Identiv CLOUD4000F-001 Dual Interface Smart Card Reader Module User Manual

Identiv, Inc Dual Interface Smart Card Reader Module Users Manual

Users Manual

Identive Cloud 4000 F DTC – User Manual
Version: 1.0 Page 1 of 5
User manual
For
Identive Cloud 4000 F DTC
Version 1.0
Author Sudhan
Version 1.0
Date 28-August-2013
Identive Cloud 4000 F DTC – User Manual
Version: 1.0 Page 2 of 5
Document History
Version Date Description of Change Author
1.0 29-August-13 Initial version Sudhan
Identive Cloud 4000 F DTC – User Manual
Version: 1.0 Page 3 of 5
Table of Contents
1Scope of the document ..................................................................................................... 4
2About Identive Cloud 4000 F DTC reader ......................................................................... 4
3Driver Installation in Windows ........................................................................................... 4
4Communication with Card ................................................................................................. 4
5Certifications ..................................................................................................................... 5
FCC ..................................................................................................................................... 5
IC ......................................................................................................................................... 5
Identive Cloud 4000 F DTC – User Manual
Version: 1.0 Page 4 of 5
1 Scope of the document
The user manual specifies the basic application of the reader by the customer.
2 About Identive Cloud 4000 F DTC reader
Identive Cloud 4000 F DTC is a USB based dual interface reader capable of reading ISO7816
Contact smart cards and ISO14443 Contactless cards. The reader connects to a host PC via USB 2.0
Full speed interface.
3 Driver Installation in Windows
Follow the sequence of steps to install the driver
Plug in the reader to a Windows PC
The PC prompts for a driver
Select Microsoft CCID driver and install the driver
The device enumerates with Identive VID and PID strings
4 Communication with Card
Follow the sequence of steps to communicate with the contact card,
Plug in the reader to a Windows PC and load the driver
Launch the PCSCDIAG Utility
Insert the contact card into the card slot of the reader
Check the ATR of the card being displayed in the PCSCDIAG Utility
Follow the sequence of steps to communicate with the contactless card,
Plug in the reader to a Windows PC and load the driver
Launch the PCSCDIAG utility
Place a contactless card on top of the reader
Check the ATR of the card being displayed in the PCSCDIAG Utility.
Identive Cloud 4000 F DTC – User Manual
Version: 1.0 Page 5 of 5
5 Certifications
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Information to user
Changes or modifications not expressly approved by Identive could void the user's authority
to operate the equipment.
IC
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement

Navigation menu