Iconnect 96 4G LTE USB Dongle User Manual Onyx4G LTE USB Modem User s Manual 20170302

Download:
Mirror Download [FCC.gov]
Document ID	3476957
Application ID	NwhXip4lQ34ASXDfi0wxTQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	86.6kB (1082462 bits)
Date Submitted	2017-07-21 00:00:00
Date Available	2017-07-21 00:00:00
Creation Date	2017-05-15 11:46:27
Producing Software	Adobe PDF library 15.00
Document Lastmod	2017-07-21 16:04:41
Document Title	Onyx4G LTE USB Modem User's Manual 20170302
Document Creator	Adobe Illustrator CC 2017 (Windows)(Foxit Advanced PDF Editor)

4G LTE USB Dongle
● PIN code se�ngs
“Se�ng”->“PIN” menu is used to enable/disable, change, modify and unlock locked PIN
code via PUK. When inser�ng a PIN-enabled SIM card, modem will be prompt for PIN code
before using it. If the PIN codes were modified, please unplug/replug modem. The modem
u�lity will prompt for the new PIN code.
< NOTE >
A�er three failed a�empts to enter the PIN code, the SIM card will be locked. To unlock the SIM
card, you will be required to enter the correct PUK to retrieve the default PIN code. Please
contact your service provider to obtain the PUK code informa�on. With incorrect PIN code
input, the modem is unable to register on the network; All network service will be unavailable.
User’s Manual
HARDWARE INSTALLATION
Insert SIM Card Before Using Onyx4G
Slide off the cover on the back of the device.
Insert SIM card as shown in the diagram below.
< Op�onal > microSD card installa�on:
Onyx4G provides a microSD slot for file sharing feature.
To install a microSD card, please upturn the card and insert
it into the card slot as shown in the diagram. A "click" sound
indicates the card is installed properly. (Push the microSD
card again, it will be ejected from the memory card slot.)
Install Onyx4G to Your Computer
Onyx4G is powered by USB host port, and designed to work with
USB 2.0/3.0 port on your computer. To start using Onyx4G,
insert Onyx4G into an available USB port on your computer.
● Reset modem
“Se�ngs”->“Reset” menu is used to restore the device to factory default se�ngs and
reboot the device.
< NOTE >
If the computer does not have Onyx4G drivers installed, Onyx4G will prepare the u�lity program
installa�on.
If the u�lity program is already installed, Onyx4G will be detected, and u�lity program will start
automa�cally.
SOFTWARE INSTALLATION
Addi�onal Informa�on
This product is suitable for indoor network access applica�ons, not applicable for outdoor
usage. For up-to-date product informa�on, descrip�ons, documenta�on, applica�on
updates, and support informa�on, please visit www.alfa.com.tw
Install Onyx4G U�lity Program
Onyx4G contains the necessary drivers for Windows 7/8/10
computer ; an installa�on CD is not required. The first �me
connec�ng Onyx4G to a Windows computer, Onyx4G u�lity
program will start the u�lity program installa�on automa�cally.
Please permit the program installa�on if there is a prompt
window during the installa�on. Follow the on-screen instruc�ons
to complete the setup of the Onyx4G u�lity program.
< NOTE >
● If the installa�on does not start automa�cally, please turn on the CD Auto Run feature in your
computer or manually browse the new CD-ROM drive added by Onyx4G in "My Computer",
the setup.exe file of Onyx4G program can be found in the CD-ROM drive.
● Manual installa�on: Double-click the "Setup.exe" file and follow the on-screen instruc�ons to
complete the Installa�on. (Please permit the program installa�on if there is any prompt
message during the installa�on process.)
Start Using Onyx4G
Make sure Onyx4G is inside a network coverage area. On your computer’s desktop,
double-click the icon
to launch the Onyx4G connec�on program.
Onyx4G Program Home Page
< NOTE >
When using Onyx4G with a PIN-enabled SIM card,
each �me at program launch, it will be required
to input proper PIN code to use Onyx4G. If the
PIN-code is incorrectly input three �mes, SIM will
be locked. To unlock a locked SIM card, a PUK
code is required. The PUK code can be obtained
from the service provider. (When asking for PUK
code, please contact your service provider to
verify you are the owner of the SIM card.)
Onyx4G Program Feature Introduc�on
Sta�s�cs
Users can view present network transfer rates, the data used in total and the connec�on
�me. Sta�s�cs listed in this menu will be reset a�er the modem is unplugged.
< NOTE >
Download data is shown in red, and upload data is shown
in yellow.
Records
Users can review accumulated overall usage over �me, including network access dura�on
and the total network data transferred (in kilobytes) in a month or a selected �me.
USSD
You can add, edit, delete, and send USSD codes. The result of USSD codes submi�ed will be
displayed on the edit box.
< NOTE >
Unstructured Supplementary Service Data (USSD), is a protocol used by GSM cellular devices to
communicate with the service provider's equipment. USSD service is carrier-specific and o�en can
be used by prepaid GSM cellular customers to query their available balance, etc. Before using the
USSD feature, please consult your carrier to make sure USSD service is available, and informa�on
of the supported USSD codes.
SETTINGS
The “Se�ng”->“Network” menu is used to select or setup network access parameters and
priority of subscribed network services. Our modem u�lity includes preset parameters of
major carriers around the world. Please select a suitable connec�on parameter profile from
the drop-down list before a�emp�ng to connect to the Internet.
< NOTE >
The default connec�on profile is Chunghwa
Telecom (located in Taiwan).
Various network opera�on modes can be
selected. The default is Auto, but GPRS
only, or LTE only can be selected.
A�er selec�ng the opera�on mode, the
modem will register to chosen network
according to the selected mode.
If you cannot find a carrier connec�on profile from the drop-down list, you will need to
create a new one matching your subscribed data plan. Please consult your carrier to obtain
the connec�on parameters, and click the "New" bu�on to add new network connec�on
parameters to the Onyx4G u�lity program.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Note: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
SAR tests are conducted using standard operating positions accepted
by the FCC with the device transmitting at its highest certified power
level in all tested frequency bands, although the SAR is determined
at the highest certified power level, the actual SAR level of the
device while operating can be well below the maximum value, in
general, the closer you are to a wireless base station antenna, the
lower the power output.
Before a new device is a available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the exposure
limit established by the FCC, Tests for each device are performed in
positions and locations as required by the FCC.
For body worn operation, this device has been tested and meets the
FCC RF exposure guidelines when used with an accessory
designated for this product or when used with an accessory that
contains no metal and that positions the device a minimum of 5
mm from the body.
Non-compliance with the above restrictions may result in violation of
RF exposure guidelines.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2017:05:15 11:46:27+09:00
Creator                         : Adobe Illustrator CC 2017 (Windows)(Foxit Advanced PDF Editor)
Modify Date                     : 2017:07:21 16:04:41-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : Onyx4G LTE USB Modem User's Manual 20170302
Metadata Date                   : 2017:07:21 16:04:41-07:00
Creator Tool                    : Adobe Illustrator CC 2017 (Windows)(Foxit Advanced PDF Editor)
Thumbnail Width                 : 256
Thumbnail Height                : 68
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 9116 bytes, use -b option to extract)
Instance ID                     : uuid:e2dfe21c-3ef2-4359-a3f7-9533cfb6018a
Document ID                     : xmp.did:1518fe16-155e-454a-8468-8b494205de30
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Version ID                      : 1
Derived From Instance ID        : uuid:6ed1aa51-3254-407a-bf9d-f5239a5efb8a
Derived From Document ID        : xmp.did:24e05fca-d60b-9f42-b83a-7af56efa1133
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:3ac5ce68-4368-a348-bd96-4afebf2644cd, xmp.iid:1518fe16-155e-454a-8468-8b494205de30
History When                    : 2017:02:16 14:09:09+08:00, 2017:05:15 11:46:18+08:00
History Software Agent          : Adobe Illustrator CC 2017 (Windows), Adobe Illustrator CC 2017 (Windows)
History Changed                 : /, /
Startup Profile                 : Print
Has Visible Overprint           : False
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 209.999997
Max Page Size H                 : 130.000004
Max Page Size Unit              : Millimeters
Font Name                       : Calibri-Bold, Calibri-BoldItalic, Calibri
Font Family                     : Calibri, Calibri, Calibri
Font Face                       : Bold, Bold Italic, Regular
Font Type                       : Open Type, Open Type, Open Type
Font Version                    : Version 6.18, Version 6.18, Version 6.19
Font Composite                  : False, False, False
Font File Name                  : calibrib.ttf, calibriz.ttf, calibri.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : 明亮
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000000
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003100
Swatch Groups Colorants Black   : 0.003100
Producer                        : Adobe PDF library 15.00
Trapped                         : False
Creator Version                 : 21.0.0
ICN App Name                    : Foxit Advanced PDF Editor
ICN App Platform                : Windows
ICN App Version                 : 3.10
GTS PDFX Version                : PDF/X-4
Page Count                      : 3

EXIF Metadata provided by EXIF.tools