IDP SMART-51L Laminator User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3481317
Application ID	VVggt5DBUhkTBrUmZM6CkA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	481.72kB (6021489 bits)
Date Submitted	2017-07-25 00:00:00
Date Available	2017-07-25 00:00:00
Creation Date	2017-07-25 11:50:31
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-07-25 11:50:48
Document Title	목차
Document Creator	Wordìš© Acrobat PDFMaker 15
Document Author:	Administrator

SMART Series
SMART-51S, SMART-51D, SMART-51L
User Manual
Copyright Notice
Users must respect the copyright laws applicable in their country. This manual must not be
photocopied, translated, reproduced or transmitted in whole or in part for any reason and by the
means that might be, albeit electronic or mechanical, without the express, written authorization
of the company IDP card printer.
All information contained herein may be subject to modification without prior notice.
IDP card printer accepts no liability for any possible errors herein, nor for any accidental
damage or damage caused through the dissemination or the use of this manual.
Trademarks
SMART-51 is a trademark and IDP is a registered trademark of IDP card printer. Windows is
registered trademarks of Microsoft Corp. All other trademarks or registered trademarks are
marks of their respective holders. SMART-51 Design is a trademark of IDP.
Return Materials Authorization
In order to make a warranty claim you must contact an IDP Reseller. You will be responsible for
packaging the printer for shipment and the costs of shipping and insurance of the printer from
the point of use of the printer to the IDP Reseller. The IDP Reseller will bear the costs of
shipping and insuring the printer from the repair location to the address from which the printer
was shipped.
Before returning any equipment for in-warranty or out-of warranty repair, contact an IDP
Reseller or an IDP Service Center for a Return Materials Authorization (RMA) number. Repack
the equipment in the original packing material and mark the RMA number clearly on the outside
of the box. For more information about RMA or IDP warranty statements, refer to the Warranty
booklet on the quick install guide.
Table of Contents
1.
Introduction...................................................................................................................10
1.1
Printer outside features ...................................................................................................... 10
1.2
Printer inside features ........................................................................................................ 13
1.3
Ribbon cartridge features................................................................................................... 15
1.4
Display and Buttons ............................................................................................................ 16
2. Printer installation.............................................................................................................17
2.1.
Connecting a power and a USB cable.............................................................................. 17
2.2.
Fitting the ribbon.................................................................................................................. 19
2.3.
Fitting a laminating film ...................................................................................................... 22
2.4.
Loading the cards ................................................................................................................ 23
2.5.
The withdrawal of printed cards. ...................................................................................... 25
2.6.
Rear Stacker (Option) .......................................................................................................... 26
2.7.
Driver installation (Windows 7 / 8 / 10) ............................................................................ 27
3. Driver configuration..........................................................................................................31
3.1. Printer Properties ................................................................................................................. 31
3.2. Advanced Options................................................................................................................ 34
3.3. Other settings ....................................................................................................................... 37
4. Utilities ................................................................................................................................40
4.1. Card Printer Config .............................................................................................................. 40
4.2. Network configuration ......................................................................................................... 52
4.3. Card Printer Test .................................................................................................................. 61
4.4. Firmware update ................................................................................................................... 68
5. Optional device driver installation.................................................................................70
5.1. Contact smartcard reader ................................................................................................... 70
5.2. Contactless smartcard reader ........................................................................................... 73
6. Troubleshooting ................................................................................................................76
6.1. Error Message ....................................................................................................................... 76
6.2. Cleaning the printer ............................................................................................................. 80
6.3 TPH (Thermal Print Head) replacement............................................................................. 84
6.4. Card movement .................................................................................................................... 86
6.5. Printing quality...................................................................................................................... 87
6.6. Magnetic stripe encoding ................................................................................................... 89
6.7. General operation................................................................................................................. 90
7. Specification ......................................................................................................................92
Table of Figures
Figure 1 SMART-51 front features .................................................................................................................. 10
Figure 2 SMART-51 rear features.................................................................................................................... 11
Figure 3 SMART-51S (Standard) ..................................................................................................................... 12
Figure 4 SMART-51D (Dual) ............................................................................................................................... 12
Figure 5 SMART-51L (Laminator) ................................................................................................................... 12
Figure 6 SMART-51 Inside features ............................................................................................................... 13
Figure 7 Ribbon cartridge features ................................................................................................................ 15
Figure 8 SMART-51 Display and Buttons ................................................................................................... 16
Figure 9 SMART-51S Connection of power and USB cable ............................................................. 17
Figure 10 SMART-51D Connection of power and USB cable........................................................... 17
Figure 11 SMART-51L Connection of powers and USB cable - 1 .................................................. 18
Figure 12 SMART-51L Connection of powers and USB cable - 2 .................................................. 18
Figure 13 Top Cover open .................................................................................................................................. 19
Figure 14 Take out the ribbon cartridge................................................................................................... 19
Figure 15 Loading the ribbon 1 ........................................................................................................................ 20
Figure 16 Loading the ribbon 2 ........................................................................................................................ 20
Figure 17 Installing the cleaning roller ........................................................................................................ 20
Figure 18 Peeling the protective wrapper .................................................................................................. 21
Figure 19 Installing the ribbon cartridge .................................................................................................... 21
Figure 20 Close Top Cover ................................................................................................................................. 21
Figure 21 Take out the film cartridge ............................................................................................................ 22
Figure 22 Loading the laminating film.......................................................................................................... 22
Figure 23 Installing the film cartridge........................................................................................................... 22
Figure 24 Adjusting the card thickness lever .......................................................................................... 23
Figure 25 Preparing the card 1 ......................................................................................................................... 23
Figure 26 Preparing the card 2 ......................................................................................................................... 23
Figure 27 Loading the cards 1 .......................................................................................................................... 24
Figure 28 Loading the cards 2 .......................................................................................................................... 24
Figure 29 Loading the cards 3 .......................................................................................................................... 24
Figure 30 Loading the cards 4 .......................................................................................................................... 24
Figure 31 SMART-51 Withdrawal a card...................................................................................................... 25
Figure 32 SMART-51 Dividing a stacker...................................................................................................... 25
Figure 33 SMART-51S installation of Rear Stacker ............................................................................... 26
Figure 34 SMART-51D installation of Rear Stacker .............................................................................. 26
Figure 35 SMART-51L installation of Rear Stacker ............................................................................... 26
Figure 36 Install Win7 driver 1 .......................................................................................................................... 27
Figure 37 Install Win7 driver 2 .......................................................................................................................... 27
Figure 38 Install Win7 driver 3 .......................................................................................................................... 27
Figure 39 Install Win7 driver 6 .......................................................................................................................... 28
Figure 40 Install Win7 driver 8 .......................................................................................................................... 28
Figure 41 Install Win7 driver 9 .......................................................................................................................... 28
Figure 42 Install Win7 driver 10 ....................................................................................................................... 28
Figure 43 Install Win7 driver 11 ....................................................................................................................... 29
Figure 44 Install Win7 driver 12 ....................................................................................................................... 29
Figure 45 Install Win7 driver 13 ....................................................................................................................... 29
Figure 46 Install Win7 driver 14 ....................................................................................................................... 30
Figure 47 Install Win7 driver 15 ....................................................................................................................... 30
Figure 48 Printer properties............................................................................................................................... 31
Figure 49 Layout ...................................................................................................................................................... 31
Figure 50 Input / Output ....................................................................................................................................... 32
Figure 51 Printing .................................................................................................................................................... 32
Figure 52 Laminating............................................................................................................................................. 33
Figure 53 Encoding ................................................................................................................................................ 34
Figure 54 Printer sharing..................................................................................................................................... 37
Figure 55 Ports ......................................................................................................................................................... 37
Figure 56 Advanced ............................................................................................................................................... 38
Figure 57 Color Management ............................................................................................................................ 38
Figure 58 Security ................................................................................................................................................... 39
Figure 59 Service ..................................................................................................................................................... 39
Figure 60 CardPrinterConfig Log-in .............................................................................................................. 40
Figure 61 CardPrinterConfig start .................................................................................................................. 40
Figure 62 CardPrinterConfig – Card Printer Basic Setup .................................................................. 41
Figure 63 Color density ........................................................................................................................................ 43
Figure 64 Resin Black density .......................................................................................................................... 43
Figure 65 Overlay density ................................................................................................................................... 44
Figure 66 CardPrinterConfig – Card Printer Advanced Setup......................................................... 45
Figure 67 CardPrinterConfig – Flipper Setup ........................................................................................... 48
Figure 68 CardPrinterConfig – Laminator Basic Setup....................................................................... 49
Figure 69 CardPrinterConfig – Laminator Advanced Setup ............................................................. 50
Figure 70 Rear view of SMART-51 printer 1 .............................................................................................. 52
Figure 71 Rear view of SMART-51 printer 2 .............................................................................................. 52
Figure 72 Running the NetAdmin ................................................................................................................... 53
Figure 73 Network printer is not found ........................................................................................................ 53
Figure 74 Connecting to USB port ................................................................................................................. 54
Figure 75 NetAdmin Log-in ................................................................................................................................ 54
Figure 76 USB port state ..................................................................................................................................... 55
Figure 77 Rebooting the network module .................................................................................................. 55
Figure 78 Reset to default ................................................................................................................................... 56
Figure 79 Upgrading the firmware 1 .............................................................................................................. 56
Figure 80 Upgrading the firmware 2 .............................................................................................................. 57
Figure 81 Upgrading the firmware 3 .............................................................................................................. 57
Figure 82 Dynamic IP configuration .............................................................................................................. 58
Figure 83 Static IP configuration .................................................................................................................... 58
Figure 84 Network service configuration ................................................................................................... 59
Figure 85 OCP configuration............................................................................................................................. 59
Figure 86 Network user configuration.......................................................................................................... 60
Figure 87 CardPrinterTest................................................................................................................................... 61
Figure 88 Magnetic stripe encoding .............................................................................................................. 64
Figure 89 Contact smartcard encoding ....................................................................................................... 66
Figure 90 Contactless smartcard encoding .............................................................................................. 67
Figure 91 run CardPrinterFirmware ............................................................................................................... 68
Figure 92 Select Firmware .................................................................................................................................. 68
Figure 93 Update Firmware ................................................................................................................................ 69
Figure 94 Contact smartcard reader driver installation ...................................................................... 70
Figure 95 License agreement............................................................................................................................ 71
Figure 96 Installing the contact smartcard reader driver................................................................... 71
Figure 97 Completing the smartcard reader driver installation...................................................... 72
Figure 98 Found New Hardware Wizard ...................................................................................................... 73
Figure 99 Installation method selection ...................................................................................................... 74
Figure 100 Driver location .................................................................................................................................. 74
Figure 101 Completing the driver installation.......................................................................................... 75
Figure 102 Exclusive cleaning card for SMART-51 printer ............................................................... 80
Figure 103 Printer cleaning start ..................................................................................................................... 80
Figure 104 Printer cleaning Step 1 ................................................................................................................. 81
Figure 105 Printer cleaning Step 2 ................................................................................................................. 81
Figure 106 Printer cleaning Step 3 ................................................................................................................. 82
Figure 107 Printer cleaning Step 4 ................................................................................................................. 82
Figure 108 Printer cleaning Step 5 ................................................................................................................. 83
Figure 109 Printer cleaning Step 6 ................................................................................................................. 83
Figure 110 Thermal Print Head......................................................................................................................... 84
Figure 111 Print head setup............................................................................................................................... 84
Figure 112 Print head replacement ................................................................................................................ 85
Figure 113 Print head angle ............................................................................................................................... 86
Figure 114 Printing quality trouble 1............................................................................................................. 87
Figure 115 Printing quality trouble 2............................................................................................................. 88
Figure 116 Printing quality trouble 3............................................................................................................. 88
Figure 117 Printing quality trouble 4............................................................................................................. 88
Figure 118 Printing quality trouble 5............................................................................................................. 89
1. Introduction
1.1 Printer outside features
For the user’s convenience, SMART-51 status can be seen through LCD with LED and
the printer can be controlled by two LED buttons. It takes a power via the 24V adaptor
provided with the printer. Using USB and Network port, it is communicated with the user’s
PC
The following shows the outside functional features found on the printer.
④
①
③
②
① Top cover open button
② External contactless
Smartcard encoding
position
③ Fan
④ Input hopper
⑤
⑤ LED buttons
⑥
⑥ LCD show the process
status
Figure 1 SMART-51 front features
10
⑦
⑦
Backside card outlet
⑧
Stacker fixing Hole
⑨
Power switch
⑩
24V power connector
⑪
Network port
In case there is no
network option, it is
closed.
⑧
⑨⑩⑪⑫
⑫
Figure 2 SMART-51 rear features
11
USB port
There are three models in SMART-51 card printer series such as SMART-51S, SMART-51D,
SMART-51L.
SMART-51S (Figure.3) is the standard card printer. It can be printed in single side with the
encoding. This manual is prepared based on SMART-51S.
SMART-51D (Figure.4) has a flipper which can enable to print in both sides. SMART-51D can
print the both side of the card with the encoding.
SMART-51L (Figure.5) produces long-life cards for ID and access control with customizable
security features and ability to print smart cards. To cater to expanding requirement in card
security, SMART-51L’s DLW(Direct to Laminating in a Wink) technology provides the most stable
& fast laminating solutions.
Figure 3 SMART-51S (Standard)
Figure 4 SMART-51D (Dual)
Figure 5 SMART-51L (Laminator)
12
1.2 Printer inside features
In SMART printer, the ribbon is installed by a ribbon cartridge which can be used
semipermanently. The following shows the inside functional features found on your
SMART-51 printer.
⑤
②
④
③
①
Figure 6 SMART-51 Inside features
① Output hopper(Stacker)
Collect the printed card and/or encoded cards. Maximum 40 cards are loaded and the
extra printed/encoded card is passed out. It can be withdrawed when pulling forward.
② Input hopper
Load the cards for printing. Maximum 100 cards are loaded when cover is closed;
Maximum 200 cards are loaded when the cover is opened.
③ Card thickness control lever
Adjust the cards thickness.
④ Ribbon cartridge
Install the ribbon and the disposable cleaning roller.
13
⑤ Thermal Print Head
This enables the cards to be printed.
(Caution!: This is very hot after printing. Do not contact the surface of the Thermal
Print Head with fingers or a sharp metal object to avoid degrading print quality or
damaging printer head permanently.)
14
1.3 Ribbon cartridge features
SMART-51 printer uses the same ribbon cartridge as a SMART-50’s.
(However, the ribbon for SMART-51 is incompatible with SMART-50’s.
The color of gear part of the ribbon for SMART-51 is gray.)
②
③
④
①
①
Ribbon cartridge
②
Take up parts
③
Supply parts
Figure 7 Ribbon cartridge features
① Ribbon cartridge
-. Install a ribbon and a disposable cleaning roller provided with the ribbon.
-. This semi-permanent ribbon cartridge is a component of the printer. Printer does
not operate if it is broken or damaged. In this case, please contact printer reseller.
② ③ Take up & Supply parts
-. Ribbon is wrapped to the supply parts as the Picture. It should be installed as the
Figure.7
④ Disposable cleaning roller
-. It removes dust on the surface of card to improve print quality before the card is
printed.
It should be changed together with the ribbon.
-. After installing the disposable cleaning roller to the ribbon cartridge, peel off the
protective film.
-. It is provided with the ribbon.
15
1.4 Display and Buttons
Control panel of Printer consists of 2 lines LCD and 2 buttons. The 2 buttons have the functions
as shown in the Figure 8.
Two Line LCD
Right
Button
Left
Button
Figure 8 SMART-51 Display and Buttons
The status of SMART-51 is ‘Initializing’ when boot up. It is changed to ‘System Ready’ if the
printer is fine. It is change to ‘Printing’ when the printer is working. In case of sensing an error,
it is changed to ‘Error’ status. Whenever the top cover is opened, the operation is stopped and
the status is ‘Top Cover Open’.
The functions of the button under each status are as below table.
Status
Initializing
Left Button
Right Button
N/A
N/A
Ribbon Type/Balance
Sleep
Laminating Film Type/ Balance
Initializing
User Printed Counts
Network IP Address
System Ready
Subnet
Gateway
Network MAC Address
Pulling out the card
Printing
N/A
N/A
Error
Retry
Cancel
Move to backward a card
Move to forward a card
Top Cover Open
Cleaning Mode (when both buttons are pushed)
16
2. Printer installation
2.1. Connecting a power and a USB cable
(1)
SMART-51S
Connect the power and USB cable as the below picture. Please refer to the ‘Network
Configuration’ if you use the LAN connection.
Figure 9 SMART-51S Connection of power and USB cable
(2)
SMART-51D
Connect the power and USB cable after turning the printer on its side as the below
picture. Please refer to the ‘Network Configuration’ if you use the LAN connection.
Figure 10 SMART-51D Connection of power and USB cable
17
(3)
SMART-51L
SMART-51L needs two power cables. Connect powers and USB cable after turning the
printer on its side as the below picture. Please refer to the ‘Network Configuration’ if you
use the LAN connection.
SMART-51L has two power switches so please turn on both switches.
Figure 11 SMART-51L Connection of powers and USB cable - 1
Figure 12 SMART-51L Connection of powers and USB cable - 2
18
2.2. Fitting the ribbon
Before printing, prepare the related items such as a card, a ribbon and a cleaning roller.
In this section we invite you to know the proper method of installing the ribbon and the
cleaning roller into the printer.
(1) Turn off the printer
(2) Open the printer top cover by
pressing the top cover open button.
Figure 13 Top Cover open
(3) Take out the ribbon cartridge.
Figure 14
19
Take out the ribbon cartridge
(4) Install a ribbon into the ribbon
cartridge as the right picture.
Figure 15 Loading the ribbon 1
(5) Insert the supply side of the ribbon
to no.1 hole and press the opposite
(no.2). Insert the take-up side of the
ribbon same method to no.3 and no.4.
After inserting, tighten the ribbon.
①
(Caution! If the ribbon is not tightened, a rolling
up error might be happened.)
③
②
④
Figure 16 Loading the ribbon 2
(6) Install the disposable cleaning roller
to the ribbon cartridge.
Figure 17 Installing the cleaning roller
20
(7) Peel the protective wrapper from the
cleaning roller.
After removing the protective wrapper, the
cleaning roller should be kept clean from
fingerprints, dust and foreign substances
to avoid contamination because it is
adhesive.
(Caution! Do not use without peeling off
the protective wrapper because the
cleaning roller cannot perform its function.)
Figure 18 Peeling the protective wrapper
(8) Install the ribbon cartridge into the
printer after installing the ribbon with a
cleaning roller to the cartridge.
Figure 19 Installing the ribbon cartridge
(9) Close the top cover
(If it is not closed properly, check the
installation state of the ribbon cartridge.)
Figure 20 Close Top Cover
21
2.3. Fitting a laminating film
In case of installation of the laminator, please fit a laminating film as below.
(1) Open the laminator cover by
pressing the laminator cover open
button. Take out the film cartridge.
(Caution: Laminator head is possible to
be HOT. Do not touch it.)
Figure 21 Take out the film cartridge
(2) Insert the laminating film in the same
way of ribbon.
(Caution! If the film is not tightened, a
rolling up error might be happened.)
Figure 22 Loading the laminating film
(3) Install the film cartridge into the
laminator and close the laminator cover.
Figure 23 Installing the film cartridge
22
2.4. Loading the cards
This section shows how to load the plastic cards.
(1) Open the input hopper cover.
Adjust the card thickness with the
card thickness control lever.
(Caution! If the adjustment is not correct, it
will make some error. Use the type of
cards in the specification of this manual.
Always keep the card surface clean state.)
Figure 24 Adjusting the card thickness lever
(2) To separate cards from each
other, push a stack of cards back
and forth to an angle about 45
degrees vertically.
(Static charge makes cards stuck with
significant adhesive force. These cards
must be physically separated from each
other before inserted into the feeder. If not
separated, feeding or printing problems
may occur.)
Figure 25 Preparing the card 1
Figure 26 Preparing the card 2
23
(3) Stand the stack of cards
vertically after separating
Figure 27 Loading the cards 1
(4) Load the cards on the input
hopper properly and close the
hopper cover.
Figure 28 Loading the cards 2
(5) When insert each one card,
insert the card to the end as left
picture
Figure 29 Loading the cards 3
Figure 30 Loading the cards 4
24
2.5. The withdrawal of printed cards.
Printed cards are passed out to the stacker of front bottom side of SMART printer.
Figure 31 SMART-51 Withdrawal a card
SMART-51’s stacker can be divided as following image. so you can withdraw the printed cards
easily.
Figure 32 SMART-51 Dividing a stacker
25
2.6. Rear Stacker (Option)
SMART-51 can install a rear stacker for option at the back of the printer. In case of SMART51S and SMART-51L, please install into the slots at the backside. In case of SMART-51D,
please open the back cover of the printer and install it.
After that, set the value of ‘Card Out’ to ‘Back’ in the CardPrinterConfig Program.
Figure 33 SMART-51S installation of Rear Stacker
Figure 34 SMART-51D installation of Rear Stacker
Figure 35 SMART-51L installation of Rear Stacker
26
2.7. Driver installation (Windows 7 / 8 / 10)
(1) Please insert the installation CD.
Please choose language and click
“Driver Install”.
Figure 36 Install Win7 driver 1
(2) When “User Account Control”
window is opened, click “Yes”
Figure 37 Install Win7 driver 2
(3) STEP 1:
Please turn off printer if it is
connected to PC. Please click
“Next”.
When you click “Next”, older driver
will be removed automatically.
This process will take several minutes to remove
older driver.
You can select the languages by selecting the
combo box as shown on the left picture.
Figure 38 Install Win7 driver 3
27
(4) STEP 2:
When you click “Next”, the driver
installation will be ready.
Figure 39 Install Win7 driver 6
(5) STEP 3: - USB
Please click “Next” if printer is
connected to USB only.
If you want to install the driver for a
printer connected to network, please
select the “TCP/IP Network port” and
select the proper printer as step (7).
Figure 40 Install Win7 driver 8
(6) Please turn on the printer
(Network cable is not supplied. Please
ask network administrator for more
questions.)
Figure 41 Install Win7 driver 9
(7) STEP 3: - Network
Please select the printer that you want
to install in the list and click “OK”.
(If no printer comes out on the window,
please check the connection.)
Figure 42 Install Win7 driver 10
28
(8) When driver installation is
completed, please click “Close”
Figure 43 Install Win7 driver 11
(9) Please open “Devices and
Printers” from “Hardware and
Sound”. Please check if “IDP
SMART-51 Card Printer” is created.
Figure 44 Install Win7 driver 12
(10) Please click the right mouse
button after cursor is placed on “IDP
SMART-51 Card Printer” icon. Click
“Printer properties”.
Figure 45 Install Win7 driver 13
29
(11) Please select “general” tab and
click “Print test page” in “IDP
SMART-51 Card Printer Properties”
window.
Figure 46 Install Win7 driver 14
(12) Please check test card if it is
printed properly and click “Close” if
a card is printed properly.
(If card is not printed or error comes out,
please refer to “Trouble Shooting”.)
Figure 47 Install Win7 driver 15
30
3. Driver configuration
3.1. Printer Properties
To check printer properties, you need to open printer driver. Please open
“Devices and Printers” and right-click “IDP SMART-51 Card Printer”.
Click “Printer Properties”.
(1) Printing Preferences
Please click “Preferences…” shown on the
bottom of the left picture.
Figure 48 Printer properties
(2) Layout
- You can select either horizontal or
vertical printing direction. To apply your
selection, click “OK”.
Figure 49 Layout
31
(3) Input / Output
[ Supply Tray ]
Supply : You can select “Auto” if SMART51 has 1 input hopper. Please select the
hopper if it has a multi hopper.
Tray : You can select “CR-80” because
SMART-51 supports CR80 cards only.
Figure 50 Input / Output
(4) Printing
Do Printing : You can select printing or
not
[ Print Side ]
Side : Please select one side printing or
both sides printing (It is possible only when
you have a flipper.)
[ Front / Back ]
Color : You can select color or mono print.
Flip : You can flip an image
Media / Mask : You can indicate the area
to print by using a predefined mask or user
defined mask (white card, smartcard,
Magnetic stripe card, etc.) on front or back
side.
You can define a mask.
[ Printing ]
User defined mask uses BITMAP file
(1012 X 636 pixels).
Figure 51 Printing
Ribbon : It shows the type of installed
ribbon. You don’t need to select this option
as SMART-51 recognizes ribbon
automatically with RF Tag.
Blue (RGB(0,0,255)): Print and
Overlay
Speed : Set printing speed and quality
Pink (RGB(255,0,255)): Print only
Mode : Set printing mode
Yellow (RGB(255,255,0)): Florescent
Sky Blue (RGB(0,255,255)): Overlay
only
Standard : Default print mode. Prints all
area of printing
32
Partial : Partial print mode. It is printed
partially for the print area only. Printing
speed can be faster than standard mode.
Dither : There are 3 possible selections,
Threshold, Random, and Diffusion Dither.
It is performed with K and KO ribbon only.
(Please select “Diffusion Dither” for high
quality.)
Ribbon Save :
K ribbon Split : You can set the both
sides (Front:YMCO, Back:K) to save color
ribbon(YMCKO, HYMCKO, BYMCKO). It is
only activated while printing both sides
option is set.
(5) Laminating
This tap will be shown only when SMART51L printer is connected to PC.
To set Laminator printing options.
Do Laminating : You can select
laminating or not
Laminator Side : You can select not use,
top side, bottom side and both sides
printing
Overlay : You can select whether overlay
prints or not.
Figure 52 Laminating
Default setting is no overlay when
laminating and we recommend to use the
default value.
33
(6) Encoding
This tap will be shown only when
Magnetic encoder is installed.
Do Encoding : You can select encoding or
not
Coercivity : You can select the coercivity
to encode
Loco : 300, 600 Oe.
HiCo : 2760 Oe.
SpCo : 4000 Oe.
Auto : Defined automatically
Repeat Count : You can select the retry
count to encoding when encoding is failed
Figure 53 Encoding
3.2. Advanced Options
To change the detailed configuration, In the ‘Layout’ tab shown, Please click
“Advanced…” shown on the bottom of the ‘Layout’ tab of the ‘Preferences’.
 Reset Default Values: Reset to default.
 Color Correction: You can correct gamma for colors. You need to use
CardPrinterConfig to adjust color densities.
Main [-100:100] : Correct gamma for all panels
Yellow [-100:100] : Correct gamma for yellow panel
Magenta [-100:100] : Correct gamma for magenta panel
Cyan [-100:100] : Correct gamma for cyan panel
Black [-100:100] : Correct gamma for black panel
Overlay [-100:100] : Correct gamma for overlay panel
34


Position Processing: Set criteria for resin black processing.
Color [-32:32]: to set the position of color panels
Mono [-32:32]: to set the position of resin or mono panel
Overlay [-32:32]: to set the position of overlay panel
Resin Black(K) Processing: Set criteria for resin black processing.
Text [0:100]: to set density criteria for extracting black objects
Dot [0:100]: to set density criteria for extracting black dots
Threshold [0:100]: to set density criteria on dithering
Dithering Degree [0:100]: to set sharpness on dithering
Resin Extraction: You can set the method to extract resin black when you use
design programs. (If you use the SmartID, you don’t need to select this option.) It
will be set automatically.

Black Object: to extract resin black automatically for text, line, box,
circle, binary images, etc.

Black Text: to extract resin black for text only

Black Dots: to extract resin black for all of black

Black Dots only: to extract resin black for all of black and not to print on
color panels


Not Use: not to extract resin black
Extra Controls : Other options
Fast Alignment [On/Off]: to set the position of input card to the magnetic
encoder or normal printing. If it is on, the printer can save the time to encode

Rewritable Erase Density [0:100] : to set Erase Density on Rewritable printer
Wait Option:
Wait at Internal Module Contactless Encoding Position [On/Off]: to set
whether to wait at the Internal RF encoder or not
35

Card Side [Front/Back]: to set the direction of card when waiting

Wait Position [-100:100]: to set the position of card to wait from the
criteria position. Unit is 0.1mm

Wait Time [0:1000]: to set time to wait. Unit is second
Wait at External Module Contactless Encoding Position [On/Off]: to set
whether to wait at the External RF encoder or not

Card Side [Front/Back]: to set the direction of card when waiting

Wait Position [-100:100]: to set the position of card to wait from the
criteria position. Unit is 0.1mm

Wait Time [0:1000]: to set time to wait. Unit is second
Wait at Internal Module Contact Encoding Position [On/Off]: to set whether to
wait at the Internal IC encoder or not

Card Side [Front/Back]: to set the direction of card when waiting

Wait Position [-100:100]: to set the position of card to wait from the
criteria position. Unit is 0.1mm
 Wait Time [0:1000]: to set time to wait. Unit is second
36
3.3. Other settings
(1) Sharing
You can share a printer with Sharing tab
via Network.
Default is unchecked “Share this printer”.
Figure 54 Printer sharing
(2) Ports
Port tab shows which port is connected
with SMART-51. SMART-51 has
connection with USB Virtual printer port as
left picture because SMART-51 uses USB
connected to PC.
(Caution! This port is selected
automatically. It is recommended to
maintain default.)
Figure 55 Ports
37
(3) Advanced
It is available for Working Time setting,
Priority order, Spool print etc. in
“Advanced” tab. “Advanced” setting follows
MS Windows standard. If you want to
change the setting, please refer to the
Window manual.
(It is recommended to maintain default.)
Figure 56 Advanced
(4) Color Management
In “Color management” tab, you can select
color management profile fit to the printer.
SMART-51 uses color profile to express
optimal color. The driver selects color
profile automatically to fit each ribbon.
(It is recommended to maintain default.)
Figure 57 Color Management
38
(5) Security
You can set the permission to use a printer.
Depend on the permission, the certain
group or user can print, manage the
printer/documents or not.
Figure 58 Security
(6) Service
You can recognize the modules to connect,
printer serial, printer ID, driver version,
firmware version, type of ribbon & balance
and printer’s status.
You can print the “technical support sheet”
on a card to check printer’s setup value.
To clean printer, please insert a cleaning
card in a hopper and click “Clean Printer”.
For further details, please refer to “6.2.
Cleaning Printer”.
Figure 59 Service
39
4. Utilities
4.1. Card Printer Config
SMART-51 is produced with optimized setting. You need to adjust setting value if
required or spare parts are replaced using CardPrinterConfig in our Installation CD.
You can adjust following settings with CardPrinterConfig.
(1) Run CardPrinterConfig
Password input window is displayed when
you run this program. If you input the
correct password, the recorded setup value
will be shown and you can change values.
The password is saved to SMART-51
printer. So if you use another PC with same
printer, previous password is required to
run this program. (Default password is
none. Please press OK if you have not set
password.)
Figure 60 CardPrinterConfig Log-in
When you are successful to log-in, you can
set values shown as left picture.
Figure 61 CardPrinterConfig start
40
(2) Card Printer Basic Setup
②
①
③
④
⑤
⑥
⑨
⑦
⑧
⑩
Figure 62 CardPrinterConfig – Card Printer Basic Setup
① To show connected printers
Device: You can select a printer using pull-down menu. “IDP SMART-51 Card
Printer” is a name of printer. “SMART1” is printer ID, “USB005” is connected port.
If you connect the Network printer, please check the “Allow Network Printer” and
select in the pull-down menu.
② To set administrator password and user password.
Change Root PW: To set administrator (root) password. This password is used to
verify user authority for CardPrinterConfig and User Authentication. Also it is
required for User password management. (Please set password for security use.)
Change User PW: To set user password for User Authentication.
41
③ Click “Card Printer” tab.(If laminator or flipper is installed, you can setup laminator
or flipper setting value by “Laminator” tab or “Flipper” tab..
④ To show firmware version, serial number of printer and serial number, resister &
type of print head.
⑤ To show print area. It shows exaggeratingly for user convenience.
⑥ To set print area. Please set it properly to print on an entire card because SMART51 is a direct thermal card printer. When you click “⑦ Print”, a card is printed as
like “④ example”. Please set values properly that all circles of each corner are
printed and blank spaces are 0.4mm ~ 0.5mm in the top and the bottom of a card.
Please set values by following order.
X Start Position: Please set right and left properly by adjusting X position.
Y Start Position: Please set the start position of printed example image and
blank space in the top is 0.4mm ~ 0.5mm.
Y End Position: Please set the end position of printed example image and blank
space in the bottom is 0.4mm ~ 0.5mm. It is recommended to set bigger
value for “Y scale” than default.
Y Scale: Please set to show circles in the bottom.
⑦ To set density. SMART-51 enables to set different density for each color, resin
black and overlay. So, please set each density for high quality. Please optimize
the quality by adjusting each value. To optimize, you repeatedly adjust the density
and print a Calibration card and check the print state until you get the optimum.
Total Density: To set all of the density (Color, Black and Overlay) at one time.
YMC Density: To set color density. Please maximize YMC density as you can,
which enables to express range of color and vivid images. If it is too strong, green
or red marks are appeared. If it is too weak, the print quality will be dull.
42
Figure 63 Color density
Black Density: To set resin black density. In the picture, barcode is printed to
express density.
When density is too strong, barcode is printed too thick. When density is too weak,
barcode is too thin. Please adjust resin black density to express clear barcode.
Please refer to the following pictures.
Figure 64 Resin Black density
Overlay Density: To set overlay density. Please set it when overlay is printed on
surface regularly. If it is too strong, it is hazy and marks are appeared. If it is too
weak, overlay panel is not printed edge areas. You can check it with printed card
under the light.
43
Figure 65 Overlay density
⑧ To print calibration card.
⑨ To show advanced Setup.
(It is recommended not to set advanced setup.)
⑩ To load or save values.
Get Config.: to get values from current printer
Set Config. : to set values to current printer
Load from File: to load values from file
Save to File : to save values to file
Load Default : to load default. Please adjust values again after load default.
Close : to close CardPrinterConfig
44
(3) Card Printer Advanced Setup
You can set more values.
①
②
③
④
Figure 66 CardPrinterConfig – Card Printer Advanced Setup
① You can set Printer ID, PC serial, Print head and Magnetic encryption key.
Change Printer ID: When SMART-51 is used by SDK, you can set unique ID for
SMART-51 printer regardless of whether it is connected by USB or what IP address is.
It is useful to connect and use several printers. Default is “SMART”.
Set PC Serial: One of security function. You can use a printer with specific PC.
It is activated when you click “Set PC Serial” after “PC Auth.” of ④ is checked and
rebooted. At that time, the specific information of used PC is saved to SMART-51
printer.
Change Head: When you replace thermal print head, you must change head
information for optimal quality. Please change head serial number, resistor and type of
head in the Change Head Dialog window after click “Change Head”.
45
Set Mag. Encrypt Key: One of security function. When you use SDK, you can encrypt
magnetic stripe encoding data transmitted by USB. You can define and save the
encryption key to SMART-51 using “Set Mag. Encrypt Key”.
② To show how many cards are issued with SMART-51 printer. “Total Issue Count” is the
number of issued cards from factory shipment, “User Issue Count” is the number of
issued cards from replacing head. When you replace a head, please initialize the
number by ticking “Reset User Issue Count”.
③ To show ribbon motor management. SMART-51 recognizes ribbon color automatically
and controls motor by ribbon remaining. “RMP+”, “RMP-“, “RMM+”, “RMM-“ are
necessary variables to control ribbon motor. Please do not change values for them as
it affects card quality.
RMP+: Set the ribbon motor’s max torque value while printing when the balance is
max.
RMP- : Set the ribbon motor’s min torque value while printing when the balance is min.
RMM+: Set the ribbon motor’s max torque value while moving when the balance is
max.
RMM- : Set the ribbon motor’s min torque value while moving when the balance is min.
Ribbon Position: Set the ribbon arrangement position
Ribbon Search Mode: Set the ribbon Search method
Print Wait Time: Set the time from lifting down the print head to starting print
Initial Flipper Angle: Set the angle of flipper when card is out if the ‘Card Out’ is
‘Back’
④ Please refer as below for other values.
Display Type: Set a type of LCD display module
UART Baud Rate: Set the speed of communication of Internal Serial port. It is used for
the KIOSK model.
Security: There are several ways to set a security function for SMART-51.
PC Auth.: You can use a printer with specific PC. It is activated when you click “Set
PC Serial”.
User/Root Auth.: You can set passwords for User and Administrator.
DCL Mode: When you use SDK and print cards with DCL mode, you don’t need to
install printer device driver.
46
SBS Only: Please enable it when you issue cards with software programed by SDK.
This option disables printer device driver.
Safe Head Heat: Set not to print if the print head is overheated.
Cleaning Warning: Set to show the ‘Do cleaning’ message periodically
Use USB Serial: When SMART-51 is connected to USB, it transmits the USB serial
number to PC. Default is the same number used by all SMART-51. Please set this
option when you use multiple SMART-51 printers connected to 1 PC via USB. It
enables unique serial numbers for each USB.
Mag. Head Position: SMART-51 can install the magnetic encoder on upper/lower side
of a card. You can set it depending on the position of encoder.
Card Out: Set the way to eject cards.
Error Card Out: Set the way to eject error cards.
Auto Front Card In: Set to input a card automatically if the front card-in sensor
detects a card. It is used for the KIOSK model.
Auto Rear Card In: Set to input a card automatically if the rear card-in sensor detects
a card. It is used for the KIOSK model.
Dump Mode: It records log data to inspect the operation of printer.
User Mag. Current: The default current value when the user selects to use the
defined value when magnetic encoding
Mag. Write Mode: You can order the way how to encode magnetic stripe.
“L:A, H:I”: encodes 3 tracks at once for LoCo card and encodes at twice by dividing 1,3
and 2 track for HiCo card.
Magnetic Start Position: Set the start position of magnetic stripe when you encode.
Card In Speed: set the speed of inputting a card
Card Move Speed: set the speed of moving a card
Card Eject Speed: set the speed of ejecting a card
47
(4) Flipper Setup
This ‘Flipper’ tab is shown when the flipper option is installed.
①
②
Figure 67 CardPrinterConfig – Flipper Setup
① To show installed flipper
Firmware version and serial number of flipper
② To set configuration of flipper
Device Attribute: Basic attribute of flipper
Card In Speed: Set the speed of inputting a card into a flipper
Cade Move Speed: Set
Card Eject Speed: Set
the speed of moving a card in the flipper
the speed of ejecting a card from the flipper
48
(5) Laminator Basic Setup
This ‘Laminator’ tab is shown when the laminator option is installed.
①
②
④
③
Figure 68 CardPrinterConfig – Laminator Basic Setup
① It shows the information of installed laminator such as firm-ware version, serial
number.
② The fields show laminator film’s type, balance, code and laminator code.
Film Type : It shows installed film’s type and vendor code.
Film Remain : It shows installed film’s total number and balance.
Laminator Code : It shows Laminator’s code, vendor and local code.
Film Code : It shows installed film code, vendor and local code.
③ You can change the values according to the installed film type.
49
Heater Temperature : It is for laminating temperature.
Laminating PPS : Laminating speed.
Laminating Move Pulse : The distance of laminating movement.
Separation with Card : After laminating and removing film, the value changes the
distance of card movement
Separation with Film : After laminating and removing film, the value changes the
Distance of film movement.
Lami. Start Card Pos : The value is for laminating start position.
Torque Laminating Max : Maximum torque of motor while laminating.
Torque Laminating Min : Minimum torque of motor while laminating.
Laminating with Pulse : The value is for change laminating width.
Film Attribution : It changes film attribution.
④ It shows “Advanced Setup” window.
(6) Laminator Advanced Setup
①
②
Figure 69 CardPrinterConfig – Laminator Advanced Setup
50
① It shows total laminating count.
② You can change other configurations of laminator
Torque Move Max: Change Maximum motor torque
Torque Move Min: Change Minimum motor torque
Head Motor Torque: Change head motor torque
Device Attribute: The attribute value of laminator
In Speed: Set the speed of inputting a card into a laminator
Out Speed: Set the speed of ejecting a card from the laminator
Move Speed: Set the speed of moving a card in the laminator
51
4.2. Network configuration
(1) Connecting network port
The printer which installed with
network option has a port for
network connection as shown in the
left picture.
① Power Switch
② Power Supply Connector
③ Network Port
④ USB Port
①②③④
Figure 70 Rear view of SMART-51 printer 1
Please connect network cable
(RJ45) to a printer.
(Network cable is not supplied. Please ask
network administrator for more questions.)
Figure 71 Rear view of SMART-51 printer 2
DHCP (Dynamic Host Configuration Protocol) which automatically assigns IP address to the
SMART-51 network printer on the same network is default for IP configuration. If you don’t have
DHCP server, you need to set static IP.
Please run NetAdmin.exe in the SMART-51 installation CD to set or change network
configuration.
52
(2) Network configuration
NetAdmin is run as the Pic.72 after
turning on SMART-51 network
printer.
① Printer Connection Status
Searches local network, finds and
shows available network printer.
①
②
③
② Network Module Management
Searches connected encoder on
network module. Reboots, Resets
network module. Firmware upgrade
available
③ Printer Configuration
Sets detailed system configuration.
④
④ Network Information
Shows firmware version of network
module
Figure 72 Running the NetAdmin
When no printer is connected to
network, there is no printer shown
on the box.
Please click “Refresh”.
If no printer shown, please check as
below,
1. Please check the printer is turned on.
2. Please check network cable is
connected to network hub and works
properly (LED lamp blinking).
3. Please check if there is DHCP server
in the local network. When DHCP
server is not in your local network,
you need to set Static IP.
Figure 73 Network printer is not found
4. If Static IP is used, please check the
IP configuration. If another device
uses same IP address, it doesn't
work.
53
If you are unable to find printer in
local network, please connect printer
by USB. You can setup network by
USB.
When you click Refresh, you can find a
printer connected by USB as shown in the
left picture..

You don’t need to install device driver
for network configuration by USB.
Please ignore messages related to
device installation.

You can change values of “System
Management” only when you connect a
printer by USB. Please connect a printer
by network to use all of the functions of
Netadmin.exe.
Figure 74 Connecting to USB port
Please select a proper printer and
click “connect”. Please enter
password and click “OK”.
Default password is “admin”.
Figure 75 NetAdmin Log-in
54
“USB port state” shows USB device
status connected on network
module.

Network module has 4 USB ports.

Network module supports PC/SC.
When you install the encoders that
support PC/SC on network module, you
can recognize the status of encoders.
Figure 76 USB port state
“Reboot module” reboots network
module.

Please click “Yes” when pop-up window
comes out for reboot.

It takes 1 minute to reboot.

Please click “Refresh” after reboot.
When proper printer shown, please
connect printer by clicking “Connect”.
Figure 77 Rebooting the network module
55
“Reset to default” resets to default
and reboot network module.

Please click “Yes” when pop-up window
comes out for reset.

It takes 1 minute to reboot.

Please click “Refresh” after reboot.
When proper printer shown, please
connect printer by clicking “Connect”.
Figure 78 Reset to default
“Upgrade firmware” enables to
upgrade firmware of network
module.

You can choose a firmware file.
Figure 79 Upgrading the firmware 1
56

Warning box will be shown during
firmware upgrade for network module.

It is recommended not to do other work
during firmware upgrade for system
reliability.

Please do not turn off a printer until the
upgrade is completed.
Figure 80 Upgrading the firmware 2

When firmware upgrade is completed,
pop-up comes out for reboot. Please
click “Yes”.

It takes 1 minute to reboot.

Please click “Refresh” after reboot.
When proper printer shown, please
connect printer by clicking “Connect”.
Figure 81 Upgrading the firmware 3
57
If you setup network automatically,
please choose DHCP.
 Please select DHCP or Static.
 “DHCP” is default for SMART-51 printer.
 Please enter values for “IP”, “Network
Mask”, and “Gateway”. Click “Set
Configuration”.
 Static IP is recommended. DHCP server
assigns IP address automatically but
this IP address is temporary, so the IP
address may be changed. In this case,
the network error may occur in
connecting to SMART-51 network
printer.
Figure 82 Dynamic IP configuration
 If you are not aware of static IP, please
ask network administrator for Static IP.
 We recommend using Static IP because
it is more stable for using SMART-51
network printer.
Wireless Network Configuration
 For wireless network, the WIFI option
should be installed in the Network
Module
 Check “WiFi (Option)” button to activate
it
 Enter the ESSID value in “WiFi ESSID”
to access
 Enter the Key value in “WiFi Key”
 Set the IP address as the same way of
LAN network
 Click “Set Configuration” to save the
configuration value and reboot the
printer
Figure 83 Static IP configuration
58
You can change Service
Configuration.

SMART-51 network printer provides 3
kinds of service (change “USB Spool”,
“Network Spool” and “Network SDK”).
You can select and change the service
according to the need.

In “Network SDK”, you can control the
printer and print a card well, and the
printer supports SSL (Secure Sockets
Layer) and User Authentication for
security.

Please use default and ask technician
for details.
Figure 84 Network service configuration
You can use Open Card Print
function.

This function is for send commands and
print through network card regardless of
OS

Click check box “Use OCP”

“Use Terminal Emulation” is value for
getting echo according to the
commands through terminal. For
security, it supports SSL and User
Authentication.

Please do not change default value
except special case..
Figure 85 OCP configuration
59
You can add, change, delete User
and change its password.

“admin” is administrator and you can’t
delete this account. Please don’t forget
password for “admin”

“Get User”: shows available users

“Add User”: makes new user

“Del User”: deletes selected user

“Change Password”: changes password
Figure 86 Network user configuration
60
4.3. Card Printer Test
Basically Card Printer use standard printer device so you can be used same as general
paper printer. In the case of magnetic stripe, contact, contactless encoder option, you
will need to install appropriate driver and operate individually. Encoding operation will be
controlled by “CARD PRINTER SDK”. You can test all feature of printer by Card printer
Test. Card Printer Test program is developed by using “SMART Printer SDK”
(1) CardPrinterTest
When CardPrinterTest is run, all function can be tested individually.
①
②
③
④
⑥
⑤
⑦
Figure 87 CardPrinterTest
① Select Printer: select printer to test. In the picture, “IDP SMART-51 Card Printer”
is the Printer name, SMART1 is the Printer ID, and USB005 is the connected port.
② Control : To execute each step to test
③ Print: Print test with CSD file which is designed by Smart Design program.
61
④ Batch Start: Repeat selected encoding test by “⑤ Encoding”
⑤ Encoding: Encode Magnetic Stripe, Contact Card, Contactless Card
⑥ Printer Status: Check printer status.
⑦ Message: Description of status by log.
(2) Select printer and control
When you execute CardPrinterTest, it will search connected printers by USB and Network
automatically and SMART-51 printer connected to USB has higher priority. Other printers could
be selected by pull-down menu. You can test all function with connected printer.
. Control is consisted by SBS(Step by Step), Move, Rotate, Etc. section and you can control
printer by each step.

SBS
SBS is to operate SMART-51 printer in SBS(Step-By-Step) mode which you can
control the printer using commands. In SBS mode, after printing data transmission,
printing a card will be run only by clicking “DoPrint”. It is the main difference between
NORMAL mode and SBS mode. When you click “Start”, SMART-51 is operated in
SBS mode, and existing spooled data will be eliminated. To exit SBS mode, click
“Stop”.

Card
Card is to bring a card into printer and eject a card. “In” is to move a card from input
hopper to printer and “Out” is to move a card from printer to output hopper. In case
the flipper is installed, “Back” ejects a card to the back side.

Move
Move is to move a card to specific position in the inside of printer. “Print” is to move a
card to the printing position, and “Mag.” is to the magnetic encoding position, and “IC”
is to the contact smartcard encoding position, and “RF” is to the contactless
smartcard encoding position. “To Rotator” is to move a card from printer to flipper and
“From Rotator” is to move a card from flipper to printer. “from In” is to move a card
from the card in sensor to where you define position, and “from Out” is to move a card
from the card out sensor to where you define position.
62

Rotate
Rotator is to flip over a card in the printer installed flipper. “Auto” is to move a card
from printer to flipper and flip over a card and move a card to the printing position
automatically. “Batch” is to repeat “Auto” as many times as the number of set. “To
Bottom” is to turn to the backside of card and “To Top” is to turn to the front side of
card.

Etc
“Cleaning Roller” is to clean the roller by cleaning card automatically. “Use Log” is to
display log in message space.
(3) Print
Print can be done through the CSD file which is designed by Smart Design program.
Following the steps in this section.
1. Click “…” button and select the CSD file.
2. Click “Open” button to prepare CSD file to print.
3.
Click “Print” Button to move print data to spool. In the NORMAL mode, Click “Print”
button to print a card, but in the SBS mode, “Print” button to transmit a printing data
from PC to printer and wait for printing. Therefore, you must click “DoPrint” to print in
SBS mode. This function is for detail control of printer.
4. Click “Close” button to close CSD file.
(4) Batch
Batch is to repeat encoding/decoding test continuously. In the Repeat, you input the number of
repeat and click “Batch Start”, then the test is run as many times as the number of set. When
you check “Include Card In/Out”, each time the printer bring a card from input hopper and
perform an encoding test and eject the card. But if not, encoding test will be done only by one
card. At that time, if there is no card in the printer, the printer bring a card into the printer from
input hopper and repeat the encoding test on the card, and if there is a card in the printer, the
encoding test is performed on the card repeatedly. “Card Holding” is activated when “Include
Card In/Out” is ticked. When “Card Holding” is ticked and the repeat number is set, the printer
repeats the encoding test as many times as the number of set in the “Card Holding” without
ejection. When it is completed, the printer ejects the card and brings a new card into the printer
and starts testing.
63
In the Setting, “Retry” is to retry the encoding test when the error occurred. “Prompt on Error”
is to display Pop up Message when the error occurred. If not, Error number will be counted
without message. The number of error is displayed at Error section.
(5) Encoding
Magnetic: Magnet Stripe Encoding
“Read” is to read and display the data from magnetic stripe card. It is composed of
“Do Read” and “Read All Buffer” and runs “Do Read” and “Read All Buffer” sequentially.
“Do Read” is to read the data from magnetic stripe card and store the data in the
buffer.
“Read All Buffer” is to transmit the date stored in the buffer to PC. If the track number
is ticked, the data of the ticked track is only transmitted to PC.
“Write” is to write the data to the magnetic stripe. It is composed of “Write All Buffer”
and “Do Write” and runs “Write All Buffer” and “Do Write” sequentially.
“Write All Buffer” is to transmit the data to the buffer.
“Do Write” is to write the data stored in the buffer to the magnetic stripe of card. You
can choose the magnetic foil type (LoCo or HiCo) and the track of magnetic stripe.
“Random Fill” is to create a random magnetic encoding data for testing.
Batch process repeats the following steps sequentially, Card “IN”  Move “Mag” 
Magnetic “Random Fill”  Magnetic “Write”  Magnetic “Read”  Card “OUT”.
Figure 88 Magnetic stripe encoding
64
IC(PC/SC) : Contact Smartcard Encoding
In SMART-51 printer, a contact smartcard encoder can be installed and SMART-51
printer supports the contact smartcard encoder in the printer inside and the SIM
encoder on the right of front side. “IC(PC/SC)” is to test a contact smartcard and SIM
encoding.
“Batch” is applied only to the contact smartcard encoding because SIM encoder is
installed outside and can’t move a card automatically.
“ICH Contact” is to bring the encoder head into contact with the IC chip of smartcard
physically.
“ICH Discontact” is to separate the encoder head from the IC chip of smartcard
physically.
“Init” is to recognize and display the installed contact smartcard reader. The
recognized encoder will be displayed at the pull down control.
“Contact” is to contact with the smartcard electrically and initialize.
“Reset” is to finish the function electrically. After “Contact”, you can run “Get ATR”,
“Read”, “Write” and “Clear”.
“Get ATR” is to read the ATR data.
“Read” and “Write” are to read and write the defined data (Name, Address and
Phone). These could not be applied to all cards.
“Clear” is to clear the displayed data (ATR, Name, Address and Phone).
In case the data is read and written using APDU, Read/Write can be done by APDU
commands.
“Load APDU” is to read the stored APDU commands.
“Save APDU” is to save the displayed APDU commands.
“Clear APDU” is to clear the APDU section.
“Send APDU” is to run the APDU commands.
Batch process repeats the following steps sequentially, Card “IN”  Move “IC”  IC
“ICH Contact”  IC “Init”  IC “Contact”  IC “Reset”  IC “ICH Dis-contact”
 Card “OUT”.
65
Figure 89 Contact smartcard encoding
RF(PC/SC) : Contactless Smartcard Encoding
In SMART-51 printer, a contactless smartcard encoder can be installed and SMART51 printer has the internal and external contactless smartcard encoder. RF(PC/SC) is
to read and write the contactless smartcard. Using internal encoder, the printer brings
a card into the printer from input hopper and encodes a smartcard. Using external
encoder, after putting a card on the top cover, you can encode because the antenna
installed under the top cover is used. Therefore, “Batch” is applied only to the internal
contactless smartcard encoding.
“Contact” is to contact with the contactless smartcard electrically and initialize.
“Reset” is to finish the function electrically. After “Contact”, you can run “Read”, “Write”
and “Clear”.
“Get UID” is for getting Chip Serial Number(CSN)
“Read” and “Write” are to read and write the defined data (Name, Address and
Phone). These could not be applied to all cards.
“Clear” is to clear the displayed data (ATR, Name, Address and Phone).
In case the data is read and written using APDU, Read/Write can be done by APDU
commands.
“Load APDU” is to read the stored APDU commands.
66
“Save APDU” is to save the displayed APDU commands.
“Clear APDU” is to clear the APDU section.
“Send APDU” is to run the APDU commands.
Batch process repeats the following steps sequentially, Card “IN”  Move “RF” 
RF “Connect”  Get UID RF “Discontact”  Card “OUT”
Figure 90 Contactless smartcard encoding
(6) Printer status
“Get Temperature” is to get and display the temperature of Thermal Print Head. When the
“Realtime Check” is ticked, it displays the current temperature of Thermal Print Head in real
time.
“Get Status” is to get and display the printer status.
Please refer to the ‘SMART SDK manual’ for the status code.
67
4.4. Firmware update
When you run the CardPrinterFirmware, you can see the pop-up window.
(1) CardPrinterFirmware Menu
Device: Select the local printer that you
want to upgrade.
Card Printer / Flipper / Laminator: Select
the device you want upgrade.
Device Version: Displays the current
firmware version of selected printer.
Binary File: Click “Browse” button and
select new firmware file to update.
Figure 91 run CardPrinterFirmware
Manual Update: It is used when you want
to update manually.
Update: Updates automatically. In
generally, we recommend updating
automatically.
Close: Exit.
Message : It displays information of
updating.
(2) Ready for Firmware Update

Select the printer to update the
firmware on the ‘Device’ list.

Select the device to update the
firmware among
Printer/Flipper/Laminator tab. The
Flipper and Laminator tab is shown if
that option is installed only.

Click “Browse” and select the new
firmware
Figure 92 Select Firmware
68
(3) Firmware Update

Click “Update” button to upgrade
automatically, then the printer is
upgraded after rebooting.

In case there are some problems in the
automatic upgrade, you click “Manual
Update” and can see the pop-up widow
as below picture. It shows procedure of
manual upgrade. You can upgrade
manually according to this procedure.
(Caution: Please do not close upgrade
dialog box until it is completed successfully
and do not turn off the printer.)
Figure 93 Update Firmware
69
5. Optional device driver installation
In SMART-51 printer, you can install the optional devices that encode contact smartcard or
contactless smartcard. If your purchased SMART-51 printer has optional devices, you
should also install the smart card reader drivers.
5.1. Contact smartcard reader
In SMART-51 printer, you can install the two types of optional devices which are
contact smartcard reader and mobile SIM smartcard reader. If you have one or more
smartcard reader devices on your printer, you should install the smartcard device
driver as in the following, and connect SMART-51 printer to your PC.
(1) Run the smartcard driver installer
Insert the smartcard installation CD and find “\Options\Gemalto PC Twin” directory
on your CD. Find the right directory which is installed OS version on your PC, and
run the installer. You can see the smartcard reader driver installation window as the
Pic.125. And click “Next”.
Figure 94 Contact smartcard reader driver installation
70
(2) License agreement
The license agreement window is shown. Check at the agreement and click “Next”.
Figure 95 License agreement
(3) Installation
The installation message is shown as the picture. Click “Install” to install driver.
Figure 96 Installing the contact smartcard reader driver
71
(4) Complete installation
When the installation is completed, the window is shown. Click the “Finish” to
complete the installation steps.
Figure 97 Completing the smartcard reader driver installation
72
5.2. Contactless smartcard reader
In SMART-51 printer, you can install the two types of smartcard reader which are
internal contactless smartcard reader and external contactless smartcard reader. If
you have one or more contactless smartcard reader devices on your printer, you
should install the contactless smartcard device driver as in the following, and connect
SMART-51 printer to your PC.
(1) Connect SMART-51 printer to PC
When you connect the printer to PC and turn on the printer, you can see the “Found
New Hardware Wizard” as the picture, then Check “No, not that time” and Click
“Next” to continue.
Figure 98 Found New Hardware Wizard
73
(2) Choose the installation method
At the window as the picture, select “Install from a list or specific location” and click
“Next”.
Figure 99 Installation method selection
(3) Driver location
Insert the smartcard installation CD and find “\Options\ Omnikey 5121” directory on
your CD. Find the right directory which is installed OS version on your PC, and
select the directory as the picture, and click “Next”.
Figure 100 Driver location
74
(4) Complete installation
When the installation is completed, the window as the Pic121 is shown, click “Finish”
to complete the installation steps.
Figure 101 Completing the driver installation
75
6. Troubleshooting
6.1. Error Message
SMART-51 printer shows the error message in the LCD display when it occurs. Click the Left
button to retry or the right button to cancel an operation.
The following shows the error message on your Smart Printer. For checking a status of
printer, please use a CardPrinterTest or CardPrinterDiagnostics in the Utilities folder of
Install CD.
No
LCD Message
Description and Countermeasures
Fail to move a card from the hopper to the printer inside.
-. Check the card thickness and adjust the card thickness control lever
Card In Error
-. Check cards are stuck because of static electricity
-. Clean Hopper roller and cleaning roller
Fail to move a card in the printer.
-. Remove a card if the ribbon is attached
CardMove Int Err
-. Check the rollers and cards, and clean them if they are polluted
-. Check the operating state of the card feeding rollers and sensors
Fail to move a card between printer and other module(flipper/laminator)
CardMove Ext Err
-. Check the rollers and cards, and clean them if they are polluted
-. Check the operating state of the card feeding rollers and sensors
Fail to discharge a card after printing, encoding or laminating.
-. Remove a card if the ribbon is attached
Card Out Error
-. Check the rollers and cards, and clean them if they are polluted
-. Check the operating state of the card feeding rollers and sensors
The Head Up/Down Motor or Sensor don’t work correctly in printing or booting up
TPH UpDown Error
-. Check the operating state of the Head Up/Down Motor and Sensor.
The IC Head Up/Down Motor or Sensor don’t work correctly in printing, encoding
IC UpDown Error
or booting up.
-. Check the state of the Cable between a module and a main board
76
The printer can’t search the ribbon panel in printing or booting up
-. Check the operating state of the Ribbon Motor
Ribbon Seek Err
-. Check the operating state of the ribbon encoder sensor and gears
-. Check and clean the Color In/Out Sensor
-. Check the operating state of the color in/out Sensor
The printer can’t wind the ribbon in printing or booting up.
Ribbon Move Err
-. Check the operating state of the Ribbon Motor
-. Check the operating state of the ribbon encoder sensor and gears
Fail to read or write the magnetic stripe.
-. Check the surface and direction of magnetic card
MAG R/W Error
-. Check the coercivity of magnetic card and encoding configuration
-. Check the rollers, encoder and cards, and clean them if they are polluted
Fail to read a track 1 of the magnetic stripe.
-. Check the surface and direction of magnetic card
10
MAG T1 Error
-. Check the coercivity of magnetic card and encoding configuration
-. Check the rollers, encoder and cards, and clean them if they are polluted
No
LCD Message
Description and Countermeasures
Fail to read a track 2 of the magnetic stripe.
-. Check the surface and direction of magnetic card
11
MAG T2 Error
-. Check the coercivity of magnetic card and encoding configuration
-. Check the rollers, encoder and cards, and clean them if they are polluted
Fail to read a track 3 of the magnetic stripe.
-. Check the surface and direction of magnetic card
12
MAG T3 Error
-. Check the coercivity of magnetic card and encoding configuration
-. Check the rollers, encoder and cards, and clean them if they are polluted
Error occurs while printing
-. Check a card is jammed
13
Printing Error
-. Check usage of a genuine ribbon and cards
-. Check the rollers and cards, and clean them if they are polluted
14
Init Error
Error occurs while initializing
77
-. Check the status of installation of ribbon and laminating film
-. Check the laminator turning on if the laminator is installed
Fail to communicate between a printer and a flipper/laminator
15
DeviceCon Error
-. Check the laminator turning on if the laminator is installed
-. Check a cable between a printer and a flipper/laminator
Error occurs while laminating
16
Lami Error
-. Remove a card after opening a laminator top cover
-. Check usage of a genuine laminating film and cards
Error occurs while operating a flipper
17
Flipper Error
-. Remove a card after opening a flipper cover
-. Check the card size
All ribbons are used
18
Ribbon Zero
-. Install the new ribbon after purchasing it in the place of purchase
Ribbon is not installed or not searched
19
RibbonNotFound
-. Install a ribbon if not
-. Check usage of a genuine ribbon
Thermal Print Head is not installed or not recognized
20
TPH Not Found
-. Check the print head installation
-. Contact the place of purchase
Thermal Print Head is overheated
-. Lower the temperature when the temperature of circumstance is too high
21
TPH Over Heat
-. Take a stop for 10 minutes and print again.
-. Contact the place of purchase if this message is shown regularly
Error occurs when the abnormal printing data is transmitted.
-. Replace the USB cable USB
22
Invalid Data
-. Change the USB port in the PC
-. Reinstall the printer driver
The password is not correct
23
Wrong Password
-. Input the correct password
-. Contact the place of purchase if you forget the password
78
No
LCD Message
Description and Countermeasures
Failed to execute a command of the printer
-. Replace the USB cable USB
24
SetCommandFail
-. Change the USB port in the PC
-. Turn off/on the printer
The printing data is full in the spooler
25
Spool Full
-. This message disappear after printing all data to send
-. Turn off/on the printer if the spool data is full without printing
79
6.2. Cleaning the printer
To maintain the best condition of SMART-51 printer, you must clean the printer
periodically. If you use the exclusive cleaning card as the picture, you can clean the printer
easily. For purchase the exclusive cleaning card, ask to SMART-51 printer provider.
Figure 102 Exclusive cleaning card for SMART-51 printer
If the exclusive cleaning card is ready, click the “Clean Printer” in the service tab of
SMART-51 printer driver. After click, Clean Printer program to clean the printer is run.
Figure 103 Printer cleaning start
80
Step 1. Connect the SMART-51 printer to PC and turn it on, and prepare the exclusive
cleaning card.
Figure 104 Printer cleaning Step 1
Step 2. Open the hopper and top cover and remove the card and ribbon cartridge.
Figure 105 Printer cleaning Step 2
Step 3. Insert the exclusive cleaning card into the printer through input hopper. When the
exclusive cleaning card is inserted to the cleaning roller, it will be move
81
automatically. It is normal that the exclusive cleaning card is inserted to the ends
and rollers are moving to clean.
Figure 106 Printer cleaning Step 3
Step 4. Close the top cover to clean the Thermal Print Head and the printing roller. When
the top cover is closed, cleaning card will be moving back and forth to clean.
Figure 107 Printer cleaning Step 4
82
Step 5. Wait until the cleaning is completed. When the cleaning is completed, the
exclusive cleaning card will be ejected automatically as the picture.
Figure 108 Printer cleaning Step 5
Step 6. Remove the exclusive cleaning card and install ribbon cartridge into the printer.
Figure 109 Printer cleaning Step 6
83
6.3 TPH (Thermal Print Head) replacement
1. Check the serial number and the
resistance of new Thermal Print Head as
the Picture.
TPH type: A = KEE, B = KPE
Serial No.: see the red box.
TPH resistance: see the green box.
Figure 110 Thermal Print Head
2. Set up the new TPH’s configuration using CardPrinterSetup program.
Step1: Run ‘Card Printer Setup’ in Utilities of the installation CD and click expansion
button.
Step2: Click “Change Header” in the extended setup.
Step3: Input the TPH’s Serial No., Resistance and Type (choose KEE or KPE) on the
TPH’s label, and click “OK”.
Step4: Click “Set Config” to set the new TPH’s configuration.
Figure 111 Print head setup
84
3. Replacing the new TPH
Step1: Remove the old TPH from the top cover.
(1) Turn off the printer and open the top cover.
(2) Hold the TPH and press the locked hook, then the TPH is disconnected..
(3) Disconnect the TPH from print head wire carefully.
(Caution: TPH is possible to HOT.)
Step2: Installing the new TPH
(1) Connect new TPH to the print head wire.
(2). Put the new TPH on the Shift and pull it up until be locked..
Figure 112 Print head replacement
4. Setup the print position and the color density.
After installing the new TPH, you must reset the print position and the color density using
CardPrinterSetup utility. Refer to “4.1.2 Default setting”
85
5. Calibration of Print Head Angle
To get the best print quality, the TPH
should be located vertically with card
surface.
If print quality has the problem, it
could be caused by print head angle.
Through Adjusting print head angle
by screw (red mark in the right
picture), you could make good quality
of print.
Figure 113 Print head angle
(Use the appropriate screw driver to
adjust, and turn the screw by 90
degrees at a time.)
6.4. Card movement
6.4.1. Cards can’t enter into the printer from input hopper.

Non-standard cards or bad cards.
Change the cards. You can use only ISO CR-80 card (54mm x 86mm).

Card thickness control lever is set improperly.
Regulate the card thickness control lever to fit the current card thickness.

Bad card array.
Array the cards again and put them on input hopper as section 2.2 in this manual.

Cards have static and moisture.
Remove the moisture or static.
6.4.2. Card Transfer Error occurs when the ribbon is coiled around the transfer
roller or the printing roller.
Open the top cover and remove the card and the coiled ribbon from SMART-51
printer using front LED buttons. If this problem occurred frequently, check the below
things.
 Non-standard cards or bad cards.
Change the cards. You can use only ISO CR-80 card (54mm x 86mm).
 The transfer roller or the printing roller is contaminated with the dust and dirt
Remove the dust and dirt with the cleaning kit as section 6.1
86
 Wrong printing position setting.
Please contact the local supplier
 When operating temperature and humidity is out of the acceptable operating
limit of the printer.
Adjust the operating environment of the printer.
6.4.3. An Error occurs while the card is being transferred.
First of all, check the Error message at LCD display.
Open the top cover and remove the card by LED buttons.
If this problem occurs frequently, check the followings.
 Non-standard cards or bad cards.
Change the cards. You can use only ISO CR-80 card (54mm x 86mm).
 Printer setting is changed or is not proper.
Please contact the local supplier.
 The transfer roller or the printing roller is contaminated with the dust and dirt.
Remove the dust and dirt with the cleaning kit as section 6.1.
 The card surface is contaminated with the dust and dirt.
Check the card surface and remove the dust and dirt and try again. If this problem
occurs again, retry with new card.
6.5. Printing quality
6.5.1. Not printed or wrong colors printed spot.

The card surface is contaminated with the
dust and dirt.
After checking the card, change it to another
card.

The cleaning roller is contaminated with the
dust and dirt.
Check the cleaning roller. If there is much
dust, change the cleaning roller to the new
one.

Figure 114 Printing quality trouble 1
Much dust in the printer.
Clean the inside of the printer with the cleaning kit.
87
6.5.2. Not printed horizontal line.

The ribbon cartridge is installed improperly.
Check the ribbon cartridge installation state
and whether the ribbon has wrinkles.

The printer head is contaminated with the
dust and dirt.
Clean the printer head with cleaning kit.

Figure 115 Printing quality trouble 2
The printer head is damaged.
Please contact the local supplier to replace the printer head.
6.5.3. Unclear or not uniform print.

Uneven or bad card surface.
Change the card.

Too high or low setting of the color density.
Please contact the local supplier. The color
density default of your printer needs to be
changed.

The printer head is contaminated with the
dust and dirt.
Clean the printer head with cleaning kit.
Figure 116 Printing quality trouble 3
6.5.4. Not aligned color print.

Non-standard cards or bad cards.
Change the cards. You can use only ISO CR80 card (54mm x 86mm).

Uneven or bad card surface.
Change the card.

The transfer roller or printing roller is
contaminated with the dust and dirt.
Figure 117 Printing quality trouble 4
Clean the rollers with the cleaning kit as section 6.1.

Worn-out printer.
Please contact the local supplier.
88
6.5.5. Unplanned color print.
 Non-standard cards or bad cards.
Change the cards. You can use only ISO CR-80
card (54mm x 86mm).

Uneven or bad card surface.
Change the card.

The transfer roller or printing roller is
contaminated with the dust and dirt.
Figure 118 Printing quality trouble 5
Clean the rollers with the cleaning kit as section 6.1.
 Worn-out printer.
Please contact the local supplier.
6.6. Magnetic stripe encoding
6.6.1. Magnetic encoding error.
First of all, Please press left LED button to retry.

The magnetic head is contaminated with the dust and dirt.
Clean the magnetic head with the cleaning kit.

The magnetic encoding data is not transmitted or the wrong data is
transmitted.
Check the setting of the program and the driver and the magnetic encoding data you
transmitted.

The card is not magnetic card, or inserting direction is wrong.
Change the card or the direction.

Bad magnetic stripes on the card.
Change the card.
89
6.7. General operation
6.7.1. Ribbon snapped during printing.
Open the top cover and take out the cartridge. After putting the snapped pieces on
together, install the cartridge again. Check the followings if this kind of problem occur
frequently.

Non-standard cards or bad cards.
Change the cards. You can use only ISO CR-80 card (54mm x 86mm).

Too high or low setting of the color density.
Please contact the local supplier. The color density default of your printer needs to
be changed.
6.7.2. LCD display “Ribbon Not Found”
Press the left LED button to retry. If it occurs frequently, check the followings.

Not genuine ribbon.
Change to the genuine ribbon.

Ribbon is consumed.
Printing is not possible if ribbon is used up. Change the ribbon.

Snapped ribbon.
Open the top cover and take out the cartridge. After putting the snapped pieces on
together, install the cartridge again.
6.7.3. Printer doesn’t operate even if the printing data has been transmitted.
Check the following.
 Printer power off.
Check the power. Turn on the printer power.
Check the printer adaptor whether it is connected with a socket and the printer.
 Bad power adaptor.
Please contact the local supplier for replacement of the adaptor.
 The printer driver is “Offline”.
Change the printer driver to “Online”.
 The printer’s USB cable is disconnected or the connection is bad.
Check the cable’s connection between PC and the printer.
If not good, make the USB cable connection again.
90
 Bad USB cable.
Change the USB cable.
 The printing is operated with another printer driver.
Select the correct SMART-51 printer driver again.
 Wrong USB port setting of the printer driver.
Check the port setting of the printer driver and change the port setting.
 No ribbon in the printer or error occurred.
Install ribbon in the printer or resolve the error.
 Too long power or USB cable (more than 1.5M).
Use the cable provided with the printer.
 PC’s USB port is down:
Reboot your PC.
91
7. Specification
Model
Printing
SMART-51S
Print Type
Dye-Sublimation
Print Area
Edge to Edge
Resolution
300dpi
Dual Side Printing
Card
SMART-51D
Option (with Flipper)
Card Feeding
Card Size
Yes
ISO CR80 or ISO CR79 (option-Factory installed)
0.38mm (15mil), 1.0mm (40mil)
Card Type
PVC, PET, Composite PVC
Monochrome
5 sec./card (720 cards/hour)
YMCKO
Laminating
Yes
Automatic
Card Thickness
Printing Speed
SMART-51L
Max. 17 sec./card (212 cards/hour)
YMCKOK
Max. 22 sec./card (164 cards/hour)
Mode
Single & Dual
Film
0.6mil, 1.0mil
Simultaneous
22 sec./card (YMCK)
(Single)
32 sec./card (YMCKK)
One by One
43 sec./card (YMCK)
(Single)
53 sec./card (YMCKK)
Speed
Capacity
Input Hopper
Output Hopper
System
100 Cards / 200 Cards with cover open
Front : 40 Cards / Rear : 100 Cards (Optional Rear-side Stacker)
Memory
64MB RAM
Display
2 Line LCD
Control Panel
2 LED Buttons
Supported Platforms
MS Windows 7/ 8/ 10, Mac OS, Linux
Communication
USB, Ethernet (Option)
Power Supply
Power Consumption
DC 24V, 2A
48
Temp. / Humidity
Dimensions
48
96
15~35℃ / 35~70%
Millimeter (WxLxH)
165 x 390 x 210
165 x 498 x 210
165 x 675 x 210
Inch (WxLxH)
6.5 x 15.4 x 8.3
6.5 x 19.6 x 8.3
6.5 x 26.6 x 8.3
5.2 / 11.5
8.8 / 19.4
Weight
Kg / Lbs
4.5 / 10
Encoding Options
Magnetic
ISO 7811 (Track I, II, III Read/ Write, HiCo/ LoCo), JIS II
Contact
Contactless
ISO 7816 (ID-1)
MIFARE, ISO 14443 (Type A/ B), ISO 15693, DESFIRE, iCLASS
Certifications
CB, CE, FCC, KC, CCC
Specifications and availability may change without notice.
92

RFID(13.56MHz) Usage
The RFID Tag is used for the security and the recognition of the ribbon. To get the
optimized printing quality on the printed card, the genuine ribbon of IDP should be used
to print cards by using SMART printer. SMART printer can recognize the genuine ribbon
by reading the encoded information on the RFID Tag of the ribbons. To support user’s
various requirements for printing cards appropriately, many kinds of ribbons should be
provided and SMART printer should distinguish the type of installed ribbon. To
distinguish the installed ribbon type correctly, SMART printer reads the encoded
information on the RFID Tag of the ribbons. According to the installed ribbon type and
the ribbon supplier, the printer driver of SMART printer can select the color profile and
create the printing data.
93

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2017:07:25 11:50:31+09:00
Modify Date                     : 2017:07:25 11:50:48+09:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2017:07:25 11:50:48+09:00
Creator Tool                    :  Word용 Acrobat PDFMaker 15
Document ID                     : uuid:65807752-8473-48e8-a3b5-551d4dee1685
Instance ID                     : uuid:172a1677-dc33-4b94-8e50-6ff8be35e55f
Subject                         : 5
Format                          : application/pdf
Title                           : 목차
Creator                         : Administrator
Producer                        : Adobe PDF Library 15.0
Source Modified                 : D:20170725011948
Company                         : 꿈나라사탕공장
Page Layout                     : OneColumn
Page Count                      : 93

EXIF Metadata provided by EXIF.tools