Imation TDKA73 TDK WIRELESS BOOMBOX User Manual Usermanual
Imation Corp. TDK WIRELESS BOOMBOX Usermanual
Imation >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1727960 |
| Application ID | j/yUg6VRBi9eQ3d7rJaUBw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 17.54kB (219258 bits) |
| Date Submitted | 2012-06-21 00:00:00 |
| Date Available | 2012-06-21 00:00:00 |
| Creation Date | 2012-06-22 11:59:57 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2012-06-22 11:59:57 |
| Document Title | Usermanual.pdf |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | olic |
2. Connect the AC power adapter jack to the DC IN jack W on the rear of the unit and then connect the plug to a 100V-240V wall outlet. 1. Carrying Handle 2. Power/Volume Control 3. Display 4. Source/Select Control 5. Remote Sensor LOCATION OF CONTROLS Replacing the Remote Control Battery: 1. Remove the Battery Compartment by pressing in on the tab and then sliding the compartment out. 2. Install a CR2025 battery, paying attention to the polarity diagram in the compartment (positive side up). 3. Replace the Battery Compartment. Rechargeable Battery Notes: t &BDI UJNF ZPV DIBSHF BOE EJTDIBSHF UIF CBUUFSZ DIBSHF DZDMFT CBUUFSZ DBQBDJUZ slightly diminishes. Rechargeable batteries have a limited number of charge cycles and need to be replaced eventually. t :PVNBZXJTIUPSFQMBDFZPVSCBUUFSZXIFO PSCFGPSF UIFCBUUFSZEPFTOPUTVQQMZFOPVHI power to operate your device. Also, proper disposal is essential from environmental and safety point of view. Putting any battery directly in the trash will harm the environment. t %POPUJODJOFSBUF Replacing the Rechargeable Battery: If the battery does not supply enough power (see note in Rechargeable Battery Notes box below), replace the rechargeable battery as follows: 1. Remove the screws on the bottom of the unit and remove the bottom plate. 2. Unplug the rechargeable battery and replace with battery pack with the following specs, (xxxxx,xxxxx,xxxxx ADVISE SPECS) 3. Replace the bottom plate and tighten the screws. Notes: t 0OMZVTFUIFTVQQMJFE"$BEBQUFS t 3FNPWFCPUIUIF%$QMVHBOE"$*/QMVHUPEJTDPOOFDU"$BEBQUFSXIFOOPUJOVTF t %JTDPOOFDUUIF"$DPSEUPVTFXJUI%$QPXFS SFDIBSHFBCMFCBUUFSZ This unit has a built-in rechargeable battery that will automatically be charged as long as the unit is plugged in. When charging, the Battery indicator will light red. When fully charged, the indicator will turn off. If the battery is low, the Battery indicator will fade in and out in a red hue. Note: The battery will provide approximately 6 hours of operation at 50% volume or 2 hours at 100% volume. US AC Plug Shown 1. Select the appropriate plug for your country and connect it to the AC power adapter. AC CONNECTION / RECHARGING THE BATTERY FM AM 17 18 21 20 19 OFF Button Power Button Bluetooth Button SEEK Buttons AUX Button 17. 18. 19. 20. 21. FM Button AM Button Mute Button Volume Buttons Preset Buttons OPERATION Press one of the Mode buttons (Bluetooth, AUX, FM or AM) to access the respective mode. 12. 13. 14. 15. 16. 11 10 Using a Bluetooth Device 1. Turn the unit on; the previously listened to source and volume will be selected. 2. With a unit paired (see previous section), press the Source/Select control x once so all the modes light. Rotate the Source/Select control x to the Bluetooth ( )position to select the Bluetooth mode. 3. Operate your bluetooth device and its sound will be heard through this unitâs speakers. 4. Adjust the volume using the Power/Volume control v on this unit, or the Volume Pairing a Bluetooth Device 1. Turn the unit on; the previously listened to source and volume will be selected. 2. Press the Source/Select control x once so all the modes light. Rotate the Source/ Select control x to the Bluetooth ( ) position to select the Bluetooth mode. 3. Press and hold the Source/Select control x for approximately 3 seconds until the Bluetooth indicator blinks quickly to make the speaker âdiscoverableâ. 4. On the bluetooth device, enable bluetooth and select âA73â from the Device List. If the bluetooth device asks for a passkey, use â0000â. Some bluetooth devices will ask you to accept the connection. If the units are paired properly, the speaker will beep and the Bluetooth indicator will light solid. If it failed, the Bluetooth indicator will blink slowly. Note: After you pair a device, this unit will remember it for future use. Turning the Unit On and Off: 1. The main power switch is on the rear of the unit. Slide to the ON position to turn the unit on and activate the Power/Volume control on the main unit and the Power button on the remote. 2. Once the main power switch is turned on, you can turn the unit on or off by pressing the Power/Volume control v on the main unit. If using the remote, press the Power button am to turn the unit on. Press the OFF button al to turn the unit off. AUX Jack (Rear of Unit) Insert one end of an audio cable (not included) into the LINE OUT jack on your external audio unit and the other end into the AUX jack U on the rear of this unit. To listen to the external audio unit, turn this unit on and turn on the external unit as well. Press the Source/Select control x once so all the modes light. Rotate the Source/Select control x to the AUX position to select the Line In mode. Start playback of the external unit and the external audio unitâs output sound will be heard through this unitâs speakers. Headphone Jack (Rear of Unit) For private listening, simply plug headphones into the Headphone jack X on the rear of this unit. The speakerâs sound will be muted when headphones are inserted. AUX OFF 9. Headphone Jack 10. AM Antenna Jack 11. USB CHARGE Jack LOCATION OF CONTROLS (CONTINUED) AUX Jack Main Power (OFF/ON) Switch DC IN Jack 14 15 16 12 13 6. 7. 8. Wireless Boombox User Guide OPERATION (CONTINUED) Output Power ............. . 7W x 2 + 15W (subwoofer) Wireless Audio ......Bluetooth version 2.1-A2DP profile Line-input Audio ................ 3.5mm stereo jack up to ...............................................2.5Vrms input signal USB Port.............................5 V @ 2.1 A charge only RADIO SECTION: Frequency Range (FM)....................... 87.5-108MHz Frequency Range (AM) ..................... 530-1710KHz 63952712-A The TDK Life on Record Logo is a trademark of TDK Corporation and is used under license. All other trademarks and logos are property of their respective owners. Specifications are subject to change without notice. GENERAL: Power Source ........DC 18V, 2A Adapter (Center Pos.) Power (DC) .........Internal NiMH rechargeable battery Dimensions .......... .17 (W) x 11.5 (H) x 4 (D) inches Weight .. ....................................................... XXXlbs Speakers.........2 x 2 inch full-range drivers, 1 x 5.25 ....... inch subwoofer, 2 x 5.25 inch passive radiators SPECIFICATIONS AND COMPATIBILITY Auto Power Off If the unit has no audio signal, and/or a USB device is not charging, for 20 minutes, the unit will turn itself off. Setting the EQ and Bass 1. Press the Source/Select control x once so all the modes light. Rotate the Source/ Select control x to the BAS (Bass) or TRE (Treble) position. 2. Adjust the setting using the Volume/Power control v. Note: If no setting has taken place for five seconds, the unit will exit the Bass/Treble setting mode and will revert to the previous mode. Changing the FM region This unit allows you to set the desired radio region as follows: With the power on, press and hold the Volume/Powerv and Source/Selectx controls simultaneously for at least four seconds to enter the radio region setting mode. Scroll through the menu using the Source/Select control x to select the desired region, then press the Source/Select x control to confirm. When finished, scroll using the Source/Select control x to select âEXITâ, then press the Source/Select control x. Region 1 â United States (87.5MHz to 108MHz) Region 2 â Europe (87.5MHz to 108MHz) Region 3 â Japan (76MHz to 108MHz) Setting the FM Presets 1. Turn the unit on and select a station as described in steps 1 through 3 above. 2. Press and hold the desired Preset button bk on the remote control for three seconds. The Preset number will blink three times in the display to confirm setting. 3. To call up a preset, simply press and release the Preset number bk on the remote control. Using the AM or FM Radio 1. Rotate the Volume/Power control v to turn the unit on; the previously listened to source and volume will be selected. 2. Press the Source/Select control x once so all the modes light. Rotate the Source/ Select control x to the AM or FM position to select the radio mode. 3. When AM or FM appears in the display, the unit is in Tuner mode, so use the Source/ Select control x to select a station. If all the indicators appear around the Source/ Select control, the unit is in Select mode; in this case press the Source/Select control x to make it operate as a tuning control. 4. To have the unit automatically scan for the next strong station, press the SEEK Up or Down button ao on the remote control. 5. Adjust the volume using the Volume/Power control v and adjust the Bass and Treble as described later in this guide. 6. To select another source, press the Source/Select control x to enter the Select mode and make it operate as a source selector. 7. To mute the sound, press the Mute button as on the remote control. AM Antenna: Insert the AM Antenna plug into the AM Antenna jack on the rear of the unit for best AM reception. Assemble the stand by rotating and inserting the tabs until they click. Charging a Bluetooth Device with this Unit On the rear of this unit is a USB jack that can be connected to a USB device, which will charge if the unit is connected to AC power. control on the Bluetooth device, and adjust the Bass and Treble as described later in this guide. 5. To mute the sound, press the Mute button as on the remote control. IMPORTANT: After step 2, you have two minutes to pair the units. TDKperformance.eu A73 Please read these instructions completely before operating this product Greg, The contact info is on the second page. Wireless Boombox User Guide Wireless Boombox THIS WILL GO AT THE END OF THE MANUAL -------------------------- TDKperformance.eu A73 Please read these instructions completely before operating this product US ....................................................................................................800-285-2783 DE/AT/CH ...................................................................................+49 2131 226 311 IT ...............................................................................................+39 022 1043 818 ES/PT ...........................................................................................+34 900 993 166 UK/IE...................................................................................... +44 (0)1344 402201 NL/Other EU ............................................................................ +31 (0)23 521 2605 SG ....................................................................................................65-6499-7199 AU/NZ .................................................................................................800-225-013 JP .....................................................................................................0120-81-0536 CN ................................................................................................8621-6121-2122 KR.......................................................................................................02-2012-999 HK...................................................................................................852-2161-2888 Technical Assistance Assistance technique Technische Hilfe Technische assistentie Assistenza tecnica Asistencia tĂŠcnica AssistĂŞncia tĂŠcnica Đ˘ĐľŃ Đ˝Đ¸ŃĐľŃĐşĐ°Ń ĐżĐžĐźĐžŃŃ Pomoc techniczna TechnickĂĄ pomoc á˘âžá¨ĽáĽ´ ὤă ㍴ă VáĄă¸¨áŹá§áĄá´ŕ¤¤ŕĄžÎ ëą ëŠęëŠęŹë¤ęĄęťš7'./R5ęŠĄę˝şęľ ęŤëę˛ę˝ëśĄéĄë˛ëšéśęëľę éť ëŞ ééęŠśé˛Šę˛ ZZZLPDWLRQFRNU ă°ăâ°ć°¨äžăŚćŁâťâ ć°¨äžâŚĺąĄĺä¤ć˘ĺŁŽĺžăâłă˘˘ă ˛âŤ,,㌎⡌㲢 ZZZLPDWLRQFRPKN ă°ăâ°á§¤âä᧼ăŚćŁâťâ âźâŚâäăăťâä˝äâźćžâäĺ澧⎜âľâ¸ł ZZZLPDWLRQFRPFQ áážáááá㪚ăâŠäŻ á˝ ă¨âťćäĺťâäŻâ¸˝â槥âźááááá°á ZZZWGNPHGLDMS Imation ANZ Pty Ltd Unit 2, 1 Coronation Avenue Kings Park, NSW 2148 www.tdkperformance.com.au Imation Singapore Pte. Ltd. Unit 02-02 New Tech Park 151 Lorong Chuan Singapore 556741 www.tdk-media.com.sg Imation Europe B.V. Siriusdreef 46-52 2132 WT Hoofddorp The Netherlands www.tdkperformance.eu Imation Enterprises Corp. 1 Imation Way, Oakdale, MN 55128-3414 USA www.tdkperformance.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2012:06:22 11:59:57+08:00 Modify Date : 2012:06:22 11:59:57+08:00 Metadata Date : 2012:06:22 11:59:40+08:00 Creator Tool : PScript5.dll Version 5.2.2 Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 12357 bytes, use -b option to extract), (Binary data 5878 bytes, use -b option to extract) Document ID : uuid:EF7554B11EBCE111A15DACA7A756735A Instance ID : uuid:f9fca770-8dd4-4d3d-9f99-498caa71117b Derived From Instance ID : uuid:35e7c4cd-a5ee-1946-a963-57b7b240048e Derived From Document ID : xmp.did:1C9CF0ED072068118C14E1BAB9907164 Derived From Rendition Class : proof:pdf Doc Change Count : 12393 Format : application/postscript Title : Usermanual.pdf Creator : olic Page Count : 2 Author : olicEXIF Metadata provided by EXIF.tools