InnoComm Mobile Technology CM05 Wireless Module User Manual
InnoComm Mobile Technology Corporation Wireless Module
User Manual
CM05 WIFI/BLE Module Product Specification Model Name CM05 Project code Description WIFI/BLE Version 1.2 Issue Date 2018/05/31 Approved by Taka Wei Reviewed by JH Huang Issued by Iestyn Chen CM05 Product Specification 2018/10/31 REV1.2 Revision History Revision Released Date Comments/Remark Author 0.1 2017/10/13 Initial release Iestyn Chen 0.2 2017/12/01 Add in HW performance data Iestyn Chen 0.3 2017/12/12 Modify the memory configuration of WiFi Iestyn Chen 1.0 2018/03/09 Modify the spec JH 1.1 2018/04/12 Modify the Mechanical information JH 1.2 2018/05/31 Modify the current consumption spec JH ® 2018 InnoComm Mobile Technology Corp. GENERAL NOTICE THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PRODUCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH THE PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CONTAINS INFORMATION ABOUT INNOCOMM PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT INNOCOMM'S DISCRETION. INNOCOMM MOBILE TECHNOLOGY GRANTS A NON-EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY, TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS; DISASSEMBLE OR DECOMPILE THE PRODUCT OR OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE RECIPIENT UNDERTAKES FOR AN UNLIMITED PERIOD OF TIME TO OBSERVE CONFIDENTIALLITY REGARDING ANY INFORMATION AND DATA PROVIDED TO THEM IN THE CONTEXT OF THE DELIVERY OF THE PRODUCT. THIS GENERAL NOTE SHALL BE GOVERNED AND CONSTRUED ACCORDING TO TAIWAN LAW. Copyright Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved. Copyright © 2018, InnoComm Mobile Technology Corp. Trademark Notice InnoComm® is the trademarks of InnoComm Mobile Technology Corp. Other trademarks and registered trademarks mentioned herein are the property of their respective owners. 2/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 TABLE OF CONTENT 1. INTRODUCTION ......................................................................................... 4 2. KEY FEATURES......................................................................................... 4 3. PIN MAP AND SIGNAL DESCRIPTION .................................................. 6 4. REFERENCE CIRCUIT............................................................................... 7 5. ELECTRICAL CHARACETRISTICS ....................................................... 8 6. RF CHARACTERISTICS ............................................................................ 9 7. MECHANICAL INFORMATION ..............................................................11 8..RECOMMENDED PCB LAYOUT FOOTPRINT ......................................11 9. MODULE LAYOUT GUIDE ..................................................................12 10. SMT SOLDER REFLOW RECOMMENDATION ..................................14 11. APPENDIX ............................................................................................. 15 3/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 1. Introduction CM05 is a compact module that integrates both BLE and WiFi function, and an ARM Cortex-M4 MCU that runs customer’s application. The typical application of the module is bridging BLE sensor clients to the cloud through WiFi router. 2. Key Features ■ BLE • • • • • • • • • BLE 5 connectivity ARM Cortex-M4 32-bit processer with FPU Memory – 512kB Flash (chip internal) – 64kB RAM (chip internal) 2.4GHz transceiver – 95dBm sensitivity in Bluetooth low energy mode 1Mbps, 2Mbps supported data rate TX power -20 to +4 dBm in 4 dB steps Single-pin antenna interface ■ WIFI ARM Cortex-M4 32-bit processer with FPU • Memory • – 512kB ROM (chip internal) – 256kB RAM (chip internal) – 2MB Flash (external) Radio – Single-pin antenna interface – 2.4GHz Support of Standard – 802.11b/g/n compatible WLAN – 802.11e QoS Enhancement(WMM) – 802.11i(WPA, WPA2). Open, shared key, and pair-wise key authentication services – WIFI Direct support – Light Weight TCP/IP protoco 4/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 3. PIN Map and Signal Description Refer to Section 9 for pin location and arrangement. Pin # Pin Name Description GND GND Ground Ground BLE_ANT BLE Antenna GND Ground GPIO15 Digital GPIO14 Digital SWDIO BLE Debug/download SWCLK BLE Debug/download VDD Module Power in 10 n_RESET Reset, active Low, with internal pull–up 11 GPIO13 Digital/Trace port CLK 12 GPIO12 Digital 13 WIFI_DEBUG_EN WiFi Debug mode Enable 14 GND Ground 15 SWD_DATA WiFi Debug 16 SWD_CLK WiFi Debug 17 GND Ground 18 WIFI_ANT WiFi Antenna 19 GND Ground 20 WIFI_DEBUG_RX WiFi Log UART/download 21 WIFI_DEBUG_TX WiFi Log UART/download 22 GND Ground 23 GPIO10 Digital/Trace port 24 GPIO9 Digital/Trace port 25 GPIO8 Digital 26 GPIO7 Digital 27 GPIO6 Digital 28 GPIO5 Digital 29 GPIO11 Digital 30 GPIO4 Analog/Digital, SAADC/COMP/LPCOMP input 31 GPIO3 Analog/Digital, SAADC/COMP/LPCOMP input 32 GND Ground 33 GND Ground 34 GPIO1 Analog/Digital, SAADC/COMP/LPCOMP input 35 GPIO2 Analog/Digital, SAADC/COMP/LPCOMP input 36 GPIO22 Analog/Digital, SAADC/COMP/LPCOMP input 37 GPIO21 Analog/Digital, SAADC/COMP/LPCOMP input 5/16 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 Pin # Pin Name Description 38 GPIO20 Analog/Digital, SAADC/COMP/LPCOMP input 39 GPIO19 Analog/Digital, SAADC/COMP/LPCOMP input 40 GPIO18 Digital 41 GPIO17 Digital 42 GPIO16 Digital 43 GND Ground F1 NC F2 NC F3 NC F4 NC F5 NC F6 NC 6/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 4. ELECTRICAL CHARACETRISTICS 4.1 Recommended Operating Range PARAMETER Operating temperature range Operating supply voltage MIN –20 TYP 25 3.3 MAX 85 3.6 UNIT °C MIN TYP MAX UNIT 280 mA 280 mA 350 mA 130 mA 25 mA 16 10 mA uA 4.2 Power Consumption PARAMETER WIFI 11n TX supply current at maximum output power WIFI 11g TX supply current at maximum output power WIFI 11b TX supply current at maximum output power WIFI RX supply current BLE TX supply current at maximum output power(+4dBm) BLE RX System off mode Detail to be added 4.3 GPIO Characterization information PARAMETER Voltage at digital I/O pins Input Low voltage level(VIL) Input High voltage level(VIH) Output Low Voltage level(VOL) Output Low Voltage level(VOH) MIN -0.3 TYP 0.7xVDD VDD-0.4 7/15 InnoComm Mobile Technology MAX UNIT VDD + 0.3 0.3xVDD VDD 0.4 VDD CM05 Product Specification 2018/10/31 REV1.2 5. RF Characteristics 5.1 BLE TX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) Tamb = -20 °C to 85 °C, VCC = 3.3 V Bursts: 10, Payload: PRBS 9, Length: 37 Bytes PARAMETER Maximum TX Power MIN TYP 1st Adjacent Channel Transmit Power 1 MHz (1 Msps) 2nd Adjacent Channel Transmit Power 2 MHz (1 Msps) 1st Adjacent Channel Transmit Power 2 MHz (2 Msps) 2nd Adjacent Channel Transmit Power 4 MHz (2 Msps) MAX UNIT dBm -25 dBc -50 dBc -25 dBc -50 dBc 5.2 BLE RX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) Tamb = -20 °C to 85 °C, VCC = 3.3 V, Payload: PRBS 9, Length: 37 PARAMETER Receiver Sensitivity MIN -95 TYP MAX UNIT dBm 5.3 WIFI TX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified Tamb = -20 °C to 85 °C, VCC = 3.3 V PARAMETER Maximum TX Power 802.11G 54MHz Maximum TX Power 802.11B 11MHz Maximum TX Power 802.11N HT20 Maximum TX Power 802.11N HT40 MIN TYP MAX 20.5 28 28 26 8/15 InnoComm Mobile Technology UNIT dBm dBm dBm dBm CM05 Product Specification 2018/10/31 REV1.2 Following characteristics are valid for conditions as follows (unless otherwise specified Tamb = -20 °C to 85 °C, VCC = 3.3 V PARAMETER EVM 802.11G 54MHz EVM 802.11B 11MHz EVM 802.11N HT20 EVM 802.11N HT40 MIN TYP MAX -30 -24.5 -31 -31 UNIT dB dB dB dB 5.4 WIFI RX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified Tamb = -20 °C to 85 °C, VCC = 3.3 V PARAMETER MIN TYP MAX Sensitivity 802.11G 54MHz -79 Sensitivity 802.11B 11MHz -89 Sensitivity 802.11N HT20 -73 Sensitivity 802.11N HT40 -70 9/15 InnoComm Mobile Technology UNIT dBm dBm dBm dBm CM05 Product Specification 2018/10/31 REV1.2 6. Mechanical Information 7. Recommended PCB Layout Footprint 10/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 8. Module Layout Guide I. Do not route traces under module to minimize on interference. (O) (X) 11/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 II. The trace Impedance of the antenna port (Pin 18) is 50 Ω. In order to minimize the return loss, it is recommended to use short traces. III. Keep enough clearance between the antenna port (Pin 18) and surrounding GND to minimize the power loss. (O) 12/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 (X) 9. SMT Solder Reflow Recommendation Note: Allowable reflow soldering times: 2 times base on recommended reflow profile. 13/15 InnoComm Mobile Technology CM05 Product Specification 2018/10/31 REV1.2 10. Appendix IO Mapping BLE Pin Number Pin Name P0.02 P0.03 P0.04 P0.05 P0.06 P0.07 10 P0.08 11 P0.09 12 P0.10 Type Analog/Digital Analog/Digital Analog/Digital Analog/Digital Digital Digital Digital NFC/Digital NFC/Digital 14 P0.11 Digital 15 P0.12 Digital 16 P0.13 Digital 17 18 19 P0.14 P0.15 P0.16 Digital/Trace port Digital/Trace port Digital/Trace port 20 P0.17 Digital 21 22 23 24 27 28 29 37 38 39 40 41 42 43 P0.18 P0.19 P0.20 P0.21 P0.22 P0.23 P0.24 P0.25 P0.26 P0.27 P0.28 P0.29 P0.30 P0.31 Digital/Trace port Digital Digital/Trace port CLK Digital/Reset Digital Digital Digital Digital Digital Digital Analog/Digital Analog/Digital Analog/Digital Analog/Digital CM05 Module Pin Assignment Pin Number Pin name 34 GPIO1 35 GPIO2 31 GPIO3 30 GPIO4 29 GPIO11 28 GPIO5 27 GPIO6 26 GPIO7 25 GPIO8 WIFI Pin name GPIOA23 UART0_TXD GPIOA22 UART0_RTS GPIOA19 UART0_CTS 24 23 GPIO9 GPIO10 WIFI_EN GPIOA18 UART0_RXD GPIOA_5 12 11 10 GPIO12 GPIO13 nReset GPIOA_12 42 41 40 39 38 37 36 14/15 InnoComm Mobile Technology GPIO14 GPIO15 GPIO16 GPIO17 GPIO18 GPIO19 GPIO20 GPIO21 GPIO22 CM05 Product Specification 2018/10/31 REV1.2 Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Label Instructions: The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID:YAICM05”,or “Contains FCC ID: YAICM05”, Any similar wording that expresses the same meaning may be used. 15/15 InnoComm Mobile Technology
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : 099011 Company : Created : D:20181031 Create Date : 2018:11:01 09:21:13+08:00 Last Saved : D:20181101 Modify Date : 2018:11:01 11:26:20-07:00 Source Modified : D:20181101012047 Has XFA : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2018:11:01 11:26:20-07:00 Creator Tool : Acrobat PDFMaker 11 Word 版 Document ID : uuid:66e374df-f6b3-421b-9cae-8f78ecbd0292 Instance ID : uuid:c93a3540-ae31-4a14-b7d7-32f548197cfa Subject : 4 Format : application/pdf Creator : 099011 Producer : Adobe PDF Library 11.0 Page Layout : OneColumn Page Count : 15EXIF Metadata provided by EXIF.tools