POS). Some examples of sources of RF energy andRF interference include: AM/FM radioand TV transmitters 2-way radios,pagers Mobile telephones Power lines, transformers Medical equipment Microwaves Electromechanicalswitches Q. What should I do if I suspect RF interference exists in myenvironment? A. Begin by inspecting your environmentfor possible sources ofRF interference. Q. Do equipment manufacturers testtheir devices for RF interference? A. Electronicequipment istested forRFI sensitivity by the manufacturers. Thesetests are performed in a controlled laboratory environmentand will oftennot replicate the types of devices that would be encountered inyour point-of- sale(POS)environment. Q. WhatRF levelswill impactRF operations? A. Factors that can causeRF interference vary case-by-case. There are noset rules defining asingle RF level that will cause RFI. RFI depends on the sensitivity of the equipment under consideration, or how low an interpreting signal can be in the presence of the equipment and cause problems. Equipment can be particularly sensitive to very low signal levels of one frequency and yet be quite immune to highsignal levels of another frequency-so frequency is an important factor. Some electronic system components areinternally shielded and have a very high immunity to interference; but generally, most equipment has not been so engineered. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page15of19 Troubleshooting The ViVOpayKiosk II readers arereliable and easy to troubleshoot. The components that may require troubleshooting include thepowermodule (if applicable), the reader, and the serial cable. Symptom Possible Cause Remedy General Issues Reader does not Reader not powered on or Check cableconnections. appear to bepowered incorrect voltage. Verify that power is on and on (no LEDs lit). Improper useof internal correct voltage and currentare power supplyprovided by present. the kiosk. Makesure that the correct pins are utilized. Makesure that the power provided is within the specified range of the Kiosk II reader. Makesure that the correct polarity is observed. For more information, refer to the Input Voltageunder the Electrical specificationsection. Replace the ViVOpay Kiosk II. Reading Cards/Fobs/Phones LEDs do not light and Card/fob/phone not beeper is not audible properly presented. when card/fob/phone RF interference. is presented. Unsupported card used. Wrong firmware (contact your local support representative). Some card/fobs/phones read, but not all. Possible bad card/fob/phone. Unsupported card used. Wrong firmware (contact your local support representative). Present card/fob/phone closer to the antenna, and ensure it is parallel to the face of the reader. Verify that the card/fob/phone is valid/current. Verify that metal is not interfering with the antenna. Testwith “Contactless Test Card” part number 241-0015-03 RevA. Verify that the Phone Wallet is enabled for payments. Try a differentcard/fob/phone. Check to seeif card/fob/phone is damaged. Verify that phone cover is correctly attached to phone (Nokia 3220). Verifythat correct firmwareis loaded on reader (local support representative only). Power cableplug is fully inserted. Replace the ViVOpay Kiosk II. Check to seeif card/fob/phone is damaged. Verify that phone cover is correctly attached to phone. Verifythat correct firmwareis loaded on reader (local support representative only). Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page16of19 Symptom Possible Cause Communication to Kiosk No data is received, or Faulty or incorrect cable data is garbled. connections. Remedy Check that the cable connection is secure and in the correct port on the kiosk. If you are unable to resolvethe problem, contact your localsupport representative. Firmware Upgrade The Kiosk II can be upgraded using either the serial or USB interfaces. SerialFirmwareDownloadProcess The ViVOpayKiosk II canonly be upgraded when it is placed in upgrade mode by drawing down the ISP signal on the externalconnector. Using thecable and dongle mentioned above accomplishes this by connecting theISP pin tothe RS232signal ground. If the ISP is grounded when theViVOpay Kiosk II powerson, it enters download mode. Otherwise it will operate normally, emitting abeep and flashing LEDs when powered on. If you want to build your own downloadcable,the pinouts to the external connector are given in Connecting to theData Port. After you have entered download mode, you must erase the current firmware and install the new firmware. Preparation To install thenew firmwareyou will need: PC with available serial orUSB port ViVOpay Kiosk II with a serial orUSB data cable attached For serial downloads: 220-1275-00 Download Dongle (DB-9 serialto RJ45) Philips LPC2000 Flash Utility software Firmware file for the desired firmware (contact ViVOpaysupport@idtechproducts.com) Power supplyfor the ViVOpay reader (7.5- 36 VDC; 3 Watts output). LoadtheViVOpayKioskFirmware 1. Install the LPC2000 flash utility program on the PC. 2. Copy the ViVOpay Kiosk II firmware on the PC. 3. Connect the download dongle (220-1275-00) to thePC COM portand plug in the 220-2374-00cable from ViVOpay Kiosk II tothe dongle. 4. Connect the power to the ViVOpay reader. Thereshould be no beep, and no LED activity. 5. Launch the Philips LPC2000 utility. If the Philips utility fails to identify any reader attached, please follow thetroubleshooting steps given in Troubleshooting. 6. Set the Device to LPC 2138. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page17of19 7. The COM port is normally set to1 but this depends upon your PCDevice Manager setup. Youcan select the COM port to which thecable is connected by navigating to the WindowsDevice Manager (Start ->Settings ->Control Panel->System >Hardware->Device Manager ->Ports) to verify theactual port number that is assigned to the serial port. PressENTERafter making the selection. 8. ClickRead Device ID, thePart ID: andBoot LoaderID: fields should be filled inif the reader is responding to the utility. Note: If the reader does NOT respond to the utility, reset the reader by unplugging and replugging the power connector andtry again. 9. ClickErase. This erases the old firmware on the reader. A message indicates a successful erase. 10.ClickBlank Check (with Entire Device selected) to confirm that the erase function worked properly. 11.In the Flash Programming box, click the “…” box to select the firmware file you want to load on the ViVOpay Kiosk II. 12.ClickUploadto Flash to load the firmware on the reader (the % completion bar shows the firmware loading progress). 13.Disconnect power and theserial dongle. 14.Connect power to the Kiosk II and connect the standard datacable. It will load the new firmwareapplication. USBFirmwareDownload The download process over the USB interface is performed with the bootloader commands presented in theSerial InterfaceDeveloper’s Guide. For a copy of the Serial Interface Developers Guide contact ID TECH or yourID TECH representative. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page18of19 Symbols explanations The symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end its life separately from your household waste. There are separated collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product. Copyright©2010-2014,InternationalTechnologies&SystemsCorp.Allrightsreserved. Page19of19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2015:12:16 20:30:36+08:00 Modify Date : 2015:12:16 20:30:36+08:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Producer : Acrobat Distiller 11.0 (Windows) Format : application/pdf Title : untitled Document ID : uuid:1e59300d-8fb8-4888-bfed-c381742a6524 Instance ID : uuid:5f4fd00d-3756-444d-aa49-a23a035c4dc8 Page Count : 19EXIF Metadata provided by EXIF.tools