IR TEC HS1X0900 TRANS-HFD User Manual 058 10901 002 IM EN LMD 109

Download:
Mirror Download [FCC.gov]
Document ID	3870359
Application ID	gjxIsF5DJD20lMOs7SW9yA==
Document Description	User Manual (LMD-109).pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	90.85kB (1135657 bits)
Date Submitted	2018-05-31 00:00:00
Date Available	2018-05-31 00:00:00
Creation Date	2018-05-04 10:01:31
Producing Software	Adobe PDF library 10.01
Document Lastmod	2018-05-04 13:22:10
Document Title	058-10901-002_IM-EN_LMD-109
Document Creator	Adobe Illustrator CS6 (Windows)

OVERVIEW
LMD-109
Line Voltage Bi-Level Occupancy Sensor
INSTALLATION INSTRUCTIONS
APPLICATION NOTES
Avoid placing the sensor in an area surrounded with
metallic wall which may block or absorb the radio wave.
If possible, place the sensor to the opening as close as
possible.
The LMD-109 is a line voltage occupancy sensor designed for
OEM lighting fixture integration with 0-10V output for bi-level
dimming control. This occupancy sensor employs an
advanced High Frequency Doppler (HFD) sensing technology
to provide superior sensing performance of minor motion,
such as typing, writing, or reading. The HFD technology is
operating with high frequency radio waves which are capable
of detecting the occupant's presence and movements without
requiring unobstructed line-of-sight like a PIR sensor. Thus,
the HFD sensor can detect through non-metallic material,
such as plastic, glass, plywood or plaster board.
Fluorescent light may cause interference to the HFD
sensor operation, and result in lighting permanent on. If
possible, avoid placing the HFD sensor within 1m (3ft.)
of fluorescent light.
Avoid sensor placement facing doors, corridors or exits
as HFD sensor may detect the traffics at adjacent area.
The Accu-Set digitalized potentiometers make the sensor
setting easier, faster and more accurate than the conventional
analog ones. Four levels of sensitivity and control modes can
be selected via DIP switch setting. An exclusive Hybrid
Switching technology makes the LMD-109 perfect to control
lighting with exceptionally high inrush current (HIC) during
switching, such as multiple LED lightings connected in
parallel. The sensor comes with an ambient light sensor (ALS)
to inhibit switching on the light if the ambient light level is
higher than the threshold set.
The HFD sensor is more sensitive to the movements
“toward” than “across” the sensor, so ensure to place
the sensor at the position “toward” the movements of
occupant.
DETECTION PATTERN
DIMENSIONS
3.6mm
(0.14”)
Indoor dry location use only
Utilisation a L'interieur Uniquement
HFD sensors are best for use in areas with partitions and
high dividers, or high level of minor motion activities.
Mounting Height
Coverage*
*Sensitivity 100%
3 m (10 ft)
180 m2 (2,000 ft2)
(m)
Minor motion
6 m (20 ft)
100 m2 (1,200 ft2)
CAUTION
Risk of Electric Shock - Disconnect power supply before
servicing.
Open Type Photoelectric Switches.
Install the sensor at least 1ft. away from any occupant.
LMD-109
92mm
(3.6”)
84mm
(3.3”)
PRUDENCE
Risque de choc électrique - Débranchez l'alimentation avant
l'entretien.
Ouvrir Type commutateurs optoélectroniques.
43mm
(1.69”)
IR-TEC hereby declares that the LMD-109 complies with Directive 2014/53/EU issued by the Commission of the
European Community. The complete declaration of conformity is available on our website: www.irtec.com
Major motion
(ft)
10
29mm
(1.69”)
30
20
10
20
20
9 (m)
30 (ft)
The frequency and maximum transmitted power in EU are listed as 5800 MHz: -11.28dBm.
Federal Communication Commission Interference Statement
FCC ID：NRIHS1X0900
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
www.irtec.com
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
P/N: 058-10901-002
Printed in Taiwan
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
Industry Canada statement:
IC:
22993-X09HS1AC602
IC ID：22993-X09HS1AC602
This device complies with ISED’s licence-exempt RSSs. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable,
et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
IR-TEC International Ltd.
6 Rong An Road
Luzhu Taoyuan 338
TAIWAN
IR-TEC America, Inc.
590 W. Central Avenue Suite C
Brea, CA 92821
USA
Radiation Exposure Statement:
This equipment complies with ISED radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with minimum distance 20cm between the
radiator & your body.
Déclaration d'exposition aux radiations:Cet
équipement est conforme aux limites d'exposition aux
rayonnements ISED établies pour un environnement
non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la
source de rayonnement et votre corps.
Sensitivity - SW1 & 2
WIRING DIAGRAM
DIM
DIM
BALLAST
LED DRIVER
Neutral
LMD-109
DIM N
Gray
Violet
White
Red
Black
Line
NOTE:
1. The driver/ballast MUST be 0-10V dimmable to achieve
dimming control.
2. Ensure connection of LINE and NEUTRAL are not reversed
to avoid damaging the sensor.
3. Ensure TOTAL isolation between DIM+/DIM- and GROUND
to avoid damaging the sensor.
4. Conduct test with GROUND connected.
SENSOR SETTINGS
N N
The LMD-109 features 4 different control modes selectable via
combination DIP switch #3 and #4, and 4 levels of sensitivity
LMD-109
set via combination DIP switch #1 and #2. The LMD-109 also
provides 7 different light-Off delay time and daylight threshold
settings via 2 Accu-Set digital potentiometers marked T and L
respectively.
POS. 1
TIME TEST 1
LUX 5 10
Position
T (min.)
L (lux)
5 10 20 30
20 25 60 24H
SW1 & 2 (100% Sensitivity)
SW3 & 4 (OSLATO Mode)
30’
T*
1’
3’
5’
10’
20’
10
15
20
25
60 24H
Factory Set
T - Delay Time
The potentiometer T sets the period of delay time that sensor
will turn off the connected lights after the area is vacated.
L - Ambient Light Level
100%
75%
DIP switch
setting
ON
ON
The potentiometer L sets the ambient light level that the
sensor will activate occupancy sensing control.
ON-ON
50%
ON
ON-OFF
To verify sensor control function normal, please proceed
with the instructions as below to conduct test;
1. Set the arrow of T (DELAY TIME) potentiometer pointing
at position "1" (TEST) and other setting to the desired
threshold.
25%
ON
OFF-ON
OFF-OFF
Control Mode - SW3 & 4
The combination of DIP switch #3 and #4 determines the
sensing control mode.
OSLATO
OSLA
OSO
ON/OFF
Mode
OSLATO
ON-ON
(10 minutes)
(Factory set)
Sensitivity
ON
TIME
(Factory set)
ON
LUX
(ALS disabled)
15
TESTING
The sensitivity and detection pattern of HFD sensor
may vary with the furniture placement, partition layout,
wall material, and shape of the space. For example, the
detection pattern will become long rectangular if sensor is
placed in a long corridor. 4 levels of sensitivity can be set
via combinations of DIP switch #1 and #2.
OSLA
ON
ON-OFF
OSO
ON
OFF-ON
ON/OFF
ON
OFF-OFF
: Occupancy Sensing at Low Ambient with Time-Off
: Occupancy Sensing at Low Ambient
: Occupancy Sensing Only
: ON-OFF Switching
Control (LMD-109)
1. While ambient lux is higher than the level set, light
stays OFF.
2. While ambient lux is lower than the level set, and
occupancy detected, switch the light ON.
3. Dim the light to 30% after occupant leave and delay
time elapses.
4. Turn OFF the lights when 10 minutes TIME OFF
delay elapses.
5. When occupancy detected during TIME OFF,
switch the light ON.
1. While ambient lux is higher than the level set, light
stays OFF.
2. While ambient lux is lower than the level set, dim
the light to 30% under vacancy.
3. While ambient lux is lower than the level set, and
occupancy detected, switch the light ON.
4. Dim the light to 30% after occupant leave and delay
time elapses.
NOTE: Not applicable for fixture internal integration.
1. Ambient light is disabled with this mode.
2. Dim the light to 30% at all time under vacancy.
3. Switch the light to ON under occupancy.
4. Dim the light to 30% after occupant leave and delay
time elapses.
1. While ambient lux is higher than the level set, light
stays OFF.
2. While ambient lux is lower than the level set, and
occupancy detected, switch the light ON.
3. Turn OFF the light after occupant leave and delay
time elapses.
2. Walk within the expected range at normal speed. The
sensor will switch ON the light for 10 seconds whenever
sensor detects the movement, and then switch OFF or
DIM to 30% for 10 seconds as per the selected mode.
The LED of sensor will also blink to indicate every
motion detected.
3. After testing complete ensure to set the T potentiometer
to the position of desired time. NOTE: The sensor will
automatically control the light as per the selected mode
with factory set time delay (10 minutes) if the T
potentiometer has NOT been set to other position.
SPECIFICATIONS
Power supply
120/240/277VAC, 50/60 Hz
Maximum load
120VAC
240VAC
277VAC
-Incandescent/Halogen
800/*500W(VA)
5A
1200/*750W(VA)
-Fluorescent Ballast/CFL
800/*500W(VA)
5A
1200/*750W(VA)
-Ballast Electronic (LED)
540/*500VA
5A
1200/*750VA
HFD sensitivity
25/50/75/100% selectable via DIP switch setting
Load switching
Zero-cross Hybrid-Switching
HIC protection
Max. 80A for 16.7msec.
Dim control
0-10V, ±5%, non-isolated, max. 25 mA
Detection range
Up to 180 sq. m. @ 3 m (2,000 sq. ft @ 10 ft)
Mounting height
2.4 ~ 6 m (8 ~ 20 ft)
Ambient light level
7 level Accu-Set digital potentiometer
Delay time setting
T/1'/3'/5'/10'/20'/30' , T=10 sec. for testing
TIME OFF delay
10 min., OSLATO mode only
Op. humidity
Max. 95% RH
Op. temperature
-40°C~70°C (-40°F~158°F)
Dimensions
H92 x W43 x D29mm (H3.6"x W1.69"x D1.14")
*Max load for operating temperature at 55°C~70°C (131°F~158°F)
www.irtec.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : 058-10901-002_IM-EN_LMD-109
Creator Tool                    : Adobe Illustrator CS6 (Windows)
Create Date                     : 2018:05:04 10:01:31+09:00
Modify Date                     : 2018:05:04 13:22:10+08:00
Metadata Date                   : 2018:05:04 13:22:10+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 184
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 5273 bytes, use -b option to extract)
Document ID                     : xmp.did:D29A5AE8384FE8118521DC163049D5AE
Instance ID                     : uuid:d900dc15-ffc1-47f5-ac90-f81bef10633c
Original Document ID            : uuid:204986159B0AE111BDC19448B1A00566
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:84ee5871-8ceb-44d8-912e-d99299f7f445
Derived From Document ID        : xmp.did:1C7C70448143E8119E168B1DDD26F879
Derived From Original Document ID: uuid:204986159B0AE111BDC19448B1A00566
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:690747482FECE111A2868A1CFD8DCAE5, xmp.iid:D29A5AE8384FE8118521DC163049D5AE
History When                    : 2012:08:22 15:59:21+08:00, 2018:05:04 10:01:28+08:00
History Software Agent          : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows)
History Changed                 : /, /
Producer                        : Adobe PDF library 10.01
N Pages                         : 1
Has Visible Transparency        : True
Has Visible Overprint           : True
Max Page Size W                 : 29.699996
Max Page Size H                 : 20.999993
Max Page Size Unit              : Centimeters
Font Name                       : ArialMT, Humanist521BT-Bold, Swiss721BT-Bold, Swiss721BT-Roman, Txt, AdobeMingStd-Light
Font Family                     : Arial, Humanst521 BT, Swis721 BT, Swis721 BT, Txt, Adobe 明體 Std
Font Face                       : Regular, Bold, Bold, Roman, Regular, L
Font Type                       : Open Type, TrueType, Open Type, Open Type, TrueType, Open Type
Font Version                    : Version 6.98, mfgpctt-v1.52 Wednesday, January 13, 1993 4:39:52 pm (EST), Version 1.01 emb4-OT, Version 1.01 emb4-OT, Macromedia Fontographer 4.1.3 4/14/97, Version 6.008;PS 6.001;hotconv 1.0.67;makeotf.lib2.5.33168
Font Composite                  : False, False, False, False, False, False
Font File Name                  : arial.ttf, HUM521B_0.TTF, tt0005m_.ttf, tt0003m_.ttf, txt_____.ttf, AdobeMingStd-Light.otf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Group Name               : 預設色票群組
Swatch Group Type               : 0
Swatch Colorant Swatch Name     : 白色, 黑色, 炭筆色, 石墨色, 煙灰, 霧灰色, 拿鐵色, 卡布奇諾色, 摩卡奇諾色, 摩卡咖啡色, 火星紅, 紅寶石, 紅色, 南瓜黃, 潑濺, 陽光, 純黃色, 橄欖綠, 嫩芽綠, 翡翠色, 薄荷玫瑰露, 寶石綠, 海洋綠, 加勒比海藍, 純青色, 夏威夷藍, 昏黃藍, 星空藍, 深海藍, 亮淡紫色, 紫色, 水晶紫, 紫紅色, 純洋紅色, 整體紅色, 整體壓縮, 整體純黃色, 整體綠色, 整體純青色, 整體深海藍, New Color Swatch 2, New Color Swatch 10, New Color Swatch 3, New Color Swatch 7, New Color Swatch 6, AutoCAD Color, AutoCAD Color 2, AutoCAD Color 6, AutoCAD Color 3, AutoCAD Color 4
Swatch Colorant Mode            : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK
Swatch Colorant Type            : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS
Swatch Colorant Cyan            : 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 15.999996, 32.000000, 42.999996, 25.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 50.000000, 50.000000, 75.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 75.000000, 75.000000, 50.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 80.000000, 100.000000, 100.000000, 92.941200, 10.196100, 92.941200, 92.941200, 10.196100, 92.971703, 92.971703, 54.924797, 0.000000, 54.924797
Swatch Colorant Magenta         : 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 23.000002, 37.000000, 48.000000, 52.000000, 100.000000, 100.000000, 100.000000, 75.000000, 50.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 25.000000, 25.000000, 0.000000, 25.000000, 50.000000, 75.000000, 100.000000, 75.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 50.000000, 0.000000, 0.000000, 0.000000, 100.000000, 87.843102, 0.000000, 87.843102, 87.843102, 0.000000, 87.972801, 87.972801, 0.000000, 96.020401, 0.000000
Swatch Colorant Yellow          : 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 33.000000, 58.000000, 76.000000, 80.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 50.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 89.019600, 82.745102, 89.019600, 89.019600, 82.745102, 89.019600, 89.019600, 17.715700, 94.604401, 17.715700
Swatch Colorant Black           : 0.000000, 100.000000, 75.000000, 60.000004, 45.000000, 30.000002, 0.000000, 0.000000, 19.999998, 38.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 25.000000, 25.000000, 25.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 80.000000, 0.000000, 80.000000, 80.000000, 0.000000, 79.998497, 79.998497, 0.000000, 0.000000, 0.000000
Swatch Colorant Tint            : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000
Has XFA                         : No
Page Count                      : 2
Creator                         : Adobe Illustrator CS6 (Windows)

EXIF Metadata provided by EXIF.tools