IDT Technology RP107R Bicycle Computer (Receiver) User Manual 1e 13 6
IDT Technology Limited Bicycle Computer (Receiver) 1e 13 6
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 486674 |
| Application ID | OhtGqvuvEcHZiDaYjp4rkw== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 243.34kB (3041793 bits) |
| Date Submitted | 2004-11-08 00:00:00 |
| Date Available | 2004-11-08 00:00:00 |
| Creation Date | 2003-05-24 11:08:24 |
| Producing Software | Acrobat Distiller 4.0.5 for Macintosh |
| Document Lastmod | 2004-10-12 16:11:21 |
| Document Title | 1e-13/6 |
| Document Creator | Adobe PageMaker 6.52 |
| Document Author: | LCD8600 |
CLOCK Mode .................................................................... 9 Set clock and measurement units ................................. 9 Set the alarm ................................................................. 9 Stopwatch ......................................................................... 9 Timer ................................................................................. 10 Temperature display ........................................................ 10 ALTI-BARO Mode ............................................................. 10 Access altimeter options ................................................ 11 Set current altitude and resolution ................................. 11 Set sea-level pressure ................................................... 12 View sea-level pressure ................................................ 12 Set altitude alert ............................................................. 12 Recall altitude data ........................................................ 13 Switch between view options ......................................... 13 Weather forecast ........................................................... 13 TOUR Mode ...................................................................... 14 TOUR memory .............................................................. 14 Activate TOUR Mode ..................................................... 15 Record markers in TOUR Mode .................................... 15 Pause TOUR Mode ....................................................... 15 Deactivate TOUR Mode ................................................ 15 Clear all TOUR memories ............................................. 16 CARDIO (Heart Rate) Mode (RS107, RP107 only) ......... 16 Wearing the chest belt ................................................... 17 Training Zones ............................................................... 17 Set upper and lower heart rate limits for Training Zone 5 ............................................................. 18 Activate the Training Zone alarm ................................... 19 Track heart rate during training ..................................... 19 Oregon Scientific™ OUTBREAKER Sports Watch (RX107 series) User Manual TABLE OF CONTENTS Introduction ...................................................................... 2 Key features ..................................................................... 3 OUTBREAKER watch ................................................... 3 Chest belt (RS107 / RP107 only) .................................. 3 Bicycle equipment (RP107 only) ................................... 3 PC Kit (RP107 only) ..................................................... 4 LCD display symbols ..................................................... 4 How the OUTBREAKER works ....................................... 6 How the altimeter, thermometer and barometer work ... 6 A multi-system facility .................................................... 6 TOUR Mode .................................................................. 6 PC Software Kit (RP107 only) ....................................... 6 Getting started ................................................................. 7 Turn on the watch (first-time use only) .......................... 7 Batteries ........................................................................ 7 Switch between Modes .................................................. 8 Switch between Mode options ....................................... 8 Change setting values ................................................... 8 Use the HI-GLO backlight .............................................. 8 Key lock ......................................................................... 8 Handling the product ..................................................... 8 E BIKE Mode (RP107 only) ................................................. 20 Set up for BIKE Mode .................................................... 20 Step 1: Attach the equipment to the bicycle .................. 20 Step2: Enter wheel circumference ................................ 21 Access the BIKE Mode options ..................................... 22 View speed and cadence information ............................ 22 PC Kit (RP107 only) ......................................................... 22 PC Mode ............................................................................ 23 Set up for PC Mode ....................................................... 23 Use the software ............................................................ 23 PC Mode options ........................................................... 23 Download data ............................................................... 24 Effective use and range ................................................... 24 Aquatic and outdoor activities ........................................ 24 Safety and care ................................................................ 25 Safety precautions ......................................................... 25 Care instructions ............................................................ 25 Troubleshooting guide .................................................... 26 Specifications ................................................................... 27 Warnings ........................................................................... 29 Additional Resources ...................................................... 29 INTRODUCTION Thank you for selecting the Oregon Scientific OUTBREAKER Sports Watch as your fitness product of choice. Your new sports watch is designed to give you many years of reliable service and includes the following features: • Clock, calendar, stopwatch and timer functions • Barometer with local and sea pressure readings • Weather forecast and temperature readings • Altimeter readings up to 30,000 feet (9,000 meters) • Heart rate monitor that gives pulse rate readings during exercise (RS107/RP107 only) • Bicycle accessory kit to take readings during cycling (RP107 only) • PC docking station and software to download readings onto your computer (RP107 only) The OUTBREAKER RX107 sports watch series comprises the most advanced and patented Baro-compensation technology, distinguishing between barometric and altitude pressure changes, and giving you more reliable readings (weather forecasts, etc.). It is a precision device designed to augment your daily or weekly exercise program as well as provide you with accurate and easy to use watch functions. Note on compliance ......................................................... 30 This manual contains important safety and care information, and provides step-by-step instructions for using this product. Read the manual thoroughly, and keep it in a safe place in case you need to later refer to it. E BICYCLE EQUIPMENT (RP107 ONLY) KEY FEATURES OUTBREAKER WATCH I ITEM NAME SELECT/+/> MODE ST/SP/- LIGHT/KEY FUNC/SET DESCRIPTION Press to increase value, change Mode display, or record a marker during TOUR Mode. Press to switch between Modes. Press to start/pause/stop the Stopwatch/Timer or decrease value. Press to activate HIGLO- backlight, or press and hold to activate key lock. Press to enter a sub-mode or press and hold to change a value.. ITEM CHEST BELT I ITEM NAME CHEST BELT STRAP NAME SPEED SENSOR CADENCE SENSOR BIKE MOUNT MAGNETS/ SCREWS/ NUTS/PADS FIXING STRAPS RUBBER GRIPS (RS107 only) E LCD DISPLAY SYMBOLS PC KIT (RP107 ONLY) SYMBOL YR ITEM DOCKING STATION WATCH CONNECTION POINTS MOUNTING CLIPS BUILT-IN RS-232C COMPUTER CONNECTION CABLE SOFTWARE CD-ROM Month setting. DAY Day setting. Current day of the week. TRIP TOUR Mode is running time/date cannot be set HR Hour setting. MIN Minute setting. DM/MD Year setting. MTH MON (MON..SUN) NAME DESCRIPTION The current time. Order for date to be displayed. TIME Time zone setting screen. SET Displayed when in a setting mode. UNIT Set Celsius/Fahrenheit for temperature and h/p/Hg, inHg barometric pressure. Set m/ft for altitude. E Zone AL The current time set in your second time zone. Sxxx Speed sensor low battery. Shows alarm time, or event alarms (max/min altitude/heart rate etc) Cxxx Cadence sensor low battery. ttl Shows max/min altitude alarm is deactivated. Shows if alarm is on or off. Heart rate (per minute) monitor activated. Weather forecast for the next 12-24 hours. (Sunny/Slightly Cloudy/Cloudy/Rainy) STW Stopwatch can be started/stopped/reset. TMR Timer (countdown) can be started/stopped/reset TEMP Temperature is displayed (in lower second row). ALTI Altitude is displayed (in lower second row). HR Heart rate is displayed in lower matrix font. MEM Memory record (current trip only). max Shows maximum record min Shows minimum record AVG Shows average record TTL Show total record RES Change resolution of readings on altimeter ICON Choose current weather icon. LOC Local barometric pressure. SEA Sea pressure (barometric). SPD Shows vertical speed (historical or current). Rxxx Receiver (Bike Mount) low battery. Shows total time of activity. Shows altitude graphically. Heart rate alert in effect. Key lock activated. Z1 (1-5) Shows which training shown is currently selected. Shows heart beat graphically. M1 (1..99) Shows which record you are making, or storing (see TOUR Mode). WØ (wheel icon) Wheel circumference setting mode. CAD T1 (1…99) Pedal speed (revolutions/min). Shows sequence of memories in TOUR Mode. 88% % of memory used in TOUR Mode. END TOUR is finished. CLR Ready to clear all tour memories. donE All tour memories have been cleared. hpa Pressure shown in Hecto-Pascal’s. inHg Pressure shown in inches of mercury. Low battery level (replace batteries) Graphical display of your bicycle speed. E use the stopwatch or timer (countdown) facility in combination with other functions, and both will continue to run in the background while you use other features of the watch. HOW THE OUTBREAKER WORKS The OUTBREAKER sports watch comes equipped with a barometer (measuring altitude, barometric pressure, and weather conditions), a weather forecast display, a thermometer, a heart rate monitor (RS107/RP107 only), and a bicycle computer to display information when cycling (RP107 only). The heart-rate monitor and altimeter features of the OUTBREAKER watch include customized settings. Maximum and minimum heart rate limits can be set for use during exercise, and the altimeter can be set to register ascending and descending limits. In both cases a short beep signifies either limit has been exceeded. The watch also has a clock, calendar, and pressure reading apparatus, all of which need to be set according to the current date and location. HOW THE ALTIMETER, THERMOMETER, AND BAROMETER WORK The patented baro-compensation technology used in this watch allows it to distinguish between barometric pressure change and altitude pressure change. This means it can detect barometric pressure (localized weather conditions) as distinct from changes in altitude pressure, and gives more accurate readings than most average devices (which frequently rely on manual deactivation before initiating a new forecast). TOUR MODE The watch features a TOUR Mode in which you can record all data from a single trip, or workout, and then download this information onto your PC for storage and viewing. The watch can recall 99 different single tours, trips or workouts. NOTE The docking station and CD-ROM are required (optional for the RA107 and RS107, but not supplied) to download information from TOUR Mode. A MULTI-SYSTEM FACILITY The product is designed for use during many kinds of activity. It can display and store a range of information of interest to the casual and more serious sports or exercise enthusiast. The watch includes the following Modes: CLOCK, ALTIMETER, CARDIO (Heart Rate) (RS107/RP107 only), BIKE (RP107 only), and PC (docking station and CDROM are optional for the RA107 and RS107, and are not supplied). It is equipped with a multi-system facility that allows you to combine information according to your preference, such as altitude and time, altitude and heart rate, or bike speed and altitude, etc. You may also PC SOFTWARE KIT (RP107 ONLY) A docking station is provided with the watch for connecting to a computer, along with a CD-ROM for installing the necessary software onto your computer. You can also use the software to change some of the watch settings. NOTE The RZ910 PC Kit can be purchased separately for the RA107 and RS107. E To load new batteries in the chest belt (RS107 and RP107 only) and bike mount: GETTING STARTED NOTE The chest belt will stop sending signals if its battery is low. Bad transmission from the chest belt may also be the result of poor contact with the skin, surrounding interference, or placing the receiver watch too far away. TURN ON THE WATCH (FIRST-TIME USE ONLY) Press mode key for 2 seconds or more to activate the LCD Display Diagram BATTERIES All batteries are included and already installed. Refer to the Specifications page for battery types (➔ 27). NOTE To avoid the possibility of permanently damaging the watch, we strongly recommend that you take your watch to a local retailer or jeweler to have the watch battery replaced. Instructions 1. Insert a coin into the grove. Turn counter-clockwise. 2. Insert the battery. Match the correct polarity. 3. Replace the battery compartment. Tighten into place. To load new batteries in the watch: Diagram Instructions 1. Remove the watchband and screw pin. To load new batteries in the bicycle sensors (RP107 0nly): NOTE The sensors will stop sending signals to the watch if their batteries are low. 2. Remove the back cover with a small Phillips screwdriver. CR 20 3 2 Diagram 3. Install the battery by matching the correct polarity. Always use the correct battery type. Warning: Reversing the polarity may damage the product. 4. Replace the cover, screws, screw pin, and watchband. (Be sure to replace the O ring properly). 5. Check the replacement batteries are fitted properly by confirming there is a key tone (beep). Instructions 1. Insert a coin into the grove. Turn counter-clockwise. 2. Remove the battery and insert a new one. 3. Replace the compartment. Tighten into place. NOTE Replace the batteries whenever the HIGLO backlight dims or stops working, or when you see the low battery icon. E The watch will show Cxxx, Rxxx or Sxxx whenever either the bike mount, cadence or speed sensor batteries are low. USE THE HI-GLO BACKLIGHT Press light/key to turn on the HI-GLO backlight on for five seconds. Once the light is on, press any key to keep it on for a further five seconds. NOTE Replace all the batteries at the same time – it is dangerous to mix old and new batteries. NOTE Used batteries can be harmful to the environment, and should not be thrown out with household rubbish. Contact your local waste disposal authority for instructions on how to dispose of used batteries. Protect the environment by taking exhausted batteries to authorized disposal stations. In order to save power the light will not work when the battery is low. If this happens, change the battery as soon as possible. KEY LOCK The watch also has a key lock function to stop the buttons from being accidentally pressed during an activity. To activate it simply press and hold light/key until a small key icon appears in the right hand corner of the screen. The function keys are now useless. To reactivate them, press and hold light/key again until the key icon disappears. SWITCH BETWEEN MODES Press the MODE button to switch between the Modes: CLOCK, ALTI-BARO, CARDIO (RS107/RP107 only), BIKE (RP107 only), and PC. A bar shows next to the appropriate Mode (on the outer ring of the LCD display) when it is selected. NOTE The alarm will still go off while the Key Lock is activated. Pressing any key while in Key lock will stop the alarm. SWITCH BETWEEN MODE OPTIONS HANDLING THE PRODUCT Press SELECT/+ to switch between the options within a Mode. The watch is designed to withstand a wide range of sports activities, and comes complete with a strong wristband. When riding (RP107 only), make sure the watch is firmly connected to the bike mount, and connect all bicycle equipment carefully and securely. See the BIKE Mode section (➔ 20) for instructions. CHANGE SETTING VALUES Press and hold FUNC/SET for 2 seconds to enter setting mode. Then, press ST/SP/- or SELECT/+ to change the value. Press FUNC/SET to switch between options, and to confirm the changes when you are done. E SET THE ALARM CLOCK MODE Diagram The time, date (including the day of the week) and time alarm can be set while the watch is in CLOCK Mode. Follow the instructions below to set or activate the time, date, zone time, metric or imperial standards, alarm time, stopwatch and timer. Instructions 1. Press MODE to display the CLOCK mode. 2. Press SELECT/+ 3 times to move it into the alarm setting screen. SET CLOCK AND MEASUREMENT UNITS: Diagram 3. Press ST/SP/- to activate or deactivate the alarm. A small bell icon will appear on the left side of the alarm time when it is activated. 4. Press and hold FUNC/SET for 2 seconds, to set the alarm hour and minutes. Use the SELECT/+ or ST/ SP/- buttons to change the value. (The alarm will be automatically activated once the alarm time is set). Instructions 1.Press MODE to display the CLOCK mode. 2.Press and hold FUNC/SET for 2 seconds. “24h” will flash on the display. 3.Press ST/SP/- to change from 24 hour to 12 hour time display. 4.Press FUNC/SET again. The hour will flash. Press SELECT/+ to move the value up, or ST/SP/- to move the value down. Tip: Continuously press and hold a button to fast-change the value. 5.Repeat Steps 3 – 4 to change the rest of the settings, in this order: minutes, year, month/date or date/month display, month, day, time zone (+/- 23 hours), temperature display (°C / °F), measurement units (feet / meters), and barometric pressure units (inHg or hPa). NOTE You cannot change these settings while in TOUR Mode. If you attempt to do so, TRIP will show on the display. Refer to the TOUR Mode section (➔ 14). STOPWATCH The Stopwatch works in CLOCK, ALTI-BARO, CARDIO, and BIKE modes. From any of these modes, press SELECT/+ to display the stopwatch. Then, • Press ST/SP/- to start, pause, and stop the stopwatch. • With the stopwatch stopped, press and hold FUNC/SET to reset. NOTE You can switch to other modes while running the stopwatch in the background. E TIMER TEMPERATURE DISPLAY The Timer works in CLOCK, ALTI-BARO, CARDIO, and BIKE modes. From any of these Modes, press SELECT/+ to display the stopwatch. Press FUNC/SET to reset the Stopwatch, then: The Temperature can be displayed in CLOCK, ALTI-BARO, CARDIO, and BIKE Modes. From any of these Modes, press SELECT/+ to display the Temperature. The Temperature shows in either Celsius or Fahrenheit, depending on the measurement unit you select when setting the CLOCK (see CLOCK Mode). • Press and hold FUNC/SET for 2 seconds. The display will change to TMR. NOTE Your wrist temperature may affect the reading, particularly during exercise. Take off the watch and leave it for 15 minutes to get the most accurate reading. • Press ST/SP/- or SELECT/+ to change a value. • Press FUNC/SET to switch between values and accept changes. • Press ST/SP/- to start or stop the timer. ALTI-BARO MODE • With the timer stopped, press and hold FUNC/SET to reset. NOTE You can switch to other Modes while running the timer in the background. The OUTBREAKER sports watch includes a barometer that distinguishes between pressure caused by altitude changes and pressure caused by weather conditions. This technology reduces discrepancies in readings and makes the altimeter more accurate than most average devices. NOTE To return to STW Mode, you must reset all the timer values to 0. The timer automatically switches to STW Mode when it reaches 0. The watch can store and recall the following values: • Current altitude (updated every 2 seconds) • Maximum / minimum altitudes attained during your a trip • Total accumulated maximum / minimum altitudes attained during your trip 10 E • Maximum / minimum altitude alert (sounds an alarm when exceeded) SET CURRENT ALTITUDE AND RESOLUTION When you first use the watch, it is important to set the current altitude and local sea-level pressure so your ascending and descending altitude can be accurately measured. You can find the current altitude by comparing your position to a topographical map, and then entering the value in the watch. NOTE It is necessary to reset the altitude after being in a pressurized chamber (such as an airplane). For instructions on setting the sea-level pressure, refer to the next section. • Maximum / ascending, maximum descending speeds • Current vertical speed • Rate of altitude change The altitude is shown it two ways, as a numeric value indicating your current altitude, and as a bar chart indicating changes in altitude. Both values will change as you move about. Diagram NOTE In ALTI-BARO Mode, the current altitude is always displayed in larger font, in every screen except the sea pressuresetting screen. Instructions 1. Press and hold FUNC/SET for 2 seconds while in ALT mode. ACCESSING THE ALTIMETER OPTIONS 2. Use SELECT/+ or ST/SP/- to change the value. The value will change in unit increments based on the resolution you set (next step) and the measurement unit you selected when setting the CLOCK (➔ 9). 3. Press FUNC/SET to switch to the Resolution setting screen, then press ST/SP/- to change the value. The resolution is the increment at which the altitude will display: 3 / 10 ft, or 1 / 3 meters. 4. Press FUNC/SET to exit the setting mode. Tip: You can also set the current altitude and alarm limits with the help of the PC software (see PC section). (RP107 only) NOTE The sea level pressure reading will change if the altitude is adjusted. Press MODE to access the ALTI-BARO mode, then press SELECT/+ to loop through the options. 11 E SET THE SEA-LEVEL PRESSURE SET ALTITUDE ALERT Sea level pressure can change relative to location. To achieve accurate altitude readings, set the sea-level pressure value before every trip. Check the newspaper, local news station, trail marker, or weather forecast for local readings, and always select the reading nearest to your present location. The watch can be set to remember an altitude limit (either up or down, but not both simultaneously). If the alarm is activated, a series of beeps (at 5 second intervals) will sound, and the mode bar will blink, when you breach the limit. To end the alert, press any button. Diagram To set the alert limits and activate or deactivate the alert: Instructions 1. While in ALTI-BARO Mode, press SELECT/+ until the SEA (sea pressure) screen is shown. Diagram 2. Press and hold FUNC/SET for two seconds, then use SELECT/+ or ST/SP/- to change the value. The value will change in increments of 1 hPa or .03 inHg, depending on the measurement unit you selected in CLOCK Mode (see CLOCK mode). 3. Press FUNC/SET again when finished. Instructions 1. Press SELECT/+ until you reach the Alarm screen. (Display reads 'AL' or 'NoAL' at the bottom) 2. Press and hold FUNC/SET for two seconds. NOTE The altitude reading will change according to the sea level pressure adjustment. 3. You may set the arrow at the bottom of the screen to a ascending, or descending limit (but not both). To change direction, press SELECT/+ or ST/SP/-. 4. Press FUNC/SET again, then press SELECT/+ or ST/SP/- to change the altitude limit. (The alarm will be automatically activated once the limits are set). 5. Alternatively press ST/SP/- if you simply want to accept a preset altitude alert setting. (Activated [AL] or deactivated [NoAL]). VIEW THE SEA-LEVEL PRESSURE To view a graphical image of the current sea level pressure reading, press FUNC/SET with the SEA screen shown in ALTI-BARO Mode. Press again to return to normal display. 12 E RECALLING ALTITUDE DATA SWITCH BETWEEN VIEW OPTIONS The OUTBREAKER allows you to track the following information as you exercise. While in ALT/TIME Mode, press FUNC/SET to switch between the view options: max / min altitude, total ascending / descending altitude, and speed. In the speed display, you can view current speed (ascending or descending), maximum ascending speed, and maximum descending speed. • Max / min altitude attained -- shows the highest or lowest point you have reached so far in relation to your watch’s permanent altitude setting. • Max / min altitude accumulated – represents the total distance you have ascended or descended; that is, every incline is added together or ‘accumulated’, and likewise every decline is added and ‘accumulated’, to give a total. Press SELECT/+ or ST/SP/- to loop through the values for each option. • Vertical speed -- how fast you are currently climbing • Max ascending speed – fastest speed you have climbed To clear a value from the memory, press and hold FUNC/SET for 2 seconds. • Max descending speed – fastest speed you have descended The following illustration shows these points: FUNC./SET WEATHER FORECAST These display screens are shown in a loop, and the information in each screen is displayed for 30 seconds (excluding the ALT/SPD vertical speed screen, which is not on a timeout) at which point the watch returns to ALT Mode. ST/SP/- SEC/+ FUNC./SET ST/SP/- SEC/+ FUNC./SET The built-in barometer helps to forecast the weather for the next 12-24 hours. This reading is based on barometric pressure changes and has an effective range of 30 to 50 kilometers (18 – 31 miles). The patented baro-compensation technology in the OUTBREAKER watch allows it to differentiate between pressure changes due to altitude, and those due to weather changes. To avoid inaccurate forecasts, the watch will favor altitude readings when you are actually ascending or descending. This means the weather icon will disappear after significant vertical movements. To display an accurate forecast, simply remain at any fixed altitude for roughly 5 minutes. ST/SP/- SEC/+ SEC/+ ST/SP/- NOTE Clearing the memory allows you to start over again on a new trip, though all the information from your current trip will be lost. You may wish to set the icon manually for these reasons: • The speed in the change of icon forecast depends on the 13 E speed of barometric change and in some cases may take longer (up to 24hrs) than desired. TOUR MODE There are two ways of using the memory on the OUTBREAKER. First, the watch computer will record information as you train, for display only. This means you can check the information during or after your exercise, but there will be no record once you clear the memory in preparation for your next training event. • Setting the icon can speed up the adjustment for the weather forecast. • It is necessary to set the icon after exposure to artificial environments, such as an airplane cabin, which may cause incorrect readings. The forecast will be displayed at the top of the watch as one of these four icons: To record and store this information (for up to 99 different trips, depending on the size of each record – see below) you must activate the TOUR Mode and view the records through the PC software. NOTE The information from a TOUR can only be viewed through the PC software. The current barometric pressure reading (in hPa or inHg, depending on the measurement unit you set in CLOCK Mode) shows at the bottom of the display. TOUR MEMORY Tour mode allows you to record and store data displayed on the watch, which can then be downloaded onto your PC. Up to 99 TOURs can be recorded and stored to the PC software. Depending on the model you purchase, the information you choose to record (see below), and the time used by TOURs you have already stored on the watch, the available memory length may vary. The average memory storage capacities in realtime, (taking a data sample every 5 seconds), assuming default settings (see Specifications: Tour Mode) and no TOURs have been saved for each model are as follows: To set the weather icon manually, follow these instructions: Diagram Instructions 1. While in the ALTI-BARO Mode, press SELECT/+ until LOC shows at the bottom of the display. 2. Press and hold FUNC/SET for two seconds. 3. Press SELECT/+ or ST/SP/- to change the icon. 4. Press FUNC/SET to save your changes. Model RA107 RS107 RP107 NOTE When functioning normally the watch automatically updates the forecast every 15 minutes. 14 Total recording time available 598 min (10 hours) 508 min (8.5 hours) 659 min (11 hours) E The watch can record and store up to 99 different trips, providing there is enough remaining memory. RECORD MARKERS IN TOUR MODE The marker function is used to mark a particular position during a TOUR. To place a marker, press and hold SELECT/+ when the TOUR Mode is in use. Default sampling time for readings in TOUR Mode is every 5 seconds. To increase the gap between samplings, and thus increase the memory capacity, you can adjust this setting through the PC software. NOTE The marker will only be shown in the PC data, once it has been downloaded from the watch. ACTIVATE TOUR MODE: PAUSE TOUR MODE: For best results, perform these steps immediately before you begin your trip. 1. Simultaneously press FUNC/ SET and MODE. The TOUR END screen will display. 2. Press and hold FUNC/SET for two seconds. The TOUR number (T1, T2, etc.) will show at the bottom of the display. You are now recording information. The percentage (%) at the top indicates the total used memory. 3. To stop the TOUR, press and hold FUNC/SET for 2 seconds. END will show at the bottom of the display. The Tour data will be stopped. 4. To begin another TOUR, press and hold FUNC/SET for 2 seconds. The new TOUR number (T3, etc.) will show at the bottom of the display. You are recording information again. 5. Press MODE to return to the CLOCK display. NOTE Used watch memory is given as a percentage. It is recommended that you download information to your PC and clear all TOUR memories when this figure approaches 100%. When the used memory hits 100% it will no longer record, and any future readings will not be recorded. 1. If you are not already in TOUR Mode, simultaneously press FUNC/SET and MODE. The TOUR number will display. The percentage (%) at the top indicates the total used memory. 2. Press FUNC/SET. REST shows at the bottom of the display. 3. Press ST/SP/- to turn the rest on (paused) or off (recording). DEACTIVATE TOUR MODE: For best results, perform these steps immediately after you end your trip. 2 sec 1. Simultaneously press FUNC/SET and MODE. The TOUR number will display. The percentage (%) at the top indicates the total used memory. 15 E 2. Press and hold FUNC/SET for two seconds. This ENDS the TOUR recording session. CARDIO (HEART RATE) MODE (RS107/RP107 ONLY) 3. Press MODE to return to the CLOCK display. The OUTBREAKER watch is equipped with a CARDIO Mode and heart rate chest belt, which together allow you to measure your heart rate (from 25-240 beats per minute) while exercising. You can track your heart rate while in the ALTI-BARO, CARDIO, or BIKE Modes, and with the following features: Stopwatch, Timer, Temperature, and Altimeter display. CLEAR ALL TOUR MEMORIES For best results, perform these steps after you download TOUR information to the PC software. Either: 1. Download the information to you PC (the TOUR will be automatically cleared. Or: There are five screens in the CARDIO Mode including the HEART RATE/CLOCK/HR chart (starting) screen. They are: 1. Deactivate the TOUR Mode. With the END screen shown, press the FUNC/SET button. CLR shows at the bottom of the display. • HEART RATE/CLOCK/HR chart (starting) screen, • 2. Press and hold FUNC/ SET until donE shows at the bottom of the display. HEART RATE/HR alarm on/off/ screen, • 3. Press FUNC/SET again to display 0% and confirm all data has been cleared. HEART RATE/STW (stopwatch) screen, • HEART RATE/TEMP (temperature) screen, • HEART RATE/ALTI (altimeter) screen. 4. Press MODE to return to the CLOCK display. NOTE The maximum and minimum values for the various submodes (i.e., max heart rate, or max altitude, etc) will remain after all data has been cleared. To move between them, simply press SELECT/+. 16 E will begin Once you have good contact with the chest belt, to flash. This means the signal is being sent and your heart rate will soon appear in place of the large 0. Your heart rate will be displayed as the larger font in every screen of this Mode, and can also be displayed in a smaller font, below the line, while in BIKE Mode. If you remove the chest belt, or the watch is moved too far away from it, the signal will be broken. NOTE The CARDIO Mode will stop functioning after no signal is received for 5 or more minutes. WEARING THE CHEST BELT You must wear the chest belt to measure your heart rate. NOTE This OUTBREAKER watch is specially designed to work with the chest belt with which it was sold. It is not recommended you use any other chest belt with this watch, as the transmission may not work. Diagram Instructions 1. Wet the conductive pads on the underside of the chest belt with few drops of water or a conductive gel to ensure a better, solid contact. 2. Put on the belt, wrapping it around the upper chest so the heart rate monitor is in the middle of the chest, tucked snugly under the pectoral muscles. 3. Adjust the belt for comfort and best contact with the skin. NOTE When you are measuring your heart rate, keep the watch away from signal generating sources, such as TVs, PCs, and car engines, as these may impair the reading. TRAINING ZONES The OUTBREAKER watch is equipped with a special Training Zone feature that allows you to pre-select the optimal heart rate range (50-240 beats per minute) for your activity. For example, the amount of exertion required for a stroll in the park is different from the amount of exertion required for weight lifting to build muscle mass. With the Training Zone feature, you can set and then monitor the upper and lower heart rate limits (Training Zone) that best support your training activity and goals. Tips: The transmission from the belt is dependent on good contact with the skin and proximity to the receiver watch. Make sure the transmitting section of the belt is against the skin, not blocked by chest hair, and close enough to the receiver watch (approximately 30 inches) to send a clear signal. Sweat or gel can help to improve the signal, and remember it is not instantaneous. If no signal is received immediately, wait for a few seconds for the signal to get through. NOTE An old battery may weaken the transmission and reception power. Replace the battery if the performance is progressively worse. 17 E The calculation for determining your upper and lower heart rate limits is as follows. Maximum Heart Lower limit Upper limit Range (MHR) Men 220 – age = MHR MHR x (lower training zone %) MHR x (upper training zone %) Women 230 – age = MHR Once you know your maximum heart range, you can set the 5 Training Zones (described below) with the PC software (refer to the online help). With the OUTBREAKER watch, you can directly set your upper and lower limits for Training Zone 5, and can set an alarm to sound whenever you exceed the limits for the selected Training Zone. 80 – 90% 90 – 100% Sex NOTE High-altitude activities may elevate your maximum heart rate. NOTE You can override the zone preference by adjusting the value through the PC (all zones), or by manually adjusting Zone 5. Warning: The heart rate limits for Training Zones 1 – 4 are based on the profile for a 20-year-old young man. If you do not meet this profile, we HIGHLY RECOMMEND that you either set the limits for Training Zones 1 – 4 using the PC software, or follow the steps below to set the limits for Training Zone 5. SET UPPER AND LOWER HEART RATE LIMITS FOR TRAINING ZONE 5 1. Press MODE to access the CARDIO (heart rate) Mode. The recommended Training Zones are as follows: Zone Anaerobic Zone – Generates speed and power. It works at or above the body’s oxygen intake capability, builds muscle, and cannot be maintained for a long period of time. Red Line Zone – This high-intensity zone can only be maintained in short bursts or intervals, as it pushes your muscles and cardiovascular system beyond their capacity. 2. Press SELECT/+ to switch to the AL (Alarm) setting. MHR range Description (min – max %) 50 – 60% Moderate Activity – This low-intensity zone is good for warmups, cool downs, and activities such as brisk walking. It is also good for beginners and those who want to strengthen their cardiovascular systems. 60 – 70% Weight Management – Up to 85% of calories burned in this zone are from fat cells. Moderate exercises such as light jogging or swimming are good for this zone. 70 – 80% Aerobic Zone – Increases strength and endurance. It works within the body’s oxygen intake capability, burns more calories, and can be maintained for a long period of time. 3. Press and hold FUNC/SET for two seconds. The zone number will flash at the bottom of the screen. The upper limit is shown above the line in larger font, and the lower limit is below. (You may adjust the value for upper and lower rate limits in Zones 14 by using the PC software. Otherwise pressing ST/SP/- will simply activate or deactivate the preset alarm). 4. Press SELECT/+ or ST/SP/- to switch to Zone 5. 5. Press FUNC/SET again to display the SET screen 18 E 6. Press SELECT/+ or ST/SP/- to change the upper heart rate limit. Mode and check to make sure the watch is receiving your heart rate signals. 7. Repeat Steps 5 – 6 to set the lower heart rate limit. 8. Press FUNC/SET when finished. 3. Select the Training Zone that is most appropriate for your activity (refer to previous section). NOTE Heart rate range is between (upper 26-240 bpm) and (lower 25-239 bpm). 4. Activate the Stopwatch or Timer in CARDIO Mode (refer to the Stopwatch / Timer section). ACTIVATE THE TRAINING ZONE ALARM 5. Set up the TOUR Mode if you want to store a long-term record of your heart rate history that spans several training sessions or activities (refer to the TOUR Mode section). Once activated, the Training Zone Alarm will sound whenever you exceed the upper or lower heart rate limits for the selected Training Zone. Once you complete these steps, you are ready to begin exercising. After you finish, reset the Stopwatch or Timer to zero, then press FUNC/SET to have the following metrics displayed in 5-second intervals: 1. From the CARDIO Mode, press SELECT/+ to switch to the AL (Alarm) screen. • Time and date in M1 or M2….M99 (all current data will be stored under M1, while previous data is stored under M2 and so on until M99). 2. Press and hold FUNC/SET for two seconds. 3. Press SELECT/+ or ST/SP/- to select the desired Training Zone. • Average heart rate during exercise and Total exercise time 4. Press FUNC/SET. • Upper Training Zone limit and time spent above limit 5. Press ST/SP/- to turn the alarm off or on. • Lower Training Zone limit and time spent below limit • Total time spent exercising within the heart rate limits TRACK HEART RATE DURING TRAINING NOTE If you have more than one set (M1-M99) of training records, press SELECT/+ or ST/SP/- to loop through the records. To set up the OUTBREAKER watch so that it can track your heart rate activity during training, first do the following: 1. Put on the chest belt (refer to the “Wearing the Chest belt” section). 2. Press MODE to access the CARDIO 19 E STEP 1: ATTACH THE EQUIPMENT TO THE BICYCLE BIKE MODE (RP107 ONLY) The OUTBREAKER sports watch comes complete with a bicycle computer (and accessories), which records and displays the following information: • Speed: 0 – 255 km/hour or 0 – 158 mile/hour, depending on the measurement unit you select (refer to the Clock Mode section) • Average speed (Max:255km/hr or 158 mile/hr) • Maximum speed (Max:255km/hr or 158 mile/hr) • Cadence: 0 – 255 rpm (pedal revolutions per minute) • Distance traveled (Max:999.9 km or 620 miles) • Total distance travelled (Max:99,999.9 km or 620,000 miles) • Total time spent cycling Max 5 mm Max 100 cm The BIKE Mode comprises pioneering technology that uses two wireless sensors instead of one. The high frequency of each sensor (915.2 MHz) eliminates possible interference between the cadence and signal sensors, ensuring you accurate performance measurements. SET UP FOR BIKE MODE To set up the BIKE Mode you must first do two things: 1. Attach the measuring equipment to your bicycle:speed sensor (front wheel), cadence sensor (pedal), two magnets (front wheel and pedal), and bike mount (handle bar). Refer to the next section for instructions. 2. Specify your wheel circumference. See below for instructions. 20 E To attach the equipment: NOTE The watch can work with one or both sensors. 1. Attach the bike mount to the right or left handlebar using rubber grip, nut and bolt provided. Tighten until the bike mount is fixed into place, using the rubber grip for a firmer contact. 2. Attach the cadence sensor to a stationary point just behind the pedal, using the rubber grip for a firmer contact. There should be maximum 39 inches (100cm) between the sensor and the bike mount, and less than 30 degrees vertical angle. 3. Attach the cadence magnet to a pedal so that it is directly aligned with the sensor with less than 0.2 inches (5mm) between. 4. Attach the speed sensor to either leg of the front forks, using the rubber grip for a firmer contact. There should be maximum 39 inches (100mm) between the sensor and the 39 inches bike mount, and less than 30 degrees vertical angle. 5. Attach the speed magnet on a spoke of the front wheel so that it less than 0.2 inches (5mm) from the sensor. 6. Check and adjust as necessary, then snip the ends off the clips so that no excess remains. 7. Fit the watch into the bike mount. 8. Press MODE on the watch to switch to BIKE Mode. NOTE When the display shows a low battery icon (see ‘Battery’ section) replace the battery for the corresponding unit. STEP 2: ENTER WHEEL CIRCUMFERENCE You must set the bike’s wheel circumference on the watch so it can accurately calculate your speed and distance. If you do not know the bike’s wheel circumference, you can check the manufacturer’s specifications or measure it by marking the wheel where it touches the ground, and then rotating the wheel once fully along the ground. Measure the difference between the two marks. NOTE Most wheels have their specifications written on them. To specify this information on the watch: 1. Press MODE to switch to the BIKE Mode. 2. Press and hold FUNC/SET for 2 seconds. 3. Press SELECT/+ or ST/SP/- to change the circumference (cm or inches, depending on the measurement unit you selected in CLOCK Mode). 9. Press ST/SP/- to activate signal reception. The display shows “- -“, then changes to 0 once a successful signal is received. 4. Press FUNC/SET to save your changes. NOTE You can also use the PC software for this operation (see PC section). 10.Ride the bike a short distance to make sure signals are being sent to the watch successfully. 11.You are now ready to begin your trip. 21 E ACCESSING THE MODE OPTIONS PC KIT (RP107 ONLY) Press MODE to access the BIKE Mode, then press SELECT/+ to loop through the options: Speed, Stopwatch/Timer, Temperature, Altitude, and Heart Rate. The RP107 Oregon Scientific OUTBREAKER sports watch is equipped with a PC Kit that includes a PC Docking Station and CD-ROM for downloading information to a personal computer. Full instructions for using the software are provided in the online help and can be viewed once you have installed the CD-ROM. For instructions on how to use the Stopwatch or Timer in BIKE Mode, refer to pp. 9 – 10. NOTE The PC Kit for the RA107/RS107 series OUTBREAKER watch is sold separately. Contact the retailer or our website (www.oregonscientific.com) for more information about the RZ910 PC Kit. VIEWING SPEED AND CADENCE INFORMATION The PC Kit enables you to store and recall most of the information that is collected by the OUTBREAKER watch. This allows you to free up the watch memory for recording more information, while preserving the training records that are most important to you. For example, with the PC Kit you can specify which information you want to record in TOUR Mode: By limiting what is recorded, you can keep longer records. This can be useful if you wish to monitor your performance during an extended period such as a two-day hike, where only heart rate and altitude are of concern, or a day of cycling, where only speed and distance are important to you. Full details of the watch’s memory capacity are given in the TOUR MEMORY section. Press MODE to switch to the BIKE Mode. In the Speed display, you can view current speed (default view) and the following metrics from memory: total time spent cycling, total distance traveled, total TOUR distance traveled (TOUR Mode only, see TOUR section), average speed, maximum speed, and cadence (pedal revolutions per minute). Press FUNC/SET to loop through the values for each option. To clear a value from a specific memory, press and hold FUNC/SET for 2 seconds. You can also use the PC Hook-up Kit to set values on the watch through the PC. A full list of options is given at the end of this section. NOTE The hardware/software requirements for the PC Kit are listed at the back of this manual. 22 E USING THE SOFTWARE PC MODE Double-click on the Oregon Scientific icon. Once the software opens, click on Help for information about the function you require. SET UP FOR PC MODE To use the features of the PC Mode, you will need the PC Kit (includes PC docking station, connector cable, and the installation software CD-ROM), and a PC or laptop computer. NOTE All three models (RA/RP/RS 107) support the PC Mode. However, the PC Kit for the RA107 and the RS107 is sold separately. Diagram PC MODE OPTIONS Instructions 1. Connect the PC Docking Station to your computer. For best results, turn the computer off before you connect. You can perform the following tasks by using the CD-ROM software supplied. 2. Install the software using the CD-ROM (first-time use only). The process is automatic, and requires you to respond to self-explanatory prompts. Once the software is installed, an Oregon Scientific icon will be placed on your desktop. 3. Mount the watch on the docking station, making sure the contact points on the station and the watch are aligned. The watch should automatically switch to PC Mode. NOTE The cadence, speed and heart rate functions will be temporarily disabled when you use the watch in PC Mode. 23 Access/recall information/ on the PC Change watch settings on the PC • All information recorded in TOUR Mode, including temperature, altitude, heart rate, wheel speed, cadence, trip distance, etc, [Provided this data has been selected in “Data should be stored” in the “Configuration menu” (see software help menu)]. • Back up/import and export data • Define user data • Display graphical chart and print table • Give data overview with a specified duration • Date and time (set to PC time, or a manual setting) • Time, and event alarm (3 event alarms, 1 daily alarm, and select alarm duration) • Current sea-level pressure • Altitude limits • Weather icon • Upper and lower heart rate limits for Training Zones 1 – 5. • Wheel circumference/diameter • TOUR Mode data recording and download options • Choose a serial port (Com 1 to Com 4) • Sampling rate (1 second and up) • Unit settings (Metric or Imperial) E NOTE To send all selected settings and preferences to the watch select “Transfer configuration” in the “communication” sub-menu (PC software). EFFECTIVE USE AND RANGE The watch and heart rate chest belt have a maximum transmission range of about 30 inches (76 centimeters). If the signal is weak take the following steps: DOWNLOAD DATA • Shorten the distance between the heart rate chest belt and watch Follow these procedures to download data 1. After installing the CD-ROM click the OUTBREAKER icon on your PC. • Re-adjust the position of the heart rate chest belt • Check the batteries. If they are low or exhausted, change the battery immediately 2. In the man menu, select “Communication”. 3. Connect the docking station to your PC. You can wear the receiver watch on your wrist or strap it to a bike or exercise machine as shown below: 4. Press “Mode” until you reach PC Mode. 5. Fit the OUTBREAKER watch in the docking station, making sure the pins are matched and secured. 6. Close the cover gently and select “Connect” in the “Communication” sub-menu. 7. You will see an arrow mark on the watch, and “download in progress” on your PC. 8. Select “Read Trip Data” in the “Communication” sub-menu, then follow the on screen instructions. 9. Select “Format” to process the data arrangement. AQUATIC AND OUTDOOR ACTIVITIES 10.Download is now complete. Select desired graphical report. The watch is water-resistant up to 50 meters. The chest belt and other accessories (bike mount/speed and cadence sensors) are splash-proof up to 10 meters, but should not be worn for underwater activities, as the heart rate transmission cannot work properly under water. Refer to the table below for guidelines. 24 E SAFETY AND CARE INSTRUCTIONS SAFETY PRECAUTIONS RAIN SPLASHES, ETC 30m / 100ft 50m / 165ft 100m / 325ft OK OK OK SHOWERING SHALLOW DIVING / (WARM / COOL LIGHT SWIMMING SURFING / WATER ONLY) / SHALLOW WATER WATER SPORT OK OK OK NO OK OK NO NO OK SNORKELING / DEEP WATER DIVING Please observe these safety precautions when using this product. NO NO NO • Do not consult the watch while moving or engaging in active sports. Doing so may result in a collision that causes personal injury. When using the watch for outdoor sports activities, observe the following guidelines: • Do not subject the product to excessive force, shock, dust or temperatures. • Do not press the buttons underwater or with wet fingers. • Do not tamper with the product’s internal components. • Rinse with water and mild soap after use. • Do not mix fresh and old batteries, or batteries of different specifications. • Do not use the watch in hot water. • Do not use this watch as a substitute for professional measuring devices used in skydiving, hang gliding, paragliding, gyrocopter piloting and flying small aircraft. Tips for keeping your watch fit: Keep your watch water resistant! Avoid chemicals (gasoline, chlorine, perfumes, alcohol, hair sprays, etc.). Rinse after use. Reduce exposure to heat. Have your watch serviced by an approved service center once yearly. • Do not use this watch as a substitute for industrial precision instruments. • Follow the water-resistance guidelines carefully before use in water (see Effective Use and Range section). • Keep the product away from heat sources such as radiators, stoves, heaters, and other heat-generating products. CARE INSTRUCTIONS To ensure you receive the maximum benefit from using this product, please observe the following guidelines. 25 E • Cleaning – Clean with a damp cloth. Do not use liquid cleaning agents, benzene, thinner, or aerosols. Problem Remedy Reset time zone Cannot be changed when TOUR Mode is operating. Altitude Reading is less than Current altitude is Reset watch, or accept reading is 0 (-20, etc.) below ground, (watch reading strange sea level Different height setting)Barometric Minor pressure changes may produce minimal reading at same changes deviations in altitude point after trip readings No altitude Alarm does not Set levels (➔ 12) alarm Levels not set sound Temperature Too high Take off watch, wait 15 reading is Watch is too close to minutes, then try again strange body Remain at fixed altitude No weather Weather icon reading Height displacement for 5 minutes disappears Wrong unit Incorrect unit setting (Vertical movement) Set units (➔ 9) reading Unit settings (imperial/ metric) Set levels (➔ see relevant Expected alarm No alarm MODE Section) does not sound Levels not set Activate alarm (➔ see Alarm not activated relevant MODE section) Reset after you have Too high or low Pressure changed locations Is change due to reading is wind, pressurized strange chamber, or pressurized environment • Repair – Do not attempt to repair the product or modify the circuitry by yourself. Contact the retailer or a qualified repairman if the product requires servicing. Only use replacement parts that are recommended by the manufacturer. • Do not scratch hard objects against the LCD display as this may cause damage. TROUBLESHOOTING GUIDE This section includes a list of frequently asked questions for problems you may encounter with the OUTBREAKER sports watch. If your watch is not operating as you think it should, check here before arranging for servicing. Problem No power Date / time is wrong Symptom Power will not turn on. Check this Batteries are exhausted. Batteries are inserted incorrectly. Keys do not respond Key lock in operation. (Key icon shown) Date display is Date not set wrong Remedy Replace with new batteries. Insert the batteries correctly (➔7). Press key/lock for 2 seconds (Key icon will disappear). Set date correctly (➔9) Cannot be changed when TOUR Mode is operating. 26 Symptom Time display is wrong Check this Time zone set incorrectly E Problem Symptom Heart icon Blank display not working No heart rate Expected alarm alert does not sound No heart rate No heart rate data memory No bike reading/ Strange reading No data Check this (airplane)? Time out due to 5 minutes of inactivity Chest belt is too far from watch or poor skin contact Training Zone/Alert limits not set Chest belt is too far from watch or poor skin contact Sensor not ready Remedy Press MODE to return to CARDIO Mode Move chest belt closer or adjust contact with skin SPECIFICATIONS Calendar Clock Hour format Date format Auto calendar Alarms Set limits (➔ 18) Move chest belt closer or adjust contact with skin Chronometer/Timer Heart Rate Monitor Heart rate range Resolution Accuracy Training zones HR alert range Check distance between sensor and magnet Rx/Cx/Sx shown Replace batteries (➔7) No display Press ST/SP/No battery Watch not activated Display shows “- -“ then“0” No TOUR data Re-select check box in PC stored software Disabled feature Strange reading Measure and set wheel through PC Wrong wheel size set diameter again Strange reading Check sensor fittings (continued) Sensors fitted Realign magnet incorrectly Magnet not aligned Find source and move or switch off Interference No sensor Rx/Sx/Cx displayed Replace battery power in BIKE mode Battery low or empty No memory Empty memory, or Set tour mode used memory % Tour mode not set unchanged 100% of memory Clear all memories used manually, or download to Memory full the PC Alert memory TOUR memory Thermometer Range Resolution Accuracy Altimeter Range Resolution Accuracy Vertical speed NOTE Data manually erased cannot be recalled or recovered. 27 12/24 hr DD:MM:YY or MM:DD:YY 2000-2099 1 daily (hr:min) 3 event (hr:min DD.MM.YY) 99:59:59 (hr:min:sec) 25…240 beats per minute (bpm) 1 bpm +/- 1 bpm 26…240 bpm (upper) 25…239 bpm (lower) 3 heart rate alarms 99 max (RS107/RP107 only) 14.0º F….140.0º F (-10.0º C….60.0º C ) 0.2º F (0.1 º C) +/- 2º F (+/- 1º C) -1,312….30,000 feet (-400…9,000 meters ) 3 or 10 ft (1 or 3 m) +/- 30 ft (+/- 10 m) 0…415 ft/sec (0…125 m/sec) (ascending or descending) E Vertical speed resolution Max altitude change Total altitude change Alerts Barometer Local pressure range Sea level pressure range Resolution Accuracy Bar graph x-resolution Bar graph y-resolution 3 ft/sec (1 m/sec) 3 ft/sec (1 m/sec) +/- 180,000 ft (+/- 60,000 m) 1 alarm BIKE Computer Wheel speed range Wheel speed resolution Cadence range 598 min 5 second samplings: Altitude / Barometer / Temperature OUTBREAKER RS107 Record time: 508 min 5 second samplings: Heart Rate / Altitude / Barometer / Temperature OUTBREAKER RP107 Record time: 659 min 5 second samplings: Distance / Cadence / Speed / Heart Rate/ Altitude / Barometer / Temperature Environment Operation Storage Relative Humidity 14º F…140º F (-10º C…60º C) -4º F…158º F (-20º C…70º C) 10%…95% Water Resistance Watch Other accessories not actuating keys to 165 ft (50 m) splash proof Power Watch Chest belt Bike mount Cadence sensor Speed sensor 1 x CR2032 3V lithium battery 1 x CR2032 3V lithium battery 2 x CR2032 3V lithium battery 2 x LR44 1.5 V alkaline battery 2 x LR44 1.5 V alkaline battery Cadence resolution Max trip distance Max total trip distance Wheel circumference 300…1100 hPa (8.86…32.46 inHg) 900…1100 hPa (26.58…32.46 inHg) 1 hPa (0.03 inHg) +/- hPa (+/- 0.1 inHg) 1 hour 1 hPa (0.02953 inHg) TOUR Mode OUTBREAKER RA107 Record time: Circumference resolution Bike sensor RF 158 mile/hr (255 km/hr) 1 mile/hr (1 km/hr) 0…255 revolutions per minute (rpm) 1 rpm 620 miles (999.9 km) 62,000 miles (99,999.9 km) 39 in…118 in (1,000….3,000 mm) 0.04 in (1mm) 915.2 MHz 28 E • Do not subject the product to impact or shock. WARNINGS • Check all major functions when the device is unused for a long period of time. This is to ensure its full operation. Maintain a regular internal testing and cleaning of your device. To ensure you use your product correctly and safely, read these Warnings and the entire user manual before using the product. The warnings given here provide important safety information and should be observed at all times. • When disposing of this product, do so in accordance with your local waste disposal regulations. • Do not attempt to repair the product yourself. Contact the retailer or our customer service department if it requires servicing. • Take precautions when handling all battery types. They can cause injuries, burns, or property damage as a result of contact with conducting materials, heat, corrosive materials or explosives. Remove the batteries before storing the product for long periods of time. ADDITIONAL RESOURCES • The product is a precision instrument. Never attempt to take this device apart. There is a serious danger of powerful electric shocks. Visit our website (www.oregonscientific.com) to learn more about your OUTBREAKER sports watch and other Oregon Scientific™ products such as digital cameras, hand-held organizers, alarm clocks, and weather stations. The website also includes contact information for our customer service department, in case you need to reach us. • Do not, under any circumstances, touch the exposed electronic circuitry of the device as there is a danger of electric shock should it become exposed. © 2004 Oregon Scientific. All rights reserved. • Take special care when handling a damaged LCD display, as the liquid crystals can be harmful to your health. • Do not use or store the device, including the remote sensor, in locations that may adversely affect the product such as, snow, desert, and magnetic fields. • Do not use this device in aircrafts or hospitals. The use of radio frequency products can cause malfunctions in the control devices of other equipment. 29 E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. NOTE ON COMPLIANCE Consult the dealer of an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Company Name : Oregon Scientific, Inc. Address : 19861 SW 95th Place, Tualatin, Oregon 97062, USA Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Telephone Number : 503-639-8883 Website address : www.oregonscientific.com Company Name : IDT Technology Limited FCC : Address : Block C, 9/F., Kaiser Estate, Phase 1, NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 41 Man Yue Street, Hunghom, Kowloon, Hong Kong. Telephone Number : (852) 27647873 Website address : www.idthk.com Name and model number of the product : Oregon Scientific™ OUTBREAKER Sports Watch (RP107 series) However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CAUTION Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 30 — The content of this manual is subject to change without further notice. — Due to printing limitation, the displays shown in this manual may differ from the actual display. — The contents of this manual may not be reproduced without the permission of the manufacturer.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:05:24 11:08:24Z Subject : 1e-13/6 Modify Date : 2004:10:12 16:11:21+08:00 Page Count : 30 Creation Date : 2003:05:24 11:08:24Z Producer : Acrobat Distiller 4.0.5 for Macintosh Keywords : Author : LCD8600 Mod Date : 2004:10:12 16:11:21+08:00 Metadata Date : 2004:10:12 16:11:21+08:00 Description : 1e-13/6 Title : 1e-13/6 Creator : LCD8600EXIF Metadata provided by EXIF.tools