InnoSenT IPM165US K-Band Transceiver User Manual IPM 165 US

InnoSenT GmbH K-Band Transceiver IPM 165 US

User Manual

Version 1.0 IPM-165_US page 1 of 3 2007-02-22 User Manual Product Family: K-Band Transceivers K-Band Transceiver with two integrated patch antennas IPM-165_US Description: - radar-based motion detector centered @ 24.125 GHz - advanced PHEMT-oscillator with low current consumption - mono (single channel) operation - very small outline dimensions Handling Precautions: - This InnoSenT Sensor is sensitive to damage from ESD. - Normal precautions as usually applied to CMOS devices are sufficient when handling the device. Touching the signal output pins has to be avoided at any time before soldering or plugging the device into a motherboard. Absolute Maximum Ratings: Parameter Symbol Rating Units supply voltage VCC 5.25 V operating temperature (out of spec) TOP - 40 / + 85 °C storage temperature TSTG + 90 °C Electrical Characteristics: Parameter Symbol min. typ. max. units comment transmit frequency ftransmit 24.075 24.125 24.175 GHz output power (EIRP) Pout 16 dBm temperature drift ∆f - 1 MHz/°C antenna pattern Tx (3dB) horizontal 80 ° azimuth vertical 32 ° elevation side lobe suppression horizontal 13 dB azimuth vertical 13 dB elevation IF output voltage offset -300 300 mV supply voltage VCC 4.75 5.0 5.25 V supply current ICC 30 40 mA operating temperature TOP - 20 + 60 °C outline dimensions ~ 25 x 25 x 7 mm Interface: The sensor provides a 2.54mm grid, single row pin header (square pin 0.635mm) Pin # Description In/Out Comment 1 VCC input supply voltage (+5 V) 2 IF1 output signal output 3 GND input analog ground
Version 1.0 IPM-165_US page 2 of 3 2007-02-22 Mechanical Outlines: (all dimensions in mm) Approved pulsing conditions to fulfill the FCC requieremts: • ASK modulation with 10kHz and 10% dutycycle (on-time 10µs min.) • Warning: Any other pulsing condition with less than 10µs on-time may void the FCC authorization to operate this equipment. Certification and environment protection: InnoSenT GmbH has established and applies a quality system for: Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances (RoHs – European Union directive 2002/95/EG). FCC approval • This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. • Manufacturers of mobile or fixed devices incorporating IPM-165 modules are authorized to use the FCC Grants and IC Certificates of the IPM-165 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS-IPM165" and "Contains IC: 6902A-IPM165".
Version 1.0 IPM-165_US page 3 of 3 2007-02-22 Contact Information: InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0 Fax: +49 (0) 9528-9518-99 E-Mail: info@InnoSenT.de Web: www.InnoSenT.de

Navigation menu