IKUSI ELECTRONICA S L TR2400-EMB RADIO TRANSCEIVER User Manual IKORE v2

USER’s MANUAL

Paseo Miramón 170 - 20014 Donostia - San Sebastián, Guipúzcoa /Spain - tlc@ikusi.com

Tx Cr 1

Cr 1

These instruc ons must be read carefully in order to install and use the set properly and to

keep it in perfect working condi on and to reduce the risks of misuse.

Do not use this set on machines in poten ally explosive atmospheres, except the models

g) On star ng each working day, check to make sure that the STOP bu on and other safety measures

are working.

h) When in doubt, press the STOP bu on.

i) Whenever several sets have been installed, make sure the transmi er you are going to use is the

right one. Iden fy the machine controlled on the label for this purpose on the transmi er or by

using the display (in case it has one).

j) Service the equipment periodically.

k) When carrying out repairs, only use spare parts supplied by IKUSI dealers.

WARNING

• The equipment must be operated by qualifi ed personnel.

Changes or modifi ca ons not expressly approved by IKUSI could void the user’s authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Opera on is

subject to the following two condi ons: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired opera on of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploita on est autorisée aux deux condi ons suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)

l’u lisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep ble d’en

comprome re le fonc onnement.

Wireless no ce

This device complies with FCC/ISED radia on exposure limits set forth for an uncontrolled environment and meets the

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al

installa on. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guar-

antee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to

radio or television recep on, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

2.- Crane selec on LED

3.- Manoeuvre pushbu on

4.- STOP bu on

5.- External and extractable

EPROM module

6.- Alkaline ba eries

7.- START pushbu on

8.- Hoist selec on pushbu on

Battery Model 4 Pilas AAA

Weight (with Battery) Grams 315 g

Cable Connection na.

Range Limiter na.

Associated receivers R11

Temperature range -20ºC +70ºC

Relative Humidity Máx. 95% (without condensation)

green un l the transmi er is linked with the receiver.

LED will turn fi xed green. The system will be fully

opera onal in order to ac on any maneouvre.

When the systems controls two hoists, there will be a

pushbu on for the selec on of individual or joint con-

trol. I and II LEDs will show their selec on.

RECOMMENDATIONS

This equipment is designed for use in an industrial environment. However, we recommend you follow the

instruc ons below to extend the life span of your remote control set:

• Use the belt provided with the transmi er to prevent the transmi er from falling.