Identiv PAT11211000 Physical Access Terminal User Manual PAT111 Installation Manual

Download:
Mirror Download [FCC.gov]
Document ID	595801
Application ID	i7O5KA4opD4yv83TEGJwrg==
Document Description	Users Manual 1111
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.68kB (96008 bits)
Date Submitted	2005-10-26 00:00:00
Date Available	2005-10-26 00:00:00
Creation Date	2005-10-12 17:43:21
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2005-10-12 17:43:35
Document Title	Microsoft Word - PAT111 Installation Manual
Document Creator	Acrobat PDFMaker 7.0 for Word
Document Author:	Baranidharan.K.M

PAT 1111
Installation Manual
Rev 1.0
31 Aug 2005
st
PAT 1111 Installation Manual
Page 1 of 6
Package Details
•
•
•
•
PAT 1111
Mounting plate and screws
Test card (contactless)
Installation manual
Recommendations
•
•
•
Cable, 10 conductor (Wiegand/Magstripe), 22GA Shielded, Upto 150 mtrs, Line Resistance 2.5 ohms
Cable, 8 conductor (RS485), 22AWG twisted pair, Upto 4000 feet
Regulated DC power supply unit
Specifications
Host Interface
SAM
Contactless
Human Interface
Application
Dimensions
Power
Approvals
PAT 1111 Installation Manual
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wiegand/Magstripe (CLK/Data)
RS485 (2 or 4 wires)
3 relay inputs to set reader state
ISO 7816 1-3
T=0, T=1 protocol support (5V card)
Communication speed up to 344,086 bps
ISO 14443 Type A and B (13.56 MHz)
Supports ISO 14443 part 1 to 4
Operating distance: 1 inch
Communication speed: 106 Kbps
Internal 3DES for card authentication (DESFire)
1 LED beam (green and red) for access information
(granted and denied)
1 LED for contactless card access
Buzzer for user acoustic feedback
Full SDK (software development kit) available
Field Secure firmware upgrade
LWH 148 84 46 mm
10V to 16V DC – 200mA
FCC, UL 294, CE
Page 2 of 6
Installation Instructions
•
•
Fix the mounting plate in an appropriate position on the wall, where the cable can be easily
connected to the back of the reader.
Place the reader on the mounting plate and fix it by using mounting screw.
This is shown in the picture below.
Connector
Male - female
Cable
Unit
Screw
Mounting
plate
PAT 1111 Installation Manual
Page 3 of 6
Mounting plate details
Fig 1.1 Mounting plate (Horizontal view)
Fig 1.2 Mounting plate (Normal view)
PAT 1111 Installation Manual
Fig 1.3 Mounting plate (Vertical view)
Page 4 of 6
Connector details
Connector details for Wiegand/Magstripe – 10pin Terminal Block
Pin Number
10
Signal Name
Relay IN1
Relay IN2
Relay IN3
Relay GND
Wiegand Data0 / Mag Data
Wiegand Data1 / Mag CLK
Wiegand LED IN
Wiegand Buzzer IN
Wiegand GND
Wiegand +12V
Connector details for RS485 – 8pin Terminal Block
Pin Number
Signal Name
(Full Duplex Operation )
Signal Name
(Half Duplex Operation)
RX_A
RX_B
TX_A
TX_B
RS485 GND
SHIELD
Power +12V
Power GND
RX/TX_A
RX/TX_B
No connection
No connection
RS485 GND
SHIELD
Power +12V
Power GND
A – Non-inverted RS485 differential signal; B – Inverted RS485 differential signal
Configuration details for RS485 DIP switch - 8 position, Termination & Biasing Selection Switch.
Switch
Position
Full Duplex RS485
With Termination
and Biasing OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
With Termination
and Biasing ON**
ON
ON
ON
ON
OFF
OFF
ON
OFF
Half Duplex RS485
With Termination
and Biasing OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
With Termination and
Biasing ON**
ON
ON
ON
OFF
ON
ON
OFF
ON
**Only for reader installed at the ends in the RS485 network
PAT 1111 Installation Manual
Page 5 of 6
Photographs of the Reader
Front view
Rear view
Access Granted/Denied
Indication LED
Contactless LED
10 pin terminal block for
Wiegand/Magstripe
8 pin terminal block for
RS485
Contactless field
RS485 DIP switch
Testing
•
•
•
•
Connect the reader to the host through Wiegand/Magstripe/RS485 interface.
Switch on the power to the reader and check if the contactless LED glows. This signifies that the
reader is ready.
Wave the test contactless card in front of the reader. Check for the contact less LED to blink steadily.
This activity of the reader signifies that the reader is reading the data from the card and passing it to
the host.
For a successful read, the access control LED bar should glow in GREEN and a short beep must be
heard from the reader.
End of the document
PAT 1111 Installation Manual
Page 6 of 6

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Company                         : SCM
Source Modified                 : D:20051005045300
Create Date                     : 2005:10:12 17:43:21-07:00
Creator Tool                    : Acrobat PDFMaker 7.0 for Word
Modify Date                     : 2005:10:12 17:43:35-07:00
Metadata Date                   : 2005:10:12 17:43:35-07:00
Document ID                     : uuid:79abfaae-b119-4f43-95fd-e14457f73751
Instance ID                     : uuid:f247fba7-d709-4c81-a1fd-3cc799c756fc
Version ID                      : 90
Format                          : application/pdf
Title                           : Microsoft Word - PAT111 Installation Manual
Creator                         : Baranidharan.K.M
Subject                         : 
Headline                        : 
Page Count                      : 6
Page Layout                     : OneColumn
Author                          : Baranidharan.K.M

EXIF Metadata provided by EXIF.tools