Ingersoll Rand SXG6701K Card Reader User Manual 24105645 Card Reader Maunal SXG6701K

Download:
Mirror Download [FCC.gov]
Document ID	1788617
Application ID	DzOFabuyFK8VamapZWgGUg==
Document Description	PCRSXG6701K_User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.82kB (135295 bits)
Date Submitted	2012-09-12 00:00:00
Date Available	2012-09-18 00:00:00
Creation Date	2012-08-14 14:55:08
Producing Software	Acrobat Distiller 9.3.0 (Windows)
Document Lastmod	2012-08-14 14:55:08
Document Title	24105645-Card Reader Maunal SXG6701K.pdf
Document Creator	Microsoft® Word 2010
Document Author:	zhenyusong

SXG6701K
Installation Guide
SCHLAGE
TESTING THE READER
1.
Power up the reader. The LED will light followed by a beeper tone.
This indicates that the reader is ready.
Ingersoll Rand Security Technologies
10F, Tower B, City Center of Shanghai,
2.
100 Zun Yi Road, Shanghai 200051, P.R. China
and a green LED flash will indicate successful operation. Note that a red
Tel:+86 21 22081288
Present a proper card or token programmed to operate the reader
flash could simply indicate an incorrect match or miss-programmed
Fax:+86 21 62371991
card/token rather than a faulty reader installation.
Web: www.irco.com.cn
ADDITIONAL NOTES
PARTS LIST
1-Installation sheet 1-Mounting Plate 1-Potted Reader Assembly
The voltage specification for these readers is 8-16 volts.
2-Mounting Screws 1-Cover
Typical cable gauge ranges from 18 to 22 gauge. Check with your
1- Cover Assembly Screws
MOUTING THE READER
cable supplier to determine the best choice for your application and
1.
installation distance.
Determine an appropriate mounting position on a single gang box or
well. Be sure to account for any applicable ADA height requirements.
SPECIFICATIONS
2.
Power Supply: DC
the single gang box using the screws provided.
Voltage Range: 8-16 V DC
3.
For a wall mount, drill two mounting holes between 1.57”(40mm)
Temperature Range:
and 2.83”(72mm) apart on the mounting surface. Drill one 0.59”(15mm)
Card Reader Distance: Up to 76.2mm–distance can vary widely
diameter cable hole for the pigtail wire connection.
depending on installation conditions and credential type.
4.
Connect the mounting plate to the wall using the screws provided.
5.
Wire the unit according to the color code chat below ensuring that all
-150m. maximum @22 AWG and 12V
For a single gang box mount, attach the black –plate to the holes in
connections are made through the center hole in the mounting plate.
-35ć to 67ć (-31F to 152F)
Cable Distance to Panel in Wiegand ËŠode:
-60m. maximum @22 AWG and 8V
Information Output: Wiegand format
plate.
Regulatory Approvals and Standards:
7.
UL294, ISO15693, ISO14443A/B, Europe: CE listed.
6.
Hook the top of the potted case assembly to the top of the mounting
Swivel the unit down into place and snap the cover over the potted
reader assembly.
FCC STATEMENT
8.
The FCC requires the following statement for your information: This
Install the Screw from the bottom to fix the cover to the potted case
device complies with Part15 of the FCC Rules. Operation is subject to the
to the mounting plate.
PP
> @
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
PP
> @
PP
> @
PP
> @
interference that may cause undesired operation.
This reader utilizes and radio frequency energy and has been tested and
complies with the limits of FCC testing. Changes, modifications or
disregard of proper installation instructions not expressly approved by
Ingersoll Rand Corporation is strictly prohibited by the FCC and could
void the user’s authority to operate the equipment.
Figure 2 SXG6701k cable connections
PP
> @

CABLE CONNECTIONS
1.
Ingersoll Rand’s SXG6701K readers are supplied with a 12 color
conductor cable pigtail. Connect this pigtail with the host/panel being
careful to match the color of each wire with the chart shown in Figure 1.
2.
Use a DC power source between 8 volts and 16 volts.
3.
Be sure the reader is properly grounded by attaching the ground
wire to an earth ground connection at the power supply or panel end of
the cable.
Green
Date 0
White
Data 1
Light Blue
Green LED
Brown
Red LED
Red
Power+ DC(8-16VDC)
Black
Ground
Yellow
Beeper
Tan
Tamper Output
PinkˈGray, Purple, Blue
Not Used
Warning˖ Connect wires strictly in accordance with the above wiring.
Recommend cut off the metal wires of unused in field installation.
Copyright Š2012, Schlage. All rights reserved.
24105645-Rev.A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : zhenyusong
Create Date                     : 2012:08:14 14:55:08+08:00
Modify Date                     : 2012:08:14 14:55:08+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : Microsoft® Word 2010
Producer                        : Acrobat Distiller 9.3.0 (Windows)
Format                          : application/pdf
Creator                         : zhenyusong
Title                           : 24105645-Card Reader Maunal SXG6701K.pdf
Document ID                     : uuid:40f687a4-c9e5-4200-bea5-2a98df282ee2
Instance ID                     : uuid:71b0855a-9cb1-49e7-9b6b-69aff63d280e
Page Count                      : 1

EXIF Metadata provided by EXIF.tools