Inovonics Wireless 3B6AVBLP ANALOG VOICE BELTPACK User Manual Installation Instructions

Inovonics Wireless Corporation ANALOG VOICE BELTPACK Installation Instructions

Users Manual

1 QSR Performance Solutions Drive Thru System - Installation Instructions What Is Included 1 — Base Station w/ 13.5 VDC power adaptor 1 — Programming station w/ 18” cable 1 — Microphone for inbound audio 1 — Speaker for outbound audio 1 Lot — Acoustic foam for speaker post Varies Per Order — Belt-packs w/ pouch 1 — Battery per Belt-Pack (w/1 additional battery when 4 or more belt-packs are ordered) Varies Per Order — Headsets (1 per belt-pack) 1 — Battery charger w/ 5 VDC power adaptor What Is Not Included • Cable to connect Base to speaker post equipment (3 separately jacketed, shielded, twisted pairs, minimum 20 gauge stranded) • Vehicle detection loop • Optional grill speaker (8 ohms) • Speaker post • Conduit from inside restaurant to speaker post • Miscellaneous hardware • Tools Installation Steps 1. Begin charging batteries prior to installing system 2. Determine best location for Base • Needs electrical outlet (power adaptor has 6 foot cable) • Maintain 3 feet clearance from large metal objects and electrical or electronic equipment • Relative close proximity to drive thru booth(s) but avoid installing where base cannot be ser-viced without interrupting normal business operations • Be mindful of where conduit to speaker post terminates inside • Programming station connects to base with 18” cable and needs to be at a height and location that is accessible to restaurant employees 3. Install cabling from speaker post to Base location. 3 individually shielded, jacketed, twisted pairs, mini-mum 20 gauge stranded. 4. Mount Base and connect cables (keep power cable and transformer at least 6 inches from left side of Base) 5. Mount programming station within 18” of Base, and at an accessible height and connect cable 6. Mount vehicle detector and connect to Base, and to cable feeding to loop at speaker post 7. Install speaker and microphone in speaker post and connect cables, including connection to vehicle detector loop. Solder all splices. • IMPORTANT! Speaker and microphone inside of speaker post MUST be acoustically and me-chanically isolated from each other AND the speaker post with foam rubber or an acoustic dampening material to insure quality audio performance. • In a typical speaker post the microphone would be mounted in the top section, closer to the person placing the order. The speaker should be at least 2 feet away from the microphone, typically mounted lower.
2 Installation Steps — cont. 8. Make sure jumpers in Base are configured to match your installation (see Base Station Controls dia-gram) • J1 & J2 — Separate speaker & mic or one device serving as both • J4 — Detection type: closure or pulse • J5 — Full-duplex or Standard (half-duplex) • J6 — Full-duplex click suppression 9. Turn on power to base 10. Insert batteries in belt-packs and program per instructions on programming station 11. Connect headsets to belt-packs and test range, reception, audio quality, and volume 12. Adjust volume levels as needed 13. Test vehicle detection 14. Train restaurant employees and manager QSR Drive Thru Solutions - Batteries & Charger Charging Indicators — Will light red when battery is charging and change to green when battery is charged Charging Ports for Batteries Holes for Wall Mount Screws NOTES: • Batteries are Lithium-Ion • Batteries require about 3 hours to charge • Batteries will hold a charge for about 8 to 10 hours during normal use • When the battery voltage becomes too low, a short warble tone, occurring at five–second intervals is heard in the headset. After 2 minutes the headset will shut off. • Batteries should be removed from belt-pack and stored in charger when not being used.
3 QSR Performance Solutions - Base Station Front Cover Indicators & Controls Channel Indicators Indicates which one of the eight channel frequencies is being used Page Indicator Lights when the Page button is pressed on a belt-pack Talk Indicator Lights when the Talk button is pressed on a belt-pack Power Switch Used to turn power to base off & on. Turn off to enable optional wired backup if one is installed. Power Indicator Lights when power is applied to base. Day / Night Volume Switch Day position enables DAY outgoing volume control. Night position enables NIGHT outgoing volume control. Grill Monitor Volume Adjusts the volume of the optional grill speaker Vehicle Indicator Lights when vehicle is detected at speaker post
4 QSR Performance Solutions - Base Station Controls Must jump upper pins when system is half-duplex. Jump lower pins to eliminate clicking when TALK button is pressed with full-duplex system Set to HIGH if inbound level in headsets is low when used in TALK-LOCK Connects to optional inter-nal vehicle detect board When a single device is used as the speaker and mic at the menu board, jump pins 1 & 2 on J1 and J2. Jump pins 2 & 3 on J1 and J2 when a separate speaker and mic are used. Connects to micro-phone at menu-board. Should have a 1500 ohm resistor installed in series on both legs of mic line. Connects to menu-board speaker. When using 1 device as a speaker and mic, use this connection. To grill speaker Used with greeters Not normally used Connects to cross-lane module in 2 lane system Connects to one leg of vehicle detector contact closure Connects to cross-lane module in 2 lane system Connects to greeters and cross-lane modules To other leg of contact closure on vehicle de-tector and supplies power to interconnect module relay Used with greeters Not normally used To headset programming station To 13.5 VDC power transformer Determines if outgoing audio is Day or Night level Grill speaker master volume Outgoing audio to menu-board speaker Used to allow base to recognize new jumper and channels Power switch Individual vol-ume controls for grill speaker Configures outside speaker and mic for full or half duplex Jump pins 1 & 2 for air-switch detector. Jump pins 2 & 3 for sodar or loop detector Jump pins 1 & 2 to des-ignate base as Lane 1. Jump pins 2 & 3 to des-ignate base as Lane 2. Use to change frequency of base. Frequencies 1 - 8 with J3 set to Lane 1. Frequencies 9 - 16 with J3 set to Lane 2. Vehicle alert tone volume in headsets Jump pins 1 & 2 to lower grill speaker volume when TALK is activated. Use to reduce feedback. Incoming audio volume from menu-board mic Turns optional Noise Reduction off and on
5 Loop Detector Normally Open Loop QSR Performance Solutions - Connections To Base Grill Speaker (optional) Power Adaptor Programming Station Vehicle Detector Loop Speaker Post Base Connection Terminal Do not terminate shield at microphone end
6 7. Talk 2 • Has the exact same function as Talk 1 when used with a single lane system • On Dual and Cross Lane systems Talk 2 will be programmed to communicate with Lane 2 8. Talk 1 • Activates communication to outside speaker • Will also be heard by other headsets and possibly grill speaker (depending on system configuration) • Can be used to test incoming and outgoing audio even when no car is present • On half-duplex systems, press to talk and release to listen • On full-duplex systems incoming audio will be heard even while Talk 1 is pressed • On Dual and Cross Lane systems Talk 1 will be programmed to communicate with Lane 1 9. Headset Jack • The 2 prong headset connector plugs in here 10. Battery Compartment • Battery goes here 11. Battery Release • Slide back to release battery from compartment 1. Page • Press to talk to the other headsets without being heard at the speaker post • Belt-packs can be programmed for Page Monitor Mode, they will only hear communication from other belt-packs that are using the Page button and will not hear communication to or from the speaker post • To program a belt-pack for Page Monitor Mode, hold Page button down while powering the headset on. • To exit Page Monitor Mode turn the belt-pack off and back on 2. Volume Down • Listening volume can be adjusted in 7 steps from the lowest to high-est setting. When the belt-pack is powered on, the listening level will be near mid-level and can be adjusted 3 steps up or 4 steps down. A short tone will be heard each time the volume is adjusted. A long tone is heard when the lowest or highest level is reached. 3. Volume Up • Turns up incoming audio from speaker post. See previous section for details 4. Power LED • Green when belt-pack is powered on • Red when talk-lock is in use • Flashes green during channel programming 5. Power On / Off • Press to turn power to belt-pack on or off 6. Talk Lock • Used with a full-duplex system, press to activate hands-free com-munication • When car arrives at speaker post, press to activate. Communication will automatically deactivate when car leaves speaker post and automatically reactivate when next car arrives • Press Talk 1 or Page to deactivate Talk Lock • Only 1 belt-pack at a time can use Talk Lock and no other headsets can talk to the speaker post • Disabled or enabled by holding Talk Lock button down when the headset is being powered up QSR Performance Solutions Drive Thru - Belt-Pack 1 2 3 4 5 6 7 8 9 10 11 Bottom View

Navigation menu