Identiv PAT11211000 Physical Access Terminal User Manual PAT1121 Installation Manual

Download:
Mirror Download [FCC.gov]
Document ID	595802
Application ID	i7O5KA4opD4yv83TEGJwrg==
Document Description	Users Manual 1121
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.01kB (100064 bits)
Date Submitted	2005-10-26 00:00:00
Date Available	2005-10-26 00:00:00
Creation Date	2005-10-12 17:43:55
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2005-10-12 17:44:10
Document Title	Microsoft Word - PAT1121 Installation Manual
Document Creator	Acrobat PDFMaker 7.0 for Word
Document Author:	Baranidharan.K.M

PAT 1121
Installation Manual
Rev1.0
31st Aug 2005
PAT 1121 Installation Manual
Page 1 of 6
Package Details
•
•
•
•
PAT 1121
Mounting plate and screws
Test card (contactless)
Installation manual
Recommendations
•
•
•
Cable, 10 conductor (Wiegand/Magstripe), 22GA Shielded, Upto 150 mtrs, Line Resistance 2.5 ohms
Cable, 8 conductor (RS485), 22AWG twisted pair, Upto 4000 feet
Regulated DC power supply unit
Specifications:
Host Interface
SAM
Contactless
Keypad
Human Interface
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Application
Dimensions
Power
Approvals
PAT 1121 Installation Manual
•
•
•
•
•
•
Wiegand/Magstripe (CLK/Data)
RS485 (2 or 4 wires)
3 relay inputs to set reader state
ISO 7816 1-3
T=0, T=1 protocol support (5V card)
Communication speed up to 344,086 bps
ISO 14443 Type A and B (13.56 MHz)
Supports ISO 14443 part 1 to 4
Operating distance: 1 inch
Communication speed: 106 Kbps
Internal 3DES for card authentication (DESFire)
Standard telephone layout (0-9, Clear and Enter)
Robust hard cap, silicon keypad
1 LED beam (green and red) for access information
(granted and denied)
1 LED per media type (contactless and keypad) to
indicate the type of requested operation
Buzzer for user acoustic feedback
Full SDK (software development kit) available
Field Secure firmware upgrade
LWH 148x84x46 mm
10V to 16V DC- 200mA
FCC, UL294, CE
Page 2 of 6
Installation Instructions:
•
•
Fix the mounting plate in an appropriate position on the wall, where the cable can be easily
connected to the back of the reader.
Place the reader on the mounting plate and fix it by using mounting screw.
This is shown in the picture below.
Connector
Male - female
Cable
Unit
Screw
Mounting
plate
PAT 1121 Installation Manual
Page 3 of 6
Mounting plate details
Fig 1.1 Mounting plate (Horizontal view)
Fig 1.2 Mounting plate (Normal view)
PAT 1121 Installation Manual
Fig 1.3 Mounting plate (Vertical view)
Page 4 of 6
Connector details
Connector details for Wiegand/Magstripe – 10pin Terminal Block
Pin Number
10
Signal Name
Relay IN1
Relay IN2
Relay IN3
Relay GND
Wiegand Data0 / Mag Data
Wiegand Data1 / Mag CLK
Wiegand LED IN
Wiegand Buzzer IN
Wiegand GND
Wiegand +12V
Connector details for RS485 – 8pin Terminal Block
Pin Number
Signal Name
(Full Duplex Operation )
Signal Name
(Half Duplex Operation)
RX_A
RX_B
TX_A
TX_B
RS485 GND
SHIELD
Power +12V
Power GND
RX/TX_A
RX/TX_B
No connection
No connection
RS485 GND
SHIELD
Power +12V
Power GND
A – Non-inverted RS485 differential signal; B – Inverted RS485 differential signal
Configuration details for RS485 DIP switch - 8 position, Termination & Biasing Selection Switch.
Switch
Position
Full Duplex RS485
With Termination
and Biasing OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
With Termination
and Biasing ON**
ON
ON
ON
ON
OFF
OFF
ON
OFF
Half Duplex RS485
With Termination
and Biasing OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
With Termination and
Biasing ON**
ON
ON
ON
OFF
ON
ON
OFF
ON
**Only for reader installed at the ends in the RS485 network
PAT 1121 Installation Manual
Page 5 of 6
Photographs of the Reader
Front view
Rear view
Access Granted/Denied
Indication LED
Contactless LED
Pin pad LED
10 pin terminal block for
Wiegand/Magstripe
8 pin terminal block for
RS485
Pin pad
RS485 DIP switch
Testing:
•
•
•
•
•
•
•
Connect the reader to the host through Wiegand/Magstripe/RS485 interface
Switch on the power to the reader and check if the keypad LED glows. This signifies that the reader is
waiting for the PIN
Enter the PIN
Check if the contactless LED glows. This activity of the reader signifies that the PIN has been
successfully accepted and the reader is waiting for the contactless card.
Wave the Contactless Test card in front of the reader.
Check for the contact less LED to blink steadily .This activity of the reader signifies that the reader is
reading the data from the card and passing it to the host.
For a successful read, the access control LED bar should glow in GREEN and a short beep sound
must be heard from the reader.
End of the document
PAT 1121 Installation Manual
Page 6 of 6

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Company                         : SCM
Source Modified                 : D:20051005045300
Create Date                     : 2005:10:12 17:43:55-07:00
Creator Tool                    : Acrobat PDFMaker 7.0 for Word
Modify Date                     : 2005:10:12 17:44:10-07:00
Metadata Date                   : 2005:10:12 17:44:10-07:00
Document ID                     : uuid:84118ad4-0a57-465a-a5b1-c56a6966698d
Instance ID                     : uuid:9812d187-ea08-49c9-9fa6-32cd4caded4b
Version ID                      : 86
Format                          : application/pdf
Title                           : Microsoft Word - PAT1121 Installation Manual
Creator                         : Baranidharan.K.M
Subject                         : 
Headline                        : 
Page Count                      : 6
Page Layout                     : OneColumn
Author                          : Baranidharan.K.M

EXIF Metadata provided by EXIF.tools