IDTECK STARRFK101 Proximity Reader With Keypad User Manual INSTRUCTION

Download:
Mirror Download [FCC.gov]
Document ID	285801
Application ID	bVIgWoktBLb1huD0Izw8OQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.15kB (251911 bits)
Date Submitted	2002-11-25 00:00:00
Date Available	2002-11-25 00:00:00
Creation Date	2002-10-30 18:06:11
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2002-10-30 18:07:26
Document Title	INSTRUCTION
Document Creator	Wordìš© Acrobat PDFMaker 5.0
Document Author:	최원석

ID-TECK
PROXIMITY READER
STAR RFK101
INSTRUCTION
Proximity Reader with KEYPAD
ID TECK Co. Ltd.
RFK101-20011219
-1-
ID-TECK
PROXIMITY READER
STAR RFK101
CONTENTS
1. Introduction
page 3
2. Identifying supplied parts
page 3
3. Specification
page 3
4. Installation
page 4
5. Wire Color Table of the Reader
page 5
6. Wire Connection to Controller
page 6
7. Operation
page 7
8. Output Format
page 9
9. FCC Registration Information
page 13
10. Warranty and Service
page 14
RFK101-20011219
-2-
ID-TECK
PROXIMITY READER
STAR RFK101
1. Introduction
The STAR RFK101 is an elegant looking and built in an attractive 4" read range proximity reader
with KEYPAD. The RFK101 has back lighting on the KEYPAD that ensure you successful
operation even the night operating. The KEYPAD allows you to access door with proximity card
and personal PIN numbers.
Three LEDs of green, yellow and red, inside Piezo buzzer sound will guarantee you an accurate
and reliable system operations.
2. Identifying supplied parts
Please unpack and check the contents of the box.
Reader unit
(1 ea)
Wall Mount
(1 ea)
O-ring
(5 ea)
Instructions
(1 ea)
3. Specification
Read Range/Time
Input Voltage/Current
Reset
LED/Beeper
Keypad
RFK101-20011219
Up to 4"(10cm) / 30ms
DC 12V, 150mA
Power on reset and WDT reset
3 LEDs(Red, Yellow and Green) / Piezo Buzzer
12key, Back lighting
-3-
ID-TECK
PROXIMITY READER
STAR RFK101
Color
Operating Environment
Dark Pearl Gray
-35℃ ~ +65℃, 10~90% Humidity
Overall Size(WxHxD)
Weight
Output Format
3.40"x3.94"x1.22"(487x100x31mm)
0.412 lbs(190 g)
26bit Wiegand, RS-232, ABA Track II Magstripe Output
Format with 8bit Burst or 3x4 Matrix Format for PIN
4. Installation
4-1. Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and one 1/2" hole at the center of
these two holes. (If you have installed electric gang box then skip this step.)
4-2. Using two 6-32 or M3 screws, install wall mount to the wall.
4-3. Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit through
the center hole and push the main unit to wall mount to lock the main unit and make sure
that the main unit is locked with wall mount.
RFK101-20011219
-4-
ID-TECK
PROXIMITY READER
STAR RFK101
5. Wire Color Table of the Reader
POWER
Power(DC 12V)
Power(DC 12V)
+12V
0V(GND)
Red wire
Black wire
CLS
RD1
RD0
TX
C0
C1
C2
R0
R1
R2
R3
Yellow wire
White wire
Green wire
Violet wire
White wire with blue band
White wire with green band
White wire with red band
Cyan wire
Pink wire
Orange wire
Gray wire
LED
BEEP
Brown wire
Blue wire
OUTPUT
ABA Track II(Card Present)
ABA Track II(Clock), Wiegand Data1
ABA Track II(Data), Wiegand Data0
RS-232 TX
KEYPAD 3x4 Matrix(Column0)
KEYPAD 3x4 Matrix(Column1)
KEYPAD 3x4 Matrix(Column2)
KEYPAD 3x4 Matrix(Row0)
KEYPAD 3x4 Matrix(Row1)
KEYPAD 3x4 Matrix(Row2)
KEYPAD 3x4 Matrix(Row3)
INPUT
LED Control
Beeper Control
RFK101-20011219
-5-
ID-TECK
PROXIMITY READER
STAR RFK101
6. Wire Connection to Controller
6-1. 26bit Weigand+RS232(for Card) and 8bit Burst format(for PIN)
. The Reader transmits Card data to Wiegand Data0,Data1 and RS-232 TX line.
. The Reader transmits PIN data to Wiegand Data0 and Data1.(8bit Burst format.)
6-2. ABA Track II+RS232(for Card) and ABA Track II+RS232(for PIN)
. The Reader transmits Card and PIN data to Card present, Clock, DATA and RS-232 TX line.
NOTE : You have to enter at least 1 numeric number(max. 8 numbers) followed by "ENT" key.
RFK101-20011219
-6-
ID-TECK
PROXIMITY READER
STAR RFK101
7. Operation
7-1. Connector Layout
7-2. Output mode Setting
Table 1. Jumpers Setting
JP1
JP2
Card Output format
Keypad Output format
close close
26bit Wiegand + RS232
8bit Burst (or 3x4 Matrix)
open
close
26bit Wiegand + RS232
26bit Wiegand + RS232(or 3x4 Matrix)
close
open
ABA Track II + RS232
8bit Burst (or 3x4 Matrix)
open
open
ABA Track II + RS23
ABA Track II + RS232 (or 3x4 Matrix)
Note: Default setting value for JP1 and JP2 jumpers are “close”(short circuit)
RFK101-20011219
-7-
ID-TECK
PROXIMITY READER
STAR RFK101
7-3. Operation
1. Once the power is applied, you should hear 3 times of initial beep sounds and red
And yellow LEDs on indicating that the reader is in standby mode after a
successful initialization and diagnostics.
2. Present proximity card to the reader until you hear the beeping sound and the
green LED on. The reader will send the RF card data to the controller then the
yellow LED on again for the next reading.
3. Enter the Keypad until you hear the beeping sound. The reader will send the Key
data to the controller.
4. LED Control:
To change the LED colors, you may connect the LED Control Input (brown wire) to
ground and the green LED will turn on indicating that the reader is in standby
mode. Present proximity card and the LED will change color to yellow then green
again for the next reading.
5. Beeper Control:
In normal operation, the reader generates one beep when it reads a proximity card,
However additional beeps can be generated to improve indication for access
status(granted or denied) by forcing the Beeper Control Input, blue wire to system
ground level. The beeper will remain on as long as the blue wire is connected to
system ground.
RFK101-20011219
-8-
ID-TECK
PROXIMITY READER
STAR RFK101
8. Output Format
8-1. 26bit Wiegand output format
1. Data format
Bit 1
Bit 2～9
Bit 10～25
Bit 26
: Even parity of bit 2 ~ bit 13
: Facility code (000 ~ 255)
: ID number (00000 ~ 65,535)
: Odd parity of bit 14 ~ bit 25
2. Timing diagram
8-2. ABA Track II Magstripe output format
1. Data format(for Card numbers)
RFK101-20011219
-9-
ID-TECK
PROXIMITY READER
STAR RFK101
2. Data format(for PIN)
3. Timing diagram
RFK101-20011219
- 10 -
ID-TECK
PROXIMITY READER
STAR RFK101
8-3. 8bit Burst output format(for PIN)
1. Data format
2. Timing diagram
RFK101-20011219
- 11 -
ID-TECK
PROXIMITY READER
STAR RFK101
8-4. RS-232 output format
1. Data format(Baud rate : 9600bps)
LSB
+15V
MSB
Space (=0)
+3V
Indeterminate
Region
0V
-3V
Mark (=1)
8 Data Bits
-15V
2 Stop Bits
Start Bit
Data packet corresponding to ASCII character 'A'
2. Data structure
START(0X02H)
DATA(8 Char)
END(0x03H)
LRC
(CARD output)
START(0X02H)
DATA(1~8 Char)
END(0x03H)
LRC
(Keypad output)
8-5. Matrix(3x4) format
1. Data format
Row0
Row1
Row2
Row3
RFK101-20011219
→
→
→
→
Column0
↓
ESC
Column1
↓
- 12 -
Column2
↓
ENT
ID-TECK
PROXIMITY READER
STAR RFK101
9. FCC REGISTRATION INFORMATION
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not expressly approved
by the responsible for compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the radio or television off and on, the user is encouraged to try to correct interference by one or
more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
RFK101-20011219
- 13 -
ID-TECK
PROXIMITY READER
STAR RFK101
10. Warranty and Service
The following warranty and service information applies only to the United States of America and
Republic of Korea. For the information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the service
facility listed below.
IN THE UNITED STATES
RF LOGICS Inc. Service Center
3026 Scott Blvd.,
SANTA CLARA, CA95054
Tel.:
(408) 980-0001
Fax.: (408) 980-8060
E-mail: rflogics@rflogics.com
Web-site: www.rflogics.com
OUTSIDE OF THE UNITED STATES
ID TECK CO., LTD. Service Center
5F Ace Techno Tower B/D,
684-1 Deungchon-Dong, Kangsuh-Gu,
SEOUL, KOREA 157-030
Tel.:
+82 (2) 659-0055
Fax.: +82 (2) 659-0086
E-mail: webmaster@idteck.com
Web-site: www.idteck.com
RFK101-20011219
- 14 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2002:10:30 18:07:26+09:00
Create Date                     : 2002:10:30 18:06:11+09:00
Page Count                      : 14
Creation Date                   : 2002:10:30 09:06:11Z
Mod Date                        : 2002:10:30 09:06:11Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : 최원석
Metadata Date                   : 2002:10:30 09:06:11Z
Creator                         : 최원석
Title                           : INSTRUCTION
Page Mode                       : UseNone
Tagged PDF                      : Yes

EXIF Metadata provided by EXIF.tools