Identec Solutions ILR-IQ350LM UHF Tag User Manual i Q350L M Hardware Manual

Identec Solutions AG UHF Tag i Q350L M Hardware Manual

User Manual

i-Q350L M, Microtag Manual
Microtag ManualPage 2 of 11Proprietary NoticeThis document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used ordisclosed to other parties in whole or in part without prior written authorization from IDENTEC SOLUTIONS.Disclaimer and Limitation of LiabilityIDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents provide theinformation contained in this Manual on an “as-is” basis and do not make any express or implied warranties orrepresentations with respect to such information including, without limitation, warranties as to non-infringement, reliability, fitness for a particular purpose, usefulness, completeness, accuracy or up-to-dateness.IDENTEC SOLUTIONS shall not in any circumstances be liable to any person for any special, incidental, indirector consequential damages, including without limitation, damages resulting from use of or reliance oninformation presented herein, or loss of profits or revenues or costs of replacement goods, even if informed inadvance of the possibility of such damages.Trademarks“IDENTEC SOLUTIONS”, “Intelligent Long Range”, “ILR” and the stylized “i” are registered trademarks and“i-Q”, “i-D”, “i-B”, “i-CARD”, “i-PORT”, “i-LINKS”, “Solutions. It’s in our name.”, “Smarten up your assets” aretrademarks of IDENTEC SOLUTIONS, Inc. and/or IDENTEC SOLUTIONS AG.Copyright NoticeCopyright © 2007 IDENTEC SOLUTIONS. All rights reserved.No part of this document may be reproduced or transmitted in any form by any means, photographic,electronic, mechanical or otherwise, or used in any information storage and retrieval system, without the priorwritten permission of IDENTEC SOLUTIONS.Issue 0 / December 2009– 16. December 2009 –IDENTEC SOLUTIONS AG,Millenium Park 2, 6890 Lustenau, AustriaPhone: +43 5577 87387- 0, Fax: +43 5577 87387-15E-Mail: info@identecsolutions.atwww.identecsolutions.comSubject to alteration without prior notice.© Copyright IDENTEC SOLUTIONS 2009
i-Q350L MPage 3 of 11Radio Frequency Compliance StatementIDENTEC SOLUTIONS is the responsible party for the compliance of the following devices:MODELS: i-Q350L MRegion/Country Organization MarkingEUROPE EC CEUSA FCC FFC ID 004-ILR-IQ350LMCanada Industry Canada IC: 3538A-IQ350LMThe user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, byIDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTECSOLUTIONS, or any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.European Notification according R&TTE DirectiveThis equipment complies to Art. 6.4 of R&TTE Directive (1999/5/EC). It is tested for compliance with thefollowing standards: ETSI EN 300 220, ETSI EN 301 489, EN 60950USA NotificationThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, byIDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTECSOLUTIONS, or any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.
Microtag ManualPage 4 of 11Contents1 INTRODUCTION............................................................................................................51.1 PREPARATIONS....................................................................................................................51.2 RECOMMENDED PROCEDURE....................................................................................................51.3 SCOPE OF THIS DOCUMENT.....................................................................................................51.4 RESPONSIBILITY...................................................................................................................51.5 ASSOCIATED DOCUMENTS.......................................................................................................51.6 SCOPE OF DELIVERY—VISUAL INSPECTION.................................................................................52 SAFETY PRECAUTIONS .................................................................................................63 INITIAL OPERATION ....................................................................................................83.1 CONFIGURATION OF THE TAG..................................................................................................83.2 TAG HANDLING....................................................................................................................84 MAINTENANCE..............................................................................................................94.1 GENERAL............................................................................................................................94.2 PRECAUTIONARY MAINTENANCE...............................................................................................94.3 RETURNS............................................................................................................................95 TECHNICAL DATA .......................................................................................................10
i-Q350L MPage 5 of 111 Introduction1.1 PreparationsThis installation manual must be read carefully prior to starting the installation. The described installationworks assume that installation materials like cable, antenna and tag holder etc are available.1.2 Recommended Procedure1. Check the Scope of Delivery according to the Bill of Delivery2. Read this manual completely3. Do the initial operation for every single tag4. Mount the tags5. An additional performance check of the tags and a system test can now be done1.3 Scope of this DocumentThis document is the user’s manual of the model i-Q350L M.This document is intended only for mechanical installation rsp. everyday use.1.4 ResponsibilityIDENTEC SOLUTIONS is not responsible for any errors occurring in this document.1.5 Associated Documents• i-Q350L M — ILR350 Microtag Datasheet1.6 Scope of Delivery—Visual InspectionCheck delivery whether it is complete and for any damages. If the delivery is not complete or damagedimmediately inform the carrier. The dispatch and service organization of IDENTEC SOLUTIONS should also beinformed to facilitate the repair or exchange of the system.
Microtag ManualPage 6 of 112 Safety PrecautionsImportant Safety NoteThe devices described in this manual is for exclusive operation by trained employees. Only qualified personnelthat know the potential dangers involved should perform the installation, settings, maintenance and repair ofthe units used.Operational SafetyThe correct and safe use of these systems assumes that operating and service personnel follow the safetymeasures described in the manual alongside the generally acceptable safety procedures.If there is a possibility that safe operation cannot be guaranteed the system must be switched off and securedagainst accidental use. Then the service unit responsible must be informed.Do not open the housingThere is no need to open the housing. There are no user serviceable parts inside. Set-up and configurationduring initial operation is done wireless with the built-in air interface.Handling SafetyOn account of high operating temperature of 70 °C (+158 °F) care must be taken, if the tags are heated. Toavoid burn wait a while until the tags have cooled down or use gloves. At temperatures below 0 °C (+32 °F)tags can be iced. In this case, wait a while until tags are warmed up or use gloves.Battery InsideAll tags contain a battery. That is the reason for the following instructions:WarningFire, explosion and burn hazardRisk of explosion if battery is replaced by an incorrect typeDo not recharge, short circuit, crush, disassemble, heat above 70 °C (158 °F)Do not incinerate, or expose contents to waterElectrostatic DischargeThis product contains components that are sensitive to electrostatic discharges. Please observethe special instructions for their protection. Incorrect handling can damage the unit and cause theinvalidation of the warranty.Safety DocumentsThis ILR system was designed, tested and supplied in perfect condition according to document test reportEN60950.Condensation/Change of TemperatureMoving the systems from a cold to a warm environment could lead to dangerous situations due tocondensation. Therefore it must be ensured that the system can adjust itself to the warmer temperature.
i-Q350L MPage 7 of 11Spare PartsWe recommend that only original products, spare and replacement parts authorized by IDENTEC SOLUTIONSbe used for installation, service and repair. Otherwise IDENTEC SOLUTIONS does not accept any responsibilityfor materials used, work carried out or possible consequences.
Microtag ManualPage 8 of 113 Initial Operation3.1 Configuration of The TagImportant NoteDo not open the housing! Configuration is done using the built-in air interface of the i-Q350L M.ConfigurationThe i-Q350L M is configured according to the specific application by the custom-specific host software.Things to be configured• The ping rate: from 0.5 to 300 seconds in steps of 0.5 seconds• The number of bursts: from 0 to 15 (factory default setting: 5)• Broadcast Telegram Mode:- ILR B2 (ASK) compatible with i-PORT MB, i-CARD CFB- ILR 350 (FSK) compatible with i-PORT M 350, i-CARD CF 3503.2 Tag HandlingThe i-Q350L M is intended to be worn by individuals.With its hook it can be fixed to clothing with snap-fastener straps or Velcro straps e.g. to a buttonhole.The following picture gives an impression of the convenient size of the tag.
i-Q350L MPage 9 of 114 Maintenance4.1 GeneralIn principle, the ILR system is maintenance-free. When correctly installed it operates for many years withoutany problems.4.2 Precautionary MaintenanceRegular checking to the system is recommended. Make sure that the housing of the tag has no damage. Ifthere are any damages as holes or cracks, the tags should be replaced and returned to IDENTECSOLUTIONS immediately.Regular checking of all ports and cables belonging to the system is recommended. Unstable connections couldlead to damage and malfunctions of the system and therefore should be repaired as soon as possible.A Brief Checklist• Are all housings intact?• Are all cables intact?• Are all connectors intact?• Are all connectors securely fastened?• Are all screws still tight?• Is there suddenly a malfunction at a specific unit?4.3 ReturnsParts or main components returned for repair or exchange must be handled with great care. PC cards must bereturned in the appropriate ESD-protecting packaging material.All returns should include a completed returns form (see appendix) and be sent to the local distributor or to:IDENTEC SOLUTIONS AGService DepartmentMillenium Park 26890 LustenauAUSTRIA / AUTRICHE
Microtag ManualPage 10 of 115 Technical DataOperating DataOperating frequency ILR-RFID 868 MHz (EU) or 920 MHz (NA), further frequencies on requestTransmission power 0.75mW (EU / NA)Compatibility depending on Broadcast Telegram Mode:- ILR B2 (ASK) compatible with i-PORT MB, i-CARD CFB- ILR 350 (FSK) compatible with i-PORT M 350, i-CARD CF 350Standards/Certification FCC Part 15 (US), ETSI EN 300 220 (EU)Communication Data Long-Range RFID (ILR, Response Technology)Multiple tag handling Up to 2,000 tags in the read zoneRead/write range response mode Up to 10 m (30 feet), free air*Data rate response 19.2 to 115.2 kbits/sCommunication Data Long-Range RFID (ILR, Beacon Technology)Read range broadcast Up to 150 m (500 feet) free air*Operation mode Transmits marker information in at regular intervalsRepetition rate (ping rate) 0,5 – 300 seconds, adjustable in steps of 0,5 secondsData rate broadcast 115.2 kbits/s * The communication range depends on the antenna type, the antenna cable runs and theenvironmental conditions.Communication Data Inductive Loop (Marker)Read range Up to several metersOperating frequency 125 kHz (world-wide approved)Operation mode Receives marker ID number and transmits marker information severaltimesElectrical DataPower supply Lithium batteryConfigurationPing rate Configurable from 0.5 to 300 secondsin steps of 0.5 secondsNumber of Bursts Configurable from 0 to 15Environmental ConditionsOperating temperature –30 to +70 °C (–22 to +158 °F)Shock 50 G, 3 times acc. DIN IEC 68-2-27several times onto concrete floor from 1 m heightVibration 3 G, 20 sine wave cycles, 5 to 150 Hz,DIN IEC 68-2-65 G, noise 5 to 1.000 Hz, 30 minutesDIN IEC 68-2-64
i-Q350L MPage 11 of 11Mechanical DataDimensions 56 mm × 30 mm × 14 mmCasing PlasticsMass 40 gProtection class IP 65CertificationsEMC CE (EN 300 220-1, -3; ETSI EN 301 489-1, -3),FCC Part 15 (US), Industry Canada

Navigation menu