InnoComm Mobile Technology 1901 3.5G data card User Manual
InnoComm Mobile Technology Corporation 3.5G data card
User manual
InnoComm Mobile Technology Corp. Amazon Modem Module Development Kit User Manual Version 1.1 Editor: Cathy Lee [挑選日期] Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 TABLE OF CONTENT 1. INTRODUCTION ...................................................................................... 3 1.1. DEVELOPMENT KIT CONTENT ................................................................. 3 1.2. AMAZON MODEM MODULE AND EXTENSION BOARD PHOTO ......................... 4 1.2.1. Amazon 1: PCI-E Type ............................................................................. 4 1.2.2. Amazon 2: BTB Connector Type .............................................................. 5 1.2.3. Extension Board........................................................................................ 6 2. HW TEST SETUP..................................................................................... 6 2.1. CONNECT PC USB PORT TO EXTENSION BOARD USB CONNECTOR ......... 6 2.2. CONNECT PC USB PORT TO EXTENSION BOARD USIF 1 PORT ................ 8 3. SW TEST SETUP ................................................................................... 10 3.1 DRIVER INSTALLATION ......................................................................... 10 3.1.1. HS-USB Driver Installation...................................................................... 10 3.1.2. Prolific Driver Installation ........................................................................ 13 3.1.3. Connection Manager Installation ............................................................ 14 3.2 3.3 CONNECTION MANAGER ...................................................................... 15 CONNECTION WITH TEST INSTRUMENT.................................................. 16 APPENDIX 1: DETAIL DESCRIPTION OF EXTENSION BOARD .............. 19 APPENDIX 2: FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT ................................................................................................ 22 Notice Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 InnoComm may make changes to the user guide at any time; the information in this document is subject to change without notice. 1. INTRODUCTION This document describes operation and test setup of Amazon modem module. There are two types with Amazon modem module, one is PCI-E type (Amazon 1) and the other one is BTB connector type (Amazon 2). Extension board is used to connect Amazon modem module to PC side to do function test and debug. 1.1. Development Kit Content The development kit for Amazon modem module contains following items. 1. Modem Module: Amazon modem module x 1 2. Extension Board x 1 3. RF cable x 1 4. External Antenna x 1 5. SW driver disk x 1 Figure 1-1 Development Kit Content Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 1.2. Amazon modem module and Extension board photo 1.2.1. Amazon 1: PCI-E Type Figure 1-2 Amazon1 TOP Figure 1-3 Amazon1 BOTTOM Ver1.1 1.2.2. Amazon 2: BTB Connector Type Figure 1-4 Amazon2 TOP Figure 1-5 Amazon2 BOTTOM Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 1.2.3. Extension Board Figure 1-6 Extension Board 2. HW TEST SETUP 2.1. Connect PC USB Port to Extension Board USB Connector Application: Test with Instrument (CMU200, Agilent 8960…) or Real network test Requirement: SW: Driver, CM (Connection manager) installation HW: Test SIM for test with Instrument (CMU200, Agilent8960….etc) x1 Real SIM for test with Real network (Via external antenna) x1 Power supply x 1 Input voltage --- 3.3 V for Amazon 1 --- 3.7 V for Amazon 2 Instrument or external antenna x1 RF cable x 1 USB cable x1 Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 CMU200 RF cable DC POWER SUPPLY +3.7 +3.7 PC Power cable USB cable (to USB) USB PORT Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 2.2. Connect PC USB Port to Extension Board USIF 1 Port Application: Test with Instrument (CMU200, Agilent 8960…) Requirement: SW: Driver HW: Test SIM card x 1 Power supply x 1 Input voltage --- 3.3 V for Amazon 1 --- 3.7 V for Amazon 2 Instrument (CMU200, Agilent8960….etc) x1 RF cable x 1 USB cable x 1 Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 CMU200 RF cable DC POWER SUPPLY +3.7V +3.7V PC Power cable USB PORT USB cable (to USIF1) Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 3. SW TEST SETUP 3.1 Driver Installation 3.1.1. HS-USB Driver Installation The HS-USB driver should be installed when using USB Port. Following are the steps for installation. Step 1: Unzip and install the driver. File name: WMC_Comneon2_3.12.1 Driver\ Setup.exe. Then it will create one folder under C:\Program Files\Comneon\Highspeed Modem 0x20\Drivers\. Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-1 Setup.exe Figure 3-2 Driver folders Step 2: Connect UE device to PC with USB2.0 cable, and power on device Step 3: Install HS_USB Driver to PC. When device powered on and PC detect the device. The driver will install automatically or set direction to C:\Program Files\Comneon\Highspeed Modem 0x20\Drivers\ Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-3: Auto installations 6 virtual ports will be installed. (Comneon Mobile Highspeed Port), and One Modem Port. (Comneon Mobile Highspeed Modem MPE1) Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 Figure 3-4 Virtual Ports 3.1.2. Prolific Driver Installation The Prolific Driver should be installed when using USIF 1 or USIF 5 Port. Following are the steps for installation. Step 1: Unzip and install File name: PL2303_Prolific_DriverInstaller_v10518.exe. Step 2: Plug in USIF1 or USIF 5. PC will detect USB to Serial Ports and install the driver automatically. HS_USB USIF 1 Figure 3-5 USIF1 and USIF 5 Port USIF 5 Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-6 USB to Serial Ports 3.1.3. Connection Manager Installation Step1: Unzip ProjAmazonSetup.rar and install ProjP330Setup. Figure 3-7 Connection Manager Installation Step 2: Execute Connection Manager on desktop. A Network Connection, NET, will be created and modem should be “Comneon Mobile Highspeed Modem”. Figure 3-8 Connection Manager Icon Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-9 Network Connection 3.2 Connection Manager Connection Manager is used to perform network data link and SMS function. Following are basic descriptions of each icon in main menu. Home: Back to Main Menu SMS: - Create new message - List, read/edit Phone Book from SIM, Outlook list. - Inbox, read/reply/ delete from SMS storage. - Draft, save draft SMS in CM - Outbox, template storage when unable to sent SMS - Sent, see sent message in CM Data Link: Connection/ Disconnection Data call to network CM setting: -SMS, include storage, SMSC number setting, and SMS valid period -Profile, Operator APN setting (default is “internet”) -Network, Setting camping method, GSM/ UMTS selection, Fight mode switch, PIN lock. - Data, --Data usage, Limit total Data transfer --History, record Data connection history -Sys Info, Device IMEI, SW information -Debug, AT command line and history, HW control (power on/off, Radio on/off, Card reset). Device status Bar: Show device status. (Not detected, Camping, Data link success…) Figure 3-10 shows the main menu icons Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 Home SMS Data link CM Setting Device status Bar Figure 3-10 Main Menu Screen Note: 1. Please use “Exit” to quit CM. Tape the “x” on the window is to minimize CM into Windows application try, and it will not quit the CM. (See Figure 3-11) 2. Do not Open CM twice at same time. Modem com port will be hold when another CM is running. Figure 3-11 correct way to quit CM 3.3 Connection With Test Instrument Following steps show how to connect device to test instrument. Step 1: Plug in USIF 1 port. USIF 1 Figure 3-12 USIF 1 port Step 2: PC detects Prolific_USB -to- Serial Comm Port. (See Figure 3-13) Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-13 Prolific_USB -to- Serial Comm Port Step 3: Set up HyperTerminal as Figure 3-14. Figure 3-14 Hyper Terminal Settings Step 4: Send AT Command via HyperTerminal as Figure 3-15 Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-15 Send AT command Reference AT commands are as following: 1. Auto-search Network: AT+COPS=0 2. Make a circuit-switch call to instrument: ATD123456; (Do not miss the semicolon.) 3. In case, if SIM is locked by PIN number (e.g., 0000), use AT+CPIN=”0000” to unlock SIM PIN. Before unlock, the SIM PIN Lock will also cause ERROR when issuing AT+COPS=0. (Use AT+CPIN? to query the PIN status if you are not sure the SIM requires PIN or not.) Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Appendix 1: Detail description of Extension board 1. Placement CAUTION: DO NOT insert Amazon1 and Amazon2 Modules at the same time! Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 2. Connector J312 : USB port J202 : USIF1 Port to USB J203 : USIF5 port to USB J304 : PCI-E Slot J305 : SIM card connector J306 : BTB connector 3. Jumper J201 : USIF1 signal Pin1 : TXD (X-GOLD 616 output) Pin2 : RXD (X-GOLD 616 input) Pin3 : RTS (X-GOLD 616 output) Pin4 : CTS (X-GOLD 616 input) Pin5 : GND J204 : USIF5 signal Pin1 : TXD (X-GOLD 616 output) Pin2 : RXD (X-GOLD 616 input) Pin3 : RTS (X-GOLD 616 output) Pin4 : CTS (X-GOLD 616 input) Pin5 : GND J301 : External voltage input Pin1 : Input 3.3V for Amazon 1 and 3.7V for Amazon 2 Pin2 : Input 3.3V for Amazon 1 and 3.7V for Amazon 2 Pin3 : NC Pin4 : GND Pin5 : GND J302 : DC to DC convertor output Pin1 : Output Pin2 : Output Pin3 : NC Pin4 : GND Pin5 : GND J303 : Power select Pin1-2 short : power from USB (J312) Pin 2-3 short: power from jumper (J301)---Default J307 : SPI test pin Pin1 : SPI_SOMI Pin2 : SPI_SIMO Pin3 : SPI_CLK Pin4 : SPI_CS Pin5 : GND J308 : AGPS control test pin Pin1 : AGPS_BLANKIUNG Pin2 : AGPS_REFCLK Pin3 : AGPS_SYNC Pin4 : PIN16 Pin5 : GND Ver1.1 J309 : PCM test pin Pin1 : PCM_CLK Pin2 : PCM_UL Pin3 : PCM_DL Pin4 : PCM_SYNC Pin5 : GND J310 : Control test pin Pin1 : SRDY Pin2 : MRDY Pin3 : USB_ON Pin4 : SIM_OFF Pin5 : GND J311 : I2S test pin Pin1 : I2S2_CLK Pin2 : I2S2_RX Pin3 : I2S2_TX Pin4 : I2S2_SYNC Pin5 : GND J313 : GPIO test pin Pin1 : GPIO1 Pin2 : GPIO2 Pin3 : GPIO3 Pin4 : SIM_CD Pin5 : GND J314 : CLOCK test pin Pin1 : FSYS2_CLK Pin2 : FSYS2_EN Pin3 : FSYS3_CLK Pin4 : FSYS3_EN Pin5 : GND J315 : Control test pin Pin1 : RF_PA_ON Pin2 : RST_XMM6160 Pin3 : DBR_BLANKING Pin4 : PWR_FAIL Pin5 : GND J316 : Control test pin Pin1 : TX_PWR_TH Pin2 : CLKOUT2 Pin3 : NC Pin4 : FSYS4_CLK Pin5 : GND Amazon Modem Module Development Kit User Manual 7/26/2010 Appendix 2: Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. 4RF Exposure Information This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical Exclusion Requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons, must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. The end user has no manual instructions to remove or install the device and a separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. Maximum antenna gain allowed for use with this device is -0.95 dBi. When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: YAI-AZ1901”.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : user Title : Microsoft Word - Amazon Modem Module Development Kit User Manual_v1 2.doc Create Date : 2010:07:26 09:32:51+08:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2010:08:19 19:12:37+08:00 Metadata Date : 2010:08:19 19:12:37+08:00 Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:dc01c62d-a377-4abf-8d4b-fc9c7311d058 Instance ID : uuid:2e6c1a2c-82ce-4176-b7dd-99995bf970e2 Page Count : 22 Author : userEXIF Metadata provided by EXIF.tools