IPS Technology HT-HS01 wifi doorbell User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3052524
Application ID	KrOl21n/FjVTQQ0HeOE+Mw==
Document Description	User Manual-revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	77.19kB (964860 bits)
Date Submitted	2016-07-06 00:00:00
Date Available	2016-07-07 00:00:00
Creation Date	2016-06-21 10:05:48
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-06-24 09:23:01
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 for Word
Document Author:	admin

Brief Instruction Manual
for EggBell
29/July/2015
1. Product Introduction & Description
1.1 Brief introduction
Accessories：
----EggBell
1 pcs
----Power adapter
----CD with software
1 pcs
1 pcs
----Instruction Manual
----Installation Package
----Bracket
1.2 Product description
1 pcs
1 pcs
1 pcs
1
WPS
Reset
PIR
SD slot
Came ra Lens
Microphone
IR cut
IR LED
10
11
12
13
14
15
16
Bell Button
Speaker
Indicator LED for video Recording
Indicator LED for Powe r
Indicator LED for Wifi
Waterproof Case
Anti-tampe r screw hole
battery compartment
17 Powe r port
(18650 batte ries, brand such as UltraFire)
18 Power s witch
Note：When EggBell is switched on, the default mode is ”Smart link” mode; Press once the
“WPS” key, it will enter into WPS mode, Press the “WPS” key continuously for 5 seconds, it
will enter into AP mode.
2. Installation
2.1 Installation of EggBell
Installation to replace the peep-hole on the door
1、 Remove the peep-hole
Remove the peep-hole from the door, and get the power cord through the hole,
just like the picture below：
2、 Connection of the power supply
Fix the small rod on the bracket with the hexagonal screw tighten，get the power cord through
the rod; Connect the power cord into the power port, just like the picture below：
Warning: Please use the standard AC adapter for the product,
in case that EggBell will be damaged.
3、Fix the Bracket
Screw on the four corners of the bracket fixed on the door with the accessories in the installation
package, and tighten the special anti-tamper screw on the bottom, plug in power source.
Installation on the wall
1 Drill the screw holes of which the location is matched with the four holes of the bracket, fix
the bracket on the wall with four screws;
2 Get the power cord connected with the power port through the hole on the back of the
bracket
2.2 Connection with mobile device
1. Download and install the P2P application”EggBell”
2. Search the Application ”EggBell” on application store , and download it on your phone (Android
users can get it from “Android Market”，or find and install the APP from the CD attached; iOS users
can download on App Store）。
3. Install the the application on your mobile phone and then run it, configure the Wifi of the device
under Smart Link mode (entering into Smart Link mode by default when EggBell is switched on).
Click the “Configure Device” — “Smart Mode” — Enter in the UID of EggBell UID
( Or scan the QR code to add the device）— Configuration WiFi
Note: During the process when configuring Wifi, the blue indicator LED on the right side will
flash frequently; After connected to Wifi, the bule LED will keep always on (like the picture
above), while there will be prompt tone “ding-dong” from the device to tell you configuring
successfully.
3、After WiFi Configuration, Click “Direct access” —Add Device—Add a networked
device.
Three ways to add device, all of them can add EggBell successsfully
Add automatically: Click “search in the LAN”, the UID of EggBell will be
automatically searched, then click Add.
Scan mode: Click the button to scan the QR code on EggBell, the red line need to be
aligned with
the QR code scanner, when hear a "beep", it tells scanning successfully, the scanner will
automatically put the serial number scanned in UID blank. Then enter in the User Name and Password
(They are both “admin” by default). Click the “Edit” on the top right corner, the device will
appear on the device list.
Manually：Click the "Add" icon, manually enter the serial number UID（UID serial number at
the bottom of the label on EggBell, mixed with letters and numbers). Then enter in the User Name and
Password (They are both “admin” by default). Click the “Edit” on the top right corner, the device
will appear on the device list.
4. The door bell will appear on the device list when added successfully. When click the “Edit” on the
top right corner, you can also reset the device name, the user name, the password, and delete the
device from the list, etc.
3.Function Introduction
3.1Push Function
After the door bell added successfully, admit ”Outdoor call-in”, the push function
will be available.
3.1.1 Push notification when press the bell button
When someone press the bell button, EggBell will start recording the video automatically for 20
seconds, and storing the video file in the TF card, at the same time it will push the message to the
APP on your phone with ringing tone. You could click to accept the call, then enter into the monitor
image to reach the function such as snapshot, record video, talk with the visitor, etc. Just like the
picture below:
3.1.2 Push notification for staying
When someone keep staying in front of EggBell for 20-30 seconds,EggBell will start recording the
video automatically for 20 seconds, and storing the video file in the TF card, at the same time it will
push the message to the APP on your phone with ringing tone. You could click to accept the call,
then enter into the monitor image to reach the function such as snapshot, record video, talk with
the visitor, etc. Just like the picture above.
3.2 Access to the files of recording and snapshot
3.2.1 Access to the local files on the phone for recording and snapshot
The files for snapshot manually and recording are stored locally on mobile phone，you can access to
them, and check the call logs on APP, just like the picture below:
3.2.2 Access to the files saved in the TF card for recording and snapshot
The files of snapshot and recording via Pressing button and Staying overtime are stored in the TF
card, you can access remotely to these files on APP, just like the files below:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
The statements should be displayed in the user manual:
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Endusers and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : admin
Create Date                     : 2016:06:21 10:05:48+08:00
Modify Date                     : 2016:06:24 09:23:01+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2016:06:24 09:23:01+08:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:779a2c02-df21-4a72-b263-605961b21b42
Instance ID                     : uuid:60b30b50-ce2a-477a-bfc0-3a3c0d79437d
Subject                         : 6
Format                          : application/pdf
Title                           : P2P网络摄像机简易使用手册
Creator                         : admin
Producer                        : Adobe PDF Library 11.0
Source Modified                 : D:20160608021259
Company                         : 微软中国
KSO Product Build Ver           : 2052-9.1.0.5132
Page Layout                     : OneColumn
Page Count                      : 13

EXIF Metadata provided by EXIF.tools