IP Mobilenet B64450G25 Base Station for Mobile Radio Network User Manual 637246
IP Mobilenet, LLC Base Station for Mobile Radio Network 637246
Users Manual
IPSeries B64450G25 Base Station Product Ownerâs Manual Date Released: March 16, 2006 Document #: 516-80541-POM Version: B Copyright 2005 IPMobileNet, Inc. 16842 Von Karman Avenue, Suite 200 Irvine, CA 92606 Voice: (949) 417-4590 Fax: (949) 417-4591 The term âICâ: before the radio certification number only signifies that Industry of Canada technical specifications were met. Operation is subject to the following two (2) conditions: (1) this devise may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. The following U.S. Patents apply to this product: U.S. Patent numbers 5,640,695,6,018,647,6,243,393 Information contained in this document is subject to change without notice. All rights reserved. Reproductions, adaptations, or translation without prior written permission is prohibited, except as allowed under copyright laws. 637246.DOC Page 2 TABLE OF CONTENTS SECTION 1: THEORY OF OPERATION .............................................................................................. 4 General Block Diagram.................................................................................................................. 4 General Block Diagram Definitions ..................................................................................... 4 Input/Output ........................................................................................................... 4 System Controller................................................................................................... 4 Modems........................................................................................................... 5 Diversity Reception.......................................................................................... 5 RX Injection............................................................................................................ 5 Transmitter ............................................................................................................. 5 Receiver 1/ 2/ 3 ...................................................................................................... 5 Power Supply ......................................................................................................... 5 B64450G25 Base Station Section Descriptions.......................................................................... 6 System Controller................................................................................................................ 6 Input/Output ........................................................................................................................ 6 Modem Switching................................................................................................................ 6 Modem ............................................................................................................................... 7 Receive Signal Strength Indication Comparator................................................................. 7 Baseband ............................................................................................................................ 8 Receiver Board ................................................................................................................... 8 IF Amplifier .......................................................................................................................... 8 Receiver Injection................................................................................................................ 9 Exciter Board....................................................................................................................... 9 Analog Modulation ............................................................................................................ 10 Phase Locked Loop .......................................................................................................... 10 Power Amplifier ................................................................................................................. 11 SECTION 2: FACTORY TEST PROCEDURE .......................................................................................... 12 Equipment List ............................................................................................................................. 12 Programming and Configuring the Base Station ..................................................................... 13 Adjustment / Alignment Procedure............................................................................................ 14 Receiver Injection.............................................................................................................. 14 Receiver ............................................................................................................................ 14 Diversity Reception ........................................................................................................... 15 Receive Data..................................................................................................................... 16 Exciter ............................................................................................................................. 17 Power Amplifier ................................................................................................................. 17 SECTION 3: FCC LABEL.......................................................................................................................... 18 B64450G25 Base Station FCC Label Placement....................................................................... 19 B64450G25 Base Station FCC Label .......................................................................................... 19 APPENDIX A: B64450G25 TEST DATA SHEET ...................................................................................... 59 637246.DOC Page 3 SECTION 1: OVERVIEW Product Description The B64450G25 Base Station works within a frequency range of 450-507 MHz and requires 1/4wavelength antenna. The IPSeries Base Stations are intelligent devices designed for stringent requirements of mobile data communication systems. Intended for mounting in rack units, the base station requires very little room at tower sites and may be connected via Serial Line Internet Protocol (SLIP) or Ethernet ports. At the minimum, the unit requires a 13.8 VDC power supply, an antenna system, and a high-speed data connection to an Internet Protocol Network Controller (IPNC) system to operate. The base station is typically teamed up with a Power Amplifier (PA) and third-party system components such as antennae, preamplifiers, preselectors, filters, and combiners. Product Functionality The base station utilizes a high-performance DSP to modulate/demodulate 4 to 16-level Frequency-Shift Keying (FSK) modem for 25 kHz channel spacing, a multi-layered approach to signaling reliability, including patented multi-receiver Intelligent Diversity Receptionď, dynamic scrambling, data interleaving for burst error protection, Forward Error Correction (FEC), and Viterbi soft-decision algorithms. The IPSeries High Speed Base Station technology includes IPMobileNetâs Diversity Reception (DR) capability. Diversity Reception reduces the number of fades and the effects of multi-path reception. With the use of three (3) antennae, mounted as far apart as possible on the base station tower, the Diversity Reception System (DRS) minimizes the effects of fading. One of the antennae is likely to receive a viable signal while the others may not. DRS minimizes fading effects by comparing the signal levels from the three (3) antennae, and selecting the strongest signal. Diversity is most effective when the vehicle using an IPSeries Mobile Radio is in motion. 637246.DOC Page 4 SECTION 1: OVERVIEW External Features The base station technology is enclosed in a sturdy aluminum case. The external features consist of a series of connectors in the rear of the base station and light emitting diodes in the front of the base station, as described in this section. The product warranty becomes void if an uncertified or unauthorized individual removes the base station cover. The base stationâs rear external features consist of the following connectors and ports: TABLE 1: EXTERNAL FEATURES (Rear) FEATURE TX RX1/RX2/RX3 GPS Port BNC Power Connector DESCRIPTION Transmitter antenna connection Receivers 1, 2, and 3 antenna connections GPS antenna (SMA) connector Bayonet Neill Concelman connector used for measuring receiver sensitivity. 13.8 VDC base station power connector Serial Port 1 (DB9M) RS232 Serial Line Internet Protocol (SLIP) interface port (115K) Terminal Connection (DB9F) ANSI/TTY Terminal Connection (used for programming) (9600 bps, no parity, 8-databits, 1-stop bit) Ethernet Port 637246.DOC RJ45 Ethernet 10 Base T interface port Page 5 SECTION 1: OVERVIEW The base stationâs front external features consist of six (6) LED (light emitting diodes) indicators defined as follows: TABLE 2: EXTERNAL FEATURES (Front) LED Name TX Indicates that transmission is in progress CD Carrier detect indicates an RF message is detected RX1 Indicates that receiving is in progress on Receiver 1 RX2 Indicates that receiving is in progress on Receiver 2 RX3 Indicates that receiving is in progress on Receiver 3 POWER 637246.DOC When litâŚ. Indicates the base station is powered on Page 6 SECTION 2: BASIC NETWORK CONFIGURATION Basic Network Configurations This section provides basic network connection samples to help the user better understand some of the possibilities in setting up their respective systems. Each organizationâs configuration will differ based on its own system requirements, equipment, backhaul, etc. Basic Network Connection to an Existing LAN The following figure depicts a basic network connection for an existing Local Area Network (LAN) inclusive of one (1) Internet Protocol Network Controller (IPNC), one (1) base station, and multiple mobile radios, voice interface units (VIU), and mobile computers. It also includes other equipment such as a LAN VIU and a messaging server. Basic Network Connection with a Range of Base Stations The following figure depicts a basic network connection for a network inclusive of one (1) Internet Protocol Network Controller (IPNC) and a range of base stations, mobile radios, mobile computers, and additional components that interface with this sample system setup. For serial connectivity to Ethernet only systems, please refer to the IPTurbo Converter Quick Reference Guide (IPMN p/n: 516.80496.QR) on the Production Documentation CD (IPMN p/n: 480.0001.001). 637246.DOC Page 7 SECTION 3: PRODUCT SETUP AND PRELIMINARY TESTING Base Station Setup Intended for rack unit configuration, the base station can be installed in an existing rack or assembled into a rack of its own. Rack Unit Mounting The table below lists the required components for a base station setup. TABLE 3: BASE STATION COMPONENTS REQUIRED FOR INSTALLATION QTY DESCRIPTION Frequency appropriate IPSeries Base Station Ethernet cable 5â DC power input cable with connector RF coaxial cables (may require an additional cable if connecting the base station to a power amplifier) 637246.DOC Page 8 SECTION 3: PRODUCT SETUP AND PRELIMINARY TESTING Preliminary Testing This section provides a functional preliminary test for the base station prior to installation. It is used to determine the condition of the new base station prior to placing into service. If the base station is nonfunctional after completing this test, refer to Chapter 6: Customer Support. This section applies to all base station frequency ranges. Checklist of Required Material The following checklist provides a list of tools required to perform this preliminary test procedure. TABLE 4: CHECKLIST OF REQUIRED EQUIPMENT FOR PRELIMINARY TESTING OF A BASE STATION Calibrated Base Station System â Consisting of the following components: (1) Frequency appropriate IPSeries Base Station (2) Desktop or laptop configured as an Internet Protocol Network Controller (IPNC) (3) Corresponding IPSeries Mobile Radio tuned to Base Station frequencies (i.e.: if an IPB138 base, use IP138 mobile) (4) Desktop or laptop with two (2) available serial ports with Microsoft Windows 98 or higher, IPMobileNet Dial-Up Networking, IPMessage software, and HyperTerminal for base station installed (5) Base Station power cable DC power supply with ammeter, with the appropriate volts, see page 7 Current Consumption for each base station (Astron VS12M or equivalent) Six (6) antennae (generic mag mounts) tuned to frequency of transceiver Serial Base Station Interface No. Requirement DB9 RS232 serial cable IPTurbo Converter (IPMN p/n: 900.00012.01) IPTurbo Converter Reference Manual (IPMN p/n: 516.80496.REF) Ethernet Base Stations Interface No. Requirement Ethernet RJ45 Cable Ethernet Cable 637246.DOC Page 9 SECTION 3: PRODUCT SETUP AND PRELIMINARY TESTING Preliminary Test Procedure Perform the following initial setup to prepare the base station for preliminary test: Step 1 Connect the antenna to the base stationâs TX port. Step 2 Connect the base station to the 13.8 VDC power supply. Step 3 Power on the base station and verify that the LEDâs illuminate and the power LED on the front panel remains illuminated. Step 4 Verify that the base station DC-supply current is <1.2 Amps. Step 5 For the ideal Serial or Ethernet setup please refer to the IPTurbo Converter Reference Manual (IPMN p/n: 516.80496.REF) available on the Product Documentation CD enclosed with this product. Step 6 Connect the antenna to the mobile radio. Step 7 Power on the mobile radio. Step 8 Recycle the base station power. Step 9 Connect the antennae to the base stationâs RX1. Step 10 Verify that the RX1 and CD LEDâs are illuminated when the mobile radio is attempting to connect. Repeat steps 9 and 10 with RX2 and RX3. Step 11 From the mobile PC, open the DOS prompt, then ping the IPNC with the following command: ping 172.16.23.200 (replacing with the appropriate IPNC IP address). Press [ENTER] and verify that the IPNC responds to the ping request. Also verify that the base station carrier detect (CD) LED is lit followed by the TX LED. 637246.DOC Page 10 SECTION 4: PRODUCT INSTALLATION Installation Overview This chapter provides the basic setup involved in the installation process of an IPSeries High Speed Base Station. For backhaul requirements, refer to Appendix A of this document. Standard considerations such as air flow clearance above the base station for heat dissipation and ensuring adequate space exists behind the base station for the routing of cables are of primary importance. A minimum clearance of 1 rack space is recommended for natural convection cooling. Adjustment points are available through holes in the base stationâs bottom cover. Sufficient space below the base station should exist to facilitate adjustments. Coax, power, and interface cabling service lengths with neat routing will make the removal and replacement of the base station easier for functional testing and maintenance purposes. To prevent injury and damage to the base station, exercise extreme caution throughout the installation process and follow the reminders listed below.  Follow safety precautions for handling rack unit installations.  Do not alter the components listed in the Installation Requirements section, unless substituions are noted within this chapter. 637246.DOC Page 11 SECTION 4: PRODUCT INSTALLATION Installation Instructions If setting up a new rack unit, make sure to complete the rack unit setup according to the Manufacturersâ instructions. Base Station Installation into the Rack Unit Receiver and Transmitter Connections To connect the base station, perform the following steps: Step 1 Connect the RF coaxial cable to Receiver 1 (RX1) on the back of the base station. Step 2 Route the cable neatly toward the top of the rack. Allow a little slack in the cable to avoid accidental disconnection. Step 3 Connect the RF coaxial cable to Receiver 2 (RX2) on the back of the base station. Step 4 Route the cable neatly toward the top of the rack. Allow a little slack in the cable to avoid accidental disconnection. Step 5 Connect the RF coaxial cable to Receiver 3 (RX3) on the back of the base station. Step 6 Route the cable neatly toward the top of the rack. Allow a little slack in the cable to avoid accidental disconnection. For clear identification for troubleshooting and/or maintenance activities, avoid crossing the coaxial cables. Step 7 Connect the RF coaxial cable to the Transmitter (TX) connection on the back of the base station. Step 8 If connecting to a power amplifier (as shown in the figure below), connect the cable from the base station to the power amplifier via the Transmitter (TX) connection. If not connecting to a power amplifier, skip to Step 11. Step 10 If a power amplifier is used, connect an RF coaxial cable to the output port of the power amplifier. Step 11 Route the cable neatly toward the top of the rack. Allow a little slack in the cable to avoid accidental disconnection. Step 12 To perform the RX1, RX2, RX3, and TX antenna connections, refer to the Typical Antenna Configuration section in this chapter. 637246.DOC Page 12 SECTION 4: PRODUCT INSTALLATION Figure 8: Base Station Mounting and Connection in the Rack Unit (Rear View) 637246.DOC Page 13 SECTION 4: PRODUCT INSTALLATION Single Base Station Configuration Figure 9: Base Station Ethernet Connection To connect a single base station, perform the following steps: Step 1 Plug in the Ethernet cable into the Ethernet port on the base station (as shown in the figure above). Step 2 Route and plug in the other end of the Ethernet cable to an Ethernet switch or router. Step 3 Route and plug in another Ethernet cable from the Ethernet switch or router to the Ethernet port of the Internet Protocol Network Controller (IPNC). If connecting to a Serial backhaul, an IPMobileNet IPTurbo Converter is required. For connection instructions, refer to the IPTurbo Converter Reference Manual (IPMN p/n: 516.80496.REF) available on the Product Documentation CD provided with this product. Multiple Base Station Configurations To connect multiple base stations, perform the following steps: Step 1 Plug in the Ethernet cables to the back of each base station (as shown in the figure above) and route according to selected setup. Refer to the IPTurbo Converter Quick Reference Guide (IPMN p/n: 516.80496.QR) for setup instructions and scenarios. Step 2 Route and plug in the Ethernet cables to an IPMobileNetâs Internet Protocol Network Controller (IPNC) via the hardware as defined by the organizationâs configuration. If connecting to a serial backhaul, an IPMobileNet IPTurbo Converter is required. For connection instructions, refer to the IPTurbo Converter Reference Manual (IPMN p/n: 516.80496.REF). 637246.DOC Page 14 SECTION 4: PRODUCT INSTALLATION Typical Antenna Configuration Base station antenna configurations may vary from site to site depending on the type of mounting structure, the presence of existing antennae, mounting structure loading limitations, etc. The following information is provided as a guideline for a typical scenario. Figure 10: Typical Antenna Configuration An optimal antenna mounting configuration is shown in the figure above. The transmit antenna and receive antennae are located at different elevations. This vertical separation provides the greatest degree of isolation between transmit and receive antennae. The three (3) receive antennae are mounted at the same elevation and are oriented in a 120 degree triangular pattern. A triangular orientation of the receive antennae provides optimal diversity performance in an omnidirectional pattern. The greater the separation between receive antennae, the greater the diversity gain; therefore, the distance between antennae should be made as great as is practical. In the event only two (2) receive antennae are used (i.e. a dual receiver diversity reception system), the receive antennae should be mounted in a broadside orientation with respect to the radio coverage area. To prevent the antennaâs radiation pattern from becoming distorted, the immediate area surrounding each antenna should be kept free from conductive objects (i.e. other antennae, guy wires, or the tower structure itself). The amount of clear area required to prevent pattern distorion is equal to the antennaâs near-field exclusion. 637246.DOC Page 15 SECTION 4: PRODUCT INSTALLATION Near-Field Exclusion Zone The near-field exclusion zone (NFEZ) is the required distance between antennae to any other surfaces to improve transmit and receive performance. The large radio frequency field that builts up around the antenna upon transmitting is essential for proper data transmission. It can be severely corrupted by metal objects in the NFEZ. As seen in the previous figure, the transmitting antenna is placed at the very top of the tower especially if the base station will be required to transmit in all directions (omni-directional). If the transmitting antenna cannot be positioned on the top of the tower and must be placed on a tower arm, then it is important to realize that coverage will be shaded in the area behind the tower from the anetnna. The installer must be certain that the area of desired coverage is away from the tower and not behind it. Receiving and transmitting antennae should not be on the same plane, especially VHF and UHF systems where the frequency splits are relatiely small. An antenna in the near-field exclusion zone that is tuned for the same frequency as the transmitting antenna will reradiate the signal and create unwanted effects on the transmittal signal. The receivers will be inundated by high levels of radio frequency energy from the transmitting antenna. This is why it is important to include vertical separation in the plan for the base station installation. The isolation provided by 30 feet of vertical spearation can dramatically improve the performance of the base station. An antennaâs NFEZ can be calculated as follows: Where: 2d2 Îť D is the distance to the anennaâs near field boundary d is the antennaâs longest linear dimension (in the same units as D) Îť is the wavelength (in the same units as D) Maximizing the distance between the receive antennae will provide maximum diversity gain and will minimize antenna radiation pattern distortion. 637246.DOC Page 16 SECTION 4: PRODUCT INSTALLATION Power Connection Figure 11: Base Station Power Connection To connect the base station power connector, perform the following steps: Step 1 Connect the power cable to the base station power supply connection (as shown in the figure above). Step 2 Connect the wires to the appropriate output (+ and -) output posts on the power supply (as shown in the figure above). 637246.DOC Page 17 SECTION 4: PRODUCT INSTALLATION Post Installation Checklist The following table lists the tasks that should be performed upon completing installation. TABLE 5: POST INSTALLATION CHECKLIST NO. CHECKLIST ITEM Scope out the entire area setup to locate any obvious problem areas. Check antenna routing for safety concerns and near-field boundary setup. Use tie wraps, where possible to ensure that all cables routed in parallel are bundled together. Perform appropriate testing to ensure base station works properly. 637246.DOC Once installation is complete make sure the area is clear of debris that would prevent proper airflow and ventilation. Page 18 SECTION 5: FACTORY TEST PROCEDURE Equipment List The following table lists the equipment required to perform the B64450G25 Base Station Factory Test Procedure. TABLE 6: EQUIPMENT REQUIRED TO PERFORM FACTORY TEST PROCEDURE QTY DESCRIPTION MANUFACTURER MODEL PCâs (one for mobile, one for base) Windows 9X w/ IPMessage AVR IPSeries High Speed Base Station IPMobileNet B64450G25 IPSeries High Speed Mobile Radio IPMobileNet M64450G25 Service Monitor â Communication Test Set HP 8920A or B or equivalent High Frequency Probe HP 85024A Power Supply for 85024A Probe HP HP1122A Channel Scope Tektronix TDS 460A General Purpose Probe Scope Digital Multi-Meter Fluke Tektronix Dmm91277 DC power supply with ammeter, 13.8V, 12 Amps or more Astron VS12M or equivalent 100 watt dummy load/attenuator Pasternack PE7021-40 or equivalent UHF Antennae (generic mag mount) Serial Cable DB9M â DB9F connectors (generic) IPMobileNet 156.0245.020 Input/Output (I/O) Board IPMobileNet 502.80081 IPSeries High Speed Base Station power cable Serial DB9F-DB9M Null Modem cables 637246.DOC Page 19 SECTION 5: FACTORY TEST PROCEDURE Programming and Configuring the Base Station This section applies to the 450 to 507 MHz frequency range of the IPSeries Base Station. Important! The base stationâs IP address must be known prior to performing the procedures in this section. The programming procedure should be performed when it is necessary to upgrade a base stationâs Firmware or to change the operating parameters to suit client needs. Viewing the Base Stationâs Configuration Data Step 1 At the HyperTerminal window, type in the appropriate password and press [ENTER]. Step 2 Type ? and press [ENTER]. The following example displays in the HyperTerminal window: Host serial = 115200,N,8,1, timeout=200 Host framing = SLIP, no split frames no status messages tunnel = 0 TX format = new Injection = LOW SIDE, 45MHz channel spacing = 25000 Channel = 0 Channel Tx freq Rx freq Inj freq Frequency=0 , 450.000000, 463.000000, 418.000000 Serial number: yyyyyyyyy RIM address = 1 Frequency group = 1 TX quiet time = 5 Symbol sync time = 12 milliseconds, 0 extra inter-split-frame count TX tail time = 5 Radio data rate = 19200 Max data tx time = 60 seconds Carrier detect delay time = 1 millisecond Station ID = ABC123 Station ID time =10 minutes Polarity = TX+, RX+ Allow crc errors = 0 Suppress keep alive = 0 Allow base to base = 0 Timeslot status = 0 Duplicate time = 10 milliseconds Control head grant delay = 50 milliseconds RIM DD delay = 0 milliseconds Retry interval = 0 milliseconds Retry time limit = 0 milliseconds RSSI step = 25 (=19dBm) IPNC = 192.168.3.3 SLIP Address = 192.168.4.6 RF IP Address = 192.168.3.1 SNTP interval = 60 seconds num timeslots = 16 timeslot period = 992ms timeslots per voice packet = 4 noise = -128dBm Fixed TX Delay = 0 milliseconds Scale TX Delay = 0 microseconds 637246.DOC Page 20 SECTION 5: FACTORY TEST PROCEDURE Adjustment / Alignment Procedures Make appropriate notations of any items that require attention during this procedure. This information is needed later during the repair process. Startup Step 1 Remove the base station cover placing the screws in a location where they will not be misplaced. Step 2 Connect the base station to the appropriate components. Step 3 Power up the base station and computer. The power supply ammeter must read 1.2 amps or less with a 13.8 VDC input. Receiver Injection Step 1 Using the HP high frequency probe verify that the receiver injection frequency is present at each of the three (3) receivers by monitoring the receivers R24 surface mount pad which lies on the 50 ohm track between P1 and C43. Step 2 Adjust R23 on the receiver injection circuit board to set the injection frequency within 10 Hz of the exact injection frequency. The amplitude of the injection frequency should read approximately +5 dBm Âą1 dBm. Receiver Step 1 Using the high frequency probe, monitor the 44.545 MHz second injection frequency at U6 pin 3, adjust trimmer capacitor (C22) to the center of the oscillatorâs oscillation range. The amplitude level of pin 3 of U6 should read between +5 and +10 dBm. Step 2 Inject an on-frequency signal at a level of â80 dBm, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into the receiver under test. Step 3 Check the receiverâs sensitivity, verifying that the SINAD is 12 dB or better at a maximum level of â119 dBm (-120 is typical). 637246.DOC Page 21 SECTION 5: FACTORY TEST PROCEDURE Diversity Reception Step 1 Inject an on-frequency signal at a level equal to Receiver 1 12dB SINAD level, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 1. Step 2 While monitoring TP1 with the digital multi-meter, adjust RSSI1 low adjust potentiometer (R12) for a reading of 0.750 VDC Âą10 mV. Step 3 Increase the amplitude of the signal by 50 dBm. Step 4 While monitoring TP1 with the digital multi-meter, adjust RSSI1 high adjust potentiometer (R11) for a reading of 2.75 VDC Âą10 mV. Adjustments R11 and R12 are interactive adjustments, therefore continue adjustments until the DC voltage at TP1 is 0.750 VDC for the receiverâs 12 dB SINAD level and 2.75 VDC for a 50 dBm increase from the receiverâs 12 dB SINAD level. Step 5 Inject an on-frequency signal at a level equal to Receiver 2 12dB SINAD level, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 2. Step 6 While monitoring TP2 with the digital multi-meter, adjust RSSI1 low adjust potentiometer (R10) for a reading of 0.750 VDC Âą10 mV. Step 7 Increase the amplitude of the signal by 50 dBm. Step 8 While monitoring TP2 with the digital multi-meter, adjust RSSI1 high adjust potentiometer (R9) for a reading of 2.75 VDC Âą10 mV. Adjustments R9 and R10 are interactive adjustments, therefore continue adjustments until the DC voltage at TP2 is 0.750 VDC for the receiverâs 12 dB SINAD level and 2.75 VDC for a 50 dBm increase from the receiverâs 12 dB SINAD level. Step 9 Inject an on-frequency signal at a level equal to Receiver 3 12dB SINAD level, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 3. Step 10 While monitoring TP3 with the digital multi-meter, adjust RSSI1 low adjust potentiometer (R33) for a reading of 0.750 VDC Âą10 mV. Step 11 Increase the amplitude of the signal by 50 dBm. Step 12 While monitoring TP3 with the digital multi-meter, adjust RSSI1 high adjust potentiometer (R35) for a reading of 2.75 VDC Âą10 mV. Adjustments R33 and R35 are interactive adjustments, therefore continue adjustments until the DC voltage at TP3 is 0.750 VDC for the receiverâs 12 dB SINAD level and 2.75 VDC for a 50 dBm increase from the receiverâs 12 dB SINAD level. 637246.DOC Page 22 SECTION 5: FACTORY TEST PROCEDURE Step 13 Inject on-frequency signal at a level of â80 dBm, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 1. Step 14 While monitoring the AC voltage at TP6 adjust audio 1 AC adjustment potentiometer (R72) for 350 mVRMS (Âą1 mV). Step 15 While monitoring the DC voltage at TP6 adjust audio 1 DC adjustment potentiometer (R57) for 2.500 VDC (Âą1 mV). The audio AC and DC adjustments are interactive, therefore continue adjusting R72 for 350 mVRMS and R57 for 2.500 VDC until further adjustments are no longer required. Step 16 Inject on-frequency signal at a level of â80 dBm, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 2. Step 17 While monitoring the AC voltage at TP6 adjust audio 1 AC adjustment potentiometer (R71) for 350 mVRMS (Âą1 mV). Step 18 While monitoring the DC voltage at TP6 adjust audio 1 DC adjustment potentiometer (R58) for 2.500 VDC (Âą1 mV). The audio AC and DC adjustments are interactive, therefore continue adjusting R71 for 350 mVRMS and R58 for 2.500 VDC until further adjustments are no longer required. Step 19 Inject on-frequency signal at a level of â80 dBm, modulated with a 1 KHz test tone at Âą5.0 KHz deviation into Receiver 3. Step 20 While monitoring the AC voltage at TP6 adjust audio 1 AC adjustment potentiometer (R53) for 350 mVRMS (Âą1 mV). Step 21 While monitoring the DC voltage at TP6 adjust audio 1 DC adjustment potentiometer (R59) for 2.500 VDC (Âą1 mV). The audio AC and DC adjustments are interactive, therefore continue adjusting R53 for 350 mVRMS and R59 for 2.500 VDC until further adjustments are no longer required. Step 22 Adjust the carrier detect potentiometer (R74) to illuminate a level of â116 dBm. Receive Data Step 1 Using a calibrated mobile radio, generate uplink data messages using the X=1400,19 command in the IPMessage Utility program. Step 2 Attach an antenna to one of the base stationâs receiver ports and verify on the base station monitor screen (HyperTerminal) that the received message data quality are consistently 240 and higher for 1400 character messages. Repeat test for each receiver. 637246.DOC Page 23 SECTION 5: FACTORY TEST PROCEDURE Exciter Step 1 Using the X=1400,19 command, generate data messages so the transmit power and frequency can be checked. Step 2 Note the power level and then on the power amplifier circuit board adjust the potentiometer (R3) fully counterclockwise (this will enable low power transmit operation). Step 3 Connect the base stationsâ transmit port to the HP communication test set. Step 4 While transmitting data messages using the X=1400,19 command, adjust the following:  TCXO Y1 for minimum frequency error  R42 for Âą5 KHz deviation Transmit output power should be approximately 1mWatt. The REFMOD adjustment needs to be made while the base station is transmitting real data messages to and from a mobile radio. This is most easily done using the ping command to ping the IPNC from a mobile radio. This will cause the base station to repeatedly send data messages and will facilitate the REFMOD adjustment. Step 5 Connect the base station to the IPNC. Step 6 Using a calibrated mobile radio operating on the base stationâs channel, adjust R30 for consistent data quality readings of 248 (as observed on the mobile radioâs attached PC IPMessage window). Access the MSDOS prompt and ping using the following command: >;ping 192.168.3.3 ât âl 500 âw 2000 This command will ping the IPNC continuously with a 500-character test message. Press [Ctrl]+C to stop the ping. Power Amplifier Step 1 Connect the base stationâs transmit port to the communication test set. Step 2 Using the X=1400,19 command, generate data messages. Step 3 Slowly increase the base station output power by turning the power control potentiometer clockwise until the power noted in Step 2. Do not exceed 40 watts output power, as this will reduce the life of the amplifier module. If the base station uses a power amplifier, output power must be set to achieve power output specified for the specific base station installation. Step 4 Perform a close visual inspection of the base station paying close attention to manufacturing related problems such as loose screws, solder practices, etc. 637246.DOC Page 24 SECTION 6: FCC LABEL 16842 Von Karman Ave Suite 200, CA 92606 Model U.S. PATENT Nos. 5,640,695 MAC ID SN 6,018,647 6,243,393 Made in U.S.A B64450G25 Base Station FCC Label Placement B64450G25 Base Station FCC Label 637246.DOC Page 25 APPENDIX A: B64450G25 TEST DATA SHEET Program and Configure the Base Station Date Serial Number Firmware Revision End User Tester Adjustment / Alignment Procedures Receiver Injection Parameter Spec Injection Frequency Error at RXINJ1(within +/- 10 Hz of exact injection frequency) P1 & C39 Measured +/- 100 Hz 5 +/- 1 dBm Receiver Diversity Reception Controller 1, 2 & 3 Parameter Spec U6 Pin 4 +10 to +5 dBm RSSI Test Point TB1-4 2.8 to 3.0 VDC Distortion (1 kHz Test Tone @ 5.0 kHz) SINAD 12 dB (1 kHz Test Tone @ 5 kHz) SINAD +50 dB TP1 2.75 +/- 1 mV 637246.DOC Receiver 3 Measured -119dBm > 0.75 VDC +/- 1 mV Carrier Detect Light Set Receiver 2 Measured 3%< SINAD 12 dB TP1 Audio AC Amplitude (1 kHz Test Tone @ 5 kHz Deviation) Audio DC Amplitude (1 kHz Test Tone @ 5 kHz Deviation) Receiver 1 Measured 350 mVRMS +/- 1mV 2.5 VDC +/1 1mV -116 dBm Page 26 APPENDIX A: B64450G25 TEST DATA SHEET Data Quality Parameter Spec Receiver 1 Data Quality (x=1400, 19 Command IPMessage Utility) 240> Receiver 2 Data Quality (x=1400, 19 Command IPMessage Utility) 240> Receiver 3 Data Quality (x=1400, 19 Command IPMessage Utility) 240> Measured Exciter Parameter Spec Transmit Frequency Error (Transmitting 1400 character test message) Transmit Modulation Deviation (5.3 kHz while transmitting 1400 character test message) Transmit Data Quality (While transmitting 1400 character test message to the base station) Measured +/- 500 Hz 5.1 kHz to 5.3 kHz 240> Transmit Power Control Warning: Do Not exceed 40 Watts RF output power during this test Parameter Output Power (Use x=1400,19 command) Spec RF Out RF Out Max Level set to 40 +/- 1 Watt Test Check List Test Task Completed (9) Attached copy of Base Stationâs Firmware Settings Visual Inspection Copy Base Station Settings Below: 637246.DOC Page 27
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2006:03:16 17:34:43-05:00 Modify Date : 2006:03:16 17:34:43-05:00 Page Count : 27 Creation Date : 2006:03:16 22:34:43Z Mod Date : 2006:03:16 22:34:43Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : Administrator Metadata Date : 2006:03:16 22:34:43Z Creator : Administrator Title : Microsoft Word - 637246.DOCEXIF Metadata provided by EXIF.tools