IOTTY SRL LSWU3 iotty Smart Switch User Manual
IOTTY SRL iotty Smart Switch
Contents
- 1. User Manual
- 2. User Manual_Compliance Info
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3880883 |
| Application ID | JXsdpzFFTwTC4Jz2jRgQQw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 12.43kB (155366 bits) |
| Date Submitted | 2018-06-08 00:00:00 |
| Date Available | 2018-09-07 00:00:00 |
| Creation Date | 2017-11-30 15:44:24 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2017-11-30 15:44:24 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS6 (Macintosh) |
Main power switch ON OFF Neutral Line ad Lo al utr Remove your old switch and label your wires. Remember that you must have a Neutral wire to install iotty Light Switch. Main power switch ON ON OFF OFF Ne Ne De vic utr al RL1 Load Ne Lin Switch (Line/Load) Turn off the power at the circuit breaker for the switch you are replacing. Lin al ner Ge ne li ON OFF RL1 Lo ad al utr Ne Connect Neutral wires together. Each RL has two wires, connect one to the Load and the other to the General Line together with the iotty wire labeled with L. In case you found the ground wire, just place it into the wall box. AR Push all the wires back into the wall box and try to allow as much space for the switch as possible. Place the iotty Light Switch into the box and screw in. Place the two black buttons down (or right if you have multiple gangs) ST Attach your iotty Light Switch faceplate starting from one of the two short side. To remove use a screwdriver to lift the faceplate. WARNING: Electrical wirings of the iotty Light Switch should be done by a professional electrician. Incorrect installation is dangerous or illegal. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work. Turn on the power at the circuit breaker. Download the iotty app and sign in. Connect to your iotty Light Switch wifi [IOTTY_serial-number]. Now go to the app and add a new device. How to install a multiple gang iotty Light Switch: A) In case of loads operating at B) In case of loads operating at different voltages than iotty. RL1 L N RL3 L N RL3 Overview of a iotty Light Switch with multiple gangs. LN RL2 Line ge lin eral Light 1 Light 3 Light 2 RL3 ut ra RL1 Line Line Ne more info at: www.iotty.com/support RL2 RL2 RL1 the same voltage than iotty. Load Load Load In both cases start with steps 1 and 2 A) Connect the Neutral wires together. Connect the General line wire, labeled with L, with one of the two wires that come out from each RL, together with the general wire from your wall. Connect each of the other wire of the RL with each load you want to control. B) Connect the Neutral wires together. Connect the General line wire with the line in the wall. Every RL has two wires, connect one to the external power supply (necessary if it has different voltage from the general line), Connect the other wire to the load. i2 i1 L N RL3 RL2 RL1 L N RL3 RL2 RL1 RL tr al Neu RL1 of i2 fi i1 RL eu Lin of fi 1o Line RL 2o In both cases finish following steps 4, 5 and 6. Remember: If you are connecting a three gangs switch you wonât be able to use one of the tree gangs. If you are making a 2 ways between two switches, one mechanical and one iotty, you wonât be able to control the iotty from the app, you will lose all smart functions. [For the instructions of this case go to www.iotty.com/support] How to install a multiple gang iotty Light Switch as a 2 way switch application (to control a load from two point). Instructions on the next page. tral ad Lo Start with steps 1 and 2. Choose which iotty will become i1 andv i2. iotty 1 (i1): Connect the Neutral wires together. Connect the General line wire with one of the two wires that come out from each RL, together with the General wire from your wall. Connect the other wire of RL1 with the RL2 of i2 and RL2 with the RL1 of i2. iotty 2 (i2): Connect the Neutral wire together. Connect the General line wire with the General wire from your wall. Connect one of the two wires that come out from each RL with the Load you want to control. Connect the other wire of RL1 with the RL2 of i1 and RL2 with the RL1 of i1. Now follow steps 4, 5, 6. Set the light in each iotty as Deviator. WARNING: Electrical wirings of the iotty Light Switch should be done by a professional electrician. Incorrect installation is dangerous or illegal. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work. iotty Light Switch
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2017:11:30 15:44:24+01:00 Metadata Date : 2017:11:30 15:44:24+01:00 Modify Date : 2017:11:30 15:44:24+01:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:6e84d248-9351-bc45-84df-5485547730d3 Original Document ID : xmp.did:058011740720681188C6859ACAC89E6E Document ID : xmp.id:2FF5280C3220681197A59C87A7A68055 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:008011740720681197A59C87A7A68055 Derived From Document ID : xmp.did:FA7F117407206811822ADAD4A45DF8FA Derived From Original Document ID: xmp.did:058011740720681188C6859ACAC89E6E Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2017:11:30 15:44:24+01:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools