Identiv PAT11211000 Physical Access Terminal User Manual PAT111 Installation Manual

Identiv, Inc Physical Access Terminal PAT111 Installation Manual

Contents

Users Manual 1111

PAT 1111 Installation Manual Rev 1.0 31st Aug 2005 PAT 1111 Installation Manual Page 1 of 6
PAT 1111 Installation Manual Page 2 of 6 Package Details • PAT 1111 • Mounting plate and screws • Test card (contactless) • Installation manual Recommendations • Cable, 10 conductor (Wiegand/Magstripe), 22GA Shielded, Upto 150 mtrs, Line Resistance 2.5 ohms • Cable, 8 conductor (RS485), 22AWG twisted pair, Upto 4000 feet • Regulated DC power supply unit Specifications Host Interface • Wiegand/Magstripe (CLK/Data) • RS485 (2 or 4 wires) • 3 relay inputs to set reader state SAM • ISO 7816 1-3 • T=0, T=1 protocol support (5V card) • Communication speed up to 344,086 bps Contactless • ISO 14443 Type A and B (13.56 MHz) • Supports ISO 14443 part 1 to 4 • Operating distance: 1 inch • Communication speed: 106 Kbps • Internal 3DES for card authentication (DESFire) Human Interface • 1 LED beam (green and red) for access information (granted and denied) • 1 LED for contactless card access • Buzzer for user acoustic feedback Application • Full SDK (software development kit) available • Field Secure firmware upgrade Dimensions • LWH 148 84 46 mm Power • 10V to 16V DC – 200mA Approvals • FCC, UL 294, CE
Installation Instructions • Fix the mounting plate in an appropriate position on the wall, where the cable can be easily connected to the back of the reader. • Place the reader on the mounting plate and fix it by using mounting screw. This is shown in the picture below. Unit Mounting plate Connector Male - female Screw Cable PAT 1111 Installation Manual Page 3 of 6
Mounting plate details Fig 1.1 Mounting plate (Horizontal view) Fig 1.2 Mounting plate (Normal view) Fig 1.3 Mounting plate (Vertical view) PAT 1111 Installation Manual Page 4 of 6
Connector details Connector details for Wiegand/Magstripe – 10pin Terminal Block Pin Number Signal Name 1 Relay IN1 2 Relay IN2 3 Relay IN3 4 Relay GND 5 Wiegand Data0 / Mag Data 6 Wiegand Data1 / Mag CLK 7 Wiegand LED IN 8 Wiegand Buzzer IN 9 Wiegand GND 10 Wiegand +12V Connector details for RS485 – 8pin Terminal Block Pin Number Signal Name (Full Duplex Operation ) Signal Name (Half Duplex Operation) 1 RX_A RX/TX_A 2 RX_B RX/TX_B 3 TX_A No connection 4 TX_B No connection 5 RS485 GND RS485 GND 6 SHIELD SHIELD 7 Power +12V Power +12V 8 Power GND Power GND A – Non-inverted RS485 differential signal; B – Inverted RS485 differential signal Configuration details for RS485 DIP switch - 8 position, Termination & Biasing Selection Switch. Full Duplex RS485 Half Duplex RS485 Switch Position With Termination and Biasing OFF With Termination and Biasing ON** With Termination and Biasing OFF With Termination and Biasing ON** 1 OFF ON OFF ON 2 OFF ON OFF ON 3 OFF ON OFF ON 4 OFF ON OFF OFF 5 OFF OFF ON ON 6 OFF OFF ON ON 7 ON ON OFF OFF 8 OFF OFF ON ON **Only for reader installed at the ends in the RS485 network PAT 1111 Installation Manual Page 5 of 6
Photographs of the Reader Front view Rear view Access Granted/Denied Indication LED Contactless LED 10 pin terminal block for Wiegand/Magstripe 8 pin terminal block for RS485 Contactless field RS485 DIP switch Testing • Connect the reader to the host through Wiegand/Magstripe/RS485 interface. • Switch on the power to the reader and check if the contactless LED glows. This signifies that the reader is ready. • Wave the test contactless card in front of the reader. Check for the contact less LED to blink steadily. This activity of the reader signifies that the reader is reading the data from the card and passing it to the host. • For a successful read, the access control LED bar should glow in GREEN and a short beep must be heard from the reader. End of the document PAT 1111 Installation Manual Page 6 of 6

Navigation menu