InnoComm Mobile Technology BM05-AN BT4.0 LE Module User Manual Module 20140909

Download:
Mirror Download [FCC.gov]
Document ID	2393492
Application ID	bmU16JAmuHVa8lG9ivXknA==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.7kB (146194 bits)
Date Submitted	2014-09-18 00:00:00
Date Available	2014-09-18 00:00:00
Creation Date	2014-09-17 13:17:15
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2014-09-17 13:17:15
Document Title	Microsoft Word - Module User Manual_20140909.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	097019

InnoComm Mobile Technology Corporation
3F, No. 6, Hsin Ann Rd., Hsinchu Science Park, Hsinchu 30078, Taiwan
TEL: +886-3-5781868 FAX: +886-3-5781187
BT4.0 Low Energy Module
User Manual
FCC ID: YAIBM05-AN
Introduction
This document describes pin definition, mechanical drawing and reflow data of
Bluetooth Low Energy Module and hope it can helps designer to design in easier
and manufacturing smoothly.
Pin Definition
Pin #
Pin Name
Direction
Voltage
Desription
VDD
1.8 to 3.3V
Input power can range from 1.8V to 3.3V
VSS
GND
TEST0
I/O
1.8V to 3.3V Mfg Test pin 0; MODE "POINTER". Internally
pulled-up (active low)
TEST1
I/O
1.8V to 3.3V Mfg Test pin 1; MODE "JOYSTICK". Internally
pulled-up (active low)
SDA
I/O
1.8V to 3.3V I2C data to interface with sensors (gyro &
accelerometer) for relative
motion. May also interface to additional I2C memory.
SCL
1.8V to 3.3V I2C clock to interface with sensors (gyro &
accelerometer) for relative
motion. May also interface to additional I2C memory.
TEST2
I/O
1.8V to 3.3V Mfg Test pin 2
GPIO_2
I/O
1.8V to 3.3V Interrupt from I2C accelerometer. Internally pulled‐up.
GPIO_3
I/O
1.8V to 3.3V Interrupt from I2C gyro. Internally pulled‐up.
10
GPIO_0
I/O
1.8V to 3.3V "A" button. Internally pulled‐up.
11
GPIO_1
I/O
1.8V to 3.3V "B" button. Internally pulled‐up.
12
GPIO_4
I/O
1.8V to 3.3V General I/O - UNUSED. Internally pulled-up.
13
GPIO_5
I/O
1.8V to 3.3V "HOME" button. Internally pulled‐up.
14
GPIO_6
I/O
1.8V to 3.3V "HELP" button. Internally pulled‐up.
15
GPIO_7
I/O
1.8V to 3.3V "PAUSE" button. Internally pulled‐up.
16
GPIO_10
I/O
1.8V to 3.3V LED for player "1".
17
GPIO_11
I/O
1.8V to 3.3V LED for player "2".
18
ADC_0
1.8V to 3.3V ADC input for X direction on joystick.
19
ADC_1
1.8V to 3.3V ADC input for Y direction on joystick.
20
ADC_2
1.8V to 3.3V ADC input for battery voltage.
21
GPIO_8
I/O
1.8V to 3.3V Power LED.
22
GPIO_9
I/O
1.8V to 3.3V IR LED.
23
GPIO_12
I/O
1.8V to 3.3V General I/O ‐ UNUSED. Internally pulled‐up.
Ground
Mechanical Drawing
Reflow data
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
‐
‐
‐
‐
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be
kept as far as possible from the user body or set the device to lower output power
if such function is available.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co‐located with any other transmitter or
antenna.
As long as 1 condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end‐product for
any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co‐location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re‐evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.
End Product Labeling
The product can be kept as far as possible from the user body or set the device to
lower output power if such function is available. The final end product must be
labeled in a visible area with the following: “Contains FCC ID: YAIBM05‐AN”. The
grantee's FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Title                           : Microsoft Word - Module User Manual_20140909.doc
Creator                         : 097019
Create Date                     : 2014:09:17 13:17:15+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2014:09:17 13:17:15+08:00
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Document ID                     : uuid:256fb6ee-b269-40ec-ba20-a184a4267867
Instance ID                     : uuid:4a26afcb-8d87-4fd5-be5f-9ed7cc626ef5
Page Count                      : 5
Author                          : 097019

EXIF Metadata provided by EXIF.tools