INS Global S1-P 125K proximity card reader User Manual INSG IG B1 R01

INS Global Pty Ltd 125K proximity card reader INSG IG B1 R01

Users Manual

Regulatory InformationCE Mark The reader has passed all relevant tests and obtained CE approval.C Tick The reader has passed all relevant requirements for application of C Tick.FCCThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NoteThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna- Increase the separation between the equipment and receiver- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected- Consult the dealer or an experienced radio/TV technician for helpAny changes or modifications to this product not expressly approved in this document could void the user's authority to operate this equipment.Designed & Manufactured in Australia. Mifare ®is a registered trademark of Philips Electronics.Reader SpecificationsReader Output WiegandPower requirements +12VdcCurrent Consumption (+/- 5%) Normal Activated Read range Operating temperature Relative humidity 90% max, operating non-condensingReader dimensions (Facia) 67 x 50 x 16mmStatus LED’s Green/Red controlled by access controllerAudible tone Colour CharcoalIP rating Cable distances0.22mm2 cable0.33mm2 cable100m max250m max30 - 50mmWiringConnect the wiring as indicated in the table to the control panel. Connect the 0V reference and 0V (if provided in the power supply) to the ground (GND) Wire. Connect the W0, W1, LED and Buzzer Connect the +Vdc last.HandlingHandle the reader with care. Do not drop ordamage before installation.Mounting If necessary, drill holes for the mounting screws in the wall on which the reader will be placed. Alternately a back box can be used. Note magnet location for position of tamper reed switch (refer overleaf). Place the reader on the wall or back box, make sure wires are not crushed. Insert and hand tighten the screws. Check that the reader is level before tightening screws. Power up readerTroubleshootingIf the reader doesn’t respond when a valid smart card is presented, check the following:Symptom Possible Cause CheckLED is not litLED is orange/indeterminateor buzzer sounds lowReader doesn’t respondNo power to the readerVoltage to the reader is below minimum required levelInvalid card or card is faulty orwiring to the controller is faultyCheck power supply to the readerCheck power supply to the readerCheck reader with another valid smart card; if problem persists check wiringExternal UseMount the reader on a single gang box or suitable surface.Make sure the wire bundle to the reader has an IP rating of at least IP65.redCable Coloursblackyelloworangegreenwhite+5 to +12Vdc groundbuzzergreen ledW0W1WarrantyEach reader comes with a 3 year warranty from the date of dispatch. The warranty is void if the instructions contained within this document have not been adhered to.INS Global Pty LtdSuite 8166a The Entrance RoadErina NSW 2250www.insglobal.comPh: 1300 203 373Product of Australia S1-PINSTALLATION GUIDEModelINS - IG - B1 - R01MAGNETCUT OUT IN WALL REQUIRED :52 x 70mm (2.05 x 2.76”) FACIAWALLAPPLY DOUBLESIDED TAPELED ORIENTATIONTAMPER REED SWITCHLOCATION IF FITTEDFRONT VIEW SIDE VIEWNOT TO SCALE

Navigation menu