IDTECK STARRF-TINY Proximity Reader ( RF-Tiny) User Manual 285773

Download:
Mirror Download [FCC.gov]
Document ID	285773
Application ID	CePSVvs/wzVeWhgPQJp4Lg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	75.45kB (943105 bits)
Date Submitted	2002-11-25 00:00:00
Date Available	2002-11-25 00:00:00
Creation Date	2002-11-25 21:20:08
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2002-11-25 21:20:08
Document Title	Microsoft Word - 285773.DOC
Document Creator	PScript5.dll Version 5.2
Document Author:	fcc

STAR RF-Tiny
PROXIMITY READER
OPERATING AND
INSTALLATION MANUAL
RF-Tiny
Proximity Reader
Revision : 02
Date : November 16, 2001
ID TECK Co. Ltd.
RF TINY-20011117
-1-
STAR RF-Tiny
PROXIMITY READER
CONTENTS
RF TINY-20011117
1. Introduction
page 3
2. Identifying supplied parts
page 3
3. Specification
page 3
4. Installation
page 4
5. Wire Color Table of the Reader
page 5
6. Wire Connection to Controller
page 5
7. Operation
page 6
8. FCC Registration Information
page 7
9. Warranty and Service
page 8
-2-
STAR RF-Tiny
PROXIMITY READER
1. Introduction
The STAR RF-Tiny is an elegant looking and an attractive 4" read range proximity reader which
can be mounted to metal door frame(mullion) or any flat wall surface. The RF-Tiny use the
electronics module in epoxy potting that ensure you successful operation even in harsh
environments. Two color LED of green and red, inside Piezo buzzer sound will guarantee you an
accurate and reliable system operations.
2. Identifying supplied parts
Please unpack and check the contents of the box.
Reader Module
(1 ea)
RF-Tiny Bezel
(1 ea)
Instruction
(1 ea)
3. Specification
Read Range/Time
Up to 4"(10cm) / 30ms
Input Voltage/Current
DC 12V, Max. 150mA
Output Format
26 bit Wiegand, ABA Track II, RS232C
External Buzzer control Input
Low Active, DC 0 ~ 12V, Max. 50 mA
External LED control Input
Low Active, DC 0 ~ 12V, Max. 50 mA
LED/Buzzer
2 Color LED(Red and Green) / Piezo Buzzer
Color
Dark Gray
Operating Environment
-31 ~ 149 (-35 ~ +65 ), 0~90% Humidity
Overall Size(WxHxD)
1.77"x3.35"x0.65"(45x85x16.5mm)
Weight
0.157lb(71.5g)
RF TINY-20011117
-3-
STAR RF-Tiny
PROXIMITY READER
4. Installation
4-1. Mullion/Wall Mount
Drill two 3mm holes 2.72"(69mm) apart in vertical and drill one 1/2" hole for
the controller cable 1.36"(34.5mm) apart from the top hole.
4-2. Put controller cable into the center hole and install the controller module by using two
3-20 screws.
4-3. Put bezel into the controller module then push bezel until you hear the locking sound.
RF TINY-20011117
-4-
STAR RF-Tiny
PROXIMITY READER
5. Wire Color Table of the Reader
POWER
Power(DC +5V~+12V)
DC(+)
Power(DC Ground)
DC(-)(GND)
INPUT
Buzzer control input
BUZZER
LED control input
LED
OUTPUT(Wiegand Format)
Wiegand Data-0
Data-0
Wiegand Data-1
Data-1
OUTPUT(ABA Track II Format)
ABA(Card Present)
CP
ABA(Clock)
CLK
ABA(DATA)
Data
OUTPUT(RS232C Format)
RS232C(TX)
TX
6. Wire Connection to Controller
RF TINY-20011117
-5-
Red wire
Black wire
Blue wire
Yellow wire
Green wire
White wire
Orange wire
White wire
Green wire
White wire
STAR RF-Tiny
PROXIMITY READER
7. Operation
7-1. Apply power and you can see Red LED is on indicating the reader is in standby.
7-2. Present proximity card to the reader until you hear beep sound and the LED is
changing the color to Green simultaneously and the reader send RF card data to the
controller then LED changes the color to Red again for next reading.
7-3. LED Control;
To change the LED colors, you may connect LED Control Input(Yellow wire) to
power ground then the Green LED is on indicating the reader is in standby.
Present proximity card then the LED changes the color to Red simultaneously then
Green again for next reading.
7-4. Buzzer Control;
When the reader reads proximity card, only one beep sound generates in normal
operating mode but you can generate more beep sounds to distinguish whether the
access is granted or denied.
To generate more beeps, you may control the Buzzer Control Input(Blue wire) to power
ground then you can turn beeper on while you hold Buzzer Control Input to power ground.
RF TINY-20011117
-6-
STAR RF-Tiny
PROXIMITY READER
8. FCC REGISTRATION INFORMATION
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not expressly approved by the
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interface, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant to Part 15
of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the radio or television
off and on, the user is encouraged to try to correct interference by one or more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
RF TINY-20011117
-7-
STAR RF-Tiny
PROXIMITY READER
9. Warranty and Service
The following warranty and service information applies only to the United States of America and Republic of Korea.
For the information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed
below.
IN THE UNITED STATES
RF LOGICS Inc. Service Center
3026 Scott Blvd.,
SANTA CLARA, CA95054
Tel.:
(408) 980-0001
Fax.:
(408) 980-8060
E-mail: rflogics@rflogics.com
Web-site: www.rflogics.com
OUTSIDE OF THE UNITED STATES
ID TECK CO., LTD. Service Center
5F Ace Techno Tower Bldg.,
684-1 Deungchon-dong, Gangsuh-gu,
SEOUL 157-030, KOREA
Tel.:
+82 (2) 659-0055
Fax.:
+82 (2) 659-0086
E-mail: webmaster@idteck.com
Web-site: www.idteck.com
Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage,
include the following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to address
3. Ship-to address
4. Number and description of units shipped.
5. Name and telephone number of person to contact.
6. Reason for return and description of the problem.
NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made
directly to the carrier.
RF TINY-20011117
-8-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2002:11:25 21:20:08-08:00
Modify Date                     : 2002:11:25 21:20:08-08:00
Page Count                      : 8
Creation Date                   : 2002:11:26 05:20:08Z
Mod Date                        : 2002:11:26 05:20:08Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : fcc
Metadata Date                   : 2002:11:26 05:20:08Z
Creator                         : fcc
Title                           : Microsoft Word - 285773.DOC

EXIF Metadata provided by EXIF.tools