InnoComm Mobile Technology BM10-AN BT4.0 LE Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2649174
Application ID	bFAuCH0K/7+lmd/ldxpxIA==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	70.63kB (882861 bits)
Date Submitted	2015-06-16 00:00:00
Date Available	2015-06-16 00:00:00
Creation Date	2015-06-10 10:45:27
Producing Software	doPDF Ver 7.3 Build 391 (Windows 7 Enterprise Edition - Version: 6.1.7600 (x86))
Document Lastmod	2015-06-10 14:34:27
Document Title	User Manual.pdf

BT4.0 LE Module
User Manual
Model name: BM10_AN
Introduction
This document describes Key feature, pin definition, mechanical drawing,
Recommendation for PCB Layout and operation temperature and voltage range, and
reflow data of Bluetooth Low Energy Module and it can helps designer to design in
easier and manufacturing smoothly.
BLE module Install Guide line
Key Features
RF
• 2.4-GHz Bluetooth low energy Compliant and Proprietary RF Single Mode Module
• Supports 250-kbps, 500-kbps, 1-Mbps, 2-Mbps Data Rates
• Software programmable adjustable transmitter power (-20dBm to 5dBm) for short
to long range applications
• Suitable for Systems Targeting Compliance With Worldwide Radio Frequency
Regulations: ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47
Part 15 (US), and ARIB STD-T66 (Japan)
Layout
• Few External Components
• 25.45 mm × 16.7 mm × 2 mm, 40 pin LCC Package
Low Power
• Wide supply voltage range : 1.8 – 3.8V
• Differential RF mode : 6.4±3 mA
• Differential RF mode TX at 0 dBm: 6.8±3 mA
• Differential RF mode TX at +5 dBm: 8.9±3mA
• Low Power Mode: 1 μA (RTC Running + RAM/CPU retention)
• Low Power Mode: 100 nA (Flash retention)
• Optional on-chip DC/DC converter (not available in 1.8V mode)
Peripherals
• Integrated temperature sensor
• 4 General-purpose Timer Modules (8x 16-bit or 4x 32 bit-timer, PWM each)
• 12-bit ADC, 200 ksamples/s, 8 channel analog MUX
• Ultra-low-power analog comparator
• UART
• 2x SPI
• Ultra-low power
• I2C, I2S
• Real-time clock
• AES-128 security module
• Support for 8 capacitive sensing channels
Application Profile
• Consumer electronics
• Mobile phone accessories
• Sports & Fitness equipment
• HID applications
• Home and Building Automation
• Lighting Control
• Alarm and Security
• Electronic Shelf Labeling
• Proximity Tags
• Medical
• Remote Controls
• Wireless Sensor Networks
Mechanical Drawing
Module Pin Definition
Bluetooth Module
Pin #
Pin Name
GND
Direction
Voltage
Description
Power
GND
Ground
DIO_0
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface
DIO_1
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface
DIO_2
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface
DIO_3
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface
DIO_4
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface
DIO_5
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, LED driving capability
DIO_6
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, LED driving capability
DIO_7
Digital I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, LED driving capability
10
VDDS2
Power
1.8V to 3.8V
1.8V – 3.8V DIO supply
11
DIO_8
Digital I/O
1.8V to 3.8V
GPIO
12
DIO_9
Digital I/O
1.8V to 3.8V
GPIO
13
DIO_10
Digital I/O
1.8V to 3.8V
GPIO, LED driving capability
14
DIO_11
Digital I/O
1.8V to 3.8V
GPIO, LED driving capability
15
DIO_12
Digital I/O
1.8V to 3.8V
GPIO
16
DIO_13
Digital I/O
1.8V to 3.8V
GPIO
17
DIO_14
Digital I/O
1.8V to 3.8V
GPIO
18
DIO_15
Digital I/O
1.8V to 3.8V
GPIO
19
VDDS3
Power
1.8V to 3.8V
1.8V – 3.8V DIO supply
20
JTAG_TMSC
Digital I/O
1.8V to 3.8V
JTAG_TMSC
21
JTAG_TCKC
Digital I/O
1.8V to 3.8V
JTAG_TCKC
22
JTAG_TDO
Digital I/O
1.8V to 3.8V
GPIO, JTAG_TDO
23
JTAG_TDI
Digital I/O
1.8V to 3.8V
GPIO, JTAG_TDI
24
GND
Power
GND
Ground
25
DIO_18
Digital I/O
1.8V to 3.8V
GPIO
26
DIO_19
Digital I/O
1.8V to 3.8V
GPIO
27
DIO_20
Digital I/O
1.8V to 3.8V
GPIO
28
DIO_21
Digital I/O
1.8V to 3.8V
GPIO
29
DIO_22
Digital I/O
1.8V to 3.8V
GPIO
30
VDD
Power
1.8V to 3.8V
1.8V – 3.8V main chip supply
31
nRESET
1.8V to 3.8V
Reset, active-low. No internal pull-up
32
DIO_23
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
33
DIO_24
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
34
DIO_25
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
35
DIO_26
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
36
DIO_27
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
37
DIO_28
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
38
DIO_29
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
39
DIO_30
Digital/Analog I/O
1.8V to 3.8V
GPIO, ULP Sensor Interface, Analog
40
GND
Power
GND
Ground
Reference Circuit for User design
Recommended: Operating Range
over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX
Operating ambient temperature range, TA
Operating supply voltage
–40
1.8
Recommendation: PCB Layout for User design
UNIT
85
°C
3.8
Reflow data
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 1 condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The product can be kept as far as possible from the user body or set the device
to lower output power if such function is available. The final end product must
be labeled in a visible area with the following: “Contains FCC ID: YAIBM10-AN ”.
The grantee's FCC ID can be used only when all FCC compliance requirements
are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2015:06:10 10:45:27+08:00
Modify Date                     : 2015:06:10 14:34:27+08:00
Metadata Date                   : 2015:06:10 14:34:27+08:00
Producer                        : doPDF Ver 7.3 Build 391 (Windows 7 Enterprise Edition - Version: 6.1.7600 (x86))
Format                          : application/pdf
Document ID                     : uuid:ff711a6c-9924-4abf-8006-1e632002fca7
Instance ID                     : uuid:c7529317-fc1a-4291-b921-8d4b7c439898
Page Count                      : 10
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools