Inseego NVWGSM0508 Expedite L10-G , GSM0508-40 User Manual CNN0301IG001 HS 3001

Novatel Wireless Inc Expedite L10-G , GSM0508-40 CNN0301IG001 HS 3001

User manual

GSM0508IG001Expedite L10-GIntegration GuideVersion: 1.00 Wednesday, May 07, 2014
i novatelwireless.comGeneralTERMS OF USE OF NEW MATERIALS - PLEASE READ CAREFULLYFrom time to time, Novatel Wireless, in its sole discretion, may make available for downloadon its website (www.novatelwireless.com), or may transmit via mail or email, updates orupgrades to, or new releases of, the firmware, software or documentation for its products(collectively, 'New Materials'). Use of such New Materials is subject to the terms andconditions set forth below, and may be subject to additional terms and conditions as set forthin Novatel Wireless's Technical Support Policy (posted on its website) and/or any writtenagreement between the user and Novatel Wireless.All New Materials are provided AS IS. Novatel Wireless makes no warranty or representationwith respect to the merchantability, suitability, functionality, accuracy or completeness of anysuch New Materials. The user of such New Materials assumes all risk (known or unknown) ofsuch use. Novatel Wireless reserves all rights in such New Materials. The user shall have only arevocable and limited license to use such New Materials in connection with the products forwhich they are intended. Distribution or modification of any New Materials without NovatelWireless's consent is strictly prohibited.IN NO EVENT WILL NOVATELWIRELESS BE RESPONSIBLE FOR ANY INCIDENTAL,INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES AS A RESULT OF THE USE OF ANYNEW MATERIALS. NOVATELWIRELESS 'S MAXIMUM LIABILITY FOR ANY CLAIM BASEDON THE NEW MATERIALS SHALL NOT EXCEED FIFTY U.S. DOLLARS ($50).Version VerificationPlease ensure you have the latest version of this document by downloading it fromwww.novatelwireless.com
ii novatelwireless.comCopyright© 2014 Novatel Wireless. All rights reserved. Complying with all applicable copyright laws isthe responsibility of the user. Without limiting the rights under copyright, no part of thisdocument may be reproduced, stored in or introduced into a retrieval system, or transmittedin any form or by any means (electronic, mechanical, photocopying, recording or otherwise),or for any purpose, without the express written permission of Novatel Wireless.Novatel Wireless and the Novatel Wireless logo are either registered trademarks ortrademarks of Novatel Wireless, Inc. in the United States.251 Renner Pkwy, Suite 200Richardson, TX 75080 USAPhone: (972) 633-4400Fax: (972) 633-4444Email: info@nvtl.comwww.novatelwireless.com
iii novatelwireless.comWarranty InformationThis warranty applies to (a) products sold directly by Novatel Wireless, unless a differentwarranty is specified in a written agreement between Novatel Wireless and the purchaser;and (b) products sold to end users through a distributor authorized by Novatel Wireless, butonly where the authorized distributor does not provide a separate warranty on such products,and Novatel Wireless has agreed to provide this warranty to such end users. If you purchasedthe product from an authorized distributor, please check whether this warranty from NovatelWireless or a separate warranty from the distributor applies to your purchase. This warrantydoes not apply to any (i) accessories or batteries for the products; or (ii) demonstrationsamples or prototypes of the products. Unless otherwise provided in a written agreementbetween Novatel Wireless and the purchaser, all such accessories, batteries, samples orprototypes are provided by Novatel Wireless AS IS without any warranty of any kind.Novatel Wireless warrants to the original purchaser of the product from Novatel Wireless orits authorized distributor (as applicable) that, for a period of one (1) year from the date ofshipment of the product from Novatel Wireless, the product hardware will be substantiallyfree from defects in material or workmanship under normal operation, and the productfirmware will perform substantially in accordance with the product documentation providedby Novatel Wireless. Novatel Wireless does not warrant that (a) the product hardware orfirmware will meet the purchaser's requirements; (b) the operation of the product hardwareor firmware will be uninterrupted or error-free; or (c) the product, when integrated in, orcombined with, other products or software not supplied by Novatel Wireless, will continue toperform substantially in accordance with the product documentation. This limited warranty isfor the benefit of the original purchaser, and is not transferable.During the warranty period, Novatel Wireless, at its expense and in its sole discretion, willrepair the product, or replace the product with a corresponding or equivalent product, if it isdetermined to have a covered defect, provided that the purchaser first notifies NovatelWireless (directly or through its authorized distributor from which the product waspurchased) of any such defect, furnishes Novatel Wireless with a proof of purchase (ifrequired), requests and obtains a return merchandize authorization (RMA) number fromNovatel Wireless, and returns the product under that RMA to Novatel Wireless (or, at NovatelWireless option, to its authorized distributor), with the shipping charges being prepaid bypurchaser. If, upon reasonable examination of the returned product, Novatel Wireless doesnot substantiate the defect claimed by purchaser, or determines that the defect is notcovered under this limited warranty, Novatel Wireless will not be required to repair or replacethe product, but may instead reship the product to the purchaser (or, at Novatel Wireless'option, to its authorized distributor where the product can be made available to purchaser), inwhich case the purchaser shall be responsible for paying Novatel Wireless' cost for reshippingthe product to purchaser (or to Novatel Wireless' authorized distributor), and NovatelWireless' usual charges for unpacking, testing, and repacking the product for reshipment to
iv novatelwireless.compurchaser (or to Novatel Wireless' authorized distributor).Purchaser shall bear the risk of lossor damage in transit to any product returned by purchaser to Novatel Wireless, or anyreturned product not found to be defective or covered under this warranty, and reshipped byNovatel Wireless to purchaser (or to Novatel Wireless' authorized distributor). In the eventNovatel Wireless repairs or replaces a defective product covered by this limited warranty, therepaired or replacement product will be covered under this limited warranty for theremainder of the original warranty period on the defective product, or a period of ninety (90)days, whichever is longer. If Novatel Wireless is unable to repair or replace a defectiveproduct covered by this limited warranty, Novatel Wireless will provide to purchaser a creditor a refund (at Novatel Wireless' option) of the original purchase price (excluding taxes andshipping charges). Any returned and replaced product, or any product for which NovatelWireless has furnished a credit or a refund, becomes the property of Novatel Wireless.Novatel Wireless shall not have any obligation to provide any firmware bug fixes, upgrades ornew releases except as may be necessary to correct any covered defect of which purchasernotifies Novatel Wireless in writing during the warranty period. Novatel Wireless, from timeto time and in its sole discretion, may make available for download on its website(www.novatelwireless.com), or may provide via email, certain firmware bug fixes, upgradesor new releases for the product. Download and use of any such bug fixes, upgrades or newreleases is subject to all of the applicable terms and conditions of Novatel Wireless' technicalsupport policy as posted and updated on its website.Novatel Wireless shall have no obligation under this limited warranty for (a) normal wear andtear; (b) the cost of procurement of substitute products; or (c) any defect that is (i)discovered by purchaser during the warranty period but for which purchaser does notrequest an RMA number from Novatel Wireless, as required above, until after the end of thewarranty period, (ii) caused by any accident, misuse, abuse, improper installation, handling ortesting, or unauthorized repair or modification of the product, (iii) caused by use of anymaterials not supplied by Novatel Wireless, or by use of the product other than in accordancewith its documentation, or (iv) the result of electrostatic discharge, electrical surge, fire, floodor similar causes.The purchaser (or its customers, as applicable) shall be solely responsible for the properconfiguration, testing and verification of the Novatel Wireless product prior to deployment inthe field, and for ensuring that any end user product or system into which the NovatelWireless product is integrated or incorporated operates as intended and meets therequirements of purchaser (or its customers). Novatel Wireless shall have no responsibilitywhatsoever for the integration, configuration, testing, verification, installation, upgrade,support or maintenance of any such end user product or system, or for any liabilities,damages, costs or expenses associated therewith.
v novatelwireless.comNOVATEL WIRELESS' SOLE RESPONSIBILITY AND PURCHASER'S SOLE REMEDY UNDERTHIS LIMITED WARRANTY SHALL BE FOR NOVATEL WIRELESS TO REPAIR OR REPLACETHE PRODUCT (OR IF REPAIR OR REPLACEMENT IS NOT POSSIBLE, PROVIDE A CREDITOR REFUND OF THE PURCHASE PRICE) AS PROVIDED ABOVE. NOVATEL WIRELESSEXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED,INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT,MERCHANTABILITY, SATISFACTORY PERFORMANCE AND FITNESS FOR A PARTICULARPURPOSE. IN NO EVENT SHALL NOVATEL WIRELESS BE LIABLE FOR ANY INDIRECT,SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDINGWITHOUT LIMITATION LOSS OR INTERRUPTION OF USE, DATA, REVENUES OR PROFITS)RESULTING FROM A BREACH OF THIS WARRANTY OR BASED ON ANY OTHER LEGALTHEORY, EVEN IF NOVATEL WIRELESS HAS BEEN ADVISED OF THE POSSIBILITY ORLIKELIHOOD OF SUCH DAMAGES.Some jurisdictions may require a longer warranty period than specified above and,accordingly, for products sold in those jurisdictions the applicable warranty period shall beextended as required under the laws of those jurisdictions. Furthermore, some jurisdictionsmay not allow the disclaimer of implied warranties or the exclusion or limitation of incidentalor consequential damages, so the above disclaimer, limitation or exclusion may not apply toproducts sold in those jurisdictions. This limited warranty gives the purchaser specific legalrights and the purchaser may have other legal rights that vary from jurisdiction to jurisdiction.This limited warranty shall be governed by the laws of the State of Texas, United States ofAmerica, without regard to conflict of laws principles. This limited warranty shall not begoverned in any respect by the United Nations Convention on Contracts for the InternationalSale of Goods.
vi novatelwireless.comRegulatory ComplianceFCC CERTIFICATIONNovatel Wireless certifies that the Expedite L10-G GSM Radio Module complies with the RFrequirements applicable to broadband PCS equipment operating under the authority of 47CFR Part 24, Subpart E and Part 22 Subpart H of the FCC Rules and Regulations. Thiscertification is contingent upon installation, operation and use of the Expedite L10-G moduleand its host product in accordance with all instructions provided to both the OEM and enduser. When installed and operated in a manner consistent with the instructions provided, theExpedite L10-G module meets the maximum permissible exposure (MPE) limits for generalpopulation / uncontrolled exposure as defined in Section 1.1310 of the FCC Rules andRegulations.The Expedite L10-G module is designed for use in a variety of host units, enabling the hostplatform to perform wireless data communications. However, there are certain criteria relativeto integrating the modem into a host platform such as a PC, laptop, handheld, monitor andcontrol unit, etc. that must be considered to ensure continued compliance with FCCcompliance requirements.Important Information for Canada/USA OEM IntegratorsThis section provides guidance for using the Expedite L10-G in host devices through the FCCPermissive Change process. When utilizing the permissive change process, Novatel Wireless,the grantee, is responsible for all integrations and must be consulted on all regulatory mattersinvolving the Expedite L10-G.The Expedite L10- G module is granted with FCC/IC modular approval for mobile 1applications, and may be installed as a standalone2transmitter in final products meeting thefollowing conditions. If the following conditions are followed, it may be used in final productswithout additional FCC/IC certification. Otherwise, additional FCC/IC approvals must beobtained.1Mobile Device Definition – FCC defines as a transmitting antenna located at a distance ≥20cm from the user.2Standalone is defined as a single transmitter transmitting as opposed to 2 or moretransmitters transmitting simultaneously.
vii novatelwireless.comThe antenna connected to the Expedite L10-G module must be installed to provide atleast 20 cm separation from the human body at all times.The Expedite L10-G module and transmitter antennas must not be co-located with anyother transmitter or antenna within a host device.The transmitter antenna used with the Expedite L10-G module must not exceed thefollowing level:Cellular maximum permitted antenna gain: 5.39dBiPCS band maximum permitted antenna gain: 3.31dBiTo comply with the aspects of KDB996369, strict adherence to the design parameters inSection 4.1.1.3 Antenna And RF Signal Trace must be observed. Section 4.1.1.3 providesPCB RF trace design guidelines for the coplanar microstrip between the Expedite L10-GRF compression pads and the U.FL style coaxial connector.A label containing the FCC and Industry Canada IDs must be permanently affixed to theexterior of the host device into which the Expedite L10-G module is installed. The labelmay also be under a panel or battery pack if it is readily accessible and cannot beseparated from the host device itself. The label must contain a statement similar to thefollowing;This device contains FCC ID: PKRNVWGSM0508This equipment contains equipment certified under IC: 3229A-GSM0508If any of these conditions are not met then additional information should be sought from theFCC or an FCC qualified test laboratory.If the Expedite L10-G module is intended for use in a portable1device, the OEM integrator isresponsible to design the product to comply with RF exposure, and must work with NovatelWireless (the grantee) to satisfy FCC/IC SAR requirements. Refer to FCC OET Bulletin 65Supplement C for information about FCC RF exposure compliance requirements for mobileand portable devices.The system user manuals and other documentation must clearly indicate operating conditionsthat must be observed to ensure compliance with FCC/IC RF exposure guidelines and alsoinclude appropriate caution and warning statements and information.The host device containing the Expedite L10-G module may also require compliance to FCCPart 15 Subpart B – Unintentional Radiators.1Portable Device Definition – FCC defines as a transmitting antenna located at a distance ≤20cm from the user.
viii novatelwireless.comFCC NOTICE TO USERSNovatel Wireless has not approved any changes or modifications to this device by the user.Any changes or modifications could void the users authority to operate the device. See 47CFR Sec. 15.21. The device complies with part 15 of the FCC rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may causeundesired operation. See 47 CFR Sec. 15.19.This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there isno guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined byturning the equipment off and on the user is encouraged to try to correct the interference byone or more of the following measures:lReorient or relocate the receiving antenna.lIncrease the separation between the equipment and receiver.lConnect the equipment into an outlet on a circuit different from that to which thereceiver is connected.lConsult the dealer or an experienced radio/TV technician for help.If the FCCID of the module is not visible when installed in the host platform, then apermanently attached or marked label must be displayed on the host unit referring to themodule.The label should contain wording such as:Contains FCC ID: PKRNVWGSM0508This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) This device mustaccept any interference received, including interference that may cause undesired operation.Industry CanadaIC: 3229A-GSM0508 MODEL NUMBER: GSM0508This device complies with Industry Canada RSS standard(s). Operation is subject to thefollowing two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of thedevice.
ix novatelwireless.comIn order to use the Expedite L10-G module without any additional FCC certification theinstallation must meet the following conditions:The system antenna(s) connected to the Expedite L10-G module must be installed toprovide at least 20 cm separation from the human body during normal operation.The system antennas must not be co-located with any other transmitter or antenna.The system antenna(s) used with the Expedite L10-G module must not exceed thefollowing level:Cellular maximum permitted antenna gain: 5.39dBiPCS band maximum permitted antenna gain: 3.31dBiLe présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareilne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter toutbrouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement.Afin d'utiliser le Expedite L10-G module sans aucune certification de d'Industrie Canadasupplémentaire l'installation doit satisfaire aux conditions suivantes:L'utilisation du système connectée au module de Expedite L10-G doit être installée pourfournir la séparation d'au moins 20 cm du corps humain pendant une opération normale.Les antennes du système ne doivent pas être colocalisés avec un autre émetteur ouantenne.L'utilisation du système utilisée avec le module de Expedite L10-G ne doit pas dépasserles niveaux suivants:Cellulaires le permis gain maximal est de 5.39dBiPCS groupent le gain maximal est de 3.31dBiROHS COMPLIANCEAs a part of Novatel Wireless’ corporate policy of environmental protection, Novatel Wirelesstakes every step to ensure that the Expedite L10-G modules are designed and manufacturedto comply to the European Union Directive 2002/95/EC for the Restriction of HazardousSubstances (RoHS).CE (European Union Notice)If this product has telecommunications functionality, it also complies with the essentialrequirements of the following EU Directive:* R&TTE Directive 1999/5/EC
x novatelwireless.comCompliance with these directives implies conformity to harmonized European standards(European Norms) that are listed in the EU Declaration of Conformity issued by NovatelWireless Inc. for this product or product family.This compliance is indicated by one of the following conformity markings placed on theproduct. This CE marking is valid for EU non-harmonized telecommunications products “CE0560”NCC NOTICE「減少電磁波影響,請妥適使用」NCC ID: CCAF133G0170T1
xi novatelwireless.comImportant Safety InformationThe following information applies to the devices described in this manual. Always observe allstandard and accepted safety precautions and guidelines when handling any electrical device.lSave this manual: it contains important safety information and operating instructions.lDo not expose the Expedite L10-G product to open flames.lEnsure that liquids do not spill onto the devices.lDo not attempt to disassemble the product: Doing so will void the warranty. Thisproduct does not contain consumer-serviceable components.The Enabler Expedite L10-G module may not be used in an environment where radiofrequency equipment is prohibited or restricted in its use. This includes aircraft, airports,hospitals, and other sensitive electronic areas.Do not operate RF devices in an environment that may be susceptible to radio interferenceresulting in danger, specifically;lAreas where prohibited by the law.lFollow any special rules and regulations and obey all signs and notices. Alwaysturn off the host device when instructed to do so, or when you suspect that it maycause interference or danger.lWhere explosive atmospheres may be present.lDo not operate your modem in any area where a potentially explosive atmospheremay exist. Sparks in such areas could cause an explosion or fire resulting in bodilyinjury or even death. Be aware of and comply with all signs and instructions.lUsers are advised not to operate the modem while they are at a refueling point orservice station.lUsers are reminded to observe restrictions on the use of radio equipment in fueldepots (fuel storage and distribution areas), chemical plants or where blastingoperations are in progress.lAreas with a potentially explosive atmosphere are often but not always clearly marked.lPotential locations can include gas stations, below deck on boats, chemical transferor storage facilities, vehicles using liquefied petroleum gas (such as propane orbutane), areas where the air contains chemicals or particles, such as grain, dust ormetal powders, and any other area where you would normally be advised to turnoff your vehicle engine.lNear Medical and life support equipment.lDo not operate your modem in any area where medical equipment, or life supportequipment may be located, or near any equipment that may be susceptible to anyform of radio interference. In such areas, the host communications device must beturned off. The modem may transmit signals that could interfere with thisequipment.lOn an aircraft, either on the ground or airborne.lIn addition to FAA requirements, many airline regulations state that you mustsuspend wireless operations before boarding an airplane. Please ensure that thehost device is turned off prior to boarding an aircraft in order to comply with theseregulations. The modem can transmit signals that could interfere with variousonboard systems and controls.
xii novatelwireless.comlWhile operating a vehiclelThe driver or operator of any vehicle should not operate a wireless data device.Doing so will detract from the driver or operator's control and operation of thatvehicle. In some countries, operating such communication devices while in controlof a vehicle is an offense.DisclaimerThe information and instructions contained within this publication comply with all FCC, GCF,PTCRB, R&TTE, IMEI and other applicable codes that are in effect at the time of publication.Novatel Wireless disclaims all responsibility for any act or omissions, or for breach of law, codeor regulation, including local or state codes, performed by a third party.Novatel Wireless strongly recommends that all installations, hookups, transmissions, etc., beperformed by persons who are experienced in the fields of radio frequency technologies.Novatel Wireless acknowledges that the installation, setup and transmission guidelinescontained within this publication are guidelines, and that each installation may have variablesoutside of the guidelines contained herein. Said variables must be taken into considerationwhen installing or using the product, and Novatel Wireless shall not be responsible forinstallations or transmissions that fall outside of the parameters set forth in this publication.Novatel Wireless shall not be liable for consequential or incidental damages, injury to anyperson or property, anticipated or lost profits, loss of time, or other losses incurred byCustomer or any third party in connection with the installation of the Products or Customer'sfailure to comply with the information and instructions contained herein.
xiii novatelwireless.comTable of Contents1 Introduction 1Technical Specifications 3General 3Radio Technology 3Speech Features 3Supplementary Services 3USB/UART Features 3SMS Features 3SIM-Based Features 3Customized Features 4Multiple Configurations 4Customer Tool 4Design Package 5Power 5Environmental 5Packet Data Transfer 5Regulatory 5Reference Documents 6Typical Usage 7Contacting Novatel Wireless 72 Module Power 8Operating Power 9Typical Input Current 93 Interfaces 10I/O Connector Pin Assignments 11
xiv novatelwireless.comAnalog Audio Interface 14Speaker 14Microphone 1515Microphone Type Support 15Headset 16Specific Absorption Rate (SAR) Guidelines 18SAR Compliance 183 Tune Up Procedures 19Tune Up Procedure 20
1 novatelwireless.com1IntroductionTechnical SpecificationsTypical UsageContacting Novatel Wireless
2 novatelwireless.comThe Expedite L10-G 2G data modem is a small wireless data modem providing 2G wirelessdata connectivity for portable and hand held computers, point-of-sale devices, and othermachine-to-machine applications.It is a compact, wireless OEM module that uses the Global System for Mobile Communications(GSM) international communications standard to provide two-way wireless capabilities. TheExpedite L10-G module is a fully approved GSM device, enabling application-specific, two-way communication and control.The small size of the Expedite L10-G module allows it to integrate easily into the applicationand packaging.Figure 1-1 Expedite L10-G Module
3 novatelwireless.comTechnical SpecificationsGeneralName: Expedite L10-GModel: GSM0508-40Radio TechnologyQuad-band EDGE/GSM/GPRS: 850/900/1800/1900 MHzClass: Supports class 8, 10 and 12 (The default GPRS class is 8)Modulation Coding Schemes: CS-1 to CS-4Mode of Operation: Class B (attaches to both GSM and GPRS at the same time)Speech FeaturesSpeech Codec: AMR HR FR EFRSpeech Interface: Analog/PCMSupplementary ServicesSpeech Codec: Number identificationCall OfferingCall CompletionMulti-Party USSDUSB/UART FeaturesUSB 1.1: For download image only.USB VID/PID: MTK’s VID/PID as 0E8D/0003, Only for download mode.UART1 (2-wire): For download image and debug portUART2 (4 wire): CMUX SupportSMS FeaturesSMS over GPRS: Mobile Originated and Mobile TerminatedConcatenated SMS: Yes, up to 10 messagesSMS Cell Broadcast: Supported by AT commandsSMS Immediate Notification: Supported by AT commandsSIM-Based FeaturesSIM Personalization Locks: SIM Lock/Network lock , Supports restricting SIM/USIM cardSIM Application Toolkit: Supported by AT commands
4 novatelwireless.comCustomized FeaturesNotification for incoming call and SMS: Provide one GPIO pin for notificationHost wake-up modem event: Provide one interrupt pin to wake-up modemModem AT command ready event: Provide one GPIO pin to notify host that AT command is readyCMUX: Supports CMUX featureBoot up ready message: Shows “AT Command Interpreter Ready” as boot up readyMonitor modem power on/off status: Provide a resistor – VEXT28 to monitor the power on/off status ofmodemAT command to adjust the band, chan-nel and output max power:For verifying the RF power in customer product.Multiple ConfigurationsAT command to switch speech inter-face (Analog/PCM):1. Supports to switch speech interface between PCM and analog.AT command to change UART2’s baudrate:1. Supports baud rate up to 921,600 bps2. The default baud rate of UART2 is 115,200 bpsAT command to change GPRS class: 1. Supports class 8, 10 and 122. The default GPRS class is 8AT command to change UART2 flowcontrol:1. Supports to change the UART2’s flow control as None, HW flow controland SW flow control2. The default flow control is none flow controlAT command to read the operatordata (MCC/MNC):1. Read Network Lock DataAT command to read the network lockpassword:1. Read Network Lock PasswordCustomer ToolDebug tool: Catcher tool execution package Supports Windows XP, Windows Vistaand Windows 7Catcher tool user guide: Catcher_Tool_user_guide-v0.1-2013.05.31.pdfFlash tool: Flash tool execution package Supports Windows XP, Windows Vista andWindows 7Flash tool user guide: Flash_Tool_user_guide-v0.1-2013.05.31.pdfTx Power Adjust tool: USI_TX_Power_Adjust_Tool-V0.1-20130829.pdfIMEI re-write tool: IMEI_API_Introduction-V0.1-20130923.pdf
5 novatelwireless.comDesign PackageUpgrade agent introduction: 1. BROM_Lite_Introduction-v0.2-20130709.pdf2. System Information to build the BROM lite tool-v0.1-2013.07.09.pdfCompare between BROM Lite andFlash Tool:BROM_Lite_vs_Flash_Tool-V0.1-2013.06.10.pdfCMUX sample code (Linux): smmux-alpha-2.tar.gzCMUX introduction: 1. CMUX_introduction-v0.1-2013.05.31.pdf2. pppd.7zUART flow control introduction: UART_Flow_Control-v0.1-2013.05.31.pdfAT Command set: Expedite L10-G_AT_Command_Set_v0.8.6_20131008.docAudio parameter adjustment: Expedite L10-G_Audio_Parameter_Adjustment-V0.3-2013.08.22.pdfThe user guide of AT command toadjust the band, channel and outputmax power:AT_ERFTX-V0.1-20130924.pdfPowerElectrical Power: 3.3 to 4.35 Vdc (vbat)Supply Vripple must be less than 200 mV across all frequenciesPeak currents and average powerdissipation:Refer to the Operating Power table in the Technical Specifications forpeak currents and average power dissipation for various modes of oper-ation.EnvironmentalCompliant Operating Temperature: -20 °C to 60 °COperating Temperature: -30 °C to 70 °CStorage Temperature: -40 °C to 85 °CHumidity: Up to 95% non condensingEmissions: FCC 47 CFR Parts 2,15,22 & 24Packet Data TransferProtocol:Short Message Services: Text, MO/MTRegulatoryAgency approvals: FCC CertificationIndustry CanadaPTCRBCEGCF
6 novatelwireless.comReference DocumentsCNN0401xAT001 - HS 3002 AT Command ReferenceCNN0401xTG001 - HS 3002 Transition GuideENF0000SD001 - HDK GuideCNN0401AN001 - Using Digital Audio on the HS 3002
7 novatelwireless.comTypical UsageThe following applications can use the Expedite L10-G module for transmitting/receivingdata/voice:lAutomated Meter Reading (AMR)lPoint of Sale Applications (POS)lE-mail and Internet accesslAutomated Vehicle Location (AVL)lMachine to Machine communication (M2M)lTelematicslTelemetrylWireless SecuritylSmart PhoneslTelemedicineContacting Novatel WirelessFor technical support and customer service dealing with the modem itself, contact thecompany where you purchased the product. If you purchased the product directly fromNovatel Wireless, visit the Support page on the Novatel Wireless web site:www.novatelwireless.com
8 novatelwireless.com2Module PowerOperating Power
9 novatelwireless.comOperating PowerThe Expedite L10-G module requires an in/out voltage of 3.3V to 4.35V. The supply ripplemust be less than 200 mV across all frequencies.Typical Input CurrentTypical Results @ 3.8 V 25 deg C, with 1 μF at connector input on VBAT and RF terminated intoa 50Ωresistive load. Traffic Data Rate: FullBand Mode Avg(mA)Peak(mA) NotesGSM850 PCL=5, TX=32.5dBm 211 1810 GPRS, 1TXPCL=19, TX=5dBm 59.8 -EGSM PCL=5, TX=32.5dBm 231 2040 GPRS, 1TXPCL=19, TX=5dBm 59.6 -DCS PCL=0, TX=29.5dBm 142 1140 GPRS, 1TXPCL=15, TX=0dBm 57.3 -PCS PCL=0, TX=29.5dBm 149 1190 GPRS, 1TXPCL=15, TX=0dBm 57.9 -Both Sleep with Paging Multi-frames=5 <1 90 Modem registered; peak during network activityBoth Sleep < 0.9 -Both Shutdown 0.25 0.3 For minimum current draw in shut down mode, werecommend you shut down the modem by eithersending AT$OFF (AT$OFFDLY must be >0) or by send-ing a pulse on PON line (pin 35), and then setting theON/OFF line (pin 37) low to remove power from thedevice.
10 novatelwireless.com3InterfacesI/O Connector Pin AssignmentsAnalog audio interfaceSpecific Absorption Rate (SAR) Guidelines
11 novatelwireless.comFigure 3-1 Pin 1 Reference, 68-Pin I/O ConnectorI/O Connector Pin AssignmentsThe following table shows the pin assignments for the input/output connector.Pin Function Description Notes01 GND Ground02 DAIPCMIN PCM data in 2.8V03 Reserve Pin Reserved for debug04 DAISYNC PCM sync 2.8V05 Reserve Pin Reserved for debug06 Reserve Pin Reserved for debug07 VSIM1 LDO - VSIM output.Provide 1.8/3.0Vto SIM card.1.8/3.0V
12 novatelwireless.comPin Function Description Notes08 PWR_KEY Power Key to enable MT6260internal PMU1.8V~2.8V09 GPIO/INT1 General Purpose I/O,For cus-tomize./INT12.8V10 ACCDET Headset Microphone detect 2.8V11 AP_READY_INT INTFor Host/AP to wake up ExpediteL10-G module.1.8V12 U2RTS UART2 Request to send 2.8V13 NOTIFY_AP Notification for incoming call andSMS1.8V14 U2CTS UART2 Clear to send 2.8V15 U2RXD UART2 Serial Data Output 2.8V16 U2TXD UART2 Serial data input 2.8V17 GND Ground18 EAR_EINT Headset Detect 2.8V19 2G_ANT The signal of RF antenna input/out-put.20 JTAG_EN JTAG Strap Pin, pull high 1K to 2.8Vto enable JTAG f2.8V21 GND Ground22 VEXT28 2.8 V out – Reference for externallevel translation2.8V23 VBAT Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V24 VBAT Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V25 GND Ground26 U1TXD UART1 Serial data input 2.8V27 U1RXD UART1 Serial Data Output 2.8V28 GPIO2 General Purpose I/O,For customize. 1.8V29 LED_B LED control Output, VBAT_VA(KPLED)30 GPIO1 General Purpose I/O,For customize. 1.8V31 SPK_OUTN speaker amplifier (-) (Analog) VBAT32 SPK_OUTP speaker amplifier (+) (Analog) VBAT33 MP3_OUT_L headset amplifier Left 2.8V34 MP3_OUT_R headset amplifier Right 2.8V35 GND Ground
13 novatelwireless.comPin Function Description Notes36 SDA28/GPIO I2C Serial clock/General PurposeI/O,For customize.I/O, 2.8V37 SDA28/GPIO I2C Serial data/General PurposeI/O,For customize.I/O, 2.8V38 MIC1_IN- Microphone input (Headset) 2.8V39 MIC1_IN+ Microphone input (Headset) 2.8V40 MIC0_IN- Microphone amplifier negative input 2.8V41 MIC0_IN+ Microphone amplifier positive input 2.8V42 MICBIAS0 Microphone bias 2.8V43 VBUS INPUT POWER for VUSB POWER44 VBAT Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V45 VBAT Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V46 VBAT Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V47 ADCIN1 10-bit A-to-D 2.8V48 Reserve Pin Reserved for debug49 GPIO3 General Purpose I/O, For cus-tomization1.8V50 AT_READY AT command ready signal 1.8V51 Reserve Pin Reserved for debug52 Reserve Pin Reserved for debug53 USB_DM Universal Serial BUS I/O54 Reserve Pin Reserved for debug55 USB_DM Universal Serial BUS I/O56 GPIO/JTRST General Purpose I/O,For cus-tomize./JTAG Test Reset3.3V57 GPIO/JTMS General Purpose I/O,For cus-tomize./JTAG Test Mode Select3.3V58 GPIO/JTDI General Purpose I/O,For cus-tomize./JTAG Test Data In3.3V59 GND Ground60 GPIO/JRTCK General Purpose I/O,For cus-tomize/JTAG Return TCK3.3V61 GPIO/JTCK General Purpose I/O,For cus-tomize./JTAG Test Clock3.3V62 GPIO/JTDO General Purpose I/O,For cus-tomize./JTAG Test Data Out3.3V
14 novatelwireless.comPin Function Description Notes63 SIM1_DATA SIM data I/O VSIM164 SIM1_CLK SIM clock VSIM165 SIM1_RST SIM reset VSIM166 DAIPCMOUT PCM data out I/O, 2.8V67 DAICLK PCM clock I/O, 2.8V68 DAIRST PCM RST I/O, 2.8VTable 3-1 I/O Connector Pin AssignmentsAnalog Audio InterfaceThe Expedite L10-G module provides analog audio interface, include speaker, microphone,and headset.SpeakerPin No. Pin name Description29 SPK_OUTN speaker amplifier (-) (Analog)31 SPK_OUTP speaker amplifier (+) (Analog)Speaker functional specificationSymbol Parameter Min. Typ. Max. UnitIDC Current consumption 4 mASINAD Signal to noise and distortion ratioInput level: -40 dBm0Input level: 0 dBm02969dBdBRLOAD Output resistor load (differential) 16 32 ΩCLOAD Output capacitor load 250 pFICN Idle channel noise of transmit path -67 dBm0XT L-R channel cross talk -66 dBm0Vout Full Scale output voltage SPK_OUT 0.7 VrmsExpedite L10-G integrate class-AB audio AMP, the following table is the maximum outputpower:Test ConditionMaximum outputpowerSPK_OUTN 0.87W3.3V, 8 ohm THD+N=1% 0.53W4.2V, 8 ohm THD+N=10% 1.08W3.3V, 8 ohm THD+N=10% 0.65WSpeaker reference circuit
15 novatelwireless.comMicrophonePin No. Pin name Description40 MIC1_IN- Microphone input (Headset)41 MIC1_IN+ Microphone input (Headset)42 MIC0_IN Microphone amplifier negative input43 MIC0_IN+ Microphone amplifier positive input44 MICBIAS0 Microphone biasMicBias outputMic Bias Output Typ. Max UnitMICBIAS0 1.9 2.2 VMICBIAS0 current draw 2 mAMicrophone functional specificationSymbol Parameter Min. Typ. Max. UnitIDC Current consumption for one channel 1.5 mASINAD Signal to noise and distortion ratioInput level: -40 dBm0Input level: 0 dBm02969dBdBRIN Input impedance (differential) 13 20 27 KΩICN Idle channel noise -67 dBm0Vout Full Scale output voltage MIC0 1 VrmsMicrophone Type SupportExpedite L10-Gcan support ECM microphone and MEMS microphone.ECM Microphone reference circuit
16 novatelwireless.comMEMS Microphone reference circuitHeadsetPin No. Pin name Description9 ACCDET Headset Microphone Detect14 EAR_EINT Headset Detect (Internal PU, no needexternal PU circuit)36 MP3_OUT_L headset amplifier Left37 MP3_OUT_R headset amplifier Right
17 novatelwireless.comPin No. Pin name Description40 MIC1_IN- Microphone input (Headset)41 MIC1_IN+ Microphone input (Headset)Earphone functional specificationSymbol Parameter Min. Typ. Max. UnitFCK Clock frequency 6.5 MHzFs Sample rate 32 44.1 48 KHzIDC Current consumption 4 mAPSNR Peak signal to noise ratio 88 dBDR Dynamic range 88 dBVOUT Full Scale output voltage MP3_OUT 0.78 VrmsTHD Total harmonic distortion 10mW at 64Ω load -70 dBRLOAD Output resistor load 64 ΩCLOAD Output capacitor load 250 pFXT L-R channel cross talk 70 dBHeadset reference circuit
18 novatelwireless.comSpecific Absorption Rate (SAR) GuidelinesPortable RF exposure evaluation must be completed on host devices that provide ≤20.0 cmof separation distance between the transmitter antenna and the end user.Portable Device DefinitionThe FCC defines a Portable Device as a device having a transmitting antenna located at adistance ≤20cm from the user.Mobile Device DefinitionThe FCC defines a Mobile Device as a device having a transmitting antenna located at adistance ≥20cm from the user.SAR ComplianceEuropean and US certification bodies require that you test Specific Absorption Rate (SAR).SAR is a measure of energy absorbed by organic tissue over a specific time. The factors thataffect SAR readings are:loutput powerlfrequency of the radiationlproximity to antennalantenna counterpoiselduty cycleEarly in the physical design stage of the UE, the antenna and the mechanical engineeringdesign teams must collaborate on the design to ensure that they can meet the SARrequirements. Carefully reading and understanding the FCC requirements can help designerschoose the antenna type, the antenna location, and the industrial design of the UE. Theplacement and characteristics of the main antenna are the most critical factors affecting SARperformance.
19 novatelwireless.com3Tune Up ProceduresTune Up Procedure
20 novatelwireless.comTune Up ProcedureDuring manufacturing each device will be individually calibrated. Measurement is performedin a fully calibrated environment using an CMW500 base station simulator. The measurementprocedure is outlined below:Measurement Procedure:1. Set the device to operational voltage and on a predefined channel in a special testmode.2. The actual output power is measured at several power levels.3. The gain factors of each individual device are adjusted until the target value is met. Theappropriate gain control settings for each output power level are stored in each deviceindividually (for each power level). The user has no possibility to change these settingslater on.4. The maximum gains of each individual device are adjusted and measured until thetarget value is met. The production target power with tolerance compiles with themaximum power in test report.Maximum Target Power for Production Unit (dBm)Mode GSM 850 GSM 900 GSM 1800 GSM 1900GPRS 8 (1 Uplink) CS1 32.5 (+0.5/-0.7dB) 32.5 (+0.5/-0.7dB) 29.5 (+0.5/-0.7dB) 29.5 (+0.5/-0.7dB)GPRS 10 (2 Uplink) CS1 30 (+0.5/-0.7dB) 30 (+0.5/-0.7dB) 27 (+0.5/-0.7dB) 27 (+0.5/-0.7dB)GPRS 11 (3 Uplink) CS1 28.2 (+0.5/-0.7dB) 28.2 (+0.5/-0.7dB) 25.2 (+0.5/-0.7dB) 25.2 (+0.5/-0.7dB)GPRS 12 (4 Uplink) CS1 27 (+0.5/-0.7dB) 27 (+0.5/-0.7dB) 24 (+0.5/-0.7dB) 24 (+0.5/-0.7dB)

Navigation menu