InnoComm Mobile Technology BM15R2 BLE Single Mode Module User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3616282
Application ID	urcENNpdErWHLG6GtZo0mg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	238.35kB (2979415 bits)
Date Submitted	2017-10-24 00:00:00
Date Available	2017-10-26 00:00:00
Creation Date	2017-10-17 12:37:04
Producing Software	doPDF Ver 7.3 Build 391 (Windows 7 Enterprise Edition (SP 1) - Version: 6.1.7601 (x86))
Document Lastmod	0000-00-00 00:00:00
Document Title	Manual

BM15_AN R2 BLE Single Mode Module
Product Specification
Model Name
Project code
Description
Revision
Issue Date
Approved by
Harrison Chen
BM15_AN R2
BLE Single Mode Module
1.4
2017/09/26
Reviewed by
Taka Wei
Issued by
Aaron Lai
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
Revision History
Revision Released Date
Comments/Remark
Author
1.0
2017/03/07
Initial release
Aaron Lai
1.1
2017/03/29
Update reflow profile
Aaron Lai
1.2
2017/06/07
Update module photo and correct content Aaron Lai
typo
1.3
2017/07/10
Update GPIO pin 31 description and
Reference Circuit
Aaron Lai
1.4
2017/09/26
Update ME drawing, layout and placement
section
Aaron Lai
® 2017 InnoComm Mobile Technology Corp.
Disclaimer
BM15_AN R2 BLE MODULE are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty for a particular purpose. No license is granted by
implication or otherwise under any patents or other intellectual property by application or use of evaluation
boards. Information furnished by InnoComm is believed to be accurate and reliable. InnoComm reserves the
right to change specifications or product description in this document at any time without notice.
Should Buyer purchase or use InnoComm’s products for any such unintended or unauthorized application,
Buyer shall indemnify and hold InnoComm harmless against all claims and damages.
InnoComm is the trademarks of InnoComm Mobile Technology Corp.
Other trademarks and registered trademarks mentioned herein are the property of their respective owners.
2/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
TABLE OF CONTENT
1. INTRODUCTION ......................................................................................... 4
2. GENERAL INFORMATION ........................................................................ 5
2.1 KEY FEATURES .................................................................................................... 5
2.2 BLOCK DIAGRAM ................................................................................................. 7
3. PIN MAP AND SIGNAL DESCRIPTION .................................................... 8
3.1 REFERENCE CIRCUIT .......................................................................................... 9
4. ELECTRICAL CHARACTERISTICS ........................................................10
4.1 RECOMMENDED OPERATING RANGE ............................................................. 10
4.2 POWER CONSUMPTION .................................................................................... 10
5. RF CHARACTERISTICS ..........................................................................11
6. MECHANICAL INFORMATION ......................................................... …..12
7. PCB LAYOUT RECOMMENDATION ......................................................13
8. MODULE PLACEMENT LAYOUT GUIDE...............................................14
9. SMT SOLDER REFLOW RECOMMENDATION .....................................15
10. PRODUCT AND DOCUMENTATION SUPPORT...................................16
10.1 DEVELOPMENT SUPPORT .............................................................................. 16
10.2 DOCUMENTATION SUPPORT.......................................................................... 17
10.3 COMMUNITY RESOURCES .............................................................................. 17
Federal Communication Commission Interference Statement ................... 18
3/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
1. INTRODUCTION
Based on TI’s outstanding CC2640R2 BLE technology, Innocomm’s BM15_AN R2 module is a wireless
microcontroller (MCU) targeting Bluetooth® 4.2 and Bluetooth 5 low-energy applications.
It is with very low active RF and MCU current and low-power mode current consumption provide excellent
battery lifetime and allow for operation on small coin cell batteries and in energy-harvesting applications and
embedded PCB antenna.
BM15_AN R2 module contains a powerful 32-bit Cortex M3 running up to 48 MHz as the main processor and
a rich peripheral feature set that includes a unique ultra-low power sensor controller.
Bluetooth low energy controller and host libraries are embedded in ROM and run partly on an
ARM® Cortex®-M0 processor. This architecture improves overall system performance and power
consumption and frees up significant amounts of flash memory for the application.
4/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
2. General Information
2.1 Key Features
RF
•
•
•
•
•
2.4-GHz RF Transceiver Compatible With Bluetooth low energy (BLE) 4.2 and 5 Specifications
Supports data rates between 1 Mbps
Programmable output power up to +5 dBm
Excellent Receiver Sensitivity (–97 dBm for BLE), Selectivity, and Blocking Performance
Suitable for Systems Targeting Compliance With Worldwide Radio Frequency Regulations
– ETSI EN 300 328 (Europe)
– EN 300 440 class 2 (Europe)
– FCC CFR47 Part 15 (US)
– ARIB STD-T66 (Japan)
Layout
•
•
Few External Components
18.0 mm × 10.5 mm × 2.0 mm, 26 pin LCC Package
Low Power
•
•
•
•
•
•
Wide supply voltage range : 1.9 – 3.8V
Differential RF mode : 6.4±3 mA
Differential RF mode TX at 0 dBm: 6.8±0.3 mA
Differential RF mode TX at +5 dBm: 8.9±0.3mA
Low Power Mode: 1 μA (RTC Running + RAM/CPU retention)
Low Power Mode: 100 nA (Flash retention)
Peripherals
•
•
•
•
•
•
•
•
•
•
•
•
Integrated Temperature Sensor
Four General-Purpose Timer Modules (Eight 16-Bit or Four 32-Bit Timers, PWM Each)
12-bit ADC, 200-ksamples/s, 8-Channel Analog MUX
Ultra-Low-Power Analog Comparator
UART
2x SSI (SPI, MICROWIRE, TI)
Ultra-low power
I2C, I2S
Real-time clock
AES-128 security module
15 GPIOs
Support for 8 capacitive sensing channels
Application
•
Home and Building Automation
– Connected Appliances
– Lighting
– Locks
– Gateways
– Security Systems
•
Industrial
– Logistics
– Production and Manufacturing Automation
– Asset Tracking and Management
5/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
– HMI and Remote Display
– Access Control
•
Retail
– Beacons
– Advertising
– ESL and Price Tags
– Point of Sales and Payment Systems
•
Health and Medical
– Thermometers
– SpO2
– Blood Glucose and Pressure Meters
– Weight Scales
– Hearing Aids
•
Sports and Fitness
– Activity Monitors and Fitness Trackers
– Heart Rate Monitors
– Running and Biking Sensors
– Sports Watches
– Gym Equipment
– Team Sports Equipment
•
HID
– Voice Remote Controls
– Gaming
– Keyboards and Mice
6/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
2.2 Block Diagram
7/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
3. PIN Map and Signal Description
Pin #
Pin Name
Direction/Type
Description
GND
Power
Ground
DIO_0
Digital I/O
GPIO, Sensor Controller
DIO_1
Digital I/O
GPIO, Sensor Controller
DIO_2
Digital I/O
GPIO, Sensor Controller, high-drive capability
DIO_3
Digital I/O
GPIO, Sensor Controller, high-drive capability
DIO_4
Digital I/O
GPIO, Sensor Controller, high-drive capability
JTAG_TMSC
Digital I/O
JTAG TMSC, high-drive capability
JTAG_TCKC
Digital I/O
JTAG_TCKC
JTAG_TDO
Digital I/O
GPIO, High drive capability, JTAG_TDO
10
JTAG_TDI
Digital I/O
GPIO, High drive capability, JTAG_TDI
11
GND
Power
Ground
12
GND
Power
Ground
13
nRESET
Digital input
Reset, active-low, with internal pull-up
14
DIO_7
Digital/Analog I/O
GPIO, Sensor Controller, Analog
15
DIO_8
Digital/Analog I/O
GPIO, Sensor Controller, Analog
16
DIO_9
Digital/Analog I/O
GPIO, Sensor Controller, Analog
17
DIO_10
Digital/Analog I/O
GPIO, Sensor Controller, Analog
18
DIO_11
Digital/Analog I/O
GPIO, Sensor Controller, Analog
19
DIO_12
Digital/Analog I/O
GPIO, Sensor Controller, Analog
20
DIO_13
Digital/Analog I/O
GPIO, Sensor Controller, Analog
21
DIO_14
Digital/Analog I/O
GPIO, Sensor Controller, Analog
22
VDD
Power
1.9V to 3.8V main chip supply
23
GND
Power
Ground
24
GND
Power
Ground
25
GND
Power
Ground
26
GND
Power
Ground
8/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
3.1 Reference Circuit
9/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
4. ELECTRICAL CHARACTERISTICS
4.1 Recommended Operating Range
PARAMETER
CONDITIONS
MIN
Operating ambient temperature range, TA
Operating supply voltage
For operation in battery-powered and 3.3V systems
MAX
UNIT
–40
NOM
85
°C
1.9
3.8
4.2 Power Consumption
Unless noted, all specifications are at 25 °C and Vbat = 3.0 V.
PARAMETER
Low Power Mode (LPM4.5)
TEST CONDITIONS
Shutdown. No clocks running, no retention
MIN
TYP
100
MAX
Low Power Mode (LPM3)
With RTC, CPU, RAM and (partial) register retention
Power consumption radio RX(2)
With DC/DC
6.1
6.4
6.7
mA
Power consumption radio TX(2)
With DC/DC, 0 dBm output power
6.5
6.8
7.1
mA
Power consumption radio TX(2)
With DC/DC, 5 dBm output power
8.6
8.9
9.2
mA
10/19
InnoComm Mobile Technology Confidential
UNIT
nA
uA
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
5. RF Characteristics
1 Mbps GFSK (Bluetooth low energy)
Unless noted, all specifications are at 25 °C, Vbat = 3.0 V and fRF = 2440MHz.
PARAMETER
RX Receiver sensitivity
TEST CONDITIONS
Differential mode, measured in 50Ω single-ended, BER=10-3
TX Output power, highest setting
Differential mode, delivered to a single ended 50 Ω load
+5
dBm
TX Output power, lowest setting
Delivered to a single ended 50Ω load
-20
dBm
Spurious emission 30-1000 MHz
Conducted measurement in a 50Ω single ended load.
Complies with EN 300 328, EN 300 440 class 2, FCC CFR47,
Part 15 and ARIB STD-T-66
Spurious emission 1-12.75 GHz
MIN
TYP
-97
MAX
UNIT
dBm
-57
dBm
-47
dBm
Note: BM15_AN R2 module is with “Internal bias” mode design and related SW setting need to match with
“Internal bias” mode.
11/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
6. Mechanical Information
12/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
7. PCB Layout Recommendation
13/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
8. Module Placement Layout Guide
Placement Note: Please refer to “BM15_AN Module_Placement guideline v1.0.pdf”.
Layout Note: Do not route any trace under module to avoid interference.
(O)
(X)
14/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
9. SMT Solder Reflow Recommendation
Note: Allowable reflow soldering times: 2 times base on recommended reflow
profile.
15/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
10. Product and Documentation Support
10.1. Development Support
TI offers an extensive line of development tools, including tools to evaluate the performance of the
processors, generate code, develop algorithm implementations, and fully integrated and debug
software and hardware modules.
The following products support development of the CC2640 R2 device applications:
Software Tools:
SmartRF™ Studio 7 is a PC application that helps designers of radio systems to easily evaluate the
RF-IC at an early stage in the design process.
• Test functions for sending and receiving radio packets, continuous wave transmit and receive
• Evaluate RF performance on custom boards by wiring it to a supported evaluation board or
debugger
• Can also be used without any hardware, but then only to generate, edit and export radio
configuration settings
• Can be used in combination with several development kits for Texas Instruments’ CCxxxx RF-ICs
Sensor Controller Studio provides a development environment for the CC26xx Sensor Controller.
The Sensor Controller is a proprietary, power-optimized CPU in the CC26xx, which can perform
simple background tasks autonomously and independent of the System CPU state.
• Allows for Sensor Controller task algorithms to be implemented using a C-like programming
language
• Outputs a Sensor Controller Interface driver, which incorporates the generated Sensor Controller
machine code and associated definitions
• Allows for rapid development by using the integrated Sensor Controller task testing and debugging
functionality. This allows for live visualization of sensor data and algorithm verification.
IDEs and Compilers:
Code Composer Studio:
• Integrated development environment with project management tools and editor
• Code Composer Studio (CCS) 7.0 and later has built-in support for the CC26xx device family
• Best support for XDS debuggers; XDS100v3, XDS110 and XDS200
• High integration with TI-RTOS with support for TI-RTOS Object View
IAR Embedded Workbench for ARM
• Integrated development environment with project management tools and editor
• IAR EWARM 7.80.1 and later has built-in support for the CC26xx device family
• Broad debugger support, supporting XDS100v3, XDS200, IAR I-Jet and Segger J-Link
• Integrated development environment with project management tools and editor
• RTOS plug in available for TI-RTOS
For a complete listing of development-support tools for the CC2640 R2 platform, visit the Texas
Instruments website at www.ti.com. For information on pricing and availability, contact InnoComm
Mobile Technology Corporation sales office or authorized distributor.
16/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
10.2. Documentation Support
To receive notification of documentation updates, navigate to the device product folder on ti.com
(CC2640R2F). In the upper right corner, click on Alert me to register and receive a weekly digest of any
product information that has changed. For change details, review the revision history included in any revised
document.
The current documentation that describes the CC2640R2F devices, related peripherals, and other technical
collateral is listed in the following.
Technical Reference Manual
SWCU117 Technical Reference Manual. Texas Instruments CC26xx Family of Products
10.3. Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the
respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see
TI's Terms of Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster
collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and
help solve problems with fellow engineers.
TI Embedded Processors Wiki Texas Instruments Embedded Processors Wiki. Established to help
developers get started with Embedded Processors from Texas Instruments and to foster innovation and
growth of general knowledge about the hardware and software surrounding these devices.
17/19
InnoComm Mobile Technology Confidential
REV 1.4
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
18/19
InnoComm Mobile Technology Confidential
iCOM_BM15_AN R2 Module Product Specification
9/26/2017
REV 1.4
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as possible from the
user body or set the device to lower output power if such function is available.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The product can be kept as far as possible from the user body or set the device to lower
output power if such function is available. The final end product must be labeled in a visible
area with the following: “Contains FCC ID: YAIBM15R2”. The grantee's FCC ID can be
used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
19/19
InnoComm Mobile Technology Confidential

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 19
Page Layout                     : OneColumn
Page Mode                       : UseNone
Producer                        : doPDF Ver 7.3 Build 391 (Windows 7 Enterprise Edition (SP 1) - Version: 6.1.7601 (x86))
Create Date                     : 2017:10:17 12:37:04+08:00

EXIF Metadata provided by EXIF.tools