Infinition BR-1022 BR-1022 Doppler Radar User Manual BR1022 July 30 2004

Download:
Mirror Download [FCC.gov]
Document ID	477310
Application ID	bn7U9FEy9YWNxwHbEC9p5g==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.88kB (185947 bits)
Date Submitted	2004-10-08 00:00:00
Date Available	2004-10-08 00:00:00
Creation Date	2004-07-30 12:34:55
Producing Software	Acrobat PDFWriter 4.0 for Windows NT
Document Lastmod	2004-07-30 12:37:02
Document Title	BR1022 User Manual July 30 2004
Document Creator	Microsoft Word - BR1022 User Manual July 30 2004
Document Author:	Jean-Luc Gagnon

BR-1022
User Manual
Rev. 02
!
Important Safety Instructions
1. Carefully read all of the instructions provided and save them for later use. Heed all
warnings and instructions marked on the BR-1022.
2. Do not place the BR-1022 on an unstable stand or surface as it may fall resulting in
serious damage.
3. The BR-1022 must be operated from a 120 Volts AC 60Hz @ TBDA power source
for the North America model, or from a 240 Volts AC 50Hz @ TBDA power source
for the European model. Operating voltage is factory set.
4. The BR-1022 power cord is equipped with a three-prong grounding plug that will
only fit into a grounding type power outlet. This is a safety feature. If you are unable
to insert the plug into the outlet, contact a qualified person to replace the obsolete
outlet. Do not tamper with the grounding prong to force fit into the outlet.
5. Do not allow any objects to rest on the power cord or place the BR-1022 where the
power cord will be trampled on.
6. If an extension cord is used with the BR-1022, make sure that the total ampere ratings
of the devices plugged into the extension cord do not exceed the extension cord
ampere rating.
7. Warning: No operator serviceable parts inside the BR-1022 radar unit. Please refer
servicing to service qualified personnel.
1. General
The BR-1022 radar can be used to measure the radial velocity of any moving object located in the
radar beam coverage. The output of the radar is an analog signal with a frequency and amplitude
proportional to the radial velocity and distance of the moving object.
2. Microwave Safety Warning
Based on limits specified by the Federal Communication Commission (FCC) on
Radio Frequency (RF) emissions in a general population environment,
continued exposure to radiation should be avoided within 4.0 meter in front of
the radar. Radiation levels outside this region fall within regulations of 1
mW/cm2 and are not considered safety hazards. When setting up the antenna,
special care should be taken to avoid situations where the antenna radiates
towards individuals. The antenna should be positioned such that bystanders are
located behind the antenna. During antenna setup, the antenna power cord
should be unplugged to avoid accidental hazardous exposures to radiations.
Always turn the antenna transmitter off during periods of inactivity. Direct
visual contact with the radar when transmitting should be avoided at all times.
3. Specifications
Description
Nominal Frequency
Nominal Transmitting Power
Antenna Gain
Transmitter Stability
Beamwidth
Dimension (without yoke)
Specification
10.525 GHz
2.0 W – 0.1 W, selectable
27 dBi (nominal)
±5 ppm
4° x 4°
30.75” x 15.25” x 3.00”
4. Installation
The BR-1022 is mounted on a yoke that has a 3/8”-16 hole for installation on a tripod. The yoke
provides the flexibility for radar alignment in both azimuth and elevation.
5. Operation
The BR-1022 is powered on 120/240 VAC, 50-60 Hz using a conventionnal power cord for
connection in standard power outlet. It is interfaced to a processing unit using a single four-wire
cable equipped with military connectors. This cable is used to carry out the radar Doppler signal
to the processing unit and the antenna transmission control. You should connect your radar cable
from this connector to the appropiate radar input on your processing unit.
The radar head has an override transmitter control switch that can be used to activate the
transmitter locally at the antenna.
In addition, the radar has a transmitter power control switch to select between low or high output
power. At the low setting, the transmitter output power is 0.1 Watt and at the high setting, the
output is 2.0 Watts.
The BR-1022 has three LED indicators, one for the main power, one for the transmitter on/off
status and the one for the transmitter output power selection (low or high).
Also, the BR-1022 has a provision for connecting a 12 VDC (2 amperes maximum) warning
device. The warning device is automatically enabled when the radar transmitter is switched on.
This safety feature is useful to warn bystanders when the radar is radiating.
6. Maintenance
The BR-1022 radar does not require much maintenance. Attention should however be paid to a
few points:
Keep the connectors clean from dirt and moisture to avoid corrosion and bad connections.
Now and then wipe the radar enclosure and antenna panels with a soft and wet cloth.
The radar fuses are located inside the radar unit. To replace them, refer the radar system to
qualified personnel.
Warning: No operator serviceable parts inside the radar unit. Please refer
servicing to service qualified personnel
7. Power Connector Specification
Connector type: Amphenol T3110-000
Pin
Description
AC Neutral
120Vac
240Vac
Protective ground
8. Antenna Connector Specification
Connector type: ITT CANNON MS3124E16-8P
Pin
Description
Not Connected
Not Connected
Not Connected
Remote Make for Antenna Transmitter Control (+ 5 Vdc Output)
Make Ground
Doppler Signal + (5 Vpp max.)
Doppler Signal - (5 Vpp max.)
Ground
The processor does the remote activation of the transmitter by short circuiting pins D and E of the
connector.
9. Antenna Warning Device Connector Specification
Connector type: ITT CANNON MS3124E12-3S
Pin
Description
12 Vdc, 2 amperes maximum
Not Connected
Ground
LIMITED WARRANTY. Infinition Inc. products are warranted against defects in
materials and workmanship for a limited period of time from the date Infinition Inc. ships
the products to the customer as follows: interface hardware (one (1) year); cables, cable
reels, radar antennas and acoustic sensors (ninety (90) days); and software medium
(ninety (90) days). All software products sold by Infinition Inc. are licensed to the
customer under the terms of the product software license agreement. Replacement
products will be warranted for the longer of, the remainder of the original warranty
period or thirty (30) days. Expenses for shipment of repaired or replacement products to
and from Infinition Inc. shall be the responsibility of the customer. After examining and
testing a returned product, if Infinition Inc. concludes that the product is not defective,
the customer will be notified and the product will be returned to the customer with an
additional charge for shipping, examination and testing. This limited warranty is void if
failure of the products has resulted from accident, abuse, misuse, improper hardware
connection or unauthorized maintenance or repair.
CUSTOMER REMEDIES. The sole obligation of Infinition Inc. (and the customer’s
sole remedy) with respect to this warranty shall be to, as its option, return fees paid or
repair/replace any defective products, provided that Infinition Inc. received a written
notice of such defects during the application of this warranty period.
RETURN/CANCELLATION POLICY. The customer may return unwanted products
within twenty (20) days of the delivery date. A twenty percent (20%) restocking fee shall
be charged to the customer on any returned product. Infinition Inc. reserves the right to
cancel any order if the customer representations to Infinition Inc. are false or misleading.
THE PRODUCTS ARE PROVIDED “AS-IS” WITHOUT WARRANTY OF ANY
KIND, AND NO OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED
ARE MADE WITH RESPECT TO THE PRODUCTS, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. INFINITION INC. DOES NOT
WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS
REGARDING THE USE OF, OR THE RESULTS OF THE USE OF THE
PRODUCTS IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY, OR
OTHERWISE AND DOES NOT WARRANT THAT THE OPERATION OF THE
PRODUCTS WILL BE ININTERRUPTED OR ERROR FREE.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. To the maximum extent
permitted by applicable laws, in no event shall Infinition Inc. be liable for any damages,
including, but not limited to, any special, direct, indirect, incidental, exemplary, or
consequential damages, expenses, lost profits, lost savings, business interruption, lost
business information, or any other damages arising out of the use or inability to use the
products, even if Infinition Inc. has been advised of the possibility of such damages.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Creator                         : Microsoft Word - BR1022 User Manual July 30 2004
Create Date                     : 2004:07:30 12:34:55
Title                           : BR1022 User Manual July 30 2004
Author                          : Jean-Luc Gagnon
Producer                        : Acrobat PDFWriter 4.0 for Windows NT
Modify Date                     : 2004:07:30 12:37:02-04:00
Page Count                      : 6

EXIF Metadata provided by EXIF.tools