IDEMIA Identity and Security France MPHAC002A Control Access Terminal User Manual

SAFRAN Identity & Security Control Access Terminal

UserManual.wiki >

IDEMIA Identity and Security France >

MPHAC002A User Manual

User manual.pdf

MorphoAccess® SIGMA Extreme Series Installation Guide COPYRIGHT © 2017 Safran Identity & Security Osny, France 2017_2000024418 - Draft V0 January 2017 Identity & Security

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Warning 2 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Warning COPYRIGHT © 2017 Safran Identity & Security. All rights reserved. Reproduction in whole or in part in any form or medium without the express written permission of Safran Identity & Security is prohibited. The trademarks identified herein are the trademarks of registered trademarks of Safran Identity & Security, or other third party This legend is applicable to all pages of this document. Information in this document is subject to change without notice and do not represent a commitment on the part of Safran Identity & Security. This manual makes reference to names and products that are trademarks of their respective owners.

MorphoAccess® SIGMA Extreme Series - Installation Guide Revision History Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 3 Revision History The table below contains the history of changes made to the present document. Version Date Reference Description 01 January 2017 2017_2000024418 – Draft V0 Document creation - Draft

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Table of Content 4 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Table of Content Warning ........................................................................................................................................ 2 Revision History ............................................................................................................................ 3 Section 1 : Introduction ................................................................................................................ 9 MorphoAccess® SIGMA Extreme Series Terminal ................................................................... 10 Scope of the document ............................................................................................................ 11 Safety Instructions ................................................................................................................... 12 Wiring Recommendations ................................................................................................... 13 Regulatory, safety and Environmental notices ....................................................................... 14 European Union (CE) regulatory notices ............................................................................. 14 USA (FCC) regulatory notices ............................................................................................... 15 Canada (IC) regulatory notices ............................................................................................ 16 Others recommendations .................................................................................................... 16 Recommendations for terminal implementation .................................................................... 17 Section 2 : General Description .................................................................................................. 20 Box opening ............................................................................................................................. 21 Components of the initial package ......................................................................................... 22 Terminal's front view description ............................................................................................ 23 Terminal's rear view description ............................................................................................. 24 MorphoAccess® SIGMA Extreme Series Technical Characteristics ......................................... 25 Section 3 : Installation Procedure ............................................................................................... 27 Before proceeding to the installation ..................................................................................... 28 Installation .............................................................................................................................. 29 Required tools (not supplied)............................................................................................... 29 Equipment from the initial package to use ......................................................................... 29 Step by step procedure ........................................................................................................ 30 Section 4 : Electrical Interface .................................................................................................... 34 Wiring overview ...................................................................................................................... 35 Power Supply ........................................................................................................................... 36 External Power supply ......................................................................................................... 36 POE (Power Over Ethernet) ................................................................................................. 36 Output Relay ........................................................................................................................... 37 Nominal characteristics of relay .......................................................................................... 37

MorphoAccess® SIGMA Extreme Series - Installation Guide Table of Content Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 5 Example of connection for electrical door locks .................................................................. 37 Tamper Switch ......................................................................................................................... 38 Operating principle for the switch ....................................................................................... 38 Nominal characteristics of switch block .............................................................................. 38 Wiegand wiring ....................................................................................................................... 39 Wiegand input ..................................................................................................................... 39 Wiegand output ................................................................................................................... 40 The controller supports neither LED1 nor LED2 signals ....................................................... 40 The controller supports only LED1 signal ............................................................................ 40 The controller supports LED1 and LED2 signals .................................................................. 41 Serial port wiring ..................................................................................................................... 42 DataClock Input ................................................................................................................... 42 DataClock Output ................................................................................................................ 42 RS485 ................................................................................................................................... 43 RS422 ................................................................................................................................... 43 GPIO wiring ............................................................................................................................. 44 Single Door Access Control (SDAC) implementation ........................................................... 44 Ethernet connection ................................................................................................................ 45 Default Ethernet configuration ........................................................................................... 45 Recommendations for RJ45 wiring ...................................................................................... 45 External USB connection ......................................................................................................... 46 Wi-Fi™ dongle installation ...................................................................................................... 47 Micro SD connection ............................................................................................................... 48 Section 5 : User Interface ........................................................................................................... 49 Modes for controlling access rights ........................................................................................ 50 Introduction ......................................................................................................................... 50 Identification mode ............................................................................................................. 50 Authentication (verification) mode ..................................................................................... 50 Multi-factor mode ............................................................................................................... 51 Proxy mode .......................................................................................................................... 51 External database mode (also called polling mode) ........................................................... 51 Configuring the terminal ......................................................................................................... 53 MorphoAccess® 500 or J Series legacy mode ...................................................................... 53 MorphoAccess® SIGMA Extreme Series native mode .......................................................... 54 Anti-tamper / anti-pulling switches ........................................................................................ 55 Section 6 : Accessories, Software Licenses and PC Applications ................................................ 56

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Table of Content 6 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Compatible Accessories, Licenses and Software ..................................................................... 57 Compatible PC applications .................................................................................................... 58 Section 7 : Recommendations .................................................................................................... 59 Global warning .................................................................................................................... 60 General precautions ............................................................................................................ 60 Areas containing combustibles ............................................................................................ 60 Specific precautions for terminals equipped with a contactless smartcard reader ............ 60 Ethernet connection ............................................................................................................ 60 Date / Time synchronization ............................................................................................... 60 Cleaning precautions ........................................................................................................... 61 Legacy mode ........................................................................................................................ 61 Micro SD card ...................................................................................................................... 63 Lighting conditions for face detection ................................................................................. 63 Main principles ........................................................................................................................ 65 Most useful areas for biometric data...................................................................................... 66 Position of finger ..................................................................................................................... 67 Finger height ........................................................................................................................ 67 Finger angle ......................................................................................................................... 67 Finger inclination ................................................................................................................. 68 Finger rotation ..................................................................................................................... 68 Troubleshooting ...................................................................................................................... 69 How to get the latest versions of documents ......................................................................... 71 Documents concerning the MorphoAccess® terminal ............................................................ 72 Documents about installing the terminal ............................................................................ 72 Documents about administrating / using the terminal ....................................................... 72 Documents for the developer .............................................................................................. 72 Release note ........................................................................................................................ 73 Troubleshooting ...................................................................................................................... 75 The terminal IP address is unknown or it is not possible to connect to the terminal.......... 75 The sensor is switched off .................................................................................................... 75 The terminal returns erratic responses to Ping commands ................................................ 75 Technical Support and Hotline ................................................................................................ 76 North America ..................................................................................................................... 76 South America ..................................................................................................................... 76 South Africa ......................................................................................................................... 76 India: .................................................................................................................................... 76

MorphoAccess® SIGMA Extreme Series - Installation Guide Table of Content Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 7 Europe and rest of the world: .............................................................................................. 76 Web site ............................................................................................................................... 76 Annex 1 : Finger Placement Recommendations ...................................................................... 64 Annex 2 : Bibliography ............................................................................................................. 70 Annex 3 : Support .................................................................................................................... 74

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Table of Figures 8 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Table of Figures Figure 1: Implementation Recommendations ............................................................................. 18 Figure 2: Box Opening .................................................................................................................. 21 Figure 3: Box Content .................................................................................................................. 22 Figure 4: MorphoAccess® SIGMA Extreme Series terminal front view ....................................... 23 Figure 5: MorphoAccess® SIGMA Extreme Series terminal rear view ........................................ 24 Figure 6: Removing wall frame .................................................................................................... 28 Figure 7: Face camera viewing angle ........................................................................................... 30 Figure 8: Drilling template ........................................................................................................... 31 Figure 9: Wall plate fixing ............................................................................................................ 32 Figure 10: Cabling layout ............................................................................................................. 35 Figure 11: Power supply wiring ................................................................................................... 36 Figure 12: Output relay wiring ..................................................................................................... 37 Figure 13: Example of electric latch connection ......................................................................... 37 Figure 14: Tamper switch wiring ................................................................................................. 38 Figure 15: Wiegand input wiring ................................................................................................. 39 Figure 16: Wiegand output wiring ............................................................................................... 40 Figure 17: Serial port wiring – DataClock Input ........................................................................... 42 Figure 18: Serial port wiring – DataClock Output ........................................................................ 42 Figure 19: Serial port wiring – RS485 ........................................................................................... 43 Figure 20: Serial port wiring – RS422 ........................................................................................... 43 Figure 21: GPIO wiring ................................................................................................................. 44 Figure 22: SDAC wiring................................................................................................................. 44 Figure 23: RJ45 wiring .................................................................................................................. 45 Figure 24: External USB connection ............................................................................................ 46 Figure 25: Wi-Fi™ dongle installation .......................................................................................... 47

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 9 Section 1 : Introduction

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 1 :Introduction 10 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 MorphoAccess® SIGMA Extreme Series Terminal Congratulations for choosing a MorphoAccess® SIGMA Extreme Series Automatic Fingerprint Recognition Terminal. MorphoAccess® SIGMA Extreme Series provides an innovative and effective solution for access control applications using Fingerprint Verification or/and Identification. Among a range of alternative biometric technologies, the use of finger imaging has significant advantages: each finger constitutes an unalterable physical signature, developed before birth and preserved until death. Unlike DNA, a finger image is unique to each individual - even identical twins. MorphoAccess® SIGMA Extreme Series integrates Safran Identity & Security image processing and feature matching algorithms. This technology is based on lessons learned during 25 years of experience in the field of biometric identification and the creation of literally millions of individual fingerprint identification records. We believe you will find the MorphoAccess® SIGMA Extreme Series fast, accurate, easy to use and suitable for physical access control. The MorphoAccess® SIGMA Extreme Series offers the following advantages:  high quality optical sensor (IQS quality sensor) with false finger detection option,  supports multiple input/output interfaces used in the physical access control industry,  Local Area Network interface for easy interaction with other host systems ; LAN and WLAN possibilities (Wi-Fi™ as an option),  intuitive man machine interface with touch panel and display, that is easy to use in both setup and operational modes,  sturdy wall mounting with easy holding of product during cabling or maintenance,  ruggedezied design for harsh environment (IK09 and IP65). To ensure the most effective use of your MorphoAccess® SIGMA Extreme Series terminal, we recommend that you read this Installation Guide completely.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 11 Scope of the document This guide deals with the installation of MorphoAccess® SIGMA Extreme Series, which is made up of following list of products: MA SIGMA Extreme Series Marketing Name Biometrics Fake Finger Detection Contactless smartcard reader Water Resistant Regulatory Model Number (*) iCLASS® MIFARE® DESFire® NFC Prox® MA SIGMA Extreme iClass    MPH-AC002B MA SIGMA Extreme Multi    MPH-AC002B MA SIGMA Extreme Prox    MPH-AC002A MA SIGMA Extreme FFD iClass     MPH-AC002B MA SIGMA Extreme FFD Multi     MPH-AC002B MA SIGMA Extreme FFD Prox     MPH-AC002A (*) The Regulatory Model Number is the main product identifier in the regulatory documentation and test reports associated to the product NOTA : MA means MorphoAccess®

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 1 :Introduction 12 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Safety Instructions means Direct Current (DC) The installation of this product should be made by a qualified service Person and should comply with all local regulations. It is strongly recommended to use a class II power supply at 12V-24V and 1A. min (at 12V) in conformity with Safety Electrical Low Voltage (SELV). The power supply cable length should not exceed 10 meters. This system must be installed in accordance with the National Electrical Code (NFPA 70), and the local authority having jurisdiction. This product is intended to be installed with a power supply complying with IEC60950-1, in accordance with the NEC Class 2 requirements; or supplied by a listed IEC60950-1 external Power Unit marked Class 2, Limited Power source, or LPS and rated 12VDC, 1A minimum or 24VDC, 0.5A minimum. In case of building-to-building connection it is recommended to connect 0V to ground. Ground cable must be connected with the terminal block Power Ground. Note that all connections of the MorphoAccess® SIGMA Extreme Series terminal described hereafter are of SELV (Safety Electrical Low Voltage) type.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 13 V1 V2 L Wiring Recommendations Safran Identity & Security recommends using a gauge AWG20 for 12V power supply when POE supply is not used. The voltage specified is the one measured on the product block connector: 12V-24V (-15% / +10%) For information, this table shows the maximum drop voltage observed on the terminal MorphoAccess® SIGMA Extreme Series: Gauge AWG Diameter (mm) Maximum drop voltage @ 1m (V) Maximum drop voltage @ 5m (V) Maximum drop voltage @ 10m (V) 20 0.81 0.03 0.17 0.33 22 0.64 0.05 0.26 0.53 24 0.51 0.08 0.42 0.84 Drop voltage = loss of power due to wire resistance and its length: V2 = V1 – Drop voltage

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 1 :Introduction 14 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Regulatory, safety and Environmental notices European Union (CE) regulatory notices Declaration of Conformity Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:  Low Voltage Directive 2006/95/EC  EMC Directive 2004/108/EC  R&TTE Directive 1999/5/EC  Ecodesign Directive 2009/125/EC  RoHS Directive 2011/65/EU. Compliance with these directives is assessed using applicable European Harmonised Standards. MorphoAccess® SIGMA Extreme Series terminals are intended to be used for professional application only (buildings, airport...). This is an EMC Class A product according to EMC directive 2004/108/EC. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce magnetic emissions to prevent interference to the reception of radio and television broadcast. The full Declaration of Conformity is available on demand to your reseller. Please, provide him the product model name or its Regulatory Model Number (Model on the label). Products with wireless features (EMF) This product meets the provisions of the EU's Council recommendation 1999/519/EC on the limitation of the exposure of the general public to electromagnetic fields (0 Hz to 300 GHz).

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 15 USA (FCC) regulatory notices This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Responsible Party: Safran Identity & Security 11, boulevard Gallieni 92130 Issy-les-Moulineaux – France NOTA : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Shielded cables must be used with this unit to ensure compliance with category B FCC restrictions.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 1 :Introduction 16 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Canada (IC) regulatory notices WARNING TO USERS IN THE CANADA / ATTENTION POUR LES UTILISATEURS AU CANADA This device complies with Industry Canada license-exempt RSS standard(s), and with ICES 003 standard for version(s) without RFID reader. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Note : UL LLC has not verified this product for compliance in respect to Canadian standards. Others recommendations Potential safety conditions notice If you notice any of the following conditions (or if you have other safety concerns), do not use the product: crackling, hissing, or popping sound, or a strong odor or smoke coming from the product. It is normal for these conditions to appear when an internal electronic component fails in a safe and controlled manner. However, these conditions may also indicate a potential safety issue. Do not assume it is a safe failure. Turn off the product, disconnect it from its power source, and contact technical support for assistance. Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 17 Recommendations for terminal implementation Every installation is unique. Sometimes the issues are well defined and can be handled in a standard fashion; sometimes the issues are very specific and may not be immediately recognizable. Safran Identity & Security recommends following these steps for a successful installation:  Plan the installation - Choose the type of hardware required, decide if a network is required, and decide on the location and number of required terminals.  Unpack all items - Unpack all items and check against the packing list.  Install network hardware components - Install the cabling and components needed to run the system.  Install software - Install the software needed to set up the terminals.  Pre-configure device - Connect the terminals to the Ethernet, supply power to the terminals, and pre-configure the terminals.  Mount devices - Mount the terminals in their final locations  Power distribution and device hook up - Connect the terminals wiring via the back panel.  Power-up procedure - Check the power connections, and then start the system safely. First Boot Assistant screen is displayed, where you can perform fundamental configuration.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 1 :Introduction 18 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 To secure properly an access, Safran Identity & Security recommends installing the MorphoAccess® SIGMA Extreme Series terminal as a part of the typical Access Control environment, described in the figure below. Figure 1: Implementation Recommendations This environment comprises: The MorphoAccess® SIGMA Extreme Series terminal itself Its role is to perform one-to-many biometric identification or one-to-one biometric verification, i.e. to identify the individual who is presenting his finger on the terminal sensor by comparing his biometric data with the references previously stored in the terminal database (in the form of biometric templates) or to verify his identity using the reference stored in a contactless card presented to the terminal. An Access Controller (3rd party product) The Controller is the element which controls the access rights of the individuals to the secured area. For that reason, it must be located in the secured area. ACCESS CONTROLSYSTEM(*) OR EQUIVALENTNON SECUREDAREAACCESS CONTROLLERTCP/IP, Wiegand, Dataclock, RS485 or RS422ELECTRICLATCH (*)SECUREDAREADry ContactMorphoAccess® SIGMA Extreme TerminalDry ContactALARM

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 1 : Introduction Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 19 The individuals who are authorized to access the secured area have their User ID listed in a so-called "Authorized User List" (in contrast with a banned card list). The MorphoAccess® SIGMA Extreme Series terminal and the Controller are communicating according to one of the TCP/IP, Wiegand, Dataclock or RS485 protocols:  The MorphoAccess® SIGMA Extreme Series terminal sends User ID to the Controller  The Controller sends its decision to the MorphoAccess® SIGMA Extreme Series terminal (which displays access granted or access denied depending on the answer)  The MorphoAccess® SIGMA Extreme Series terminal sends an alarm signal to the Controller as soon as a malicious operation is detected (terminal pulled out from the wall or opened for maintenance operations); refer the paragraph dealing with anti-pulling and anti-tamper switches for more explanations. The Controller is part of the global Access Control System of the secured area, which can provide useful features such as manage:  authorized user lists (i.e. for VIP),  banned card lists (i.e. for lost user cards),  an access request log (who and when, access granted or denied,..),  an event log (i.e. tamper detection, access control for evacuation of the building,...). The MorphoAccess® terminal is able to work alone, without Controller, but the protection level of the secured area is lower. An Alarm (3rd party product) This element is connected to the MorphoAccess® SIGMA Extreme Series terminal through a dry contact. The MorphoAccess® SIGMA Extreme Series terminal sends the command to activate the Alarm as soon as a malicious operation (terminal pulled out from the wall or having its bottom cover opened out of maintenance operations) is detected; refer the paragraph dealing with anti-pulling and anti-tamper switches for more explanations. A Door Electric Latch or equivalent (3rd party product) This element once activated opens the access. The Controller is the one which sends the command to activate the latch if access is granted (i.e. if the individual's User ID is listed in the Controller Authorized User List). Connection between these two elements is done through a dry contact.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 2 :General Description 20 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Section 2 : General Description

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 2 : General Description Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 21 Box opening At the box opening, components shall be extracted from the protection casing as depicted in the pictures below. Extract the wall plate (which is not screwed to the terminal) and keep it separate until the installation of the terminal is completed. The screwing of the product to the wall plate is the last stage of the installation. Figure 2: Box Opening

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 2 :General Description 22 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Components of the initial package Figure 3: Box Content 1. One (1) Terminal’s body 2. One (1) Wall frame

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 2 : General Description Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 23 Terminal's front view description Figure 4: MorphoAccess® SIGMA Extreme Series terminal front view Microphone Status LED Camera Light sensor USB host port 5" WVGA touchscreen LCD Optical biometric sensor Contactless card area Speaker

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 2 :General Description 24 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Terminal's rear view description Figure 5: MorphoAccess® SIGMA Extreme Series terminal rear view Micro SD card slot RJ45 USB port (for configuration and settings with a USB mass storage key, or for installation of a Wi-Fi™ USB dongle) Terminal signal connector RJ45 Wiegand RS485/422 GPIO Power supply Relay Tamper switch

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 2 : General Description Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 25 MorphoAccess® SIGMA Extreme Series Technical Characteristics Item Description Access control modes Identification (search for fingerprint in a local database) Authentication with contactless smartcard, with or without fingerprint check (only if terminal is equipped with a contactless smartcard reader) Multi-factor: identification or authentication (only if terminal is equipped with a contactless smartcard reader) Proxy: the access control check is fully driven by a remote system Man Machine Interface 5” WVGA color capacitive Touchscreen VGA camera for face image capture and videophone Powerful Loudspeaker & Microphone tBiometrics MorphoSmart Optic Biometric Module inside: 23*23mm 500dpi, 256 gray levels optical sensor FBI PIV IQS quality sensor False Acceptance Rate (FAR) adjustable from 1% down to 10-7% Database capacity: 5,000 users (standard) and up to 100 000 users (with specific license) Log capacity 1 000 000 100 000 if face picture logged LAN/WLAN connection For terminal configuration and data transfer: Ethernet 10/100 Base T (MDI, MDI-X) Or Wi-Fi™ Wireless LAN (option), WEP, WPA (PSK) and WPA2 (PSK) encryption available Either TCP, SSL or TLS protocol RFID cards (depending on product version) MIFARE Classic 1KB & 4KB (4b and 7b UID) MIFARE Plus SL1 cards DESFire 3DES legacy 2K, 4K and 8K (EV0 & EV1) DESFire AES 2k, 4k, 8k (EV1) All HID iClass cards (incl. iClass legacy, iClass SR and iClass SE), except 2K2 HID Prox 125 kHz whatever the format (26, 37 ....) Serial port The serial port supports WIEGAND, DATACLOCK (ISO2), RS422 and RS485 protocols GPIO 3 GPI, 3 GPO

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 2 :General Description 26 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Output relay switches Access granted: 1 switch two outputs (normally “open” and normally “closed”) 30V – 1A max (Resistive loads) USB host port External port for terminal configuration through a USB mass storage key Internal port to connect an external Wi-Fi™ USB dongle using an adapter cable Input signals LED1/LED2 to activate the access granted relay Power supply 12 to 24 V DC power supply (1A min @12V) Or by Power Over Ethernet through RJ-45 connector Note for UL 294 Compliance power supply shall be UL 294 and UL 294B with power limited output Security of the terminal Anti-tamper-pulling switches Tamper-pulling detection: one switch closed when product wall mounted, open when pulled out Size and weight W x H x D: 130mm x 300mm x 95mm (5,12” x 11,82” x 3,74”) Weight : ~1,5kg Environmental conditions Operating temperature -20 °C to + 60 °C (-4°F to 140°F) Operating humidity 10 % < RH < 95 % (non condensing) Storage temperature -25 °C to + 70 °C (-13°F to 158°F) Storage humidity 5% < RH < 95 % IP65 rated For UL 294 compliance, the products are rated for indoor use. IP65 was not verified by UL The terminal should be installed in controlled lighting conditions Avoid direct exposure to sunlight or to UV lights Certification planned CE, IEC 60950-1, FCC Part 15, RSS210 - Issue 8 : 2010, RSS-102 - Issue 5 : 2015, RSS-Gen – Issue : 2014, RoHS, REACh, WEEE

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 3 : Installation Procedure Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 27 Section 3 : Installation Procedure

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 3 :Installation Procedure 28 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Before proceeding to the installation  Make sure that you have all the components described in “Components of the initial package” section at your disposal.  Remove the wall plate. Keep this element at hand. Figure 6: Removing wall frame It is then possible to fix the terminal on the wall. The recommended height for fixing of the terminal is 1.30m (camera height). For an optimal use the terminal must be installed in an area where the lighting conditions are controlled. Avoid direct exposure of the sensor to the sun light and ensure good ambient lighting for face detection if used.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 3 : Installation Procedure Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 29 Installation Required tools (not supplied)  Six (6) raw plugs + six (6) screws ø4mm max and length adapted to the wall material.  One (1) screwdriver adapted to screws above.  One (1) Drill (with a drill bit diameter adapted to raw plugs above).  One (1) hole saw (depending on installation case).  A (1) Torx T20 screwdriver  Deadbolt/door strike  Snubber diode required to protect regulated DC power supply from inductive kickback (1N4007 diode or equivalent recommended)  Separate power supply for the deadbolt/door strike based on supplier's recommendations.  External relay (if required)  Networking cable For UL-294 compliance, an earthed screen in the wire or around all wires to/from product is only required when the wires share space/compartment/tube with high voltage cables. Equipment from the initial package to use  One (1) Terminal’s body.  One (1) wall plate.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 3 :Installation Procedure 30 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Step by step procedure Figure 7: Face camera viewing angle The recommended height for fixing of the terminal is 1.30m (camera height). For an optimal use the terminal must be installed in an area where the lighting conditions are controlled. Avoid direct exposure of the sensor to the sun light and ensure good ambient lighting for face detection if used. For face detection, the user has to face the product. Power supply from electrical source shall be switched off before starting the installation. The strength of the attachment depends on the solidity of the wall on which the terminal is mounted. 130cm50,00194cm116cm

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 3 : Installation Procedure Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 31 Drilling the mounting holes Be sure that the wall behind the wall plate has a good flatness. Figure 8: Drilling template If not present, drill in the wall a hole with a diameter adapted to the width of the terminal and the cable to be hosted in (see Figure 8: Drilling template. This template can be found in the Quick Installation Guide). Confirm the presence inside the hole of all the cables needed for the electrical installation (see Electrical Interface) Drill in the wall 6 holes with a diameter adapted to screws and fit them with the raw plugs (see Figure 8: Drilling template). 1300mm40mm minΦ = 4mm2Φ = 4mm1Φ = 4mm4Φ = 4mm3Φ = 4mm6Φ = 4mm5207,00mm97,50mm82,00mmØ44,00mm65,50mm

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 3 :Installation Procedure 32 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Fixing Be sure that a sufficient space is reserved in the wall for the passage of cables, in particular for Ethernet. Figure 9: Wall plate fixing Place the wall plate against the wall, opposite the six holes pierced in the wall (see Figure 9: Wall plate fixing). !127,8mm275,8mm

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 3 : Installation Procedure Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 33 Cabling To ensure water tightness, be sure to bend the cable downward. Cable for wiring shall be AWG 20 to 24, length shall be adapted to the size of the hole in the wall, to terminal connections, and to the distant between the electric source and the terminal itself. Closing Power has to be set up just after closing it. If product has to be stored for a long time (more than 48 hours), don’t forget to restore its configuration before use. Finally, lock the product with the screws at the bottom of the terminal. IP65!

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 34 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Section 4 : Electrical Interface

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 35 Wiring overview Before proceeding, make sure that the person in charge of installation and connections is properly connected to earth, in order to prevent Electrostatic Discharges (ESD). Power supply ground shall not be used for peripheral ground. All other grounds can be used indifferently. Note that all connections of the MorphoAccess® SIGMA Extreme Series terminal described hereafter are of SELV (Safety Electrical Low Voltage) type. Figure 10: Cabling layout

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 36 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Power Supply POE and external power supply are not used at the same time: if both power supplies are used, priority is given to external power supply. If external power supply is shut down, switch to POE without reboot is not guarantee. External Power supply Figure 11: Power supply wiring 25 Red Power Supply 12-24V DC In Positive 12-24 Volts, power supply 26 Black Power ground In Ground power supply External power supply  Must comply with IEC 60950-1 standard.  12V to 24V Dc (regulated and filtered) 1 Amp min at 12V.  Could be provided by a 12 Volts Wiegand power supply, which complies with the Security Industry Association's Wiegand standard March 1995.  If sharing power between devices, each unit must receive 1A (e.g. two units would require a 12vDC, 2A supply). POE (Power Over Ethernet) MorphoAccess® SIGMA Extreme Series terminal's power supply can also be provided by the Ethernet using RJ45 connection (Power Over Ethernet mode - IEEE802.3af or IEEE802.3at type 1 compliant). The terminal maybe alternatively be powered via a UL 294B PSE PoE Limited power source with a range of 48VDC (-10% /+15%). UL 294 compliance was verified with POE (PSE-Power Sourcing Equipment model Phihong part number PSA16u-480).

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 37 Output Relay Figure 12: Output relay wiring 21 Yellow / White Relay NO Contact relay (normally open) 22 Grey / White Relay COM Contact relay common 19 Orange / White Relay NC Contact relay (normally closed) Nominal characteristics of relay Load characteristics:  1 A max @ 30 VDC (according to the safety extra low voltage requirements independently of the power supply),  Resistive load or inductive load; see warning information hereafter for inductive load,  The internal relay is designed for at least 100 000 cycles (resistive load). Inductive load management requires a parallel diode for a better contact lifetime. Example of connection for electrical door locks Figure 13: Example of electric latch connection +VCC <30VImax < 1AElectricdoor lockProtectiondiodeMorphoAccess® SIGMA Extreme TerminalButton on otherside of the doorRelay Pin 1Relay Pin 2

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 38 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Tamper Switch Figure 14: Tamper switch wiring 23 Light Blue Switch 1 Tamper switch contact 24 Pink Switch 2 Strip on tamper switch Operating principle for the switch  Product installed on the wall plate: switch enabled (contact closed).  Product opened (rear connectors accessible): switch disabled (contact open). Nominal characteristics of switch block 100 mA at 30 VDC max (Resistive load) according to the safety extra low voltage standard. This MorphoAccess® SIGMA Extreme Series terminal is part of security system; it is customer’s responsibility to connect the tamper switch (contact) to physical access controller, in order to prevent the access to the connector blocks.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 39 Wiegand wiring Wiegand input Figure 15: Wiegand input wiring 6 Green / Red WIEGAND_IN0 In Wiegand IN D0 (Output type required: Open drain or 5V+/-5%) 3 White / Red WIEGAND_IN1 In Wiegand IN D1 (Output type required: Open drain or 5V+/-5%) 18 Yellow GPO0 (WIEGAND_LEDIN) Out Wiegand LEDIN (typical = 5VDC) (option) 8 Black / Red WIEGAND_GND Ground for Wiegand If pull-up’s to 12V have been added on Wiegand IN D0 and Wiegand IN D1 inputs on a previous installation with a MorphoAccess® 500 Series terminal, these resistors must be removed to avoid any damage to the MorphoAccess® SIGMA Extreme Series terminal.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 40 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Wiegand output The following figure shows how to cable the wires of the serial port of the terminal for the Wiegand protocol Figure 16: Wiegand output wiring 4 Green WIEGAND _OUT0 Out Wiegand OUT D0 (5V TTL) 5 White WIEGAND _OUT1 Out Wiegand OUT D1 (5V TTL) 1 Blue WIEGAND_LEDOUT1 In Wiegand LED IN 1 (option): panel feedback (Output type required: Open drain or 5V+/-5%) 2 Blue / Red WIEGAND_LEDOUT2 In Wiegand LED IN 2 (option): panel feedback (Output type required: Open drain or 5V+/-5%) 8 Black / Red WIEGAND_GND Ground for Wiegand The use of LED1 and LED2 wires is described in the paragraphs below. The controller supports neither LED1 nor LED2 signals When the access controller has no relay contact to provide an answer to the MorphoAccess® terminal, then the decision to emit either the “access granted” signal or the “access denied” signal is taken by another way. It is either the MorphoAccess® terminal itself that decide, or it waits for the access controller answer through the local area network (TCP), or on the serial port in (RS485 or RS422). It is strongly recommended to disable the LED IN feature, to avoid any interference on MorphoAccess terminal behavior. The controller supports only LED1 signal When the access controller has only one relay contact which is dedicated to the “access granted” answer, this one must be connected between the LED1 and GND

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 41 wires. The LED1 wire is set to the low level by closing the contact between the LED1 and the GND wires, and it means “access granted”. The MorphoAccess® terminal uses the timeout of the wait for a low level on the on LED1 wire or LED2 wire as “access denied” answer. To minimize at most the waiting time of the user, the MorphoAccess® SIGMA Extreme Series terminal timeout value, must be adjusted to a value a little bit higher than the maximal value of the controller response time. Warning: if the LED2 wire is connected, it must be constantly maintained in the high state. The controller supports LED1 and LED2 signals When the controller supports one relay contact for each of the possible answers then:  The « access granted » contact must be connected between the LED1 and the GND wires of the terminal  The « access denied » contact must be connected between the LED2 and the GND wires of the terminal. The MorphoAccess® terminal considers that:  The answer of the controller is "access granted", when the controller puts the LED1 wire to the low state (by closing a contact between the LED1 and the GND wires), and leaves the LED2 wire to the high state.  The answer of the controller is "access denied", when the controller puts the LED2 wire to the low state (by closing a contact between the LED2 and the GND wires), whatever is the state of the LED1 wire. The MorphoAccess® terminal also considers that the answer of the controller is "access denied" in case of time-out while expecting for a closure between LED1 and GND wires, or between LED2 and GND wires.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 42 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Serial port wiring DataClock Input Figure 17: Serial port wiring – DataClock Input 6 Green / Red WIEGAND_IN0 In Data (Output type required: Open drain only) 3 White / Red WIEGAND_IN1 In Clock (Output type required: Open drain only) 18 Yellow GPO0 (WIEGAND_LEDIN) Out Card present signal (if configured, only one selectable for Morpho Legacy) 8 Black / Red WIEGAND_GND Ground for Wiegand DataClock Output Figure 18: Serial port wiring – DataClock Output 4 Green WIEGAND _OUT0 Out Data ( 5V TTL ) 5 White WIEGAND _OUT1 Out Clock ( 5V TTL ) 1 Blue WIEGAND_LEDOUT1 In LED IN 1 (option): panel feedback (Output type required: Open drain or 5V+/-5%) 2 Blue / Red WIEGAND_LEDOUT2 In LED IN 2 (option): panel feedback (Output type required: Open drain or 5V+/-5%) 8 Black / Red WIEGAND_GND Ground for Wiegand

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 43 RS485 Figure 19: Serial port wiring – RS485 9 Blue / Black RS485_RXTX+ In/Out RS485 Rx/Tx non inverting signal 11 Blue / White RS485_RXTX- In/Out RS485 Rx/Tx inverting signal 7 Black / Red RS485_GND Ground RS485 implementation is limited to half-duplex communication. So only Tx+, Tx- and ground reference signals are necessary. Depending on the RS485 network, an impedance adaptation may be required. For farthest terminal, a 120-Ohms resistor termination may be added outside the terminal between TX+ and TX-. RS422 Figure 20: Serial port wiring – RS422 9 Blue / Black RS422_RX+ In RS422 non inverting Receive 11 Blue / White RS422_RX- In RS422 inverting Receive 12 Green / Black RS422_TX+ Out RS422 non inverting Transmit 10 Green / White RS422_TX- Out RS422 inverting Transmit 7 Black / Red RS485_GND Ground RS422 interface is a full duplex communication.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 44 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 GPIO wiring Figure 21: GPIO wiring 13 Orange / Black GPI_2 In Digital Input (1,8V to 5V) 14 Yellow / Black GPO_2 Out Digital Output (5V – 5mA max) 15 Orange / Red GPI_1 In Digital Input (1,8V to 5V) 16 Yellow / Red GPO_1 Out Digital Output (5V – 5mA max) 17 Orange GPI_0 In Digital Input (1,8V to 5V) 18 Yellow GPO_0 Out Digital Output (5V – 5mA max) 20 Black / Red GPIO_GND Ground Single Door Access Control (SDAC) implementation Figure 22: SDAC wiring If door contact is not used, GPI1 and GPO1 shall be connected together External Power supplyGPI_1GPO_0Push button /Motion sensorGPI_0GPO_1RELAY_COMRELAY_NO/NCDoor contactDoor strike

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 45 Ethernet connection Ethernet interface can be used to power the MorphoAccess® SIGMA Extreme Series terminal through POE (Power Over Ethernet - IEEE802.3af or IEEE802.3at type 1 mode). According to the POE standard two modes are available: power on data pins and power on dedicated pins. Use either one of these modes depending on POE implementation on your local Ethernet network. Wi-Fi™ dongle must not be used with POE power supply. The POE doesn’t provide enough power for both the terminal and the Wi-Fi USB dongle. Ethernet cable shall be shielded Default Ethernet configuration By default, MorphoAccess® SIGMA Extreme Series terminal is configured in STATIC mode with the following configuration : IP Adress : 192.168.1.10; Gateway Adress : 192.168.1.254; Subnet Mask : 255.255.254.0 Recommendations for RJ45 wiring Pin 1 2 3 4 5 6 7 8 Signals Data pair 1 Data pair 1 Data pair 2 NC/POE pin dedicated (+) NC/POE pin dedicated (+) Data pair 2 Ground/ pin dedicated (-) NC/POE pin dedicated (-) EIA / TIA T568B Colors White orange Orange White green Blue White blue Green White brown Brown EIA / TIA T568A Colors White green White green White green White green White green White green White green White green Corel L120 Colors Grey White Pink Orange Yellow Blue Purple Brown Figure 23: RJ45 wiring RJ45 plug pinout is compliant with 10/100 base T, IEEE802.3 Specification. Product is compliant also with MDI or MDI-X.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 4 :Electrical Interface 46 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 External USB connection Figure 24: External USB connection The external Micro USB can be used for administration only to connect a mass storage USB key (with a standard Micro USB-type A / USB-type A female adapter). This cable can be found in Safran Identity & Security catalogue with ref 293658551. Please refer to MorphoAccess® SIGMA Extreme Series Administration Guide for more information. USB connection is limited to USB key connection (power consumption shall not exceed 200mA)

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 4 : Electrical Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 47 Wi-Fi™ dongle installation Wi-Fi™ dongle shall be installed inside the product and connected to the internal USB Mini B (at the rear of the terminal) using Safran Identity & Security cable provided in the kit. Product integrating Wi-Fi™ dongle shall not be exposed to temperature exceeding 35°C and shall not be exposed to direct sun. Wi-Fi™ feature requires the product to be powered from an external DC 12V to 24V power supply (the POE doesn’t provides enough power for both the terminal and the Wi-Fi™ dongle). Only Wi-Fi™ USB dongle delivered by Safran Identity & Security (kit reference 293686787) may be installed with the terminal for WLAN (Wireless Local Area Network) operation. Cable has to be plugged on the upward USB connector of the rear panel, as on the following image: Figure 25: Wi-Fi™ dongle installation USB extension cord Wi-Fi™ USB dongle

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 5 : User Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 49 Section 5 : User Interface

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 5 :User Interface 50 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Modes for controlling access rights Introduction The MorphoAccess® SIGMA Extreme Series terminal offers several methods for controlling access rights: it needs to be configured in one of the following four modes:  Identification mode,  Authentication mode (requires a contactless smartcard reader in the terminal),  Multi-factor mode (requires a contactless smartcard reader in the terminal),  Proxy mode Refer to MorphoAccess® SIGMA Extreme Series Administration Guide for more information on Access Control. Identification mode The Identification process of the MorphoAccess® SIGMA Extreme Series terminal proceeds by comparison of the biometric data of the finger placed on the biometric sensor, with all the biometric data stored in the database. It means that the biometric data of the allowed users must be stored in the internal database before they can request the access on the terminal. This biometric data is acquired either directly on the terminal (using the embedded), or on an enrolment system using the same type of biometric sensor. The access control by identification process is started when a finger is detected on the biometric sensor When the user requests the access, his identity is unknown, and it is the terminal that searches for his identity. The terminal grants the access if a match is found (the user is identified); otherwise the access is denied (the user remains unknown). For further information, please see the "Identification mode" section in the MorphoAccess® SIGMA Extreme Series Administration Guide. Authentication (verification) mode Unlike the "identification" mode, the user identity must be known in order to execute the authentication process. Indeed, authentication is an identity verification process: the user provides his identity and the terminal checks it with the relevant process. This mode doesn’t compare the user’s data to the data of several users: it compares the data provided by the user with the reference data provided by the same user during enrollment phase. The data can be on a card presented to the terminal or in a database and ID is provided by the user. Access is authorized if the terminal finds a correspondence.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 5 : User Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 51 For further information, please see the "Authentication mode" section in the MorphoAccess® SIGMA Extreme Series Administration Guide. Multi-factor mode In this mode, the "identification" and "authentication" modes are available simultaneously; the user decides which control method will be used:  by placing his finger on the sensor, thereby triggering the identification process,  by placing his contactless card on the reader, thereby triggering the authentication process, This is the default mode for terminals fitted with a contactless smartcard reader. For further information, please see the "Multi-factors method" section in the MorphoAccess® SIGMA Extreme Series Administration Guide. Proxy mode The Proxy mode is an operating mode where the access control main application is located in a distant system. This is not a standalone mode like Identification and Authentication modes. It means that the terminal becomes a slave of the host system application. The access control application is running on the host system and uses MorphoAccess® SIGMA Extreme Series terminal high level functions: • Identification function • Authentication function • Read data on a contactless card • Access control result signal command The MorphoAccess® SIGMA Extreme Series terminal is driven through an Ethernet (or Wi-Fi™) link using TCP, SSL or TLS protocol. The MorphoAccess® SIGMA Extreme Series terminal acts as a server: it is either waiting for a command or executing a command. The commands allowed by the MorphoAccess® SIGMA Extreme Series terminal are described in the MorphoAccess® SIGMA Extreme Series Host System Interface Specification document. For further details about SSL or TLS on the MorphoAccess® SIGMA Extreme Series terminal, please refer to the MorphoAccess® SIGMA Extreme Series Administration Guide. External database mode (also called polling mode) When external database mode is activated, the MorphoAccess® SIGMA Extreme Series terminal does not verify user template in its local database. This mode is useful when the user templates are stored in external database.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 5 :User Interface 52 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 When authentication is initiated on the terminal, the terminal will poll the user ID to external controller. On polling out the ID, the corresponding template (if exists) is fetched from the external database and is authenticated against user’s biometric on the terminal. Once the template request is posted to the external database, the terminal shall wait for the finger template from the external database to start authentication. Further process shall be same as authentication. Polling Process using buffer:  The user’s input ID will be queued in the terminal’s queue, which is polled by external application.  External application waits for the User ID by polling the buffer. After getting an ID, it will search the template in database and send template to terminal for further authentication.  The user is authenticated by the external device and granted access accordingly. MorphoAccess® SIGMA Extreme Series terminal also has distant commands to retrieve polling buffer status and polling buffer data. Refer to the MorphoAccess® SIGMA Extreme Series Host System Interface Specification document. How to Activate? External database mode can be activated through Webserver > Complete Configuration, by setting “ucc.enable_external_database” parameter to 1. Only an admin user can activate polling mode. You can refer to the MorphoAccess® SIGMA Extreme Series Host System Interface Specification document to know how to set this parameter.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 5 : User Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 53 Configuring the terminal MorphoAccess® SIGMA Extreme Series terminals are standalone biometric systems which offers advance features for access control. MorphoAccess® SIGMA Extreme Series terminals are equipped with a facility to support the MorphoAccess® and Bioscrypt legacy systems. When MorphoAccess® SIGMA Extreme Series terminal is set in any of the legacy modes, it supports the database structures and configurations of the selected legacy system. When the terminal is booted for the first time, user can select any of the following modes: MorphoAccess® 500 or J Series legacy mode MorphoAccess® SIGMA Extreme Series terminal can be operated in MorphoAccess® 500 or J series mode (also referred as Legacy Morpho). In this mode, the terminal will support configurations and operations of MorphoAccess® 500 series terminals. Terminal can authenticate users enrolled in the MorphoAccess® 500 series terminal, using biometric check as well as contactless card. New users can also be enrolled in MorphoAccess® 500 series mode. Once the product is configured in Legacy Morpho mode, the following methods can be used to configure the terminal:  through the Ethernet interface (remote management)  through a Wi-Fi™ connection (license and dongle required) Configuration procedures are described inside the MorphoAccess® SIGMA Extreme Series Administration Guide as follows:  Section 4: Terminal Configuration And Administration

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 5 :User Interface 54 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 MorphoAccess® SIGMA Extreme Series native mode MorphoAccess® SIGMA Extreme Series terminal is by default in native mode, that is named MA5G. It will support the new features and configurations only in the native mode. The terminal can be configured using an internet browser connected to the embedded Webserver application. NOTA : When terminal mode is switched from MA5G to Morpho legacy mode, the entire configuration (excepted communication links) and all databases are erased NOTA : The terminal is rebooted on mode change and factory settings are applicable. Once the product is configured in native mode, the following methods can be used to configure the terminal:  through the Ethernet interface (remote management)  through a Wi-Fi™ connection (license and dongle required) Configuration procedures are described inside the MorphoAccess® SIGMA Extreme Series Administration Guide as follows:  Section 4: Terminal Configuration And Administration

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 5 : User Interface Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 55 Anti-tamper / anti-pulling switches Please refer also to “Tamper Switch” section. These switches are activated as soon as there is enough pressure applied on the terminal against the wall. They are deactivated as soon as this pressure is not big enough, e.g. when the terminal is pulled out of the wall. When the switches are deactivated, the MorphoAccess® SIGMA Extreme Series terminal acts as required by the related configuration key (see MorphoAccess® SIGMA Extreme Series Administrator / User Guide for key configuration description):  Ignore the event (default): useful during normal maintenance operations.  Send an alarm message to the Central Access Controller, through the usual channel of the access control result messages (Wiegand, DataClock, RS485, Ethernet or Wi-Fi™). An alarm switch (relay contact) is directly available on block terminal «tamper switch pins». Please refer to “Wiring overview” and to “Tamper Switch” sections.  Generate an audible alarm signal with the speaker and an alert message on the screen.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 6 :Accessories, Software Licenses and PC Applications 56 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Section 6 : Accessories, Software Licenses and PC Applications

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 6 : Accessories, Software Licenses and PC Applications Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 57 Compatible Accessories, Licenses and Software The following items can be ordered directly to Safran Identity & Security or to an official distributor, so as to enjoy all the features of your MorphoAccess® SIGMA Extreme Series terminal:  Power supply units,  Contactless smartcards: MIFARE® 1k, 4k; DESFire® 2k, 4k, 8k,  MA WI-FI PACK: containing a Wi-Fi™ USB dongle and a Wi-Fi™ license to activate Wi-Fi™ capability on your terminal,  User database size licenses (MA_10K_USERS, MA_50K_USERS, MA_100K_USERS): enabling database size upgrade from 3,000 to 10,000, 50,000 or 100,000 users capacity (max 3 fingers per record) at creation of the database. Requires Micro SD card in the terminal.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 6 :Accessories, Software Licenses and PC Applications 58 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Compatible PC applications MorphoAccess® SIGMA Extreme Series terminals are fully compatible with:  MorphoManager (version 10.3.4 or higher)  Morpho Integrator’s Kit (MIK) software development kit (version 6 or higher).  MorphoBioToolBox (version 3.4.3 or higher) Using Legacy Morpho mode, MorphoAccess® SIGMA Extreme Series is also compatible with:  MEMS (version 7.3.1 or higher),  MIK (version 5.4 or higher), The limitations in Morpho Legacy mode are described in the following document: MorphoAccess® SIGMA Extreme Series Release Note - Legacy Morpho limitations

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 59 Section 7 : Recommendations

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 7 :Recommendations 60 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Global warning The manufacturer cannot be held responsible in case of non-compliance with the following recommendations or incorrect use of the terminal. General precautions  Do not attempt to repair your terminal yourself. The manufacturer cannot be held responsible for any damage/accident that may result from attempts to repair components. Any work carried out by non-authorized personnel will invalidate your warranty.  Do not expose your terminal to extreme temperatures.  Use your terminal with original accessories. Attempts to integrate unapproved accessories to the terminal will void your warranty.  Due to electrostatic discharge, and depending on the environment, synthetic carpet should be avoided in areas where the terminal has been installed. Areas containing combustibles It is strongly recommended that you do not install your terminal in the vicinity of gas stations, petroleum processing facilities or any other facility containing flammable or combustible gasses or materials. Specific precautions for terminals equipped with a contactless smartcard reader It is recommended to install terminals equipped with a contactless smartcard reader at a certain distance (> 30cm) from metallic elements such as iron fixations or lift gates or radio product (such as contactless smartcard reader). Performances in terms of contactless badge reading distance will decrease when metallic elements are closer. Ethernet connection It is recommended to use a category 5 shielding cable (120 Ohms). It is also strongly recommended to insert a repeater unit every 90m. Extreme care must be taken while connecting Ethernet wire to the terminal block board since low quality connection may strongly impact Ethernet signal sensibility. It is recommended to connect Rx+ and Rx- with the same twisted-pair wire (and to do the same with Tx+/Tx- and the other twisted-pair wire). Date / Time synchronization The terminal clock has a +/-10 ppm typical time deviation at +25°C (roughly around +/- 6 sec per 48 hours). At lower and higher temperature (but within normal

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 61 operating temperatures), deviation may be more important (worst case: - 14 seconds per 48 hours). If the terminal is used in an application requiring high time precision, we recommend synchronizing regularly your terminal time with an external clock (using NTP). Every 24 hours is usually enough for most applications. Please note that the date/time of the terminal is protected from power failure during at least 24 hours. If the duration of the power failure or power down is longer, the date/time of the terminal will be lost. Cleaning precautions The use of a dry cloth is recommended to clean the terminal, especially the biometric sensor. Acid liquids, alcohol or abrasive materials are prohibited. Legacy mode When terminal mode is switched from MA5G to Morpho legacy mode, the entire configuration (except communication links) and all databases are erased. The terminal is rebooted on mode change and factory settings are applicable. Firmware legacy limitations are described in the MorphoAccess® SIGMA Extreme Series Release Note. Hardware legacy differences are described below: Power supply OMA500 family MA SIGMA Extreme family DC power supply 12V (-15% / +30%) 12V – 24V (-15% / +10%) DC power supply connection Wires Wires Power supply by POE Terminal are compatible with Power Supply Equipment compliants with IEEE802.3af IEEE802.3at type 1 compliant POE power supply connection Block connector and RJ45 connector Only RJ45 connector

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Section 7 :Recommendations 62 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Ethernet communication OMA500 family MA SIGMA Extreme family Block connector and RJ45 connector Only RJ45 connector Serial communications OMA500 family MA SIGMA Extreme family Wiegand Data In - 2 Data Out - 2 LED In - 1 LED Out - 2 Data In - 2 Data Out - 2 LED OUT port LED IN by GPO Dataclock Yes Yes RS485 Half duplex Half duplex RS422 Full duplex (slave and master mode) Full duplex (slave and master mode) GPI/GPO OMA500 family MA SIGMA Extreme family GPI No 3 GPI GPO No 3 GPO (≈ 3 TTLOUT_H only) GPO current limitation - 5mA@5V RELAY OMA500 family MA SIGMA Extreme family Relay pins available NO / NC / COM NO / COM only Driver capabiity 2 A @30V DC (Resistive load) 2 A @30V DC (Resistive load) *: NO: Normally open NC: Normally closed COM: Common

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 1 : Finger Placement Recommendations 64 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Annex 1 : Finger Placement Recommendations

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 65 Main principles Acquisition needs to be done with extreme care, in order to:  get the best image quality  increase recognition performance  reduce recognition time Then, it is highly recommended to:  Maximize the contact between the fingerprint and the sensor  Exert firm, but not excessive, finger pressure on the surface of the sensor  Do not press too hard  Do not slide nor roll the finger across the sensor  Do not move the finger during acquisition  Wait for the extinction of sensor backlight before removing the finger

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 1 : Finger Placement Recommendations 66 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Most useful areas for biometric data Fingerprint central area must be aligned with sensor center Area containing the maximum information

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 67 Position of finger Finger height Align center of 1st phalanx with sensor center Finger angle The finger must be parallel to sensor sides IDEALPOSITION

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 1 : Finger Placement Recommendations 68 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Finger inclination Finger must be parallel to the sensor surface Finger rotation Finger must be parallel to the sensor surface IDEALPOSITIONIDEALPOSITION

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 69 Troubleshooting When finger biometric data acquisition is difficult, please follow the recommendations listed below:  The finger is cold o Solution : warm up the finger  The finger is wet o Solution : wipe the finger  The finger is dry o Solution : warm up the finger and/or add a little bit of humidity  The finger is dirty o Solution: wash hands  Remove bandages or adhesive tapes from the fingerprint area, and from the 2nd phalanx of the finger  Do not press or tense finger to avoid blood vessels constriction

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 2 : Bibliography 70 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Annex 2 : Bibliography

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 71 How to get the latest versions of documents The last version of the documents can be downloaded from our web site at the address below: www.biometric-terminals.com (Login and password required). To request a login, please send us an email to the address below: hotline.biometrics@safrangroup.com

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 2 : Bibliography 72 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Documents concerning the MorphoAccess® terminal Documents about installing the terminal MorphoAccess® SIGMA Extreme Series Installation Guide, Ref. 2017_2000024418 This document describes terminal physical mounting procedure, electrical interfaces and connection procedures. This document is in English. Documents about administrating / using the terminal MorphoAccess® SIGMA Extreme Series Quick User Guide, Ref. 2017_2000024419 This document gives a quick overview of the product and the basics of configuration and use. This document is in English. MorphoAccess® SIGMA Extreme Series Administrator Guide, Ref. 2017_000000XXXX (Not yet available) This document describes the different functions available on the terminal and procedures for configuring the terminal. It also contains the full description of all the configuration parameters for the terminal. This document is in English. MorphoAccess® SIGMA Extreme Series Parameters Guide, Ref. 2016_2000022621 This document contains the full description of all the terminal configuration parameters. This document is in English. Documents for the developer MorphoAccess® SIGMA Extreme Series Host System Interface Specification, Ref. 2016_2000022602 This document describes the commands supported by the MorphoAccess® terminal. This document is in English. MorphoAccess® SIGMA Extreme Series Remote Message Specification, Ref. 2016_2000022373 This document describes the format of messages sent by the terminal to a distant system. This document is in English.

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 73 Release note For each firmware version, a release note is published describing the new features, the supported products, the potential known issues, the upgrade / downgrade limitations, the recommendations, the potential restrictions…

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 3 : Support 74 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Annex 3 : Support

MorphoAccess® SIGMA Extreme Series - Installation Guide Section 7 : Recommendations Identity & Security 2017_2000024418 - Draft V0 January 2017 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 75 Troubleshooting The terminal IP address is unknown or it is not possible to connect to the terminal Use terminal interface to configure a valid set of network parameters in your terminal. The sensor is switched off Check that the database contains at least one record. Check that the identification mode is enabled. The terminal returns erratic responses to Ping commands Check the subnet mask. Ask the network administrator for the correct value. Check that each device connected to the network has a different IP address.

MorphoAccess® SIGMA Extreme Series - Installation Guide Identity & Security Annex 3 : Support 76 This document and the information therein are the property of Safran Identity & Security. They must not be copied or communicated to a third party without the prior written authorization of Safran 2017_2000024418 - Draft V0 January 2017 Technical Support and Hotline North America Mail: cscenter@safrangroup.com Tel: +1 888 940 7477 South America Mail: cscenter@safrangroup.com Tel: +1 714 575 2973 South Africa Mail: sec.san.bio.support@morpho.com Tel: + 27 11 286 5855 India: Mail: support.morphoindia@safrangroup.com Tel: 0120-4699900 Europe and rest of the world: Mail: hotline-biometrics@safrangroup.com Tel: +33 1 30 20 30 40 (9H00am to 5H30pm French Time, Monday to Friday) Web site For the latest firmware, software, document releases, and news, please check our websites :  North and South America : e-mailing cscenter@safrangroup.com with your name, phone number, MA SIGMA serial number and “Send Links For MA SIGMA Extreme Documents” in the subject line  Other countries : please visit our web site www.biometric-terminals.com (To get your log in and password please contact your sales representative).

COPYRIGHT © 2017 Safran Identity & Security Head office: Safran Identity & Security 11, boulevard Gallieni 92130 Issy-les-Moulineaux – France www.safran-identity-security.com