IDT Technology RTGR328NA-01 Remote Thermo-Hygro meter w/ R/C Clock User Manual RAR186 1

IDT Technology Limited Remote Thermo-Hygro meter w/ R/C Clock RAR186 1

User Manual

EN1CONTENTSContents ................................................................... 1Introduction .............................................................. 2About Oregon Scientific .......................................... 2Product Overview .................................................... 3Front View.............................................................. 3Back View .............................................................. 4Remote Sensor (THN122) ..................................... 5Getting Started ......................................................... 6Batteries ................................................................. 6Change Settings .................................................... 6Table Stand or Wall Mount ..................................... 6Remote Sensor (THN122) ........................................ 6Setup Sensor ......................................................... 7Data Transmission ................................................. 8Search for Sensor .................................................. 8Clock ......................................................................... 8Turn Atomic Clock ON/OFF ................................... 9Set Clock ............................................................... 9Switch Clock Display ............................................. 9Alarm ......................................................................... 9View Alarm Settings ............................................... 9Set Alarm ............................................................... 9Activate Alarm ...................................................... 10Snooze Alarm ...................................................... 10Temperature ............................................................ 10Select Temperature Unit ...................................... 10Select Sensor Channel ........................................ 10Minimum / Maximum Records ............................. 11Temperature Trend .............................................. 11Backlight ................................................................. 11Reset System ......................................................... 11Safety and Care ...................................................... 11Warnings ................................................................. 12Troubleshooting ..................................................... 12Specifications ......................................................... 13Main Unit Dimensions .......................................... 13Remote Sensor Dimensions ................................ 13Temperature ......................................................... 13Remote Sensor (THN122) ................................... 13Clock .................................................................... 13Power ................................................................... 13FCC Statement ....................................................... 14
EN2ABOUT OREGON SCIENTIFICVisit our website (www.oregonscientific.com) to learnmore about other Oregon Scientific products such asdigital cameras, hand-held organizers, health and fitnessgear, and projection clocks. The website also includescontact information for our customer service department,in case you need to reach us.INTRODUCTIONThank you for selecting the Oregon ScientificTM WirelessThermo Clock (RAR186). This device bundles precise timekeeping, alarm, and temperature monitoring features into asingle tool you can use from the convenience of your home.In this box, you will find:• Main unit• Remote sensor (THN122)Keep this manual handy as you use your new product.It contains practical step-by-step instructions, as wellas technical specifications and warnings you shouldknow.
EN312345678TEMPCHANNELMEMMODEPRODUCT OVERVIEWFRONT VIEW1. Sensor Temperature Area: Readings, trend line,sensor reception status and channel number2. Indoor Temperature Area: Readings, and indoorsymbol3. Clock Area: Time display with seconds or days ofthe week4. Calendar / Alarm Area: Date display and dual alarmdisplay5. MODE: Press to change display / settings6. MEM: Press to view current or saved max / mintemperature7. CHANNEL: Press to switch remote sensor8. ((.)): Press to view dual alarm settings
EN41257346BACK VIEW1. Wall mount2. °C / °F Switch3. Alarm (On / Off)4. Press (up button) to increase or (down button) todecrease settings5. Battery compartment6. Catch to open battery compartment7. Table stand
EN5REMOTE SENSOR (THN122)1. LED Status indicator12341. Wall mount hole2. RESET3. Channel number (1 - 3)4. Battery compartment(Battery compartment cover not shown)1
EN6TABLE STAND OR WALL MOUNTProduct can stand on detachable base or be mountedon a wall with a nail.GETTING STARTEDBATTERIESBatteries are not supplied with this product. You will needto purchase 2 x UM-3 (AA) 1.5V alkaline batteries forthe main unit, and 2 x UM-4 (AAA) 1.5V alkaline batteriesfor the remote sensor.Insert batteries before first use, matching the polarity asshown in the battery compartment. For best results,install batteries in the remote sensor before the mainunit. Press RESET after each battery change.Do not use rechargeable batteries.NOTE shows on LCD display when batteries are low.CHANGE SETTINGS1. Press and hold MODE for 2 seconds to enter settingmode.2. Press UP or DOWN to change settings.3. Press MODE to confirm.REMOTE SENSOR (THN122)This product is shipped with a THN122 Thermo Sensorthat collects Temperature data. Data can be collectedfrom up to 3 sensors. Additional sensors sold separately.
EN73. Place the sensor near the main unit. Press RESETon the sensor to initiate signal sending between thesensor and the main unit. The reception icon onthe main unit will blink for approximately 3 minuteswhile it is searching for the sensor. (Refer to theSensor Data Transmission section for moreinformation.)4. Close the remote sensor battery compartment.5. Secure the sensor in the desired location using thewall mount or table stand.SETUP SENSOROpen the remote sensor battery compartment with asmall Phillips screwdriver.1. Insert the batteries, matching the polarity as shownin the battery compartment.2. Set the channel. The switch is located in the batterycompartment.For best results:• Insert the batteries and select the channel andtemperature unit before you mount the sensor.• Place the sensor out of direct sunlight andmoisture.• Do not place the sensor more than 30 meters(98 feet) from the main (indoor) unit.• Position the sensor so that it faces the main(indoor) unit, minimizing obstructions such asdoors, walls, and furniture.• Place the sensor in a location with a clear viewto the sky, away from metallic or electronicobjects.• Position the sensor close to the main unitduring cold winter months as below-freezingtemperatures may affect battery performance andsignal transmission.You may need to experiment with various locations toget the best results.SWITCH OPTIONChannel Channel 1 - 3. If you are usingmore than one sensor, select adifferent channel for each sensor.
EN8SEARCH FOR SENSORTo search for a sensor, press and hold MEM andCHANNEL for 2 seconds.If the sensor is still not found, check thebatteries, obstructions, and remote unit location.Signals from household devices such asdoorbells, electronic garage doors, and home securitysystems may cause temporary reception failure. This isnormal and does not affect general product performance.The reception will resume once the interference ends.--- shows in TempAreasICON DESCRIPTIONMain unit is searching forsensors.At least 1 channel hasbeen found.Channel 1 is selected (numberwill change depending on thesensor you select)The selected sensor cannotbe found. Search for thesensor or check batteries.CLOCKThis product shows the current time, time zone, and dayof week in English, German, Italian, or French.Manually set the clock following the "Set Clock"instructions (below).SET CLOCK1. Press and hold MODE for 2 seconds. The ClockArea will blink.2. Select the hour, minute, date, month, language, dayand time zone offset (-12 to +12). Press UP orDOWN to change the setting. Press MODE toconfirm.The Language settings are (E) English, (D)German, (F) French, and (I) ItalianSWITCH CLOCK & CALENDAR DISPLAYClock with Weekday, Clock with Weekday and ZoneTime, and Clock with Weekday and Zone Calendar.NOTENOTENOTEDATA TRANSMISSIONData is sent from the sensor(s) every 30 seconds.The reception icon shown in the Temperature Areashows the status.
EN9SET DUAL ALARM1. Press ((.)).2. Press and hold ((.)) again for 2 seconds. The Alarmsettings will blink.3. Select the hour and minute. Press UP or DOWN tochange settings. Press ((.)) to confirm. To set second alarm perform step 1 twice,then perform steps 2 and 3.ACTIVATE ALARMPress ALARM ON / OFF to activate, deactivate and togglebetween alarm settings. (Alarm symbol with #1 or #2)shows in Calendar / Alarm Area when alarm(s) areactivated.TEMPERATUREThis product can display the following temperatureinformation:• Current, minimum and maximum readings• Trend line for remote sensorData is collected by the remote sensors and displayedevery 30 seconds.SELECT TEMPERATURE UNITSlide the °C / °F switch into the desired location. Theswitch is located on the back of the product.SELECT SENSOR CHANNELPress CHANNEL to switch between sensors 1 - 3.The icon shows the selected sensor.ALARMThis product is equipped with a 2-minute crescendo alarm.VIEW ALARM SETTINGSThe Alarm Time and On / Off status will show in theCalendar / Alarm Area.Press ((.)) again for the second alarm time and status.NOTEDesignatedDisplay RemoteDisplayChannel 1KineticwaveIconRemoteDisplayChannel 2RemoteDisplayChannel 3
EN10MINIMUM / MAXIMUM RECORDSPress MEM to toggle between current, maximum (MAX)and minimum (MIN) records for the indoor reading andthe selected sensor. To clear both the indoorthermometer and selected sensor records, press andhold MEM for 2 seconds.A beep will sound to confirm that the memory has beencleared.TEMPERATURE TRENDThe trend line is shown next to the Temperature reading.RESET SYSTEMThe RESET buttons are located in the batterycompartments for the main unit and sensors. PressRESET when you change the batteries and wheneverperformance is not behaving as expected (for example,unable to establish radio frequency link with remotesensor.When you press RESET, all settings will returnto default value, and you will lose all stored information.SAFETY AND CAREClean the product with a slightly damp cloth and alcohol-free mild detergent. Avoid dropping the product or placingit in a high-traffic location.WARNINGSThis product is designed to give you years of service ifhandled properly. Observe the following guidelines:•Never immerse the product in water. This cancause electrical shock and damage the product.•Do not subject the main unit to extreme force,shock, or fluctuations in temperature or humidity.•Do not tamper with the internal components.•Do not mix new and old batteries or batteries ofdifferent types.•Do not use rechargeable batteries with thisproduct.•Remove the batteries if storing this product for along period of time.•Do not scratch the LCD display.NOTEDo not make any changes or modifications to thisproduct. Unauthorized changes may void your right touse the product. The technical specification of thisproduct and contents of this user guide are subject tochange without notice. Images not drawn to scale.Rising SteadyTrend FallingICON
EN11TROUBLESHOOTINGCheck here before contacting our customer servicedepartment.SPECIFICATIONSMAIN UNIT DIMENSIONSL x W x H 150 x 82 x 47 mm(5.9 x 3.2 x 1.9 inches)Weight 7.90 ounces with batteryREMOTE SENSOR DIMENSIONSL x W x H 92 x 60 x 20 mm(3.6 x 2.4 x .79 inches)Weight 2.22 ounces without batteryTEMPERATUREUnit °C or °FIndoor Range -5 °C to 50 °C(23 °F to 122 °F)Outdoor Range -20 °C to 60 °C(-4 °F to 140 °F)Resolution 0.1 °C (0.2° F)Memory Min / MaxREMOTE SENSOR (THN122)RF frequency 433 MHzRange 30 meters (98 feet)with no obstructionsTransmission every 30 secondsChannel No. 1 - 3Unit °C or °FCLOCKClock display HH:MM:SSHour format 12hr AM/PMProblem Symptom RemedyCalendar Strange date /monthChange language( 9)Clock Cannot adjustclockSet Clock( 9)Temp Shows "LLL"or "HHH"Temperature is out-of-rangeCannotchangechannelCheck sensors. Onlyone sensor isworking( 7)Check batteries ( 6)Check location ( 6)RemotesensorCannot locateremotesensor
EN12Time zone offset -12 to +12 hoursCalendar DD/MM; weekday in4 languages (E, F, D, I)Alarm 2-minute crescendoPOWERMain unit batteries 2 x UM-3 (AA) 1.5ValkalineSensor batteries 2 x UM-4 (AAA) 1.5ValkalineFCC STATEMENTThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received,including interference that may cause undesiredoperation.Warning: Changes or modifications to this unit notexpressly approved by the party responsible forcompliance could void the user's authority to operatethe equipment.NOTE: This equipment has been tested and found tocomply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection againstharmful interference in a residential installation. Thisequipment generates, uses and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will notoccur in a particular installation. If this equipment doescause harmful interference to radio or televisionreception, which can be determined by turning theequipment off and on, the user is encouraged to try tocorrect the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipmentand receiver.• Connect the equipment into an outlet on a circuitdifferent from that to which the receiver isconnected.• Consult the dealer or an experienced radio/TVtechnician for help.DECLARATION OF CONFORMITYThe information below is not to be used as contact forsupport or sales. Please call our customer service number(listed on our website at www.oregonscientific.com, or onthe warranty card for this product) for all inquiries instead.
EN13WeName: Oregon Scientific, Inc.Address: 19861 SW 95th Place,Tualatin, Oregon 97062 USATelephone No.: 1-800-853-8883Fax No.: 1-503-684-8883declare that the productProduct No.: RAR186Product Name: Remote Thermo ClockManufacturer: IDT Technology LimitedAddress: Block C, 9/F, Kaiser Estate,Phase 1, 41 Man Yue St.,Hung Hom, Kowloon,Hong Kongis in conformity with Part 15 of the FCC Rules. Operationis subject to the following two conditions:1) This device may not cause harmfulinterference.2) This device must accept any interferencereceived, including interference that maycause undesired operation.
EN14Wireless Thermo ClockModel : RAR186User Manual
EN15© 2004 Oregon Scientific. All rights reserved.P/N.: 086-003347-02

Navigation menu