Identiv SDI011-1000 Smart Card Reader User Manual Reference manual

Identiv, Inc Smart Card Reader Reference manual

User Manual

SCM Microsystems Reference Manual – version 1.01 SDI011 Dual interface (contactless and contact) stationary reader
Reference manual SDI011 Dual Interface (Contactless and Contact) Stationary Reader © SCM Microsystems Oskar-Messter-Strasse, 13 85737 Ismaning Germany Phone +49 89 9595 5000 • Fax +49 89 9595 5555
Document history Date Version Description of change 08/09/2010 1.0 Initial Version 11/10/2010 1.01 Add FCC warning Typo corrections Contact information http://www.scmmicro.com/products-services/smart-card-readers-terminals/contactless-dual-interface-readers.html For sales information, please email sales@scmmicro.com
Table of Contents 1. Legal information ................................................................................................................... 9 1.1. Disclaimers ..................................................................................................................... 9 1.2. FCC ................................................................................................................................ 9 1.2.1. Section 15.21 Information to user ........................................................................... 9 1.2.2. Section 15.105 (b) ................................................................................................... 9 1.3. Licenses ......................................................................................................................... 9 1.4. Trademarks .................................................................................................................. 10 2. Introduction to the manual ................................................................................................... 11 2.1. Objective of the manual ............................................................................................... 11 2.2. Target audience ........................................................................................................... 11 2.3. Product version corresponding to the manual ............................................................. 11 2.4. Definition of various terms and acronyms .................................................................... 12 2.5. References ................................................................................................................... 13 2.6. Conventions ................................................................................................................. 14 3. General information about SDI011 ...................................................................................... 15 3.1. SDI011 key benefits ..................................................................................................... 15 3.2. SDI011 key features ..................................................................................................... 15 3.3. SDI011 ordering information ........................................................................................ 16 3.4. SDI011 customization options ...................................................................................... 16 3.5. Contactless communication principles and SDI011 usage recommendations ............ 17 3.5.1. Power supply......................................................................................................... 17 3.5.2. Data exchange ...................................................................................................... 17 3.5.3. Recommendations ................................................................................................ 18 3.6. Applications .................................................................................................................. 19 3.6.1. General ................................................................................................................. 19 3.6.2. Applications provided by SCM Microsystems ....................................................... 19 4. SDI011 characteristics ........................................................................................................ 20 4.1. SDI011 high level architecture ..................................................................................... 20 4.1.1. Block diagram ....................................................................................................... 20 4.1.2. Software architecture ............................................................................................ 21 4.2. Quick reference data .................................................................................................... 22 4.2.1. SDI011 dimensions ............................................................................................... 22 4.2.2. LED behavior ........................................................................................................ 23 4.2.3. Other data ............................................................................................................. 24 5. Software modules ................................................................................................................ 26 5.1. Installation .................................................................................................................... 26 5.2. Utilities .......................................................................................................................... 26 5.3. Driver ............................................................................................................................ 26 5.3.1. SDI011 listing ........................................................................................................ 26 5.3.2. Supported operating systems ............................................................................... 27
5.3.3. PC/SC 2.0 compliant ATR for contactless interface ............................................. 27 5.4. Firmware ...................................................................................................................... 30 5.4.1. CCID transport protocol ........................................................................................ 30 5.4.2. Automatic PPS for the contactless interface ......................................................... 31 6. Commands description ........................................................................................................ 32 6.1. Generic APDU .............................................................................................................. 32 6.1.1. Get UID Command ............................................................................................... 32 6.1.2. Escape command APDU ...................................................................................... 34 6.2. Set of APDU for contactless storage user tokens ........................................................ 35 6.2.1. STORAGE_CARD_CMDS_READ_BINARY ........................................................ 35 6.2.2. STORAGE_CARD_CMDS_WRITE_BINARY ...................................................... 37 6.2.3. STORAGE_CARD_CMDS_LOAD_KEYS ............................................................ 39 6.2.4. STORAGE_CARD_CMDS_AUTHENTICATE ...................................................... 40 6.2.5. STORAGE_CARD_CMDS_VALUE_BLOCK ....................................................... 42 6.3. Set of APDU for ISO/IEC14443-4 user tokens ............................................................ 43 6.3.1. T=CL Command .................................................................................................... 43 6.3.2. T=CL user command ............................................................................................ 44 6.4. Set of APDU defined by SCM Microsystems ............................................................... 45 6.4.1. MIFARE DESFire Commands .............................................................................. 45 6.5. Escape commands for the contactless interface ......................................................... 46 6.5.1. Sending escape commands to SDI011 ................................................................ 46 6.5.2. Escape command codes ....................................................................................... 46 6.5.3. READER_GETCARDINFO ................................................................................... 47 6.5.4. READER_LED_CONTROL_BY_FW .................................................................... 48 6.5.5. READER_LEDCONTROL .................................................................................... 48 6.5.6. READER_CNTLESS_GET_MFRC_REV ............................................................. 48 6.5.7. READER_CNTLESS_GET_ATS_ATQB .............................................................. 49 6.5.8. READER_CNTLESS_GET_TYPE ....................................................................... 49 6.5.9. READER_CNTLESS_SET_TYPE ........................................................................ 49 6.5.10. READER_CNTLESS_RF_SWITCH ..................................................................... 50 6.5.11. READER_CNTLESS_RAW_CFG ........................................................................ 50 6.5.12. READER_CNTLESS_RAW_XMIT_EX ................................................................ 51 6.5.13. READER_ CNTLESS_DISABLE_PPS ................................................................. 52 6.5.14. READER_SWITCH_RF_ON_OFF ....................................................................... 52 6.5.15. READER_CNTLESS_848KBPS ........................................................................... 53 6.5.16. READER_CNTLESS_BAUDRATE ....................................................................... 54 6.5.17. READER_CNTLESS_FORCE_BAUDRATE_PCSC_REV2 ................................ 55 6.6. Escape commands for the contact interface ................................................................ 56 6.6.1. Sending escape commands to SDI011 ................................................................ 56 6.6.2. Escape command codes ....................................................................................... 56 6.6.3. READER_SETMODE ........................................................................................... 56 6.6.4. READER_GETMODE ........................................................................................... 57 6.6.5. READER_APDU_TRANSFER.............................................................................. 57 6.6.6. READER_SWITCH_SPEED ................................................................................. 58 6.6.7. READER_SWITCH_PROTOCOL......................................................................... 58 6.6.8. READER_DISABLE_PPS ..................................................................................... 59 6.6.9. READER_GETIFDTYPE ...................................................................................... 59 6.6.10. READER_GETINFO_EXTENDED ....................................................................... 60 7. Annexes ............................................................................................................................... 61 7.1. Annex A – Status words table ...................................................................................... 61 7.2. Annex B – Sample code using escape commands through Escape IOCTL ............... 62 7.3. Annex C - SCM Proprietary CLA bytes ........................................................................ 67
7.4. Annex D – Mechanical drawings .................................................................................. 68 7.4.1. Top Casing ............................................................................................................ 68 7.4.2. Bottom Casing ...................................................................................................... 69 7.4.3. Stand ..................................................................................................................... 70
SDI011 REFERENCE MANUAL 9 1. Legal information 1.1. Disclaimers The content published in this document is believed to be accurate. SCM Microsystems does not, however, provide any representation or warranty regarding the accuracy or completeness of its content and regarding the consequences of the use of information contained herein. If this document has the status ―Draft‖, its content is still under internal review and yet to be formally validated. SCM Microsystems reserves the right to change the content of this document without prior notice. The content of this document supersedes the content of previous versions of the same document. The document may contain application descriptions and/or source code examples, which are for illustrative purposes only. SCM Microsystems gives no representation or warranty that such descriptions or examples are suitable for the application that the reader may want to use them for. Should you notice problems with the provided documentation, please provide your feedback to support@scmmicro.com. 1.2. FCC 1.2.1. Section 15.21 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment 1.2.2. Section 15.105 (b) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. 1.3. Licenses If the document contains source code examples, they are provided for illustrative purposes only and subject to the following restrictions:  You MAY at your own risk use or modify the source code provided in the document in applications you may develop. You MAY distribute those applications ONLY in form of compiled applications.
SDI011 REFERENCE MANUAL 10  You MAY NOT copy or distribute parts of or the entire source code without prior written consent from SCM Microsystems.  You MAY NOT combine or distribute the source code provided with Open Source Software or with software developed using Open Source Software in a manner that subjects the source code or any portion thereof to any license obligations of such Open Source Software. If the document contains technical drawings related to SCM Microsystems products, they are provided for documentation purposes only. SCM Microsystems does not grant you any license to its designs. 1.4. Trademarks MIFARE is a registered trademark of NXP Semiconductors BV. Windows is a trademark of Microsoft Corporation.
SDI011 REFERENCE MANUAL 11 2. Introduction to the manual 2.1. Objective of the manual This manual provides an overview of the hardware and software features of the SDI011 dual interface (contactless and contact) reader, hereafter referred to as ―SDI011‖. This manual describes in details interfaces and supported commands available for developers using SDI011 in their applications. 2.2. Target audience This document describes the technical implementation of SDI011. The manual targets software developers. It assumes knowledge about 13.56 MHz contactless technologies like ISO/IEC 14443 and commonly used engineering terms. Should you have questions, you may send them to support@scmmicro.com . 2.3. Product version corresponding to the manual Item Version Hardware 1.0 Firmware 7.36 Windows Contact Driver 5.19 Windows Contactless Driver 5.20 MAC driver 5.0.18 LINUX Driver 5.0.18
SDI011 REFERENCE MANUAL 12 2.4. Definition of various terms and acronyms Term Expansion APDU Application Protocol Data Unit ATR Answer to Reset, defined in ISO7816 ATS Answer to select, defined in ISO/IEC 14443 Byte Group of 8 bits CCID Chip Card Interface Device CID Card Identifier CL Contactless DFU Device Firmware Upgrade DR Divider receive: used to determine the baud rate between the reader to the card DS Divider send: used to determine the baud rate between the card to the reader LED Light emitting diode MIFARE The ISO14443 Type A with extensions for security (NXP) NA Not applicable NAD Node Address Nibble Group of 4 bits. 1 digit of the hexadecimal representation of a byte. Example: 0xA3 is represented in binary as (10100011)b. The least significant nibble is 0x3 or (0011)b and the most significant nibble is 0xA or (1010)b PCD Proximity Coupling Device PC/SC Personal Computer/Smart Card: software interface to communicate between a PC and a smart card PICC Proximity Integrated Chip Card PID Product ID Proximity Distance coverage till ~10 cm. PUPI Pseudo unique PICC identifier RFU Reserved for future use RF Radio Frequency STCII Smart card reader controller ASIC from SCM Microsystems USB Universal Serial Bus VID Vendor ID (xyz)b Binary notation of a number x, y, z 0,1 0xYY The byte value YY is represented in hexadecimal
SDI011 REFERENCE MANUAL 13 2.5. References Doc ref in the manual Description Issuer ISO/IEC 7816-3 Identification cards — Integrated circuit cards — Part 3: Cards with contacts — Electrical interface and transmission protocols ISO / IEC ISO/IEC 7816-4 Identification cards - Integrated circuit(s) cards with contacts Part 4: Interindustry commands for interchange ISO/IEC 7816-4: 1995 (E) ISO / IEC ISO/IEC 14443-3 Identification cards — Contactless integrated circuit(s) cards — Proximity cards — Part 3: Initialization and anti-collision ISO / IEC ISO/IEC 14443-4 Identification cards — Contactless integrated circuit(s) cards — Proximity cards Part 4: Transmission protocol ISO/IEC 14443-4:2001(E) ISO / IEC PC/SC Interoperability Specification for ICCs and Personal Computer Systems v2.01 PC/SC Workgroup CCID Specification for Integrated Circuit(s) Cards Interface Devices 1.1 USB-IF USB Universal Serial Bus Specification 2.0 USB-IF
SDI011 REFERENCE MANUAL 14 2.6. Conventions Bits are represented by lower case ‗b‘ where followed by a numbering digit. Bytes are represented by upper case ‗B‘ where followed by a numbering digit. b7 b6 b5 b4 b3 b2 b1 b0B4 B5 B6 B7 B8 B9 B10 B11B0 B1 B2 B3Least significant nibbleMost significant nibble1 Byte = 8 bits = 2 nibblesBit number 0Bit number 5String of 12 bytesByte number 11Byte number 2 Example: 163 decimal number is represented  in hexadecimal as 0xA3  in binary as (10100011)b The least significant nibble of 0xA3 is  0x3 in hexadecimal  (0011)b in binary The most significant nibble of =xA3 is  0xA in hexadecimal  (1010)b in binary
SDI011 REFERENCE MANUAL 15 3. General information about SDI011 3.1. SDI011 key benefits With its combination of a modern slim design and its state of the art feature set, SDI011 is the perfect desktop reader choice for environments where both contact and contactless smart card support is required. Such environments may be corporate where physical and logical access control is implemented. As for all SCM Microsystems products, SDI011 is designed to offer best in class interoperability with various formats of tokens: cards, dongles, watches or NFC mobile phones. Its infield upgradeable firmware makes SDI011 a secure and future-proof investment providing both flexibility and fast time to market for new applications as well as minimum risk linked to contactless technology standards evolution. 3.2. SDI011 key features  13.56MHz contactless reader: o ISO14443 type A & B, o MIFARE  ISO7816 compliant contact smart card reader  PC/SC v2.0 compliant  In field upgradeable firmware  Unique serial number which enables that SDI011 can be plugged into any USB slot on a PC without having to re-install the driver.
SDI011 REFERENCE MANUAL 16 3.3. SDI011 ordering information Item Part number SDI011 905214 Contactless SDK 905124 Contact SDK 905129 3.4. SDI011 customization options Upon request, SCM can customize:  The color of the casing  The logo  The product label  The USB strings Terms and conditions apply, please contact your local SCM representative or send an email to sales@scmmicro.com.
SDI011 REFERENCE MANUAL 17 3.5. Contactless communication principles and SDI011 usage recommendations SDI011 is a dual interface reader capable of reading both contact smart cards and contactless user tokens. The following paragraph focuses on a few specifics of the contactless communication to outline usage recommendations in order to ensure best user experience. SDI011 is a contactless reader1 designed to communicate with user tokens. User tokens2 are made of a contactless integrated circuit card connected to an antenna User tokens can take several form factors:  Credit card sized smart card  Key fob  NFC mobile phone etc… Communication between SDI011 and user tokens uses magnetic field inductive coupling. The magnetic field generated by SDI011 has a carrier frequency of 13.56MHz. 3.5.1. Power supply When the user token is put in the magnetic field of the reader, its antenna couples with the reader and an induction current appears in the antenna thus providing power to the integrated circuit. The generated current is proportional to the magnetic flux going through the antenna of the user token. 3.5.2. Data exchange The carrier frequency of the magnetic field is used as a fundamental clock signal for the communication between the reader and the card. It is also used as a fundamental clock input for the integrated circuit microprocessor to function. To send data to the user token the reader modulates the amplitude of the field. There are several amplitude modulation and data encoding rules defined in ISO/IEC 14443. The reader should refer to the standard for further details. To answer to the reader, the integrated circuit card of the user token modulates its way of loading (impedance) the field generated by the reader. Here also further details can be found in ISO/IEC 14443. 1 In the ISO/IEC 14443 standard, the reader is called the proximity coupling device (PCD) 2 In the ISO/IEC 14443 standard, the user token is called proximity integrated chip card (PICC)
SDI011 REFERENCE MANUAL 18 3.5.3. Recommendations The communication between the reader and the user token is sensitive to the presence of material or objects interfering with the magnetic field generated by the reader. The presence of conductive materials like metal in the vicinity of the reader and the user token can severely degrade the communication and even make it impossible. The magnetic field of the reader generates Eddy or Foucault‘s currents in the conductive materials; the field is literally absorbed by that kind of material.  It is recommended for proper communication to avoid putting SDI011 in close proximity of conductive materials. The presence of multiple user tokens in the field also interferes with the communication. When several user tokens are in the field of the reader, load of the field increases which implies that less energy is available for each of them and that the system is detuned. For this reason, SCM Microsystems has implemented in its driver only 1 slot by default. This means that in the event several user tokens are in the field of the SDI011, only one will be active. It is possible using INF configuration to enable up to 4 slots – i.e. to activate up to 4 user tokens nevertheless depending on the power consumption of the user tokens communication cannot be guaranteed.  It is recommended to present only one user credential at a time in front of SDI011. Please note that multiple contactless slots feature is supported but is kept disabled by default. The SDI011 driver on configuration allows the presence and use of several PICCs (maximum 4) at the same time. The driver can support multiple logical connections and present each of them as a slot logical device to the Resource Manager and higher components. Also the simultaneous working of multiple Contactless cards is not guaranteed and depends on the antenna size and the power requirements of the card. The communication between the reader and the user token is sensitive to the geometry of the system {reader, user token}. Parameters like the geometry and specially the relative size of the reader and user token antennas directly influence the inductive coupling and therefore the communication. SDI011 was primarily designed and optimized to function with user credentials of various technologies having the size of a credit card.  It may happen that SDI011 is not capable of communicating with extremely large or extremely small antennas.  In order to optimize the coupling between the reader and the user token, it is recommended to put both antennas as parallel as possible  In order to optimize transaction speed between the reader and the card it is recommended to place the user token as close as possible to the reader. This will increase the amount of energy supplied to the user credential which will then be able to use its microprocessor at higher speeds
SDI011 REFERENCE MANUAL 19 3.6. Applications 3.6.1. General SDI011 is a transparent reader designed to interface a personal computer host supporting PC/SC interface with 13.56MHz user tokens like public transport cards, contactless banking cards, electronic identification documents – e.g. e-passports, e-ID cards, driving licenses etc. Those user tokens can have several form factors like credit cards, key fobs, NFC mobile phones or USB dongles like SCT3511 that SCM Microsystems markets. SDI010TokensApplication logic + User personal data for given set of applicationsUSB linkPC/SC interface RF link (13.56MHz)ISO14443 interfaceHostApplication logicSDI010 Interface deviceNetwork` SDI011 itself handles the communication protocol but not the application related to the token. The application-specific logic has to be implemented by software developers on the host. 3.6.2. Applications provided by SCM Microsystems SCM Microsystems does not provide payment or transport applications. SCM Microsystems provides a few applications for development and evaluation purposes that can function with SDI011. There are many tools provided; here are two of them:  The NFC forum tag reader/writer is a standalone application that enables the user to read and write NFC forum compliant records into NFC forum compatible tags. It is an easy to use tool to configure rapidly NFC forum tag demonstrations. Note: SDI011 supports NFC forum tag type 2 and 4, only.  Smart card commander version 1.1 provides NFC forum record parsing functionality of NDEF records in XML format as well as scripting functionality which can be very useful for developers to develop and debug their applications. This tool can be used for both the contact and the contactless interfaces of SDI011.
SDI011 REFERENCE MANUAL 20 4. SDI011 characteristics 4.1. SDI011 high level architecture 4.1.1. Block diagram The link between SDI011 and the host to which it is connected is the USB interface providing both the power and the communication channel. Device controllerSTC2 ASIC (SCM) with embedded flashRF front-endMFRC531 (NXP)EMC filter + Matching circuitry LEDtexttexttextAntennaTo hostISO7816 contact smart card interface SDI011 has a device controller which is SCM‘s STCII ASIC. This ASIC has several interfaces available. In SDI011 implementation 3 peripherals are connected to the device controller:  LED for reader status indication  A contact smart card interface  An RF front-end that handles the RF communication The ASIC embeds flash memory. The flash is programmed during the manufacturing of SDI011 devices. This flash contains the firmware developed by SCM Microsystems to handle all the ISO7816 contact protocol, the RF communication protocols and the PC/SC communication protocol with the host. The flash can be upgraded once the device is deployed in the field, hence enabling firmware upgrades to add and potentially patch features. The RF front-end ensures the coding/decoding/framing modulation/demodulation required for the RF communication. It is controlled by the device controller through registers. The matching circuitry provides the transmission and receiver paths adaptation for the antenna to function properly.
SDI011 REFERENCE MANUAL 21 4.1.2. Software architecture Applications can interface with the driver directly through the PC/SC interface. The SDI011 driver implements PC/SC v2.0 API towards upper layers and uses SCM firmware commands encapsulated in CCID-like protocol for the contactless slot and full CCID for the contact slot. The SDI011 contactless driver handles all the contactless-related intelligence – i.e. ISO/IEC 14443 and the SDI011 firmware handles the raw transport of data to and from the contactless cards.
SDI011 REFERENCE MANUAL 22 4.2. Quick reference data 4.2.1. SDI011 dimensions Item Characteristic Value SDI011 Weight 128 Grams External dimensions L 118 mm  W 78mm  H 22mm Cable length 1.5 meter long with USB type A connector Default color Black with metallic silver Default label Drawing with dimensions of the SDI011 and accessories can be found in annex.
SDI011 REFERENCE MANUAL 23 4.2.2. LED behavior SDI011 is equipped with a bicolor LED. Its behavior is described in the table below. SDI011 states LED1 Indication (GREEN) LED2 Indication (RED) Just after plug-in (with drivers already installed) ON OFF Just after DFU operation ON OFF Suspend / standby OFF OFF Reader powered, Contact card IN, but not powered (98/ME – issue power down using the Testresman utility) 500ms ON 500ms OFF OFF Reader powered, Contact card IN, but not powered (2K/XP – power down takes place ) ON OFF Reader powered, Contactless card IN, but not powered (98/ME - issue power down using the Testresman utility) 500ms ON 500ms OFF 500ms ON 500ms OFF Reader powered, Contactless card IN, but not powered (2K/XP - power down takes place ) ON ON Contact card powered / communication 500ms ON 500ms OFF OFF Contactless card powered / communication 500ms ON 500ms OFF 500ms ON 500ms OFF Reader / card errors OFF 100ms ON 100ms OFF Firmware upgrade running OFF ON Combi3 card powered in contact Slot 500ms ON 500ms OFF OFF Combi card powered using RF field 500ms ON 500ms OFF 500ms ON 500ms OFF 3 A combi card is a smart card which has both a contact and a contactless interface. Some of those cards have one controller with two interfaces. Data can be accessed through the contact or the contactless interface. For those when the contact interface is powered up the contactless interface is disabled. There are nevertheless in the market combi cards with 1 contact chip and 1 contactless chip. Those cards can be seen at the same time as a contact and a contactless card when inserted in the contact interface of SDI011.
SDI011 REFERENCE MANUAL 24 4.2.3. Other data 4.2.3.1. General Parameter Value/Description Clock of the device controller 24 MHz API PC/SC 2.0 Operating temperature range 0º to 50ºC Operating humidity range Up to 95%RH non condensing Certifications USB CE FCC VCCI WEEE RoHS WHQL 4.2.3.2. USB Parameter Value/Description DC characteristics High bus powered (SDI011 draws power from USB bus) Voltage: 5V Max. Current : 200mA Suspend current : 380uA USB specification USB 2.0 FS Device USB Speed Full Speed Device (12Mbit/s) Device Class Vendor PID 0x5121 VID 0x04E6
SDI011 REFERENCE MANUAL 25 4.2.3.3. Contactless interface Parameter Value/Description RF carrier frequency 13.56 MHz +/- 50ppm Modulation 12 to 14 % ID1 format tokens supported ISO/IEC 14443-4 PICC type A and type B MIFARE Type B memory card PICC through SCM-proprietary APDU Maximum baud rate 424Kbps (848 Kbps is available as configurable option) Multiple PICC in field Supported and is kept disabled by default. Allows the presence and use of several PICC‘s (Maximum 4) at the same time. The driver can support multiple logical connections and present each of them as a slot logical device to the Resource Manager and higher components. Also the simultaneous working of multiple Contactless cards is not guaranteed and depends on the antenna size and the power requirements of the card. 4.2.3.4. Contact interface Parameter Value/Description Smart card operating frequency 4MHz Maximum supported card baud-rate 500Kbps Cards supported Class A and Class AB smart cards (Class B only cards not supported) Synchronous smart cards ISO-7816 compliant Yes EMV‘2000 compliant Not validated CT-API compliant Yes Number of slots Single smart card slot Ejection mechanism Manual
SDI011 REFERENCE MANUAL 26 5. Software modules 5.1. Installation SCM provides an installer for Windows and for Mac The installers can be used to install the driver as well as some utilities. 5.2. Utilities The following utilities are available:  A tool for device firmware upgrade (DFU)  A tool for testing the installation of the PC/SC driver  A tool for testing the resource manager  A tool called PC/SC Diag capable of providing basic information about the reader and a card through PC/SC stack The DFU utility comes with a specific driver for dynamic Device Firmware Upgrade (DFU) through the USB interface.  Operating systems supported by DFU tool:  Windows 98  Windows ME  Windows 2000  Windows 2003 Server (32 & 64 bit)  Windows XP (32 & 64 bit)  Windows Vista (32 & 64 bit)  Windows Server 2008 (32 & 64 bit) 5.3. Driver 5.3.1. SDI011 listing SDI011 is listed by PC/SC applications as  SCM Microsystems Inc. SDI011 Smart Card Reader for the contact reader  SCM Microsystems Inc. SDI011 Contactless Reader for the contactless reader
SDI011 REFERENCE MANUAL 27 5.3.2. Supported operating systems  Operating systems supported by the driver:  Windows 98  Windows ME  Windows 2000  Windows 2003 Server (32 & 64 bit)  Windows XP (32 & 64 bit)  Windows Vista (32 & 64 bit)  Windows Server 2008 (32 & 64 bit) 5.3.3. PC/SC 2.0 compliant ATR for contactless interface When a user token is placed on the reader, initialization, anti-collision is done. The user token is automatically activated and an ATR is built as defined in the PC/SC specification.
SDI011 REFERENCE MANUAL 28 5.3.3.1. ATR for contactless storage user tokens The ATR of the user token is composed as described in the table below. In order to allow the application to identify the storage card properly, it‘s Standard and Card name describing bytes must be interpreted according to the Part 3 Supplemental Document, maintained by PC/SC. Tokens using technology like MIFARE are examples of such user tokens. Byte# Value Designation Description 0 0x3B Initial header 1 0x8n T0 n indicates the number of historical bytes in following ATR 2 0x80 TD1 Nibble8 indicates no TA2, TB2, TC2 Nibble 0 means T=0 3 0x01 TD2 Nibble8 indicates no TA3, TB3, TC3 Nibble 1 means T=1 4...3+n 0x80 A status indicator may be present in an optional TLV data object 0x4F Optional TLV data object Tag: Application identifier Length 1 byte RID Registered identifier on 5 bytes PIX Proprietary identifier extension on 3 bytes 0x00 0x00 0x00 0x00 4 RFU bytes 4+n TCK XOR of all previous bytes Example of the ATR built for contactless storage tokens: MIFARE Classic 4K MIFARE Ultralight
SDI011 REFERENCE MANUAL 29 5.3.3.2. ATR for ISO/IEC 14443-4 user tokens The user token exposes its ATS or application information which is mapped to an ATR. The table describes how this mapping is done. Byte# Value Designation Description 0 0x3B Initial header 1 0x8n T0 n indicates the number of historical bytes in following ATR 2 0x80 TD1 Nibble8 indicates no TA2, TB2, TC2 Nibble 0 means T=0 3 0x01 TD2 Nibble8 indicates no TA3, TB3, TC3 Nibble 1 means T=1 4...3+n Historical bytes or application information Type A: the historical bytes from the ATS (up to 15 bytes) Type B (8 bytes):  Byte 0 through 3: application data from ATQB,  Byte 4 through 6: protocol info byte from ATQB,  Byte 7: highest nibble is the MBLI (maximum buffer length index) from ATTRIB, lowest nibble is 0x0 4+n TCK XOR of all previous bytes Example of the ATR built for an ISO14443-4 user tokens: Type A Type B
SDI011 REFERENCE MANUAL 30 5.4. Firmware 5.4.1. CCID transport protocol SDI011 implements a transport protocol that is compliant with USB Device Class: Smart Card CCID Specification for Integrated Circuit(s) Cards Interface Devices Revision 1.10 for the contact smart card interface and CCID-like transport protocol for the contactless interface. This paragraph describes the CCID specification features that are implemented and those that are not implemented. 5.4.1.1. CCID class requests supported  Abort 5.4.1.2. CCID messages supported The following CCID messages are supported both for the contact and the contactless interfaces when received through bulk-out endpoint.  PC_to_RDR_IccPowerOn  PC_to_RDR_IccPowerOff  PC_to_RDR_GetSlotStatus  PC_to_RDR_XfrBlock  PC_to_RDR_GetParameters  PC_to_RDR_SetParameters  PC_to_RDR_Escape  PC_to_RDR_Abort  PC_to_RDR_NotifySlotChange The following CCID messages are NOT implemented and hence fail with command not supported error:  PC_to_RDR_ResetParameters  PC_to_RDR_IccClock  PC_to_RDR_T0APDU  PC_to_RDR_Secure  PC_to_RDR_Mechanical  PC_to_RDR_SetDataRateAndClockFrequency 5.4.1.3. CCID Error Codes Extensive error codes are reported on many conditions during all CCID responses. Most of the error messages are reported by the CCID appropriately. Some of the main error codes for the contact interface are:  HW_ERROR  XFR_PARITY_ERROR
SDI011 REFERENCE MANUAL 31  BAD_ATR_TS  BAD_ATR_TCK  ICC_MUTE The following sub-sections discuss when and why these error codes are returned: 5.4.1.3.1. HW_ERROR This error code is returned when a hardware short circuit condition is detected, during application of power to the card or if any other internal hardware error is detected. This error code has been defined in the error code table 6.2-2 of the CCID specification. 5.4.1.3.2. XFR_PARITY_ERROR This error code is returned when a parity error condition is detected. This error will be reported in the response to a PC_to_RDR_XfrBlock message. This error code has been defined in the error code table 6.2-2 of the CCID specification. 5.4.1.3.3. ICC_MUTE This error code is returned when the card does not respond until the reader time out occurs. This error will be reported in the response to PC_to_RDR_XfrBlock message and PC_to_RDR_IccPowerOn messages. This error code has been defined in the error code table 6.2-2 of the CCID specification. 5.4.2. Automatic PPS for the contactless interface Automatic PPS is implemented in SDI011‘s driver. This means that by default SDI011 switches to the maximum communication speed indicated by the card during its selection. Automatic PPS can be disabled using escape messages as explained later in this manual. When Auto PPS is disabled (discussed in escape messages section) the reader works at the default baud rate of 106kbps. An escape command has been introduced in the driver to force the required baud rate. The maximum speed supported by SDI011 is 424Kbps by default. Using escape messages as explained later in this manual it is possible to change this.
SDI011 REFERENCE MANUAL 32 6. Commands description 6.1. Generic APDU 6.1.1. Get UID Command 6.1.1.1. Description GET UID will retrieve the UID or SNR or PUPI of the user token. This command can be used for all supported technologies. 6.1.1.2. Format CLA INS P1 P2 Lc Data in Le 0xFF 0xCA 0x00 0x00 - - XX Setting Le = 0x00 can be used to request the full UID or PUPI is sent back.(e.g. for ISO14443A single 4 bytes, double 7 bytes, triple 10 bytes, for ISO14443B 4 bytes PUPI). 6.1.1.3. Response Data Out UID + SW1 + SW2 6.1.1.4. Status Words SW1 SW2 Description 0x90 0x00 NO ERROR 0x62 0x82 End of UID reached before Le bytes (Le is greater than UID length) 0x6C 0xXX Wrong Length. 0xXX is the exact value for Le Further error codes can be found in annex
SDI011 REFERENCE MANUAL 33 6.1.1.5. Examples ISO14443-4A ISO14443-4B MIFARE 4K MIFARE Ultralight
SDI011 REFERENCE MANUAL 34 6.1.2. Escape command APDU 6.1.2.1. Description This command can be used to send escape commands to SDI011. For description of escape commands please refer to the dedicated chapter in this manual. 6.1.2.2. Format CLA INS P1 P2 P3 Data in 0xFF 0xCC 0x00 0x00 Lc Input buffer of escape command Lc is the length of the escape command‘s input buffer. See escape commands description later in this manual 6.1.2.3. Response Output buffer of the escape command 6.1.2.4. Example To get the ATS or ATQB of the ISO14443-4 based user token, you can use this APDU to send the READER_CNTLESS_GET_ATS_ATQB (0x93) escape command Type A passport Type B passport To get the reader status about support of 848Kbps, you can use this APDU to send the READER_CNTLESS_848KBPS (0x9D) escape command. By default the SDI011 doesn‘t have 848Kbps enabled on its contactless interface, the following sequence  Checks the status (0x00 as response, means 848Kbps is disabled)  Enables 848Kbps  Checks the status again and the answer 0x01 indicates 848Kbps is enabled
SDI011 REFERENCE MANUAL 35 6.2. Set of APDU for contactless storage user tokens 6.2.1. STORAGE_CARD_CMDS_READ_BINARY 6.2.1.1. Description Using this APDU, application can read a memory block on user tokens based on technologies like MIFARE Classic 1K or 4K (block size 0x10 bytes) or MIFARE Ultra light (block size 0x04 bytes). 6.2.1.2. Format CLA INS P1 P2 Le 0xFF 0xB0 Address MSB Address LSB 0xXX Where:  P2 indicates the block number from where to read  Le can be a short (maximum value 255) or extended (maximum value 65535). If Le=0x00, then all the bytes until the end of the block are read (0x10 bytes for MIFARE Classic 1K or 4K cards and 0x04 bytes for MIFARE Ultra Light cards). 6.2.1.3. Response Data Out Data + SW1 + SW2 6.2.1.4. Status words SW1 SW2 Description 0x90 0x00 NO ERROR 0x62 0x81 WARNING: part of the returned data may be corrupted 0x82 WARNING: end of file reached before Le bytes where read 0x67 0x00 Length incorrect 0x68 0x00 CLA byte incorrect 0x69 0x81 Command not supported 0x82 Security status not satisfied 0x86 Command not allowed 0x6A 0x81 Function not supported 0x82 File not found, addressed blocks or bytes do not exist 0x6B 0x00 Wrong P1, P2 parameters 0x6C 0xXX Wrong Le, 0xXX is the correct value
SDI011 REFERENCE MANUAL 36 6.2.1.5. Example For a MIFARE Classic 1K card which has the following memory content: To read the seventh block, you have to issue the following command and get the following response:
SDI011 REFERENCE MANUAL 37 6.2.2. STORAGE_CARD_CMDS_WRITE_BINARY 6.2.2.1. Description This APDU writes data to a memory address 6.2.2.2. Format CLA INS P1 P2 Lc Data in 0xFF 0xD6 Address MSB Address LSB 0xXX Data Where:  P2 indicate the memory block number where data should be written  Lc=0x10 for MIFARE Classic 1K/4K. Lc=0x04 for MIFARE Ultralight 6.2.2.3. Response Data Out SW1 + SW2 6.2.2.4. Status Words SW1 SW2 Description 0x90 0x00 NO ERROR 0x69 0x81 Command not supported 0x64 0x00 State of the non-volatile memory unchanged 6.2.2.5. Example For a MIFARE Classic Ultralight card which has the following memory content: Issuing the command
SDI011 REFERENCE MANUAL 38 Results into the following memory mapping
SDI011 REFERENCE MANUAL 39 6.2.3. STORAGE_CARD_CMDS_LOAD_KEYS 6.2.3.1. Description Some type of user tokens like MIFARE Classic may require that an authentication happens before any data can be read or written. To perform this authentication, keys need to be loaded in the reader‘s memory using this command. 6.2.3.2. Format CLA INS P1 P2 Lc Data in 0xFF 0x82 0x00 Key Type Key Length Key value Where P2 can have the following values (please refer to MIFARE documentation from NXP for further details on what is key A and Key B):  0x60 to use the Key A  0x61 to use the Key B 6.2.3.3. Response Data Out SW1 + SW2 6.2.3.4. Status Words SW1 SW2 Description 0x90 0x00 NO ERROR 0x69 0x83 Reader key not supported 0x85 Secured transmission not supported 0x87 Non volatile memory not available 0x88 Key number not valid 0x89 Key length not correct
SDI011 REFERENCE MANUAL 40 6.2.4. STORAGE_CARD_CMDS_AUTHENTICATE 6.2.4.1. Description This command enables to perform authentication for user tokens based on MIFARE Classic 1K or 4K. Before this command can be successfully executed, the STORAGE_CARD_CMDS_LOAD_KEY command must have been executed. 6.2.4.2. Format CLA INS P1 P2 Lc Data in 0xFF 0x86 0x00 0x00 0x05 Data Where the data field is structured as follow Byte # Value Description B0 0x01 Version B1 Address MSB B2 Address LSB B3 0x60 Key A 0x61 Key B B4 Number of the key to be used for authentication Information about memory structure of MIFARE Classic must be requested from NXP Semiconductors. 6.2.4.3. Response Data Out SW1 + SW2 6.2.4.4. Status Words SW1 SW2 Description 0x90 0x00 NO ERROR 0x63 0x00 WARNING no further info 0x69 0x82 Security status not satisfied 0x84 Referenced key not usable 0x86 Key type not known
SDI011 REFERENCE MANUAL 41 6.2.4.5. Example For a MIFARE Classic 1K card which has the following memory mapping: Reading sector 0 or sector 1 of this card requires authentication with key A or key B. The following example:  authenticates with key A of sector 1  reads block #6  authenticates against sector 3  reads block #E
SDI011 REFERENCE MANUAL 42 6.2.5. STORAGE_CARD_CMDS_VALUE_BLOCK 6.2.5.1. Description This APDU is used to interact with MIFARE Classic e-purse applications. Please refer to MIFARE Classic documentation available from NXP Semiconductors for further details on MIFARE classic memory mapping and commands. 6.2.5.2. Format CLA INS P1 P2 Lc Data in 0xFF 0xF0 0x00 Block# Lc Data Where P2 code the address of the block number addressed Where the data field is structured as follow Byte # Value Description B0 0xC0 Increment 0xC1 Decrement B1 Block number B2-B5 Value (LSB first) 6.2.5.3. Response Data Out SW1 + SW2 6.2.5.4. Status Words SW1 SW2 Description 0x90 0x00 NO ERROR 0x67 0x00 Length incorrect 0x68 0x00 CLA byte incorrect 0x6A 0x81 Function not supported 0x6B 0x00 Wrong P1, P2 parameters 6.2.5.5. Example CLA INS P1 P2 Lc Data in 0xFF 0xF0 0x00 0x1E 0x06 0xC0 0x1E 0x01 0x00 0x00 0x00 The above APDU will increment the value in block number 0x1E of a MIFARE Classic-based user token by a value of 0x01.
SDI011 REFERENCE MANUAL 43 6.3. Set of APDU for ISO/IEC14443-4 user tokens 6.3.1. T=CL Command Description SDI011 can transfer directly ISO/IEC7816-4 APDU to the PICC. SDI011 supports user tokens that have both the MIFARE and T=CL partitions. Depending on the APDU sent by the host, the reader switches to the corresponding mode (MIFARE or T=CL) automatically and the command is processed accordingly. 6.3.1.1. Format CLA INS P1 P2 P3 Data Description of the APDU commands can be found in ISO/IEC 7816-4 specification. 6.3.1.2. Response Data Out PICC answer as defined in ISO/IEC 7816-4+ SW1 + SW2 As defined in ISO/IEC 7816-4. 6.3.1.3. Status Words SW1 SW2 Description See ISO/IEC 7816-4 As defined in ISO/IEC 7816-4. 6.3.1.4. Example The following APDU sequence reads the first 256 bytes of the data group 1 as specified in ICAO LDS (logical data structure) for machine readable travel documents with open access. It first selects the issuer application using its AID (0xA0 0x00 0x00 0x02 0x47 0x10 0x01), then selects the DG1 file (0x01 0x01) and then does a read binary.
SDI011 REFERENCE MANUAL 44 6.3.2. T=CL user command Description This command can be used to send raw data to the user token. 6.3.2.1. Format CLA INS P1 P2 P3 Data 0xFF 0xFE 0x00 0x00 Lraw_data Raw_data 6.3.2.2. Response Data Out PICC response data+ SW1 + SW2 6.3.2.3. Status Words SW1 SW2 Description User should refer to the status words defined by the PICC manufacturer for a description of the status words 6.3.2.4. Example Let‘s consider the Select command defined in ISO7816-4. This command being ISO can be sent to the user token in 2 different ways:  Using the T=CL command  Using the T=CL user command Here are the 2 answers for the select command: The T=CL command is nevertheless more useful for sending commands which are not defined in ISO7816.
SDI011 REFERENCE MANUAL 45 6.4. Set of APDU defined by SCM Microsystems 6.4.1. MIFARE DESFire Commands Description This command can be used to send commands to DESFire-based user tokens. For a description of DESFire commands please contact NXP Semiconductors. 6.4.1.1. Format CLA INS P1 P2 P3 Data 0xFF 0xDE 0x00 0x00 Lcommand Command Response Data Out DESFire response data+ 9000 if the DESFire response data is of single byte DESFire response data if the DESFire response data is more than 1 byte
SDI011 REFERENCE MANUAL 46 6.5. Escape commands for the contactless interface 6.5.1. Sending escape commands to SDI011 A developer can use 2 methods to send escape commands to SDI011 to the contactless interface  SCardControl method defined in PC/SC API  SCardTransmit method defined in PC/SC API in conjunction with the escape command APDU defined earlier in this manual 6.5.2. Escape command codes Escape commands can be used by an application to configure SDI011 to function in a mode that is not its default configured mode or to get specific information. To put the SDI011 back into its default mode, either the SDI011 has to be unplugged and plugged again or the application can send again the same escape command. The following escape commands are supported by SDI011 for the contactless interface. Escape command Code READER_GETCARDINFO 0x11 READER_LEDCONTROL 0x19 READER_CNTLESS_GET_MFRC_REV 0x92 READER_CNTLESS_GET_ATS_ATQB 0x93 READER_CNTLESS_GET_TYPE 0x94 READER_CNTLESS_SET_TYPE 0x95 READER_CNTLESS_RF_SWITCH 0x96 READER_CNTLESS_RAW_CFG 0x97 READER_CNTLESS_RAW_XMIT_EX 0xAE READER_ CNTLESS_DISABLE_PPS 0x99 READER_SWITCH_RF_ON_OFF 0x9C READER_CNTLESS_848KBPS 0x9D READER_CNTLESS_BAUDRATE 0x9E READER_CNTLESS_FORCE_BAUDRATE_PCSC_REV2 0xAD READER_LEDCTRL_BY_FW 0xB2 Sample code to send escape commands can be found in annex.
SDI011 REFERENCE MANUAL 47 6.5.3. READER_GETCARDINFO This escape command is used to get information about the card placed on the reader. The SDI011 returns an error if no card is placed on it. The input buffer shall contain the escape command code Input buffer 0x11 The output buffer contents are described below. Output buffer Value Description B0 0x01 Contactless card present B1 0xNN Baud rate of card-reader communication B2 0xXY X – Upper nibble indicates 0 - memory card 1 - T=CL card 2 - Dual mode card Y – Lower nibble indicates 0 - Type A card 1 - Type B card The Baud rate of card-reader communication 0xNN shall indicate a BYTE as follows b8 b7 b6 b5 b4 b3 b2 b1 0 b1 – 212kbps supported (direction reader to card) b2 – 424kbps supported (direction reader to card) b3 – 848kbps supported (direction reader to card) b5 – 212kbps supported (direction card to reader) b6 – 424kbps supported (direction card to reader) b7 – 848kbps supported (direction card to reader) b8 – 1 – indicates same baud rate in both directions 0 – indicates different baud rates in opposite directions For Example: If 0xNN = 0x77, the card supports all baud rates namely 106, 212, 424 and 848 kbps in both directions. This card can be forced to work at different baud rates in the send and receive directions using the escape command READER_CNTLESS_FORCE_BAUDRATE_PCSC_REV2. If 0xNN = 0xB3, the card supports 106, 212 and 424 kbps in both directions. This card can be made to work only at the same baud rate in the send and receive directions using the escape command READER_CNTLESS_FORCE_BAUDRATE_PCSC_REV2.
SDI011 REFERENCE MANUAL 48 6.5.4. READER_LED_CONTROL_BY_FW This escape command may be used to enable or disable LED control by the firmware. The input buffer is Byte # Value Description B0 0xB2 Escape command code B1 0x00 Disable LED control by FW 0x01 Enable LED control by FW The output buffer is Output buffer NULL 6.5.5. READER_LEDCONTROL This escape command is used to turn ON/OFF the LED. This escape command shall work only if LED control by firmware is disabled. The input buffer shall contain 3 bytes Byte # Value Description B0 0x19 Escape command code B1 0x00 LED number B2 0x00 LED ON 0x01 LED OFF The output buffer is Output buffer NULL 6.5.6. READER_CNTLESS_GET_MFRC_REV This escape message retrieves the revision number of the RF ASIC MFRC531. The input buffer contains the escape command code Input buffer 0x92 The output buffer contains the version of the MFRC531 ASIC.
SDI011 REFERENCE MANUAL 49 6.5.7. READER_CNTLESS_GET_ATS_ATQB This escape command enables the host to retrieve the ATS for Type A T= CL or the ATQB for Type B cards. The input buffer contains the escape command code Input buffer 0x93 The output buffer contains the ATS bytes or the ATQB bytes depending on the type of PICC placed on the reader. 6.5.8. READER_CNTLESS_GET_TYPE This escape command retrieves the type of the card which SDI011 is configured to poll for. The input buffer shall contain the escape command code Input buffer 0x94 The output buffer shall point to a BYTE buffer which will contain the type value coded as Value Description 0x00 Type A 0x01 Type B 0x02 Type A + type B 6.5.9. READER_CNTLESS_SET_TYPE This escape command configures the type of cards SDI011 will poll for. Using this command can improve the polling efficiency of SDI011 for applications where only type A or only type B cards are expected. The default is Type A + type B (0x02). The input buffer shall contain 2 bytes Byte # Value Description B0 0x95 Escape command code B1 0x00 Type A 0x01 Type B 0x02 Type A + type B The output buffer is Output buffer NULL
SDI011 REFERENCE MANUAL 50 6.5.10. READER_CNTLESS_RF_SWITCH This escape command can be used to retrieve/set the RF state of SDI011. The default RF field state is ON. The input buffer shall contain 2 bytes Byte # Value Description B0 0x96 Escape command code B1 0x00 Switch RF Field OFF 0x01 Switch RF Field ON 0xFF Get current field state After the RF is turned off, to turn the RF ON again, card connect shall be done in direct mode. If B1 of the input buffer is 0x00 or 0x01 the output buffer is Output buffer NULL If B1 of the input buffer is 0xFF, the output buffer is a BYTE buffer with 2 possible values Output buffer Description 0x01 RF field is OFF 0x00 RF field is ON 6.5.11. READER_CNTLESS_RAW_CFG This escape command switches SDI011 to raw mode. When SDI011 is in raw mode it only polls for one type of contactless card. SDI011 is by default not in this mode and therefore READER_CNTLESS_RAW_XMIT_EX would fail. The input buffer contains 2 bytes Byte # Value Description B0 0x97 Escape Function code B1 0x00 Type A will be use for further transmissions in raw mode 0x01 Type B will be use for further transmissions in raw mode The output buffer is Output buffer NULL Once SDI011 is in raw mode commands can be sent using READER_CNTLESS_RAW_XMIT_EX escape command.
SDI011 REFERENCE MANUAL 51 6.5.12. READER_CNTLESS_RAW_XMIT_EX This escape command can only be executed by the firmware once SDI011 is put in raw mode using the READER_CNTLESS_RAW_CFG escape command. This escape command can be used to send commands to smart card when SDI011 is in raw mode The input buffer is Byte # Value Description B0 0xAE Escape Function code B1 Wait Time B2 Is CRC required? B3 No of bits per command B4 Card Type 0 – Type A 1 – type B B5 Command length B6 - Bn Command The output buffer contains the response to the command from the offset B6 onwards. The following example uses the raw mode to send a REQB command First, we have to switch the SDI011 into raw mode for type B communication Byte # Value Description B0 0x97 READER_CNTLESS_RAW_CONFIG code B1 0x01 Type B will be used Then, we can send the following bytes to obtain the ATQB response of any type B user token in the field Byte # Value Description B0 0xAE READER_CNTLESS_RAW_XMIT_EX code B1 0x03 FWI is set to 3 B2 0x01 Enable CRC (CRC will be calculated by the RF front end of SDI011) B3 0x00 Number of bits to be sent in the command 0 – Entire byte will be sent B4 0x01 Type B B5 0x03 Command length in bytes B6 0x05 REQB command‘s anti-collision prefix byte B7 0x00 REQB command‘s application family identifier B8 0x01 REQB command parameter with slot number set as 1
SDI011 REFERENCE MANUAL 52 6.5.13. READER_ CNTLESS_DISABLE_PPS By default SDI011 does automatic PPS – i.e. it switches the RF communication speed to the highest possible supported by the card. This escape command can be used to switch ON/OFF automatic PPS. When automatic PPS is OFF, then 106Kbps only is available. The input buffer is Byte # Value Description B0 0x99 Escape command code B1 0x01 Disable Auto-PPS 0x00 Enable Auto-PPS The output buffer is Output buffer NULL 6.5.14. READER_SWITCH_RF_ON_OFF This escape command can be used to switch the RF field ON or OFF when a Contact smart card is inserted into the reader. By default, the RF field is always in the ON state and when any contact smart card is inserted in the reader, the RF field is turned OFF. The input buffer shall contain 2 bytes Byte # Value Description B0 0x9C Escape command code B1 0x00 Switch RF Field OFF when contact card is present in the reader 0x01 Switch RF Field ON when contact card is present in the reader 0xFF Get current field state when Contact smart card is present in the reader After the RF is turned off, to turn the RF ON again, card connect shall be done in direct mode.
SDI011 REFERENCE MANUAL 53 If B1 of the input buffer is 0x00 or 0x01 the output buffer is Output buffer NULL If B1 of the input buffer is 0xFF, the output buffer is a BYTE buffer with 2 possible values Output buffer Description 0x00 RF field is OFF 0x01 RF field is ON 6.5.15. READER_CNTLESS_848KBPS This escape command can be used to enable/disable 848kbps support by SDI011 as well as query whether 848kbps is currently enabled or disabled by SDI011. The RF communication with a user token will only switch to 848Kbps provided the user token supports this baud rate and provided automatic PPS is ON. The input buffer shall contain 2 bytes Byte # Value Description B0 0x9D Escape command code B1 0x00 Disable 848Kbps support 0x01 Enable 848Kbps support 0xFF Get current status on 848Kbps support If B1 of the input buffer is 0x00 or 0x01 then the output buffer is Output buffer NULL If B1 of the input buffer is 0xFF, the output buffer is a BYTE buffer with following possible values Output buffer Description 0x00 848Kbps is disabled 0x01 848Kbps is enabled
SDI011 REFERENCE MANUAL 54 6.5.16. READER_CNTLESS_BAUDRATE This escape command can be used to get the actual operating baud rate of card-reader communication. The input buffer shall contain the escape message value. Input buffer 0x9E The output buffer shall point to a BYTE buffer with following possible values Output buffer Description 0x00 106Kbps in both directions 0x01 106Kbps from PICC to PCD, 212Kbps from PCD to PICC 0x02 106Kbps from PICC to PCD, 424Kbps from PCD to PICC 0x03 106Kbps from PICC to PCD, 848Kbps from PCD to PICC 0x10 212Kbps from PICC to PCD, 106Kbps from PCD to PICC 0x11 212Kbps in both directions 0x12 212Kbps from PICC to PCD, 424Kbps from PCD to PICC 0x13 212Kbps from PICC to PCD, 848Kbps from PCD to PICC 0x20 424Kbps from PICC to PCD, 106Kbps from PCD to PICC 0x21 424Kbps from PICC to PCD, 212Kbps from PCD to PICC 0x22 424Kbps in both directions 0x23 424Kbps from PICC to PCD, 848Kbps from PCD to PICC 0x30 848Kbps from PICC to PCD, 106Kbps from PCD to PICC 0x31 848Kbps from PICC to PCD, 212Kbps from PCD to PICC 0x32 848Kbps from PICC to PCD, 424Kbps from PCD to PICC 0x33 848Kbps in both directions
SDI011 REFERENCE MANUAL 55 6.5.17. READER_CNTLESS_FORCE_BAUDRATE_PCSC_REV2 This escape command can be used to force baud rate for Contactless cards. The input buffer is Byte # Value Description B0 0xAD Escape command code B1 0x00 Apply the baud rate specified by the card 0x01 Force baud rate specified in B2 B2 b0- DR=2 supported, if bit is set to 1 b1- DR=4 supported, if bit is set to 1 b2- DR=8 supported, if bit is set to 1 b3- shall be set to 0, 1 is RFU b4- DS=2 supported, if bit is set to 1 b5- DS=4 supported, if bit is set to 1 b6- DS=8 supported, if bit is set to 1 b7- 1 if the same D is required for both communication directions b8- 0 if different D is supported for each communication direction Encoding of the baud rate to be forced if B1 value is 0x01. No need to send this byte in case B1 has the value =x00 NULL If B1=0x00 The output buffer is Output buffer NULL
SDI011 REFERENCE MANUAL 56 6.6. Escape commands for the contact interface 6.6.1. Sending escape commands to SDI011 A developer can use the following method to send escape commands to SDI011 for the contact interface  SCardControl method defined in PC/SC API 6.6.2. Escape command codes Escape commands can be used by an application to configure SDI011 to function in a mode that is not its default configured mode or to get specific information. To put the SDI011 back into its default mode, either the SDI011 has to be unplugged and plugged again or the application can send again the same escape command. The following escape commands are supported by SDI011 for the contact interface Escape command Code READER_SETMODE 0x01 READER_GETMODE 0x02 READER_APDU_TRANSFER 0x08 READER_SWITCH_SPEED 0x0A READER_SWITCH_PROTOCOL 0x0C READER_DISABLE_PPS 0x0F READER_GETIFDTYPE 0x12 READER_GETINFO_EXTENDED 0X1E 6.6.3. READER_SETMODE This escape command may be used to set the mode of the reader. Applications may call this function, to set the desired mode. Typically, this call is used to switch between the EMV, ISO7816 and the memory card modes of operation. The input buffer is Byte # Value Description B0 0x01 Escape command code B1 0x00 ISO 7816 mode 0x01 EMV mode 0x02 Memory card mode The output buffer is Output buffer NULL
SDI011 REFERENCE MANUAL 57 6.6.4. READER_GETMODE This escape command may be used to retrieve the current mode of the reader. The input buffer is Byte # Value Description B0 0x02 Escape command code The output buffer is Output buffer Description 0x00 ISO 7816 mode 0x01 EMV mode 0x02 Memory card mode 6.6.5. READER_APDU_TRANSFER This escape command may be used to exchange an APDU with the smart card. The input buffer is Byte # Value Description B0 0x08 Escape command code B1- Bn Command APDU The output buffer contains the response APDU. The maximum number of bytes that can be transmitted and received is given below. Transmit: Case 1,2,3 APDU: Max of 256 bytes per APDU Case 4 APDU: Max of 255 bytes per APDU Receive: Max of 259 bytes per APDU
SDI011 REFERENCE MANUAL 58 6.6.6. READER_SWITCH_SPEED In case, when the application is capable of switching the card‘s speed through APDU (if the card supports such a feature), this escape command is used to inform the reader about the speed change occurred between application and card. The first byte will contain the escape function value; the next two bytes contain Fi and Di respectively. The output buffer field shall be NULL. The input buffer is Byte # Value Description B0 0x0A Escape command code B1 Fi value B2 Di value The output buffer is Output buffer NULL 6.6.7. READER_SWITCH_PROTOCOL In case, when the application is capable of switching the card‘s protocol through APDU (if the card support such a feature), this escape command is used to inform the reader about the protocol change occurred between application and card. The input buffer is Byte # Value Description B0 0x0C Escape command code B1 0x00 T0_PROTOCOL 0X01 T1_PROTOCOL The output buffer is Output buffer NULL
SDI011 REFERENCE MANUAL 59 6.6.8. READER_DISABLE_PPS This escape command disables the automatic PPS done by the firmware. The input buffer is Byte # Value Description B0 0x0F Escape command code B1 0x00 Enable PPS 0X01 Disable PPS The output buffer is Output buffer NULL 6.6.9. READER_GETIFDTYPE This escape command is used to get the current IFD type from the reader. The first byte of the input buffer contains the escape id value. The reader gets the value from the reader capability structure, which is implemented in the reader as a configurable item. The output buffer shall point to a WORD buffer. The IFD type of SDI011-Generic is 0x010E, The input buffer is Byte # Value Description B0 0x12 Escape command code
SDI011 REFERENCE MANUAL 60 6.6.10. READER_GETINFO_EXTENDED This escape command is used to get the information of the reader like the major and minor version of the firmware, capabilities of the reader and the Unicode serial number. The output buffer shall point to an application allocated SCARD_READER_GETINFO_PARAMS_EX structure mentioned below. The input buffer is Byte # Value Description B0 0x1E Escape command code typedef struct __SCARD_READER_GETINFO_PARAMS_EX { OUT BYTE byMajorVersion; OUT BYTE byMinorVersion; OUT BYTE bySupportedModes; // 0 – ISO7816, 1 – EMV, 2 – Memory card OUT WORD wSupportedProtocols; // 1 – T=0; 2 - T=1; 3 – T=0 & T=1 OUT WORD winputDevice; OUT BYTE byPersonality; OUT BYTE byMaxSlots; OUT BYTE bySerialNoLength; OUT BYTE[28] bySerialNumber; }SCARD_READER_GETINFO_PARAMS_EX, *PSCARD_READER_GETINFO_PARAMS_EX;
SDI011 REFERENCE MANUAL 61 7. Annexes 7.1. Annex A – Status words table SW1 SW2 Description 0x90 0x00 NO ERROR 0x67 0x00 LENGTH INCORRECT 0x6D 0x00 INVALID INSTRUCTION BYTE 0x6E 0x00 CLASS NOT SUPPORTED 0x6F 0x00 UNKNOWN COMMAND 0x63 0x00 NO INFORMATION GIVEN 0x65 0x81 MEMORY FAILURE 0x68 0x00 CLASS BYTE INCORRECT 0x69 0x82 Command not allowed, security status not satisfied 0x6A 0x81 FUNCTION NOT SUPPORTED 0x6B 0x00 WRONG PARAMETER P1-P2
SDI011 REFERENCE MANUAL 62 7.2. Annex B – Sample code using escape commands through Escape IOCTL File Name : T_hbr.H #ifdef __cplusplus extern "C" { #endif #define IOCTL_CCID_ESCAPE SCARD_CTL_CODE (0xDAC) #define CCID_GET_848KBPS_STATUS 0xFF9D #define CCID_SET_848KBPS_ON 0x019D #define CCID_SET_848KBPS_OFF 0x009D #define MINTIMEOUT 300 #ifdef __cplusplus } #endif File Name : T_hbr.CPP #include <windows.h> #include <winbase.h> #include <stdio.h> #include <conio.h> #include "winscard.h" #include "winerror.h" #include "T_hbr.H" VOID main(VOID) { SCARDCONTEXT ContextHandle; SCARDHANDLE CardHandle; BYTE OutByte; WORD InWord,i; DWORD ActiveProtocol; /* ICC protocol */ ULONG InBufLen,ResLen; ULONG ret;
SDI011 REFERENCE MANUAL 63 SCARD_READERSTATE Reader[1]; // please add the name of the used reader here or use SCardListReaders // to find the right reader name char *ReaderName[] = {"SCM Microsystems Inc. SDI011 Contactless Reader 0", NULL}; /********************************************************************************************************/ ContextHandle = -1; ret = SCardEstablishContext(SCARD_SCOPE_USER, NULL, NULL, &ContextHandle); if (ret == SCARD_S_SUCCESS) { ret = SCardConnect( ContextHandle, ReaderName[0], SCARD_SHARE_SHARED, SCARD_PROTOCOL_T0 | SCARD_PROTOCOL_T1, &CardHandle, &ActiveProtocol); if (ret == SCARD_S_SUCCESS) { /* get actual 848kbps status: ON/OFF */ InBufLen = 2; InWord = CCID_GET_848KBPS_STATUS; ret = SCardControl (CardHandle, IOCTL_CCID_ESCAPE, &InWord, InBufLen, &OutByte, 1, &ResLen); printf ("\n Get 848kbps status: %lx: %.2x", ret,OutByte); Reader[0].dwCurrentState = SCARD_STATE_UNAWARE; Reader[0].dwEventState = SCARD_STATE_UNAWARE; Reader[0].szReader = ReaderName[0]; ret = SCardGetStatusChange( ContextHandle,
SDI011 REFERENCE MANUAL 64 MINTIMEOUT, Reader, 1); printf ("\nATR: "); for (i=0; i<Reader->cbAtr; i++) { printf ("%.2x ",Reader->rgbAtr[i]); } printf ("\n----------------------------------------------\n"); /* enable 848KBPS: ON */ printf ("\nEnable 848kbps "); InBufLen = 2; InWord = CCID_SET_848KBPS_ON; ret = SCardControl (CardHandle, IOCTL_CCID_ESCAPE, &InWord, InBufLen, &OutByte, 1, &ResLen); ret = SCardDisconnect(CardHandle, SCARD_RESET_CARD); ret = SCardConnect (ContextHandle, ReaderName[0], SCARD_SHARE_SHARED, SCARD_PROTOCOL_T0 | SCARD_PROTOCOL_T1, &CardHandle, &ActiveProtocol); /* get actual 848KBPS status: ON/OFF */ InBufLen = 2; InWord = CCID_GET_848KBPS_STATUS; ret = SCardControl (CardHandle, IOCTL_CCID_ESCAPE, &InWord, InBufLen, &OutByte, 1, &ResLen);
SDI011 REFERENCE MANUAL 65 printf ("\n Get 848kbps status: %lx: %.2x", ret,OutByte); Reader[0].dwCurrentState = SCARD_STATE_UNAWARE; Reader[0].dwEventState = SCARD_STATE_UNAWARE; Reader[0].szReader = ReaderName[0]; ret = SCardGetStatusChange (ContextHandle, MINTIMEOUT, Reader, 1); printf ("\nATR: "); for (i=0; i<Reader->cbAtr; i++) { printf ("%.2x ",Reader->rgbAtr[i]); } printf ("\n----------------------------------------------\n"); /* Disable 848Kbps: OFF */ printf ("\nDisable 848KBPS "); InBufLen = 2; InWord = CCID_SET_848KBPS_OFF; ret = SCardControl(CardHandle, IOCTL_CCID_ESCAPE, &InWord, InBufLen, &OutByte, 1, &ResLen); ret = SCardDisconnect(CardHandle, SCARD_RESET_CARD); ret = SCardConnect(ContextHandle, ReaderName[0], SCARD_SHARE_SHARED, SCARD_PROTOCOL_T0 | SCARD_PROTOCOL_T1, &CardHandle, &ActiveProtocol); /* get actual 848KBPS status: ON/OFF */ InBufLen = 2; InWord = CCID_GET_848KBPS_STATUS; ret = SCardControl(CardHandle, IOCTL_CCID_ESCAPE, &InWord, InBufLen, &OutByte, 1, &ResLen); printf ("\n Get 848KBPS status: %lx: %.2x", ret,OutByte); Reader[0].dwCurrentState = SCARD_STATE_UNAWARE; Reader[0].dwEventState = SCARD_STATE_UNAWARE;
SDI011 REFERENCE MANUAL 66 Reader[0].szReader = ReaderName[0]; ret = SCardGetStatusChange(ContextHandle, MINTIMEOUT, Reader, 1); printf ("\nATR: "); for (i=0; i<Reader->cbAtr; i++) { printf ("%.2x ",Reader->rgbAtr[i]); } printf ("\n----------------------------------------------\n"); ret = SCardDisconnect(CardHandle, SCARD_RESET_CARD); } else { printf("\n SCardConnect failed with 0x%.8lX",ret); } ret = SCardReleaseContext(ContextHandle); } else { printf("\n SCardEstablishContext failed with %.8lX",ret); } printf("\npress any key to close the test tool\n"); getch(); }
SDI011 REFERENCE MANUAL 67 7.3. Annex C - SCM Proprietary CLA bytes CLA Byte Function 0xF0 Contact Memory cards 0xFF MIFARE-TCL Switching T=CL User command Escape command APDU The second SCM Proprietary APDU is blocked for the application layer. This is used for internal communication i.e. between the driver and the firmware. Function CLA byte – PC/SC1.0 CLA byte – PC/SC2.0 T=CL User Command APDU 0xFC 0xFF MIFARE DESFire APDU 0xFC 0xFF Escape Command APDU 0xFD 0xFF In order to maintain compatibility with some customer applications which use the CLA bytes of PC/SC 1.0 architecture, the following switching mechanism can be used. Option1: Use the CLA byte of PC/SC1.0 architecture Option2: Use the CLA byte of PC/SC2.0 architecture The above two options can be controlled by  Configuring the firmware  INF/registry entry  Vendor IOCTL. By default, option #2 is set in the firmware binary. The entry System\CurrentControlSet\Services\SCM\ProprietaryAPDUOption is kept disabled in the INF by default. Enabling this key and setting this entry to 0 will override the firmware setting with option #1. Enabling this key and setting this entry to 1 will override the firmware setting with option #2. Vendor IOCTL_SWITCH_PROPRIETARY_APDU_OPTION (0x856) can also be used to switch between the two options. Input buffer with value 0x00 will switch to option#1 and input buffer with value 0x01 will switch to option#2.
SDI011 REFERENCE MANUAL 68 7.4. Annex D – Mechanical drawings 7.4.1. Top Casing
SDI011 REFERENCE MANUAL 69 7.4.2. Bottom Casing
SDI011 REFERENCE MANUAL 70 7.4.3. Stand

Navigation menu