IKUSI ELECTRONICA S L TR2400-EMB RADIO TRANSCEIVER User Manual IKORE v2

IKUSI ELECTRONICA, S.L. RADIO TRANSCEIVER IKORE v2

Contents

User Manual IKORE v2

ikoreUSER’s MANUALPaseo Miramón 170 - 20014 Donostia - San Sebastián, Guipúzcoa /Spain - tlc@ikusi.com
Tx Cr 1Cr 1These instruc ons must be read carefully in order to install and use the set properly and to keep it in perfect working condi on and to reduce the risks of misuse. Do not use this set on machines in poten ally explosive atmospheres, except the models cer fi ed ATEX/RATEX to work in that condi ons.a) Strictly adhere to the instruc ons for installa on contained in this manual.b) Make sure that professional and competent personnel carry out the installa on.c) Ensure that all site and prevailing safety regula ons are fully respected.d) Make sure that this manual is permanently available to the operator and maintenance personnel.e) Keep the transmi er out of reach of unauthorised personnel.g) On star ng each working day, check to make sure that the STOP bu on and other safety measures are working.h) When in doubt, press the STOP bu on.i) Whenever several sets have been installed, make sure the transmi er you are going to use is the right one. Iden fy the machine controlled on the label for this purpose on the transmi er or by using the display (in case it has one).j) Service the equipment periodically.k) When carrying out repairs, only use spare parts supplied by IKUSI dealers.WARNING• The equipment must be operated by qualifi ed personnel.• A er use, never leave the equipment ON (one or several transmi ers). Always set the STOP bu on to switch off posi on of the equipment to avoid accidentally to ac vate manoeuvres –specially in crane maintenance purposes-.• Do not use the set when visibility is limited.• Avoid knocking or dropping the set.• Do not use the set if failure is detected.REMEMBERChanges or modifi ca ons not expressly approved by IKUSI could void the user’s authority to operate this equipment.Remove the EEPROM in order to disable the transmitter When in doubt, press the STOP button Make sure the transmitter works with the machine to be handledDo not use the set when visibility is limited Avoid knocking or dropping the set01- SAFETY INSTRUCTIONS01- SAFETY INSTRUCTIONS
FCC/ISED Regulatory no cesModifi ca on statementIKUSI ELECTRONICA, S.L. has not approved any changes or modifi ca ons to this device by the user. Any changes or modifi ca ons could void the user’s authority to operate the equipment.IKUSI ELECTRONICA, S.L. n’approuve aucune modifi ca on apportée à l’appareil par l’u lisateur, quelle qu’en soit la na-ture. Tout changement ou modifi ca on peuvent annuler le droit d’u lisa on de l’appareil par l’u lisateur.Interference statement (if it is not placed in the device)This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Opera on is subject to the following two condi ons: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera on of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploita on est autorisée aux deux condi ons suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’u lisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep ble d’en comprome re le fonc onnement.Wireless no ceThis device complies with FCC/ISED radia on exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This transmi er must not be co-located or opera ng in conjunc on with any other antenna or transmi er.Le présent appareil est conforme à l’exposi on aux radia ons FCC / ISED défi nies pour un environnement non contrôlé et répond aux direc ves d’exposi on de la fréquence de la FCC radiofréquence (RF) et RSS-102 de la fréquence radio (RF) ISED règles d’exposi on. L’émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur.ÇFCC Class B digital device no ceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guar-antee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separa on between the equipment and receiver. - Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B) / NMB-3 (B)This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.
1.- Status LED2.- Crane selec on LED3.- Manoeuvre pushbu on4.- STOP bu on5.- External and extractable EPROM module 6.- Alkaline ba eries7.- START pushbu on8.- Hoist selec on pushbu on175684756402- TECHNICAL DESCRIPTION02- TECHNICAL DESCRIPTION612345387
SPECIFICATIONSIKORESTOP Function Cat. 3 - PldIngress Protection IP65 / NEMA 4Anti condensation system na.Frequency Band 2,4 GHzMain Mechanisms (Max. #) Pulador (6)Auxiliary Mechanisms na.Removable EEPROM ExternaBattery Model 4 Pilas AAAWeight (with Battery) Grams 315 gHarness Tira elástica / BandoleraDisplay na.Cable Connection na.Range Limiter na.Associated receivers R11Temperature range -20ºC +70ºCRelative Humidity Máx. 95% (without condensation)Storage temperatura range (24h) -25ºC / +75ºC (-13F/167ºF)Storage temperatura range —long periods- -25ºC / +55ºC (-13F / 131 ºF)02- TECHNICAL DESCRIPTION
RXIII13RXI /I+II /II* Data sheetIII[1][2] [3] Stand by III03- START UP2403- START UP1- Place a the EEPROM and the charged alkaline ba eries.In order to turn the transmi er ON (OPERATION mode), please follow the next steps:2- Push and pull out the STOP bu on. The status LED will blink in blue un l reach the Stand-by mode and will turn in fi xed blue.3- Press the start bu on. The status LED will blink in green un l the transmi er is linked with the receiver.4- When the receiver confi rms the link, the status LED will turn fi xed green. The system will be fully opera onal in order to ac on any maneouvre.When the systems controls two hoists, there will be a pushbu on for the selec on of individual or joint con-trol. I and II LEDs will show their selec on.
RECOMMENDATIONSThis equipment is designed for use in an industrial environment. However, we recommend you follow the instruc ons below to extend the life span of your remote control set:• Use the belt provided with the transmi er to prevent the transmi er from falling.• Do not clean the transmi er with solvents or pressurised water. Use a damp cloth or so brush.• Check the pushbu ons. In case of sings of deteriora on, please contact the Authorized Technical Service.• Check if the ba ery contacts are correct.• Systems are supplied with a pack of AAA alkaline ba eries. AAA alkaline ba eries or rechargable ba eries can be used (the cri c ba ery period it is not guaranteed with these ones).• It is recommended the use of new ba eries.04- MAINTENANCE04- MAINTENANCE AND TROUBLESHOOTING05- TROUBLESHOOTINGThe transmi er has status monitoring LED’s, which help to iden fy irregulari es. The most common signals of the Status LED are contained in the tables below:LED COLOUR / FREQUENCYPULSE FREQUENCYMEANING ACTIONBlue / Fast pulses Star ng the system, stablishing communica- on with radio and EEPROM. WaitBlue/ Con nuous Stand-by. Set up system, wai ng user’s ac on. PressSTART to enter in Opera on modeGreen / Fast pulses Trying to link with the receiver and wai ng its answer. WaitGreen / Con nuous Working. OperateGreen/ Slow pulses Latency. If no ac on has been taken during a  me. Press START to return to Opera on modeRed / Slow pulses EEPROM Error. EEPROM module mising or corrupt. Check EEPROM and reprogram if necessary Red / Double pulses Radio Error. Radio communica on error. Replace transmi erRed / Con nuous Ac vated maneuvre or harware failure if no order is ac ve. Release maneuvre or replace the transmi er Orange / Slow pulses Cri c ba ery signal. Replace ba eries with charged ones.

Navigation menu