ID Teck Co STARRF-TINY Proximity Reader ( RF-Tiny) User Manual 285773
ID-Teck Co Ltd Proximity Reader ( RF-Tiny) 285773
User Manual
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 1 -
OPERATING AND
INSTALLATION MANUAL
RF-Tiny
Proximity Reader
Revision : 02
Date : November 16, 2001
ID TECK Co. Ltd.
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 2 -
CONTENTS
1. Introduction page 3
2. Identifying supplied parts page 3
3. Specification page 3
4. Installation page 4
5. Wire Color Table of the Reader page 5
6. Wire Connection to Controller page 5
7. Operation page 6
8. FCC Registration Information page 7
9. Warranty and Service page 8
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 3 -
1. Introduction
The STAR RF-Tiny is an elegant looking and an attractive 4" read range proximity reader which
can be mounted to metal door frame(mullion) or any flat wall surface. The RF-Tiny use the
electronics module in epoxy potting that ensure you successful operation even in harsh
environments. Two color LED of green and red, inside Piezo buzzer sound will guarantee you an
accurate and reliable system operations.
2. Identifying supplied parts
Please unpack and check the contents of the box.
Reader Module RF-Tiny Bezel Instruction
(1 ea) (1 ea) (1 ea)
3. Specification
Read Range/Time Up to 4"(10cm) / 30ms
Input Voltage/Current DC 12V, Max. 150mA
Output Format 26 bit Wiegand, ABA Track II, RS232C
External Buzzer control Input Low Active, DC 0 ~ 12V, Max. 50 mA
External LED control Input Low Active, DC 0 ~ 12V, Max. 50 mA
LED/Buzzer 2 Color LED(Red and Green) / Piezo Buzzer
Color Dark Gray
Operating Environment -31 ~ 149(-35 ~ +65), 0~90% Humidity
Overall Size(WxHxD) 1.77"x3.35"x0.65"(45x85x16.5mm)
Weight 0.157lb(71.5g)
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 4 -
4. Installation
4-1. Mullion/Wall Mount
Drill two 3mm holes 2.72"(69mm) apart in vertical and drill one 1/2" hole for
the controller cable 1.36"(34.5mm) apart from the top hole.
4-2. Put controller cable into the center hole and install the controller module by using two
3-20 screws.
4-3. Put bezel into the controller module then push bezel until you hear the locking sound.
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 5 -
5. Wire Color Table of the Reader
POWER
Power(DC +5V~+12V) DC(+) Red wire
Power(DC Ground) DC(-)(GND) Black wire
INPUT
Buzzer control input BUZZER Blue wire
LED control input LED Yellow wire
OUTPUT(Wiegand Format)
Wiegand Data-0 Data-0 Green wire
Wiegand Data-1 Data-1 White wire
OUTPUT(ABA Track II Format)
ABA(Card Present) CP Orange wire
ABA(Clock) CLK White wire
ABA(DATA) Data Green wire
OUTPUT(RS232C Format)
RS232C(TX) TX White wire
6. Wire Connection to Controller
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 6 -
7. Operation
7-1. Apply power and you can see Red LED is on indicating the reader is in standby.
7-2. Present proximity card to the reader until you hear beep sound and the LED is
changing the color to Green simultaneously and the reader send RF card data to the
controller then LED changes the color to Red again for next reading.
7-3. LED Control;
To change the LED colors, you may connect LED Control Input(Yellow wire) to
power ground then the Green LED is on indicating the reader is in standby.
Present proximity card then the LED changes the color to Red simultaneously then
Green again for next reading.
7-4. Buzzer Control;
When the reader reads proximity card, only one beep sound generates in normal
operating mode but you can generate more beep sounds to distinguish whether the
access is granted or denied.
To generate more beeps, you may control the Buzzer Control Input(Blue wire) to power
ground then you can turn beeper on while you hold Buzzer Control Input to power ground.
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 7 -
8. FCC REGISTRATION INFORMATION
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not expressly approved by the
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant to Part 15
of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the radio or television
off and on, the user is encouraged to try to correct interference by one or more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
STAR RF-Tiny PROXIMITY READER
RF TINY-20011117 - 8 -
9. Warranty and Service
The following warranty and service information applies only to the United States of America and Republic of Korea.
For the information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed
below.
IN THE UNITED STATES
RF LOGICS Inc. Service Center
3026 Scott Blvd.,
SANTA CLARA, CA95054
Tel.: (408) 980-0001
Fax.: (408) 980-8060
E-mail: rflogics@rflogics.com
Web-site: www.rflogics.com
OUTSIDE OF THE UNITED STATES
ID TECK CO., LTD. Service Center
5F Ace Techno Tower Bldg.,
684-1 Deungchon-dong, Gangsuh-gu,
SEOUL 157-030, KOREA
Tel.: +82 (2) 659-0055
Fax.: +82 (2) 659-0086
E-mail: webmaster@idteck.com
Web-site: www.idteck.com
Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage,
include the following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to address
3. Ship-to address
4. Number and description of units shipped.
5. Name and telephone number of person to contact.
6. Reason for return and description of the problem.
NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made
directly to the carrier.