INFINIX MOBILITY XB02 Smart Bracelet User Manual

INFINIX MOBILITY LIMITED Smart Bracelet Users Manual

Users Manual

XBO2 smart bracelet User manual     1. Compatible system of  phone&BLE version    Android 4.4 or above      iOS 7.0 or above      Bluetooth 4.0 supply  1.Use preparation                                       OLED Touch Screen      Please ensure the device is full charged for the first time use,you need charge it by charging clip if the device can't power on. Please Charge by aiming at the charging point of wrist band: when connected to the power supply, it will be activated and display charging status. ※After  unpacking  the  bracelet→  turn  it  on    to  check  if  there  is  power;  If  it cannot be turned on→please use it after being charged for 2 hours.  1. Connect Under  the  requirement  of  the  adaptation  platform  (e.g.  1),  download  the corresponding mobile APP first:     3.1  APP  Download:  (1)Please  search  “WearFit  2.0”in  APP  store  or  Google  Play  and  android  A Hidden touch button  is here! sense light   Charge contact
market.  (2)Or scan the QR code  to download.(Tip: The download of other channels cannot guarantee that the APP is the latest version)    3.2    connect : Boot  (long  press  on  the  touch  button  (place  on  the  picture)  for  3 seconds)→  turn  on  the  Bluetooth  of  the  mobile  phone→  open  the  app  on  the  cell phone  "Wearfit2.0 → if to turn on the GPS (it can be chosen to be turned on when using a wrist band but the Bluetooth signal can not bee searched by the app)"→ to connect and bind (directly click into→mine →the connection management→ search the Bluetooth ID (click the one you selected )→ Click  "search" again if there is not any available→connect the wrist band→automatically switch to the main interface.) 3.3 login instructions: it can be logged in directly、by the third party (the third party platform)、 binding the wristband (click on the "binding wristband"→connect the  wristband→  click  on  the  "search"→  click  on  your  selected  Bluetooth  ID→ automatically return to the "home page", see if there is a "connected" notification above "+"). 1.  Start use  1.Once WearFit  2.0  is  connected with smart  bracelet, it  will  synchronize with  the  phone  time and smart bracelet continuous testing record.  2. It can be refreshed at the top of the APP homepage.  Beacelet operating:It will switch to following order as per single click the OLED touch button(The touch button  refer to the photo of function please): time  mode→Heart  rate  mode→Step  mode→Distancemode→Calorie  mode→Sleep  mode→Stopwatchmode→Search mode→Message reminder→Power off mode→Bluetooth ID    1.  Bracelet Features:       5.1    Time  mode:  3  seconds  after  pressing  the  touch  button  (with  vibration), there will be three kinds of time display modes; Single click on the touch button can switch the time mode; Press the touch button for 3 seconds (with vibration) on Version download
the  selected  time  display  mode  interface  to  choose.  (the  wristband  has  no  time  settings, it can only synchronize with the APP.)   5.2  Heart  rate measuring:After wearing the wristband, wait for about 60 seconds to show your heart rate. The wristband can measure the heartbeat continuously for every  time.  The  heart  rate  displayed  on  the  wristband  interface  is  the  latest measurement data. (During the measurement, the actual displayed heart rate may have minor deviation with the actual data due to the reasons that the wristband is not close  to  the  skin,  area  being  measured  has  dirt,  arm  hair  is  dense(hair  (1  cm) light color and medium dense), dark color of the skin (standards on brown, golden, medium white and lighter).  5.3 Step 、Distance、Calorie (only the displaying function) : automatically records daily  steps,  mileage  and  calories  consumed  while  walking;  And  automatically synchronize the data to the APP.  5.4  sleep measuring:Enter  the  app→  Mine-  personal  data  →sleep time  settings →save (notification of" successful ") 5.5 stopwatch function: enter (press the touch button for 3 seconds)→ enter the timer  function  (click  to  start  and  stop)→exit  and  clear  (long  press  the  touch button for 3 seconds). 5.6  Wristband looking for the phone (the  successful connection ) : enter (long press the touch button for 3 seconds)→look up (start and stop with single click on the touch button)→ exit (long press the touch button for 3 seconds).  5.7   SMS reminder: enter the app→Mine→  Device management→Intelligent reminder →SMS reminders to turn on and off. Start the SMS alert switch, and the wristband will vibrate when there a new text message.  5.8  Call  reminder:  Enter  the  app  →  Mine-equipment  management→  call notifications→single click to turn on or off.  Callreminder:  Enter  the  app  →  Mine-equipment  management→  call notifications→single click to turn on or off. 5.9  Power off: enter (press the touch button for 3 seconds)→ select "YES" (" NO "is returning to the previous level without turning off the machine)→ (long press the touch button 3 seconds).  5.10  APP「Wearfit2.0」 Features: 5.10.1 Tiredness level: click "single point measurement" to show your tiredness rate after 30S; And record it to display according to the day, week or month mode; You can also share the results with your friends. (click on the small icon on the upper  right  corner→  select  the  platform→  and  enter  the  selected  friends  (which
will be sent automatically in the screenshot).     5.10.2    Find  the  wristband:  click  "+"  on  the  home  page→   click  "find  the wristband", and the wristband will vibrate. (APP and wristband are successfully connected)     5.10.3  Anti  -loosing  notification:  mine  →  equipment  management  →  intelligent reminder  →  click  the  anti→loosing  notification  "off"  (close  \  open);  When  the wrist band is disconnected from the APP, the wristband will vibrate to remind you.     5.10.4  Alarm clock: mine →equipment management→smart reminder→click "+" to  set the alarm setting (<=8 times)     5.10.5    Long  sitting  reminder:  mine  →equipment  management→intelligent reminder→turn on the long sitting reminder→ set starting time and ending time and save.  The  wristband  will  automatically  monitor  the  state  of  the  activity.  If  the wristband  does  not  generate  the  number  of  steps  during  the  set  period,  the wristband will be automatically reminded. 5.10.6    No  disturbing  mode:  mine→  equipment  management→  smart  reminder→  no disturbing mode→ turn on the mode, set starting and ending time and save.  During this time, the wristband will stop receiving notifications from the phone.  5.10.7  Shake to take the picture: click "+" on the front page→ choose "shake to take a picture"→ shake the wristband to take a picture.  5.10.8  Raise  your  wristband  to  lighten  the  screen:  mine→  equipment management→ turn on the "raise your hand to lighten the screen"→ raise the wrist and the screen will automatically be lit up (the lit screen will be 5s).Method 1: wave your arm from 90 degree to 30-85 degree (normal angle for reading the screen), your band will automatically light up. Method 2: turn the screen surface away from your body, then turn the screen back to 30-80 degrees (normal angel for reading the screen), your band will light up.
1.Common problem   6.1While  binding  the  bracelet,  you  still  can ’ t  find  your  bracelet  or  can ’ t connect to the band? Android System: ①Please make sure you turn on Bluetooth on your phone, and the band doesn’t show bluetooth  symbol  (if  the  band  shows  the  Bluetooth  symbol,  it  indicates  the  band connected with your phone successfully). Stay close to you band, and try to search and connect again. Also please make sure your phone system is Android 4.4 or above. ②If still can ’t  connect,  go to  your  phone Setting — Application  Management — Permission  Management  —   Authority  Management,  then  find  Wearfit  2.0.  Choose “allowed” for all permission; then again enter Phone Setting — GPS, turn onypur phone GPS, restart your phone, and try to connect again. IOS System: Please make  sure you  turn on bluetooth on your phone, and the band doesn’t have Bluetooth symbol (if he band has Bluetooth symbol, it means the band successfully connected to other device). After onetime connection, your phone will remember the band. Every time you turn on the Bluetooth on your phone, the band and your phone will  automatically  connect  with  each  other.  If  you  want  your  phone to ignore  the device next time, please go to phone Setting—Bluetooth— Ignore the device. Then App can search your band again. 6.2 After binding the band but shows no connection, or shows connected but battery is 0%? In  this situation,  your  phone  doesn’t  bind  the  band  successfully,  please try  to bind again. 6.3 No data in the App? Pull down the Main surface and refresh, sync the data manually, then the App will show  the  data.  When  you  first  connect  the  band  with  your  phone,  the  App  will automatically  sync  the  data.  Later,  the  App  will  sync  the  data  automatically  at every integral time (ex: 7pm, 8pm) In addition, you need to turn on integral time measurement, all the step, heart rate, fatigue (graph) data are from integral time measurement. If you don’t turn on the integral time measurement, there is no graph data in fatigue measure.   6.4 After the APP  refresh, the data cannot be loaded? App Settings -- restore the factory Settings of the bracelet, click restore factory Settings, turn off the bracelet, then restart the bracelet to connect the app, and use the bracelet normally, the data can be loaded. 6.5  The time is not accurate? When there is no electricity in the bracelet, the time of bracelet may appear error after  refilling.  Please  connect  to  the  mobile  phone,  and  the  bracelet  will automatically synchronize the time of the phone to calibrate.  6.6  The time is not sync with your phone when you connect the app?
    phone  Settings  --  application  management/permission  management,  open  the permissions  of  the  app,  re-link  the  bracelet,  and  refresh  the  app  under  the main interface of the app.  7 basic parameters:  Screen size 0.66 bluetooth Bluetooth 4.0 Waterproof level IP67 Bettery Type Polymer lithium battery Battery capacity 105mAh Charge time 1.5-2H  Type aize 248mm*24.2mm*11mm Charging way Special charger  Packaging Smart  bracelet  +  charging  clip  + user manual.    Attention:  1、If there is a product quality problem or if there is any confusion about the use of the product, please contact our store directly and we will deal with it quickly.   1.The  measurement  results  of  this  product  are  for  reference  only,  not  for  any medical use and basis. Please follow the doctor's instructions and do not diagnose and treat yourself according to this measurement.  2.This product grade of IP67 waterproof, can be used for life cannot be used for diving  and  soak  in  water  for  a  long  time.  In  addition,  this  product  does  not prevent hot water, because the steam will affect the bracelet.  3.company reserves the right to modify the contents of this manual without prior notice. Some functions are  different in the  corresponding software  version, which is normal.
FCC Caution.  § 15.19 Labelling requirements.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  § 15.21 Information to user.  Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  § 15.105 Information to the user.  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  -Reorient or relocate the receiving antenna.  -Increase the separation between the equipment and receiver.  -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  -Consult the dealer or an experienced radio/TV technician for help.  * RF warning for Portable device:  The  device  has  been  evaluated  to  meet  general  RF exposure  requirement.  The  device can be used in portable exposure condition without restriction.

Navigation menu