IRay Technology 01070189 WiFi Module User Manual

iRay Technology Co. Ltd. WiFi Module Users Manual

User Manual

AI-Link WIFI-V897 Series IEEE 802.11 2X2 MIMO ac/a/b/g/n WiFi Features： ➢ Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac ➢ Chip Solution Marvell 88W8897 Model Standard Rate Channel POWER WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 866.7Mbps 2.4G/5G 5V Sichuan AI-Link Technology Co.,Ltd Add: Anzhou,Industrial park,Mianyang,Sichuan,China Fax : +86-0816-2416943 http://www.changhong.com
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 2 of 23 Record of Modification Feedback of customer’s Confirmation We accept the specification after Confirmed Customer name Customer signature Confirmation Date Please feed back this paper and first paper after your signature by the address,thanks! ADD： Anzhou,Industrial park,Mianyang,Sichuan,China Factory： Sichuan iLink Technology Co.,Ltd. Approved Checked Designed Product WiFi Module Bai lang Qian zijin Fan xijun Model WIFI-2-V897EA1 Date 2018-05-18
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 3 of 23 No Date of modification Main content of modification Reason of modification Serial number of modification Confirm 1 20180518 Confirmed for the first time Fan xijun
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 4 of 23 1. Introduction WIFI-2-V897EA1 is based on Marvell 88W8897,complied with IEEE 802.11a/b/g/n/ac. The Module is a highly integrated MAC/BBP and 2.4/5GHz RF/PA/LNA single chip which supports a 866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. ■ IEEE802.11ac (draft)compliant,2x2 MIMO spatial stream multiplexing with data rates up to MCS9(866.7Mbps) 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Marvell 88W8897. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11ac specification over SDIO,PCIE,USB and UART interface.. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. The 88w8897 provides a complete solution for a high throughput performance wireless client . . Figure 1 WIFI-2-V897EA1 Block Diagram
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 5 of 23 Note: Interface supports and combinations as shown below: Scenario WLAN Firmware Download I/F Firmware Download Mode Configuration* 1 PCIe PCIe Serial CON[3:0]=b'1110 NOTE: PCIe v3.0(2.5Gbps) interface USB 2.0 interface with LPM support 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 6 of 23 1.3 System Functions Table1: General Specification as below: Main Chipset Marvell 88W8897 Operating Frequency 2.4G/5G WiFi Standard 802.11a/b/g/n/ac(2x2) Modulation 11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM Data rates 11b:1, 2, 5.5 and 11Mbps 11a/g:6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps 11ac: MCS0~9, Nss=2, up to 866.7Mbps Form factor LGA Host Interface PCIE,USB PCB Stack 6-layers design Dimension Typical，30.0mmx 26.8mm Antenna External antenna Operation Temperature -20℃ to +50℃ Storage Temperature -20℃ to +50℃ Operation Voltage DC 3.3V , Interfaces PCIe interfaces support for WLAN Systems 1、 Drip-in WLAN Linux drivers are Android ready and validated on Android based systems. 2、Support for Linux kernel versions up to 2.6.32.
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 7 of 23 2. Mechanical Specification Typical Dimension (L x W): 30.0mmx 26.8mm Pin feet from left to right PIN Description PIN Description PIN Description 1 WAKEn 19 N.C 37 GND 2 VDD33 20 PCIE_DISABLE 38 USB_DP 3 GPIO0/CLK_REQ 21 GND 39 VDD3.3V 4 GND 22 PCIE_PERST 40 GND 5 WLAN_IRQ(O)/WAKE_UP 23 PCIE_TX_N 41 VDD3.3V 6 N.C 24 VDD3.3V 42 N.C 7 PCIE_CLKREQ_N 25 PCIE_TX_P 43 GND 8 N.C 26 GND 44 LED_WLAN 9 GND 27 GND 45 GPIO[10]/NFC_NOT_ALLOWED 10 N.C 28 N.C 46 LED_WPAN 11 PCIE_CLE_N 29 GND 47 GPIO[11]/NFC_ACTIVE 12 N.C 30 N.C 48 N.C 13 PCIE_CLK_P 31 PCIE_RX_N 49 N.C 14 N.C 32 N.C 50 GND 15 GND 33 PCIE_RX_P 51 PDN 16 N.C 34 GND 52 +3.3Vaux 17 N.C 35 GND 18 GND 36 USB_DM
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 8 of 23 Notes： 1. PCIE Impedance targets: Single-ended Z of 60 ohms +- 15% . Differential Impedance of ~100 ohm +- 20%. 2. USB Impedance targets: D+/D- are differential and should have 90ohms impedance. 3. Product Picture TOP VIEW BOTTOM VIEW
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 9 of 23 4. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (-20℃,+25℃,+50℃) and overall voltage (3.3V +/-15% ,). 4. 1 Absolute Maximum Ratings: Symbol Parameter Min. Typ. Max. Unit Remarks Pin73/ VIO Host I/O power supply - - - 1.8 2.5 3.3 2.2 3.0 4.0 V Pin44/ VIO_SD SDIO power supply - - 1.8 3.3 2.2 4.0 V Pin5/ 3V3_VBAT LDO VBAT input - 3.3 4.0 V Pin72/ 3V3_USB LDO USB VBAT input - 3.3 4.0 V Pin4/ 3V3_RF LDO RF VBAT input - 3.3 4.0 V 4. 2 Recommended Operating Conditions: Symbol Parameter Min. Typ. Max. Unit Remarks Pin73/ VIO 1.8V/2.5V/3.3V digital I/O power supply 1.62 2.25 2.97 1.8 2.5 3.3 1.98 2.75 3.63 V Pin44/ VIO_SD 1.8V/3.3V digital I/O SDIO power supply 1.62 2.97 1.8 3.3 1.98 3.63 V Pin5/ 3V3_VBAT LDO VBAT input 2.7 3.3 5.0 V Pin72/ 3V3_USB LDO USB VBAT input 2.97 3.3 3.63 V Pin4/ 3V3_RF LDO RF VBAT input 2.97 3.3 3.63 V
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 10 of 23 4. 3 IEEE 802.11a Section: Items Contents Specification IEEE802.11a Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH36 to CH165 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 13dBm Target (For Each antenna port) 12 - 14 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB 4. Frequency Error -20 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - - -84 dBm 2) 9Mbps (PER ≦10%) - - -83 dBm 3) 12Mbps (PER ≦10%) - - -81 dBm 4) 18Mbps (PER ≦10%) - - -79 dBm 5) 24Mbps (PER ≦10%) - - -76 dBm 6) 36Mbps (PER ≦10%) - - -72 dBm 7) 48Mbps (PER ≦10%) - - -68 dBm 8) 54Mbps (PER ≦10%) - - -67 dBm 6. Maximum Input Level (PER ≦10%) -30 dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 11 of 23 4.4 IEEE 802.11b Section: Items Contents Specification IEEE802.11b Mode DBPSK, DQPSK and CCK and DSSS Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated) 1) 13dBm Target (For Each antenna port) 11 - 14 dBm 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr 3. Constellation Error(EVM) @ Target Power 1) 1Mbps - - -10 dB 2) 2Mbps - - -10 dB 3) 5.5Mbps - - -10 dB 4) 11Mbps - -20 -10 dB 4. Frequency Error -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER ≦8%) - - -83 dBm 2) 2Mbps (FER ≦8%) - - -83 dBm 3) 5.5Mbps (FER ≦8%) - - -83 dBm 4) 11Mbps (FER ≦8%) - - -83 dBm 6. Maximum Input Level (FER ≦8%) -10 - - dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 12 of 23 4. 5 IEEE 802.11g Section: Items Contents Specification IEEE802.11g Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 13dBm Target (For Each antenna port) 10 - 14 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB 4. Frequency Error -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - - -89 dBm 2) 9Mbps (PER ≦10%) - - -87 dBm 3) 12Mbps (PER ≦10%) - - -86 dBm 4) 18Mbps (PER ≦10%) - - -84 dBm 5) 24Mbps (PER ≦10%) - - -81 dBm 6) 36Mbps (PER ≦10%) - - -77 dBm 7) 48Mbps (PER ≦10%) - - -73 dBm 8) 54Mbps (PER ≦10%) - - -72 dBm 6. Maximum Input Level (PER ≦10%) -30 dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 13 of 23 4.6 IEEE 802.11n HT20 Section: Items Contents Specification IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 2.4G CH36 to CH165 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 13dBm Target (For Each antenna port) @ 2.4G 10 - 14 dBm 2) 13dBm Target (For Each antenna port) @ 5G 10 - 14 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -10 - 10 ppm 2) IEEE802.11n HT20 @ 5G -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -85 dBm 2) MCS1 (PER ≦10%) - - -82 dBm 3) MCS2 (PER ≦10%) - - -80 dBm 4) MCS3 (PER ≦10%) - - -77 dBm 5) MCS4 (PER ≦10%) - - -73 dBm 6) MCS5 (PER ≦10%) - - -69 dBm 7) MCS6 (PER ≦10%) - - -68 dBm 8) MCS7 (PER ≦10%) - - -67 dBm 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 14 of 23 4.7 IEEE 802.11n HT40 Section: Items Contents Specification IEEE802.11n HT40 @ 2.4G IEEE802.11n HT40 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH3 to CH11 @ 2.4G CH38 to CH163 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 12dBm Target (For Each antenna port) @ 2.4G 10 - 13 dBm 2) 12dBm Target (For Each antenna port) @ 5G 10 - 13 dBm 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -10 - 10 ppm 2) IEEE802.11n HT20 @ 5G -12 - 12 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -82 dBm 2) MCS1 (PER ≦10%) - - -79 dBm 3) MCS2 (PER ≦10%) - - -77 dBm 4) MCS3 (PER ≦10%) - - -74 dBm 5) MCS4 (PER ≦10%) - - -70 dBm 6) MCS5 (PER ≦10%) - - -66 dBm 7) MCS6 (PER ≦10%) - - -65 dBm 8) MCS7 (PER ≦10%) - - -64 dBm 6. Maximum Input Level(PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 15 of 23 4.8 IEEE 802.11ac20/ac40 Section: Items Contents Specification IEEE802.11ac20/ac40 Mode BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM Channel CH42 to CH157 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 12dBm Target (For Each antenna port) 10 - 13 dBm 2. Spectrum Mask @ Target Power 10 - 13 1) at fc +/-11MHz /20MHz/30MHz - - -20 dBr 2) at fc +/-21MHz /40MHz/60MHz - - -28 dBr 3) at fc +/-41MHz /80MHz/120MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -27 dB 9) MCS8 -30 dB 10) MCS9 -32 dB 4. Frequency Error -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) VHT80 1) MCS0 (PER ≦10%) -76 dBm 2) MCS1 (PER ≦10%) -73 dBm 3) MCS2 (PER ≦10%) -71 dBm 4) MCS3 (PER ≦10%) -68 dBm 5) MCS4 (PER ≦10%) -65 dBm 6) MCS5 (PER ≦10%) -63 dBm 7) MCS6 (PER ≦10%) -61 dBm 8) MCS7 (PER ≦10%) -59 dBm 9) MCS8 (PER ≦10%) -56 dBm 10) MCS9 (PER ≦10%) -54 dBm 6. Maximum Input Level(PER ≦10%) -30 - - dBm
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 16 of 23 4.9 Clock Specifications Symbol Parameter Min. Typ. Max. Unit CLK Clock Frequency Range 32 or 32.768 -50ppm 32 or 32.768 32 or 32.768 +50ppm KHz THIGH Clock high time 40 - - ns TLOW Clock low time 40 - - ns TRISE Clock rise time - - 5 ns TFALL Clock fall time - - 5 ns 4.10 Reset Configuration WIFI-2-V897EA1 is reset to its default operating state under the following conditions:  Power-on reset (POR)  Software/Firmware reset  External pin reset (RESETn) 4.11Power up Timing Sequence
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 17 of 23 5. Interfaces 5.1.1 Host Interface
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 18 of 23 5.1.2 PCI Express Interface
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 19 of 23 5.2 PCI Express Interface 5.2.1 Interface Signal Description Symbol Parameter Min. Typ. Max. Unit UI Unit interval Each UI 400 ps±300 PPM UI does not account for SSC dictated variations 399.98 400- 400.12 ps VTX-DIFFpp Differential peak-to-peak output voltage VTX_DIFFpp=2*|VTX_D+ - VTX_D-| 0.8 - 1.2 V VTX-DE-RATIO De-emphasized differential output voltage(radio) -3.0 -3.5 -4.0 dB TRX-EYE Minimum Tx eye width 0.75 - - UI TRX-EYE-MEDIAN-_MAX-JIT Maximum time between jitter median and maximum deviation from median - - 0.125 UI TTX-RISE TTX-FALL D+/D- Tx output rise/fall time 0.125 - - UI TTX-CM-DC-ACTIVE-IDLE-DELTA Absolute delta of DC common mode voltage during L0 and electrical idle 0 - 100 mV TTX-CM-DC-LINE-DELTA Absolute delta of DC common mode voltage between D+ and D- 0 - 25 mV TTX-IDLE-DIFFp Electrical idle differential peak output voltage 0 - 20 mV TTX-RCV-DETECT Voltage change allowed during receiver detection - - 600 mV TTX-DC-CM Tx DC common mode voltage - - 3.6 V TTX-SHORT Tx short circuit current limit - - 90 mA TTX-IDLE-MIN Minimum time spent in electrical idle 50 - - UI TTX-IDLE-SET-TO-IDLE Maximum time to transition to a valid electrical idle after sending an electrical idle ordered set - - 20 UI TTX-IDLE-TO-DIFF-DTA Maximum time to transition to valid Tx specifications after leaving an electrical condition - - 20 UI RLTX-DIFF Differential return loss 10 - - dB RLTX-CM Common mode return loss 6 - - dB CTX AC coupling capacitor 7.5 - 200 nF TCrosstalk Crosstalk random timeout 0 - 1 ms
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 20 of 23 5.2.2 Differential Rx Output Electricals Symbol Parameter Min. Typ. Max. Unit UI Unit interval Each UI 400 ps±300 PPM UI does not account for SSC dictated variations 399.98 400- 400.12 ps VRX-DIFFpp Differential peak-to-peak output voltage VRX_DIFFpp=2*|VTX_D+ - VTX_D-| 0.175 - 1.2 V TRX-EYE Minimum Tx eye width 0.4 - - UI TRX-EYE-MEDIAN-_MAX-JIT Maximum time between jitter median and maximum deviation from median - - 0.3 UI VRX-CM-ACp AC peak common mode input voltage - - 150 mV RLRX-DIFF Differential return loss 10 - - dB RLRX-CM Common mode return loss 6 - - dB ZRX-DIFF-DC DC differential input impedance 80 100 120 Ω ZRX-DC DC input impedance 40 50 60 Ω ZRX-HIGH-IMP-DC-POS Powered down DC input impedance positive 50 - - k ZRX-HIGH-IMP-DC-NEG Powered down DC input impedance negative 1 - - kΩ VRX-IDLE-DET-DIFFpp Electrical idle detect threshold 65 - 175 UI TRX-IDLE-DET-DIFF-ENTERTIME Unexpected electrical idle enter detect threshold integration time - - 10 UI LRX-SKEW Total skew - -2 0 dB 5.3 USB Interface 5.3.1 USB 2.0 Device Interface Description Pin Name USB 2.0 Specification Pin Name Description Pin72/3V3_USB VBUS USB Bus Power Supply On-board regulator regulates voltage from VBUS level to voltage levels used by USB PHY GND USB Bus Ground Common ground on SoC device Pin70/USB_DP D+ USB Data Plus One of the differential data pair Pin69/USB_DM D- USB Data Minus One of the differential data pair
WIFI-2-V897EA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 21 of 23 ftware Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool version is ： MFG-W8897-MF-WIFI-BT-NFC-NO-CAL-BRG-FC-WIN-X86-2.1.0.76-15.2.7.p22
WIFI-2-V897USA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 22 of 23 7. Statement： FCC Radiation Exposure Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular be installed in any portable device, for example, USB dongle like transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display label referring to the enclosed module. This exterior label can use wording such as the following:” Contains Transmitter Module FCC ID: 2ACHK- V897EA1 Or Contains FCC ID: 2ACHK- V897EA1 when the module is installed inside another device, the user manual of this device must contain below warning statements;1. This device complies with Part 15 of the FCC Rules. Operation
WIFI-2-V897USA1 IEEE 802.11a/b/g/n/ac 2T2R Sichuan AI-Link Technology Co., Ltd. page 23 of 23 is subject to the following two conditions :(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device is intended only for OEM integrators under the followingconditions:1) The antenna must be installed such that 20 cm is maintained between the antenna and user.2) The transmitter module may not be co-located with any other transmitter or antenna. Module Antenna Type: For 2.4GHz : Antenna 0: 1.8dBi, Antenna 1: 2.4dBi For 5GHz: Antenna 0: 6dBi, Antenna 1: 6dBi

User_Manual

Navigation menu